From: Kathiravan T <kathirav@codeaurora.org>
To: agross@kernel.org, bjorn.andersson@linaro.org,
robh+dt@kernel.org, lgirdwood@gmail.com, broonie@kernel.org,
sivaprak@codeaurora.org, kathirav@codeaurora.org,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 3/3] arm64: dts: ipq6018: enable DVFS support
Date: Thu, 30 Jul 2020 14:19:24 +0530 [thread overview]
Message-ID: <1596098964-19878-4-git-send-email-kathirav@codeaurora.org> (raw)
In-Reply-To: <1596098964-19878-1-git-send-email-kathirav@codeaurora.org>
Add A53 PLL, APCS clock, RPM Glink, RPM message RAM, cpu-opp-table,
SMPA2 regulator to enable the cpu frequency on IPQ6018.
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Kathiravan T <kathirav@codeaurora.org>
---
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 96 +++++++++++++++++++++++++++++++++--
1 file changed, 93 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 1aa8d8579463..a94dac76bf3f 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-ipq6018.h>
#include <dt-bindings/reset/qcom,gcc-ipq6018.h>
+#include <dt-bindings/clock/qcom,apss-ipq.h>
/ {
#address-cells = <2>;
@@ -38,6 +39,10 @@
reg = <0x0>;
enable-method = "psci";
next-level-cache = <&L2_0>;
+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
+ clock-names = "cpu";
+ operating-points-v2 = <&cpu_opp_table>;
+ cpu-supply = <&ipq6018_s2>;
};
CPU1: cpu@1 {
@@ -46,6 +51,10 @@
enable-method = "psci";
reg = <0x1>;
next-level-cache = <&L2_0>;
+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
+ clock-names = "cpu";
+ operating-points-v2 = <&cpu_opp_table>;
+ cpu-supply = <&ipq6018_s2>;
};
CPU2: cpu@2 {
@@ -54,6 +63,10 @@
enable-method = "psci";
reg = <0x2>;
next-level-cache = <&L2_0>;
+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
+ clock-names = "cpu";
+ operating-points-v2 = <&cpu_opp_table>;
+ cpu-supply = <&ipq6018_s2>;
};
CPU3: cpu@3 {
@@ -62,6 +75,10 @@
enable-method = "psci";
reg = <0x3>;
next-level-cache = <&L2_0>;
+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
+ clock-names = "cpu";
+ operating-points-v2 = <&cpu_opp_table>;
+ cpu-supply = <&ipq6018_s2>;
};
L2_0: l2-cache {
@@ -70,6 +87,42 @@
};
};
+ cpu_opp_table: cpu_opp_table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-864000000 {
+ opp-hz = /bits/ 64 <864000000>;
+ opp-microvolt = <725000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <787500>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1320000000 {
+ opp-hz = /bits/ 64 <1320000000>;
+ opp-microvolt = <862500>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <925000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1608000000 {
+ opp-hz = /bits/ 64 <1608000000>;
+ opp-microvolt = <987500>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1800000000 {
+ opp-hz = /bits/ 64 <1800000000>;
+ opp-microvolt = <1062500>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
firmware {
scm {
compatible = "qcom,scm";
@@ -98,6 +151,11 @@
#size-cells = <2>;
ranges;
+ rpm_msg_ram: memory@0x60000 {
+ reg = <0x0 0x60000 0x0 0x6000>;
+ no-map;
+ };
+
tz: tz@48500000 {
reg = <0x0 0x48500000 0x0 0x00200000>;
no-map;
@@ -294,12 +352,22 @@
};
apcs_glb: mailbox@b111000 {
- compatible = "qcom,ipq8074-apcs-apps-global";
- reg = <0x0b111000 0xc>;
-
+ compatible = "qcom,ipq6018-apcs-apps-global";
+ reg = <0x0b111000 0x1000>;
+ #clock-cells = <1>;
+ clocks = <&a53pll>, <&xo>;
+ clock-names = "pll", "xo";
#mbox-cells = <1>;
};
+ a53pll: clock@b116000 {
+ compatible = "qcom,ipq6018-a53pll";
+ reg = <0x0b116000 0x40>;
+ #clock-cells = <0>;
+ clocks = <&xo>;
+ clock-names = "xo";
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -440,4 +508,26 @@
#interrupt-cells = <2>;
};
};
+
+ rpm-glink {
+ compatible = "qcom,glink-rpm";
+ interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+ mboxes = <&apcs_glb 0>;
+
+ rpm_requests: glink-channel {
+ compatible = "qcom,rpm-ipq6018";
+ qcom,glink-channels = "rpm_requests";
+
+ regulators {
+ compatible = "qcom,rpm-mp5496-regulators";
+
+ ipq6018_s2: s2 {
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1062500>;
+ regulator-always-on;
+ };
+ };
+ };
+ };
};
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2020-07-30 8:49 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-30 8:49 [PATCH 0/3] Enable DVFS support for IPQ6018 Kathiravan T
2020-07-30 8:49 ` [PATCH 1/3] dt-bindings: mailbox: add compatible for the IPQ6018 SoC Kathiravan T
2020-07-31 22:28 ` Rob Herring
2020-07-30 8:49 ` [PATCH 2/3] dt-bindings: regulator: add the sub node names for the MP5496 PMIC Kathiravan T
2020-07-30 8:49 ` Kathiravan T [this message]
2020-07-30 21:47 ` [PATCH 3/3] arm64: dts: ipq6018: enable DVFS support kernel test robot
2020-07-30 22:28 ` [PATCH 0/3] Enable DVFS support for IPQ6018 Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1596098964-19878-4-git-send-email-kathirav@codeaurora.org \
--to=kathirav@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=sivaprak@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).