devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Paul Cercueil <paul@crapouillou.net>
To: "周琰杰 (Zhou Yanjie)" <zhouyanjie@wanyeetech.com>
Cc: linux-mips@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
	mturquette@baylibre.com, sboyd@kernel.org, robh+dt@kernel.org,
	mark.rutland@arm.com
Subject: Re: [PATCH v5 2/6] clk: Ingenic: Adjust cgu code to make it compatible with X1830.
Date: Fri, 14 Feb 2020 15:49:18 -0300	[thread overview]
Message-ID: <1581706158.3.4@crapouillou.net> (raw)
In-Reply-To: <1581701262-110556-4-git-send-email-zhouyanjie@wanyeetech.com>

Hi Zhou,


Le sam., févr. 15, 2020 at 01:27, 周琰杰 (Zhou Yanjie) 
<zhouyanjie@wanyeetech.com> a écrit :
> The PLL of X1830 Soc from Ingenic has been greatly changed,
> the bypass control is placed in another register, so now two
> registers may needed to control the PLL. To this end, the
> original "reg" was changed to "pll_reg", and a new "bypass_reg"
> was introduced. In addition, when calculating rate, the PLL of
> X1830 introduced an extra 2x multiplier, so a new "rate_multiplier"
> was introduced. And adjust the code in jz47xx-cgu.c and x1000-cgu.c,
> make it to be compatible with the new cgu code.
> 
> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
> ---
> 
> Notes:
>     v1->v2:
>     1.Use two fields (pll_reg & bypass_reg) instead of the 2-values
>       array (reg[2]).
>     2.Remove the "pll_info->version" and add a 
> "pll_info->rate_multiplier".
>     3.Fix the coding style and add more detailed commit message.
>     4.Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
>       to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
>       the old mailbox is in an unstable state.
> 
>     v2->v3:
>     Adjust order from [1/5] in v2 to [2/5] in v3.
> 
>     v3->v4:
>     Merge [3/5] in v3 into this patch.
> 
>     v4->v5:
>     Rebase on top of kernel 5.6-rc1.
> 
>  drivers/clk/ingenic/cgu.c         | 32 
> +++++++++++++++++++++-----------
>  drivers/clk/ingenic/cgu.h         |  8 ++++++--
>  drivers/clk/ingenic/jz4725b-cgu.c |  4 +++-
>  drivers/clk/ingenic/jz4740-cgu.c  |  4 +++-
>  drivers/clk/ingenic/jz4770-cgu.c  |  8 ++++++--
>  drivers/clk/ingenic/jz4780-cgu.c  |  4 +++-
>  drivers/clk/ingenic/x1000-cgu.c   |  8 ++++++--
>  7 files changed, 48 insertions(+), 20 deletions(-)
> 
> diff --git a/drivers/clk/ingenic/cgu.c b/drivers/clk/ingenic/cgu.c
> index ab1302a..7d859e4 100644
> --- a/drivers/clk/ingenic/cgu.c
> +++ b/drivers/clk/ingenic/cgu.c
> @@ -82,7 +82,7 @@ ingenic_pll_recalc_rate(struct clk_hw *hw, unsigned 
> long parent_rate)
>  	BUG_ON(clk_info->type != CGU_CLK_PLL);
>  	pll_info = &clk_info->pll;
> 
> -	ctl = readl(cgu->base + pll_info->reg);
> +	ctl = readl(cgu->base + pll_info->pll_reg);
> 
>  	m = (ctl >> pll_info->m_shift) & GENMASK(pll_info->m_bits - 1, 0);
>  	m += pll_info->m_offset;
> @@ -90,6 +90,9 @@ ingenic_pll_recalc_rate(struct clk_hw *hw, unsigned 
> long parent_rate)
>  	n += pll_info->n_offset;
>  	od_enc = ctl >> pll_info->od_shift;
>  	od_enc &= GENMASK(pll_info->od_bits - 1, 0);
> +
> +	ctl = readl(cgu->base + pll_info->bypass_reg);
> +
>  	bypass = !pll_info->no_bypass_bit &&
>  		 !!(ctl & BIT(pll_info->bypass_bit));
> 
> @@ -103,7 +106,8 @@ ingenic_pll_recalc_rate(struct clk_hw *hw, 
> unsigned long parent_rate)
>  	BUG_ON(od == pll_info->od_max);
>  	od++;
> 
> -	return div_u64((u64)parent_rate * m, n * od);
> +	return div_u64((u64)parent_rate * m * pll_info->rate_multiplier,
> +		n * od);
>  }
> 
>  static unsigned long
> @@ -136,7 +140,8 @@ ingenic_pll_calc(const struct 
> ingenic_cgu_clk_info *clk_info,
>  	if (pod)
>  		*pod = od;
> 
> -	return div_u64((u64)parent_rate * m, n * od);
> +	return div_u64((u64)parent_rate * m * pll_info->rate_multiplier,
> +		n * od);
>  }
> 
>  static inline const struct ingenic_cgu_clk_info *to_clk_info(
> @@ -180,7 +185,7 @@ ingenic_pll_set_rate(struct clk_hw *hw, unsigned 
> long req_rate,
>  			clk_info->name, req_rate, rate);
> 
>  	spin_lock_irqsave(&cgu->lock, flags);
> -	ctl = readl(cgu->base + pll_info->reg);
> +	ctl = readl(cgu->base + pll_info->pll_reg);
> 
>  	ctl &= ~(GENMASK(pll_info->m_bits - 1, 0) << pll_info->m_shift);
>  	ctl |= (m - pll_info->m_offset) << pll_info->m_shift;
> @@ -191,7 +196,7 @@ ingenic_pll_set_rate(struct clk_hw *hw, unsigned 
> long req_rate,
>  	ctl &= ~(GENMASK(pll_info->od_bits - 1, 0) << pll_info->od_shift);
>  	ctl |= pll_info->od_encoding[od - 1] << pll_info->od_shift;
> 
> -	writel(ctl, cgu->base + pll_info->reg);
> +	writel(ctl, cgu->base + pll_info->pll_reg);
>  	spin_unlock_irqrestore(&cgu->lock, flags);
> 
>  	return 0;
> @@ -209,16 +214,21 @@ static int ingenic_pll_enable(struct clk_hw *hw)
>  	u32 ctl;
> 
>  	spin_lock_irqsave(&cgu->lock, flags);
> -	ctl = readl(cgu->base + pll_info->reg);
> +	ctl = readl(cgu->base + pll_info->bypass_reg);
> 
>  	ctl &= ~BIT(pll_info->bypass_bit);
> +
> +	writel(ctl, cgu->base + pll_info->bypass_reg);
> +
> +	ctl = readl(cgu->base + pll_info->pll_reg);
> +
>  	ctl |= BIT(pll_info->enable_bit);
> 
> -	writel(ctl, cgu->base + pll_info->reg);
> +	writel(ctl, cgu->base + pll_info->pll_reg);
> 
>  	/* wait for the PLL to stabilise */
>  	for (i = 0; i < timeout; i++) {
> -		ctl = readl(cgu->base + pll_info->reg);
> +		ctl = readl(cgu->base + pll_info->pll_reg);
>  		if (ctl & BIT(pll_info->stable_bit))
>  			break;
>  		mdelay(1);
> @@ -242,11 +252,11 @@ static void ingenic_pll_disable(struct clk_hw 
> *hw)
>  	u32 ctl;
> 
>  	spin_lock_irqsave(&cgu->lock, flags);
> -	ctl = readl(cgu->base + pll_info->reg);
> +	ctl = readl(cgu->base + pll_info->pll_reg);
> 
>  	ctl &= ~BIT(pll_info->enable_bit);
> 
> -	writel(ctl, cgu->base + pll_info->reg);
> +	writel(ctl, cgu->base + pll_info->pll_reg);
>  	spin_unlock_irqrestore(&cgu->lock, flags);
>  }
> 
> @@ -258,7 +268,7 @@ static int ingenic_pll_is_enabled(struct clk_hw 
> *hw)
>  	const struct ingenic_cgu_pll_info *pll_info = &clk_info->pll;
>  	u32 ctl;
> 
> -	ctl = readl(cgu->base + pll_info->reg);
> +	ctl = readl(cgu->base + pll_info->pll_reg);
> 
>  	return !!(ctl & BIT(pll_info->enable_bit));
>  }
> diff --git a/drivers/clk/ingenic/cgu.h b/drivers/clk/ingenic/cgu.h
> index 0dc8004..f7b6908 100644
> --- a/drivers/clk/ingenic/cgu.h
> +++ b/drivers/clk/ingenic/cgu.h
> @@ -16,7 +16,9 @@
> 
>  /**
>   * struct ingenic_cgu_pll_info - information about a PLL
> - * @reg: the offset of the PLL's control register within the CGU
> + * @pll_reg: the offset of the PLL's control register within the CGU
> + * @bypass_reg: the offset of the bypass control register within the 
> CGU
> + * @rate_multiplier: the multiplier needed by pll rate calculation
>   * @m_shift: the number of bits to shift the multiplier value by 
> (ie. the
>   *           index of the lowest bit of the multiplier value in the 
> PLL's
>   *           control register)
> @@ -43,7 +45,9 @@
>   * @no_bypass_bit: if set, the PLL has no bypass functionality
>   */
>  struct ingenic_cgu_pll_info {
> -	unsigned reg;
> +	unsigned pll_reg;

I'd prefer that you don't rename 'reg' to 'pll_reg', this patch would 
be ten times smaller if you don't.

-Paul

> +	unsigned bypass_reg;
> +	unsigned rate_multiplier;
>  	const s8 *od_encoding;
>  	u8 m_shift, m_bits, m_offset;
>  	u8 n_shift, n_bits, n_offset;
> diff --git a/drivers/clk/ingenic/jz4725b-cgu.c 
> b/drivers/clk/ingenic/jz4725b-cgu.c
> index a3b4635..0b05167 100644
> --- a/drivers/clk/ingenic/jz4725b-cgu.c
> +++ b/drivers/clk/ingenic/jz4725b-cgu.c
> @@ -53,7 +53,9 @@ static const struct ingenic_cgu_clk_info 
> jz4725b_cgu_clocks[] = {
>  		"pll", CGU_CLK_PLL,
>  		.parents = { JZ4725B_CLK_EXT, -1, -1, -1 },
>  		.pll = {
> -			.reg = CGU_REG_CPPCR,
> +			.pll_reg = CGU_REG_CPPCR,
> +			.bypass_reg = CGU_REG_CPPCR,
> +			.rate_multiplier = 1,
>  			.m_shift = 23,
>  			.m_bits = 9,
>  			.m_offset = 2,
> diff --git a/drivers/clk/ingenic/jz4740-cgu.c 
> b/drivers/clk/ingenic/jz4740-cgu.c
> index 4f0e92c..78f31df 100644
> --- a/drivers/clk/ingenic/jz4740-cgu.c
> +++ b/drivers/clk/ingenic/jz4740-cgu.c
> @@ -68,7 +68,9 @@ static const struct ingenic_cgu_clk_info 
> jz4740_cgu_clocks[] = {
>  		"pll", CGU_CLK_PLL,
>  		.parents = { JZ4740_CLK_EXT, -1, -1, -1 },
>  		.pll = {
> -			.reg = CGU_REG_CPPCR,
> +			.pll_reg = CGU_REG_CPPCR,
> +			.bypass_reg = CGU_REG_CPPCR,
> +			.rate_multiplier = 1,
>  			.m_shift = 23,
>  			.m_bits = 9,
>  			.m_offset = 2,
> diff --git a/drivers/clk/ingenic/jz4770-cgu.c 
> b/drivers/clk/ingenic/jz4770-cgu.c
> index 956dd65..32e476d 100644
> --- a/drivers/clk/ingenic/jz4770-cgu.c
> +++ b/drivers/clk/ingenic/jz4770-cgu.c
> @@ -101,7 +101,9 @@ static const struct ingenic_cgu_clk_info 
> jz4770_cgu_clocks[] = {
>  		"pll0", CGU_CLK_PLL,
>  		.parents = { JZ4770_CLK_EXT },
>  		.pll = {
> -			.reg = CGU_REG_CPPCR0,
> +			.pll_reg = CGU_REG_CPPCR0,
> +			.bypass_reg = CGU_REG_CPPCR0,
> +			.rate_multiplier = 1,
>  			.m_shift = 24,
>  			.m_bits = 7,
>  			.m_offset = 1,
> @@ -123,7 +125,9 @@ static const struct ingenic_cgu_clk_info 
> jz4770_cgu_clocks[] = {
>  		"pll1", CGU_CLK_PLL,
>  		.parents = { JZ4770_CLK_EXT },
>  		.pll = {
> -			.reg = CGU_REG_CPPCR1,
> +			.pll_reg = CGU_REG_CPPCR1,
> +			.bypass_reg = CGU_REG_CPPCR1,
> +			.rate_multiplier = 1,
>  			.m_shift = 24,
>  			.m_bits = 7,
>  			.m_offset = 1,
> diff --git a/drivers/clk/ingenic/jz4780-cgu.c 
> b/drivers/clk/ingenic/jz4780-cgu.c
> index ea905ff..d07fff1 100644
> --- a/drivers/clk/ingenic/jz4780-cgu.c
> +++ b/drivers/clk/ingenic/jz4780-cgu.c
> @@ -220,7 +220,9 @@ static const struct ingenic_cgu_clk_info 
> jz4780_cgu_clocks[] = {
>  	/* PLLs */
> 
>  #define DEF_PLL(name) { \
> -	.reg = CGU_REG_ ## name, \
> +	.pll_reg = CGU_REG_ ## name, \
> +	.bypass_reg = CGU_REG_ ## name, \
> +	.rate_multiplier = 1, \
>  	.m_shift = 19, \
>  	.m_bits = 13, \
>  	.m_offset = 1, \
> diff --git a/drivers/clk/ingenic/x1000-cgu.c 
> b/drivers/clk/ingenic/x1000-cgu.c
> index b22d87b..d6fe28f 100644
> --- a/drivers/clk/ingenic/x1000-cgu.c
> +++ b/drivers/clk/ingenic/x1000-cgu.c
> @@ -57,7 +57,9 @@ static const struct ingenic_cgu_clk_info 
> x1000_cgu_clocks[] = {
>  		"apll", CGU_CLK_PLL,
>  		.parents = { X1000_CLK_EXCLK, -1, -1, -1 },
>  		.pll = {
> -			.reg = CGU_REG_APLL,
> +			.pll_reg = CGU_REG_APLL,
> +			.bypass_reg = CGU_REG_APLL,
> +			.rate_multiplier = 1,
>  			.m_shift = 24,
>  			.m_bits = 7,
>  			.m_offset = 1,
> @@ -78,7 +80,9 @@ static const struct ingenic_cgu_clk_info 
> x1000_cgu_clocks[] = {
>  		"mpll", CGU_CLK_PLL,
>  		.parents = { X1000_CLK_EXCLK, -1, -1, -1 },
>  		.pll = {
> -			.reg = CGU_REG_MPLL,
> +			.pll_reg = CGU_REG_MPLL,
> +			.bypass_reg = CGU_REG_MPLL,
> +			.rate_multiplier = 1,
>  			.m_shift = 24,
>  			.m_bits = 7,
>  			.m_offset = 1,
> --
> 2.7.4
> 



  reply	other threads:[~2020-02-14 18:49 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-02-14 17:27 Add support for the X1830 and fix bugs for X1000 v5 周琰杰 (Zhou Yanjie)
2020-02-14 17:27 ` [PATCH v5 0/6] " 周琰杰 (Zhou Yanjie)
2020-02-14 17:27 ` [PATCH v5 1/6] clk: Ingenic: Remove unnecessary spinlock when reading registers 周琰杰 (Zhou Yanjie)
2020-02-14 17:27 ` [PATCH v5 2/6] clk: Ingenic: Adjust cgu code to make it compatible with X1830 周琰杰 (Zhou Yanjie)
2020-02-14 18:49   ` Paul Cercueil [this message]
2020-02-15 14:07     ` Zhou Yanjie
2020-02-14 17:27 ` [PATCH v5 3/6] dt-bindings: clock: Add X1830 bindings 周琰杰 (Zhou Yanjie)
2020-02-14 17:27 ` [PATCH v5 4/6] clk: Ingenic: Add CGU driver for X1830 周琰杰 (Zhou Yanjie)
2020-02-14 17:27 ` [PATCH v5 5/6] dt-bindings: clock: Add and reorder ABI for X1000 周琰杰 (Zhou Yanjie)
2020-02-18 21:05   ` Rob Herring
2020-02-14 17:27 ` [PATCH v5 6/6] clk: X1000: Add FIXDIV for SSI clock of X1000 周琰杰 (Zhou Yanjie)

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1581706158.3.4@crapouillou.net \
    --to=paul@crapouillou.net \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mips@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mturquette@baylibre.com \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    --cc=zhouyanjie@wanyeetech.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).