From mboxrd@z Thu Jan 1 00:00:00 1970 From: Vishal Sagar Subject: [PATCH v9 1/2] media: dt-bindings: media: xilinx: Add Xilinx MIPI CSI-2 Rx Subsystem Date: Tue, 11 Jun 2019 15:40:08 +0530 Message-ID: <1560247809-117978-2-git-send-email-vishal.sagar@xilinx.com> References: <1560247809-117978-1-git-send-email-vishal.sagar@xilinx.com> Mime-Version: 1.0 Content-Type: text/plain Return-path: In-Reply-To: <1560247809-117978-1-git-send-email-vishal.sagar@xilinx.com> Sender: linux-kernel-owner@vger.kernel.org To: Hyun Kwon , laurent.pinchart@ideasonboard.com, mchehab@kernel.org, robh+dt@kernel.org, mark.rutland@arm.com, Michal Simek , linux-media@vger.kernel.org, devicetree@vger.kernel.org, hans.verkuil@cisco.com, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, Dinesh Kumar , Sandip Kothari , Luca Ceresoli , Jacopo Mondi Cc: Vishal Sagar List-Id: devicetree@vger.kernel.org Add bindings documentation for Xilinx MIPI CSI-2 Rx Subsystem. The Xilinx MIPI CSI-2 Rx Subsystem consists of a CSI-2 Rx controller, a DPHY in Rx mode, an optional I2C controller and a Video Format Bridge. Signed-off-by: Vishal Sagar Reviewed-by: Hyun Kwon Reviewed-by: Rob Herring Reviewed-by: Luca Ceresoli --- v9 - Fix xlnx,vfb description. - s/Optional/Required endpoint property. - Move data-lanes description from Ports to endpoint property section. v8 - Added reset-gpios optional property to assert video_aresetn v7 - Removed the control name from dt bindings - Updated the example dt node name to csi2rx v6 - Added "control" after V4L2_CID_XILINX_MIPICSISS_ACT_LANES as suggested by Luca - Added reviewed by Rob Herring v5 - Incorporated comments by Luca Cersoli - Removed DPHY clock from description and example - Removed bayer pattern from device tree MIPI CSI IP doesn't deal with bayer pattern. v4 - Added reviewed by Hyun Kwon v3 - removed interrupt parent as suggested by Rob - removed dphy clock - moved vfb to optional properties - Added required and optional port properties section - Added endpoint property section v2 - updated the compatible string to latest version supported - removed DPHY related parameters - added CSI v2.0 related property (including VCX for supporting upto 16 virtual channels). - modified csi-pxl-format from string to unsigned int type where the value is as per the CSI specification - Defined port 0 and port 1 as sink and source ports. - Removed max-lanes property as suggested by Rob and Sakari .../bindings/media/xilinx/xlnx,csi2rxss.txt | 116 +++++++++++++++++++++ 1 file changed, 116 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt new file mode 100644 index 0000000..913b28d --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.txt @@ -0,0 +1,116 @@ +Xilinx MIPI CSI2 Receiver Subsystem Device Tree Bindings +-------------------------------------------------------- + +The Xilinx MIPI CSI2 Receiver Subsystem is used to capture MIPI CSI2 traffic +from compliant camera sensors and send the output as AXI4 Stream video data +for image processing. + +The subsystem consists of a MIPI DPHY in slave mode which captures the +data packets. This is passed along the MIPI CSI2 Rx IP which extracts the +packet data. The optional Video Format Bridge (VFB) converts this data to +AXI4 Stream video data. + +For more details, please refer to PG232 Xilinx MIPI CSI-2 Receiver Subsystem. + +Required properties: +-------------------- +- compatible: Must contain "xlnx,mipi-csi2-rx-subsystem-4.0". +- reg: Physical base address and length of the registers set for the device. +- interrupts: Property with a value describing the interrupt number. +- clocks: List of phandles to AXI Lite and Video clocks. +- clock-names: Must contain "lite_aclk" and "video_aclk" in the same order + as clocks listed in clocks property. +- xlnx,csi-pxl-format: This denotes the CSI Data type selected in hw design. + Packets other than this data type (except for RAW8 and User defined data + types) will be filtered out. Possible values are as below - + 0x1E - YUV4228B + 0x1F - YUV42210B + 0x20 - RGB444 + 0x21 - RGB555 + 0x22 - RGB565 + 0x23 - RGB666 + 0x24 - RGB888 + 0x28 - RAW6 + 0x29 - RAW7 + 0x2A - RAW8 + 0x2B - RAW10 + 0x2C - RAW12 + 0x2D - RAW14 + 0x2E - RAW16 + 0x2F - RAW20 + + +Optional properties: +-------------------- +- xlnx,vfb: Present when Video Format Bridge is enabled in IP configuration +- xlnx,en-csi-v2-0: Present if CSI v2 is enabled in IP configuration. +- xlnx,en-vcx: When present, there are maximum 16 virtual channels, else + only 4. This is present only if xlnx,en-csi-v2-0 is present. +- xlnx,en-active-lanes: present if the number of active lanes can be + re-configured at runtime in the Protocol Configuration Register. + Otherwise all lanes, as set in IP configuration, are always active. +- reset-gpios: Optional specifier for a GPIO that asserts video_aresetn. + +Ports +----- +The device node shall contain two 'port' child nodes as defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +The port@0 is a sink port and shall connect to CSI2 source like camera. + +The port@1 is a source port and can be connected to any video processing IP +which can work with AXI4 Stream data. + +Required port properties: +-------------------- +- reg: 0 - for sink port. + 1 - for source port. + +Required endpoint property: +--------------------------- +- data-lanes: specifies MIPI CSI-2 data lanes as covered in video-interfaces.txt. + This is required only in the sink port 0 endpoint which connects to MIPI CSI2 + source like sensor. The possible values are: + 1 - For 1 lane enabled in IP. + 1 2 - For 2 lanes enabled in IP. + 1 2 3 - For 3 lanes enabled in IP. + 1 2 3 4 - For 4 lanes enabled in IP. + +Example: + + xcsi2rxss_1: csi2rx@a0020000 { + compatible = "xlnx,mipi-csi2-rx-subsystem-4.0"; + reg = <0x0 0xa0020000 0x0 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 95 4>; + xlnx,csi-pxl-format = <0x2a>; + xlnx,vfb; + xlnx,en-active-lanes; + xlnx,en-csi-v2-0; + xlnx,en-vcx; + clock-names = "lite_aclk", "video_aclk"; + clocks = <&misc_clk_0>, <&misc_clk_1>; + reset-gpios = <&gpio 86 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + /* Sink port */ + reg = <0>; + csiss_in: endpoint { + data-lanes = <1 2 3 4>; + /* MIPI CSI2 Camera handle */ + remote-endpoint = <&camera_out>; + }; + }; + port@1 { + /* Source port */ + reg = <1>; + csiss_out: endpoint { + remote-endpoint = <&vproc_in>; + }; + }; + }; + }; -- 1.8.3.1