From: Stefan Agner <stefan@agner.ch>
To: shawnguo@kernel.org, kernel@pengutronix.de
Cc: fabio.estevam@nxp.com, robh+dt@kernel.org, mark.rutland@arm.com,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, Stefan Agner <stefan@agner.ch>
Subject: [PATCH 3/9] ARM: dts: imx7-colibri: mux pull-ups where appropriate
Date: Wed, 6 Dec 2017 16:29:59 +0100 [thread overview]
Message-ID: <20171206153005.6144-3-stefan@agner.ch> (raw)
In-Reply-To: <20171206153005.6144-1-stefan@agner.ch>
Use pull-ups instead of pull-downs for the pins which are already
pulled-up externally.
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
arch/arm/boot/dts/imx7-colibri.dtsi | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index dae6b561145b..e4e32aa786f4 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -307,17 +307,17 @@
pinctrl_gpio1: gpio1-grp {
fsl,pins = <
- MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3 0x14 /* SODIMM 55 */
- MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2 0x14 /* SODIMM 63 */
+ MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3 0x74 /* SODIMM 55 */
+ MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2 0x74 /* SODIMM 63 */
MX7D_PAD_SD1_RESET_B__GPIO5_IO2 0X14 /* SODIMM 73 */
- MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 0X14 /* SODIMM 77 */
+ MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 0x14 /* SODIMM 77 */
MX7D_PAD_EPDC_DATA09__GPIO2_IO9 0x14 /* SODIMM 89 */
- MX7D_PAD_EPDC_DATA08__GPIO2_IO8 0x14 /* SODIMM 91 */
+ MX7D_PAD_EPDC_DATA08__GPIO2_IO8 0x74 /* SODIMM 91 */
MX7D_PAD_LCD_RESET__GPIO3_IO4 0x14 /* SODIMM 93 */
MX7D_PAD_EPDC_DATA13__GPIO2_IO13 0x14 /* SODIMM 95 */
MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11 0x14 /* SODIMM 99 */
- MX7D_PAD_EPDC_DATA10__GPIO2_IO10 0x14 /* SODIMM 105 */
- MX7D_PAD_EPDC_DATA15__GPIO2_IO15 0x14 /* SODIMM 107 */
+ MX7D_PAD_EPDC_DATA10__GPIO2_IO10 0x74 /* SODIMM 105 */
+ MX7D_PAD_EPDC_DATA15__GPIO2_IO15 0x74 /* SODIMM 107 */
MX7D_PAD_EPDC_DATA00__GPIO2_IO0 0x14 /* SODIMM 111 */
MX7D_PAD_EPDC_DATA01__GPIO2_IO1 0x14 /* SODIMM 113 */
MX7D_PAD_EPDC_DATA02__GPIO2_IO2 0x14 /* SODIMM 115 */
@@ -333,7 +333,7 @@
MX7D_PAD_SD2_DATA2__GPIO5_IO16 0x14 /* SODIMM 100 */
MX7D_PAD_SD2_DATA3__GPIO5_IO17 0x14 /* SODIMM 102 */
MX7D_PAD_EPDC_GDSP__GPIO2_IO27 0x14 /* SODIMM 104 */
- MX7D_PAD_EPDC_BDR0__GPIO2_IO28 0x14 /* SODIMM 106 */
+ MX7D_PAD_EPDC_BDR0__GPIO2_IO28 0x74 /* SODIMM 106 */
MX7D_PAD_EPDC_BDR1__GPIO2_IO29 0x14 /* SODIMM 110 */
MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 0x14 /* SODIMM 112 */
MX7D_PAD_EPDC_SDCLK__GPIO2_IO16 0x14 /* SODIMM 114 */
@@ -357,7 +357,7 @@
pinctrl_gpio2: gpio2-grp { /* On X22 Camera interface */
fsl,pins = <
MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 0x14 /* SODIMM 65 */
- MX7D_PAD_SD1_CD_B__GPIO5_IO0 0x14 /* SODIMM 69 */
+ MX7D_PAD_SD1_CD_B__GPIO5_IO0 0x74 /* SODIMM 69 */
MX7D_PAD_SD1_WP__GPIO5_IO1 0x14 /* SODIMM 71 */
MX7D_PAD_I2C4_SDA__GPIO4_IO15 0x14 /* SODIMM 75 */
MX7D_PAD_ECSPI1_MISO__GPIO4_IO18 0x14 /* SODIMM 79 */
@@ -378,8 +378,8 @@
MX7D_PAD_LCD_DATA19__GPIO3_IO24 0x14 /* SODIMM 138 */
MX7D_PAD_LCD_DATA20__GPIO3_IO25 0x14 /* SODIMM 140 */
MX7D_PAD_LCD_DATA21__GPIO3_IO26 0x14 /* SODIMM 142 */
- MX7D_PAD_LCD_DATA22__GPIO3_IO27 0x14 /* SODIMM 146 */
- MX7D_PAD_LCD_DATA23__GPIO3_IO28 0x14 /* SODIMM 148 */
+ MX7D_PAD_LCD_DATA22__GPIO3_IO27 0x74 /* SODIMM 144 */
+ MX7D_PAD_LCD_DATA23__GPIO3_IO28 0x74 /* SODIMM 146 */
>;
};
--
2.15.1
next prev parent reply other threads:[~2017-12-06 15:29 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-06 15:29 [PATCH 1/9] ARM: dts: imx7-colibri: move and rename USB Host power regulator Stefan Agner
2017-12-06 15:29 ` [PATCH 2/9] ARM: dts: imx7-colibri: make sure multiplexed pins are not active Stefan Agner
[not found] ` <20171206153005.6144-2-stefan-XLVq0VzYD2Y@public.gmane.org>
2017-12-16 14:01 ` Fabio Estevam
[not found] ` <CAOMZO5AD6bDEMStEWY8hRG_8gh0RAD_66zboTsKd-cFkPtiLKg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-12-17 20:02 ` Stefan Agner
2017-12-06 15:29 ` Stefan Agner [this message]
[not found] ` <20171206153005.6144-3-stefan-XLVq0VzYD2Y@public.gmane.org>
2017-12-16 14:02 ` [PATCH 3/9] ARM: dts: imx7-colibri: mux pull-ups where appropriate Fabio Estevam
2017-12-06 15:30 ` [PATCH 4/9] ARM: dts: imx7-colibri: use NAND_CE1 as GPIO Stefan Agner
[not found] ` <20171206153005.6144-4-stefan-XLVq0VzYD2Y@public.gmane.org>
2017-12-16 14:02 ` Fabio Estevam
2017-12-06 15:30 ` [PATCH 5/9] ARM: dts: imx7-colibri: specify cpu-supply Stefan Agner
[not found] ` <20171206153005.6144-5-stefan-XLVq0VzYD2Y@public.gmane.org>
2017-12-16 13:59 ` Fabio Estevam
2017-12-06 15:30 ` [PATCH 7/9] ARM: dts: imx7-colibri: specify backlight GPIO Stefan Agner
[not found] ` <20171206153005.6144-7-stefan-XLVq0VzYD2Y@public.gmane.org>
2017-12-16 14:03 ` Fabio Estevam
2017-12-06 15:30 ` [PATCH 8/9] ARM: dts: imx7-colibri: add MCP2515 CAN controller Stefan Agner
2017-12-07 8:59 ` Stefan Agner
[not found] ` <20171206153005.6144-8-stefan-XLVq0VzYD2Y@public.gmane.org>
2017-12-16 14:05 ` Fabio Estevam
2017-12-06 15:30 ` [PATCH 9/9] ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support Stefan Agner
[not found] ` <20171206153005.6144-9-stefan-XLVq0VzYD2Y@public.gmane.org>
2017-12-16 14:09 ` Fabio Estevam
[not found] ` <CAOMZO5Dv5dRbbHeqMtitXaHjJbMF4nGQWg0dpyHu0hh+2TaxGA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-12-16 14:18 ` Philippe Ombredanne
[not found] ` <20171206153005.6144-1-stefan-XLVq0VzYD2Y@public.gmane.org>
2017-12-06 15:30 ` [PATCH 6/9] ARM: dts: imx7-colibri: specify usdhc1 supplies Stefan Agner
[not found] ` <20171206153005.6144-6-stefan-XLVq0VzYD2Y@public.gmane.org>
2017-12-16 14:03 ` Fabio Estevam
2017-12-16 14:00 ` [PATCH 1/9] ARM: dts: imx7-colibri: move and rename USB Host power regulator Fabio Estevam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171206153005.6144-3-stefan@agner.ch \
--to=stefan@agner.ch \
--cc=devicetree@vger.kernel.org \
--cc=fabio.estevam@nxp.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).