From: Bai Ping <ping.bai-3arQi8VN3Tc@public.gmane.org>
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org
Cc: fabio.estevam-3arQi8VN3Tc@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-imx-3arQi8VN3Tc@public.gmane.org,
aisheng.dong-3arQi8VN3Tc@public.gmane.org,
jacky.baip-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org
Subject: [PATCH v3 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board
Date: Wed, 7 Feb 2018 10:11:21 +0800 [thread overview]
Message-ID: <1517969481-13411-2-git-send-email-ping.bai@nxp.com> (raw)
In-Reply-To: <1517969481-13411-1-git-send-email-ping.bai-3arQi8VN3Tc@public.gmane.org>
Add dts file support for imx6sll EVK board.
Signed-off-by: Bai Ping <ping.bai-3arQi8VN3Tc@public.gmane.org>
---
change v2->v3:
- use generic pinconfig binding
---
Documentation/devicetree/bindings/arm/fsl.txt | 4 +
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6sll-evk.dts | 374 ++++++++++++++++++++++++++
3 files changed, 380 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index cdb9dd7..8a1baa2 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -53,6 +53,10 @@ i.MX6 Quad SABRE Automotive Board
Required root node properties:
- compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
+i.MX6SLL EVK board
+Required root node properties:
+ - compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
+
Generic i.MX boards
-------------------
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38..28bff8b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -505,6 +505,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
dtb-$(CONFIG_SOC_IMX6SL) += \
imx6sl-evk.dtb \
imx6sl-warp.dtb
+dtb-$(CONFIG_SOC_IMX6SLL) += \
+ imx6sll-evk.dtb
dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-nitrogen6sx.dtb \
imx6sx-sabreauto.dtb \
diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts
new file mode 100644
index 0000000..e5a381a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sll-evk.dts
@@ -0,0 +1,374 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017-2018 NXP.
+ *
+ * SPDX-License-Identifier: (GPL-2.0 OR MIT)
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sll.dtsi"
+
+/ {
+ model = "Freescale i.MX6SLL EVK Board";
+ compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
+
+ memory {
+ reg = <0x80000000 0x80000000>;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
+
+ reg_usb_otg1_vbus: reg-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_otg2_vbus: reg-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_aud3v: reg-aud3v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-3v15";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-boot-on;
+ };
+
+ reg_aud4v: reg-aud4v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-4v2";
+ regulator-min-microvolt = <4325000>;
+ regulator-max-microvolt = <4325000>;
+ regulator-boot-on;
+ };
+
+ reg_lcd: reg-lcd {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-pwr";
+ gpio = <&gpio4 8 0>;
+ enable-active-high;
+ };
+
+ reg_sd1_vmmc: reg-sd1-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "SD1_SPWR";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&cpu0 {
+ arm-supply = <&sw1a_reg>;
+ soc-supply = <&sw1c_reg>;
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic: pfuze100@08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog0>, <&pinctrl_hog1>;
+
+ pinctrl_hog0: hog0grp {
+ pinmux = <
+ MX6SLL_PAD_KEY_ROW7__GPIO4_IO07
+ MX6SLL_PAD_GPIO4_IO22__GPIO4_IO22
+ MX6SLL_PAD_KEY_COL3__GPIO3_IO30
+ MX6SLL_PAD_KEY_COL4__GPIO4_IO00
+ MX6SLL_PAD_REF_CLK_32K__GPIO3_IO22 /* SD3 CD */
+ MX6SLL_PAD_KEY_COL6__GPIO4_IO04 /*SD3 RESET */
+ MX6SLL_PAD_KEY_COL5__GPIO4_IO02
+ MX6SLL_PAD_GPIO4_IO24__GPIO4_IO24 /* HP DETECT */
+ >;
+ slew-rate = <0x1>;
+ drive-strength = <0x3>;
+ fsl,pin-speed = <0x1>;
+ bias-pull-up = <0x1>;
+ input-schmitt-enable;
+ };
+
+ pinctrl_hog1: hog1grp {
+ pinmux = <
+ /*
+ * Must set the LVE of pad SD2_RESET, otherwise current
+ * leakage through eMMC chip will pull high the VCCQ to
+ * 2.6v, which will impact SD1 and SD3 SD3.0 voltage switch.
+ */
+ MX6SLL_PAD_SD2_RESET__GPIO4_IO27
+ >;
+ slew-rate = <0x1>;
+ drive-strength = <0x3>;
+ fsl,pin-speed = <0x1>;
+ bias-pull-up = <0x1>;
+ input-schmitt-enable;
+ fsl,low-voltage-enable = <0x1>;
+ };
+
+ pinctrl_uart1: uart1grp {
+ pinmux = <
+ MX6SLL_PAD_UART1_TXD__UART1_DCE_TX
+ MX6SLL_PAD_UART1_RXD__UART1_DCE_RX
+ >;
+ slew-rate = <0x1>;
+ drive-strength = <0x6>;
+ fsl,pin-speed = <0x2>;
+ bias-pull-up = <0x2>;
+ input-schmitt-enable;
+ };
+
+ pinctrl_usdhc1_data: usdhc1datagrp {
+ pinmux = <
+ MX6SLL_PAD_SD1_CMD__SD1_CMD
+ MX6SLL_PAD_SD1_DATA0__SD1_DATA0
+ MX6SLL_PAD_SD1_DATA1__SD1_DATA1
+ MX6SLL_PAD_SD1_DATA2__SD1_DATA2
+ MX6SLL_PAD_SD1_DATA3__SD1_DATA3
+ >;
+ slew-rate = <0x1>;
+ drive-strength = <0x4>;
+ fsl,pin-speed = <0x1>;
+ bias-pull-up = <0x1>;
+ input-schmitt-enable;
+ };
+
+ pinctrl_usdhc1_clk: usdhc1clkgrp {
+ pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>;
+ slew-rate = <0x1>;
+ drive-strength = <0x4>;
+ fsl,pin-speed = <0x1>;
+ bias-pull-down = <0x0>;
+ input-schmitt-enable;
+ };
+
+ pinctrl_usdhc1_data_100mhz: usdhc1datagrp_100mhz {
+ pinmux = <
+ MX6SLL_PAD_SD1_CMD__SD1_CMD
+ MX6SLL_PAD_SD1_DATA0__SD1_DATA0
+ MX6SLL_PAD_SD1_DATA1__SD1_DATA1
+ MX6SLL_PAD_SD1_DATA2__SD1_DATA2
+ MX6SLL_PAD_SD1_DATA3__SD1_DATA3
+ >;
+ slew-rate = <0x1>;
+ drive-strength = <0x4>;
+ fsl,pin-speed = <0x2>;
+ bias-pull-up = <0x1>;
+ input-schmitt-enable;
+ };
+
+ pinctrl_usdhc1_clk_100mhz: usdhc1clkgrp_100mhz {
+ pinmux = < MX6SLL_PAD_SD1_CLK__SD1_CLK>;
+ slew-rate = <0x1>;
+ drive-strength = <0x4>;
+ fsl,pin-speed = <0x2>;
+ bias-pull-down = <0x0>;
+ input-schmitt-enable;
+ };
+
+ pinctrl_usdhc1_data_200mhz: usdhc1datagrp_200mhz {
+ pinmux = <
+ MX6SLL_PAD_SD1_CMD__SD1_CMD
+ MX6SLL_PAD_SD1_DATA0__SD1_DATA0
+ MX6SLL_PAD_SD1_DATA1__SD1_DATA1
+ MX6SLL_PAD_SD1_DATA2__SD1_DATA2
+ MX6SLL_PAD_SD1_DATA3__SD1_DATA3
+ >;
+ slew-rate = <0x1>;
+ drive-strength = <0x5>;
+ fsl,pin-speed = <0x3>;
+ bias-pull-up = <0x1>;
+ input-schmitt-enable;
+ };
+
+ pinctrl_usdhc1_clk_200mhz: usdhc1clkgrp_200mhz {
+ pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>;
+ slew-rate = <0x1>;
+ drive-strength = <0x7>;
+ fsl,pin-speed = <0x3>;
+ bias-pull-down = <0x0>;
+ input-schmitt-enable;
+ };
+
+ pinctrl_usbotg1: usbotg1grp {
+ pinmux = <MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID>;
+ slew-rate = <0x1>;
+ drive-strength = <0x3>;
+ fsl,pin-speed = <0x1>;
+ bias-pull-up = <0x1>;
+ input-schmitt-enable;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ pinmux = <
+ MX6SLL_PAD_I2C1_SCL__I2C1_SCL
+ MX6SLL_PAD_I2C1_SDA__I2C1_SDA
+ >;
+ slew-rate = <0x1>;
+ drive-strength = <0x6>;
+ fsl,pin-speed = <0x2>;
+ drive-open-drain;
+ bias-pull-up = <0x2>;
+ input-schmitt-enable;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1_data>, <&pinctrl_usdhc1_clk>;
+ pinctrl-1 = <&pinctrl_usdhc1_data_100mhz>, <&pinctrl_usdhc1_clk_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_data_200mhz>, <&pinctrl_usdhc1_clk_200mhz>;
+ cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ vmmc-supply = <®_sd1_vmmc>;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ disable-over-current;
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_otg2_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2018-02-07 2:11 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-02-07 2:11 [PATCH v3 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll Bai Ping
[not found] ` <1517969481-13411-1-git-send-email-ping.bai-3arQi8VN3Tc@public.gmane.org>
2018-02-07 2:11 ` Bai Ping [this message]
[not found] ` <1517969481-13411-2-git-send-email-ping.bai-3arQi8VN3Tc@public.gmane.org>
2018-02-07 2:44 ` [PATCH v3 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board Fabio Estevam
[not found] ` <CAOMZO5DEvVsGbbG_w116OX625DJos0GHsmjUUBkgwVk7NLONMw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2018-02-07 2:52 ` Jacky Bai
2018-02-07 2:52 ` [PATCH v3 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll Fabio Estevam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1517969481-13411-2-git-send-email-ping.bai@nxp.com \
--to=ping.bai-3arqi8vn3tc@public.gmane.org \
--cc=aisheng.dong-3arQi8VN3Tc@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=fabio.estevam-3arQi8VN3Tc@public.gmane.org \
--cc=jacky.baip-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-imx-3arQi8VN3Tc@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).