From: Adrian Fiergolski <adrian.fiergolski@cern.ch>
To: linux-i2c@vger.kernel.org
Cc: peda@axentia.se, devicetree@vger.kernel.org, robh+dt@kernel.org,
Adrian Fiergolski <adrian.fiergolski@cern.ch>
Subject: [PATCH v6] i2c: Add support for NXP PCA984x family.
Date: Mon, 18 Dec 2017 18:45:06 +0100 [thread overview]
Message-ID: <20171218174506.20543-1-adrian.fiergolski@cern.ch> (raw)
In-Reply-To: <07bf7aae-59ab-cb2b-dcb0-95ec2de66633@axentia.se>
This patch extends the current i2c-mux-pca954x driver and adds support for
a newer PCA984x family of the I2C switches and multiplexers from NXP.
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@cern.ch>
---
.../devicetree/bindings/i2c/i2c-mux-pca954x.txt | 5 ++-
drivers/i2c/muxes/Kconfig | 6 ++--
drivers/i2c/muxes/i2c-mux-pca954x.c | 38 +++++++++++++++++++---
3 files changed, 41 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
index aa097045a10e..b428bc0d81b1 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
@@ -1,10 +1,13 @@
* NXP PCA954x I2C bus switch
+The driver supports NXP PCA954x and PCA984x I2C mux/switch devices.
+
Required Properties:
- compatible: Must contain one of the following.
"nxp,pca9540", "nxp,pca9542", "nxp,pca9543", "nxp,pca9544",
- "nxp,pca9545", "nxp,pca9546", "nxp,pca9547", "nxp,pca9548"
+ "nxp,pca9545", "nxp,pca9546", "nxp,pca9547", "nxp,pca9548",
+ "nxp,pca9846", "nxp,pca9847", "nxp,pca9848", "nxp,pca9849"
- reg: The I2C address of the device.
diff --git a/drivers/i2c/muxes/Kconfig b/drivers/i2c/muxes/Kconfig
index 0f5c8fc36625..52a4a922e7e6 100644
--- a/drivers/i2c/muxes/Kconfig
+++ b/drivers/i2c/muxes/Kconfig
@@ -64,11 +64,11 @@ config I2C_MUX_PCA9541
will be called i2c-mux-pca9541.
config I2C_MUX_PCA954x
- tristate "Philips PCA954x I2C Mux/switches"
+ tristate "NXP PCA954x and PCA984x I2C Mux/switches"
depends on GPIOLIB || COMPILE_TEST
help
- If you say yes here you get support for the Philips PCA954x
- I2C mux/switch devices.
+ If you say yes here you get support for the NXP PCA954x
+ and PCA984x I2C mux/switch devices.
This driver can also be built as a module. If so, the module
will be called i2c-mux-pca954x.
diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c b/drivers/i2c/muxes/i2c-mux-pca954x.c
index 2ca068d8b92d..fbb84c7ef282 100644
--- a/drivers/i2c/muxes/i2c-mux-pca954x.c
+++ b/drivers/i2c/muxes/i2c-mux-pca954x.c
@@ -4,11 +4,11 @@
* Copyright (c) 2008-2009 Rodolfo Giometti <giometti@linux.it>
* Copyright (c) 2008-2009 Eurotech S.p.A. <info@eurotech.it>
*
- * This module supports the PCA954x series of I2C multiplexer/switch chips
- * made by Philips Semiconductors.
+ * This module supports the PCA954x and PCA954x series of I2C multiplexer/switch
+ * chips made by NXP Semiconductors.
* This includes the:
- * PCA9540, PCA9542, PCA9543, PCA9544, PCA9545, PCA9546, PCA9547
- * and PCA9548.
+ * PCA9540, PCA9542, PCA9543, PCA9544, PCA9545, PCA9546, PCA9547,
+ * PCA9548, PCA9846, PCA9847, PCA9848 and PCA9849.
*
* These chips are all controlled via the I2C bus itself, and all have a
* single 8-bit register. The upstream "parent" bus fans out to two,
@@ -63,6 +63,10 @@ enum pca_type {
pca_9546,
pca_9547,
pca_9548,
+ pca_9846,
+ pca_9847,
+ pca_9848,
+ pca_9849,
};
struct chip_desc {
@@ -129,6 +133,24 @@ static const struct chip_desc chips[] = {
.nchans = 8,
.muxtype = pca954x_isswi,
},
+ [pca_9846] = {
+ .nchans = 4,
+ .muxtype = pca954x_isswi,
+ },
+ [pca_9847] = {
+ .nchans = 8,
+ .enable = 0x8,
+ .muxtype = pca954x_ismux,
+ },
+ [pca_9848] = {
+ .nchans = 8,
+ .muxtype = pca954x_isswi,
+ },
+ [pca_9849] = {
+ .nchans = 4,
+ .enable = 0x4,
+ .muxtype = pca954x_ismux,
+ },
};
static const struct i2c_device_id pca954x_id[] = {
@@ -140,6 +162,10 @@ static const struct i2c_device_id pca954x_id[] = {
{ "pca9546", pca_9546 },
{ "pca9547", pca_9547 },
{ "pca9548", pca_9548 },
+ { "pca9846", pca_9846 },
+ { "pca9847", pca_9847 },
+ { "pca9848", pca_9848 },
+ { "pca9849", pca_9849 },
{ }
};
MODULE_DEVICE_TABLE(i2c, pca954x_id);
@@ -154,6 +180,10 @@ static const struct of_device_id pca954x_of_match[] = {
{ .compatible = "nxp,pca9546", .data = &chips[pca_9546] },
{ .compatible = "nxp,pca9547", .data = &chips[pca_9547] },
{ .compatible = "nxp,pca9548", .data = &chips[pca_9548] },
+ { .compatible = "nxp,pca9846", .data = &chips[pca_9846] },
+ { .compatible = "nxp,pca9847", .data = &chips[pca_9847] },
+ { .compatible = "nxp,pca9848", .data = &chips[pca_9848] },
+ { .compatible = "nxp,pca9849", .data = &chips[pca_9849] },
{}
};
MODULE_DEVICE_TABLE(of, pca954x_of_match);
--
2.14.1
next prev parent reply other threads:[~2017-12-18 17:45 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <5cbfd97a-146b-8851-c63a-f2f60da33f5b@axentia.se>
[not found] ` <20171213161223.23832-1-adrian.fiergolski@cern.ch>
[not found] ` <706ae942-a228-32d1-60d9-51c467d36188@axentia.se>
2017-12-14 9:54 ` [PATCH v4] i2c: Add support for NXP PCA984x family Peter Rosin
[not found] ` <990e4a1f-a9ac-c899-0075-ae3211ff9475-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
2017-12-14 11:20 ` [PATCH v5] " Adrian Fiergolski
[not found] ` <20171214112003.13701-1-adrian.fiergolski-vJEk5272eHo@public.gmane.org>
2017-12-14 21:22 ` Peter Rosin
2017-12-18 17:45 ` Adrian Fiergolski [this message]
2017-12-20 18:27 ` [PATCH v6] " Rob Herring
2017-12-25 21:26 ` [PATCH v7] " Adrian Fiergolski
[not found] ` <20171225212646.8062-1-adrian.fiergolski-vJEk5272eHo@public.gmane.org>
2017-12-26 17:58 ` Rob Herring
2017-12-28 23:31 ` Peter Rosin
2017-12-15 10:40 ` [PATCH v5] " Peter Rosin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171218174506.20543-1-adrian.fiergolski@cern.ch \
--to=adrian.fiergolski@cern.ch \
--cc=devicetree@vger.kernel.org \
--cc=linux-i2c@vger.kernel.org \
--cc=peda@axentia.se \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).