Re: [PATCH 3/5] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac

[Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>]

On Fri, Jun 03, 2016 at 11:56:28AM +0200, LABBE Corentin wrote:
> This patch adds documentation for Device-Tree bindings for the
> Allwinner sun8i-emac driver.
> 
> Signed-off-by: LABBE Corentin <clabbe.montjoie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  .../bindings/net/allwinner,sun8i-emac.txt          | 64 ++++++++++++++++++++++
>  1 file changed, 64 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> 
> diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> new file mode 100644
> index 0000000..cf71a71
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> @@ -0,0 +1,64 @@
> +* Allwinner sun8i EMAC ethernet controller
> +
> +Required properties:
> +- compatible: "allwinner,sun8i-a83t-emac", "allwinner,sun8i-h3-emac",
> +		or "allwinner,sun50i-a64-emac"
> +- reg: address and length of the register sets for the device.
> +- reg-names: should be "emac" and "syscon", matching the register sets

Is syscon shared with other devices? Your example only has 1 reg 
address.

> +- interrupts: interrupt for the device
> +- clocks: A phandle to the reference clock for this device
> +- clock-names: should be "ahb"
> +- resets: A phandle to the reset control for this device
> +- reset-names: should be "ahb"
> +- phy-mode: See ethernet.txt
> +- phy or phy-handle: See ethernet.txt
> +- #address-cells: shall be 1
> +- #size-cells: shall be 0
> +
> +"allwinner,sun8i-h3-emac" also requires:
> +- clocks: an extra phandle to the reference clock for the EPHY
> +- clock-names: an extra "ephy" entry matching the clocks property
> +- resets: an extra phandle to the reset control for the EPHY
> +- resets-names: an extra "ephy" entry matching the resets property
> +
> +See ethernet.txt in the same directory for generic bindings for ethernet
> +controllers.
> +
> +The device node referenced by "phy" or "phy-handle" should be a child node
> +of this node. See phy.txt for the generic PHY bindings.
> +
> +Optional properties:
> +- phy-supply: phandle to a regulator if the PHY needs one
> +- phy-io-supply: phandle to a regulator if the PHY needs a another one for I/O.
> +		 This is sometimes found with RGMII PHYs, which use a second
> +		 regulator for the lower I/O voltage.

These should go in the phy's node.

> +- allwinner,tx-delay: The setting of the TX clock delay chain
> +- allwinner,rx-delay: The setting of the RX clock delay chain
> +
> +The TX/RX clock delay chain settings are board specific.
> +
> +Optional properties for "allwinner,sun8i-h3-emac":
> +- allwinner,use-internal-phy: Use the H3 SoC's internal E(thernet) PHY
> +- allwinner,leds-active-low: EPHY LEDs are active low
> +
> +When the internal PHY is requested, the implementation shall configure the
> +internal PHY to use the address specified in the child PHY node.
> +
> +Example:
> +
> +emac: ethernet@01c0b000 {
> +	compatible = "allwinner,sun8i-h3-emac";
> +	reg = <0x01c0b000 0x1000>;
> +	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> +	clocks = <&bus_gates 17>, <&bus_gates 128>;
> +	clock-names = "ahb", "ephy";
> +	resets = <&ahb_rst 17>, <&ahb_rst 66>;
> +	reset-names = "ahb", "ephy";
> +	phy = <&phy1>;
> +	allwinner,use-internal-phy;
> +	allwinner,leds-active-low;
> +
> +	phy1: ethernet-phy@1 {
> +		reg = <1>;
> +	};
> +};
> -- 
> 2.7.3
>