devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Jonathan Cameron <jic23@kernel.org>
To: Philipp Rossak <embed3d@gmail.com>
Cc: lee.jones@linaro.org, robh+dt@kernel.org, mark.rutland@arm.com,
	maxime.ripard@free-electrons.com, wens@csie.org,
	linux@armlinux.org.uk, knaack.h@gmx.de, lars@metafoo.de,
	pmeerw@pmeerw.net, davem@davemloft.net, hans.verkuil@cisco.com,
	mchehab@kernel.org, rask@formelder.dk, clabbe.montjoie@gmail.com,
	sean@mess.org, krzk@kernel.org,
	quentin.schulz@free-electrons.com, icenowy@aosc.io,
	edu.molinas@gmail.com, singhalsimran0@gmail.com,
	linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com
Subject: Re: [PATCH 04/16] iio: adc: sun4i-gpadc-iio: rework: sampling start/end code readout reg
Date: Sun, 28 Jan 2018 08:43:59 +0000	[thread overview]
Message-ID: <20180128084359.3f3e523c@archlinux> (raw)
In-Reply-To: <20180126151941.12183-5-embed3d@gmail.com>

On Fri, 26 Jan 2018 16:19:29 +0100
Philipp Rossak <embed3d@gmail.com> wrote:

> For adding newer sensor some basic rework of the code is necessary.
> 
> This commit reworks the code and allows the sampling start/end code and
> the position of value readout register to be altered. Later the start/end
> functions will be used to configure the ths and start/stop the
> sampling.
> 
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Hmm. It almost always turns out to be a bad idea to assume a particular
set of registers will be consistent across a hardware family.  Usual convention
is just to prefix them with the first supported device and use them across
the variants where they are correct.  I.e. don't use wild cards or generic
names as they often end up implying a wider range of applicability than
we want.

A few other comments inline.  Reworking code to make it ready for later
patches is fine, but this also adds a lot of new code which isn't used until
much later in the series.  Move it there...
> ---
>  drivers/iio/adc/sun4i-gpadc-iio.c | 87 +++++++++++++++++++++++++++++++++++----
>  include/linux/mfd/sun4i-gpadc.h   | 19 +++++++--
>  2 files changed, 94 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/iio/adc/sun4i-gpadc-iio.c b/drivers/iio/adc/sun4i-gpadc-iio.c
> index 03804ff9c006..363936b37c5a 100644
> --- a/drivers/iio/adc/sun4i-gpadc-iio.c
> +++ b/drivers/iio/adc/sun4i-gpadc-iio.c
> @@ -49,6 +49,18 @@ static unsigned int sun6i_gpadc_chan_select(unsigned int chan)
>  	return SUN6I_GPADC_CTRL1_ADC_CHAN_SELECT(chan);
>  }
>  
> +struct sun4i_gpadc_iio;
> +
> +/*
> + * Prototypes for these functions, which enable these functions to be
> + * referenced in gpadc_data structures.
> + */
> +static int sun4i_gpadc_sample_start(struct sun4i_gpadc_iio *info);
> +static int sun4i_gpadc_sample_end(struct sun4i_gpadc_iio *info);
> +
> +static int sunxi_ths_sample_start(struct sun4i_gpadc_iio *info);

Superficially this appears to be introduced but not used... Patch 9
is first to use it I think?  Introduce it then rather than here.

> +static int sunxi_ths_sample_end(struct sun4i_gpadc_iio *info);
> +
>  struct gpadc_data {
>  	int		temp_offset;
>  	int		temp_scale;
> @@ -56,6 +68,13 @@ struct gpadc_data {
>  	unsigned int	tp_adc_select;
>  	unsigned int	(*adc_chan_select)(unsigned int chan);
>  	unsigned int	adc_chan_mask;
> +	unsigned int	temp_data;
> +	int		(*sample_start)(struct sun4i_gpadc_iio *info);
> +	int		(*sample_end)(struct sun4i_gpadc_iio *info);
> +	u32		ctrl0_map;
> +	u32		ctrl2_map;
> +	u32		sensor_en_map;
> +	u32		filter_map;
>  };
>  
>  static const struct gpadc_data sun4i_gpadc_data = {
> @@ -65,6 +84,9 @@ static const struct gpadc_data sun4i_gpadc_data = {
>  	.tp_adc_select = SUN4I_GPADC_CTRL1_TP_ADC_SELECT,
>  	.adc_chan_select = &sun4i_gpadc_chan_select,
>  	.adc_chan_mask = SUN4I_GPADC_CTRL1_ADC_CHAN_MASK,
> +	.temp_data = SUN4I_GPADC_TEMP_DATA,
> +	.sample_start = sun4i_gpadc_sample_start,
> +	.sample_end = sun4i_gpadc_sample_end,
>  };
>  
>  static const struct gpadc_data sun5i_gpadc_data = {
> @@ -74,6 +96,9 @@ static const struct gpadc_data sun5i_gpadc_data = {
>  	.tp_adc_select = SUN4I_GPADC_CTRL1_TP_ADC_SELECT,
>  	.adc_chan_select = &sun4i_gpadc_chan_select,
>  	.adc_chan_mask = SUN4I_GPADC_CTRL1_ADC_CHAN_MASK,
> +	.temp_data = SUN4I_GPADC_TEMP_DATA,
> +	.sample_start = sun4i_gpadc_sample_start,
> +	.sample_end = sun4i_gpadc_sample_end,
>  };
>  
>  static const struct gpadc_data sun6i_gpadc_data = {
> @@ -83,12 +108,18 @@ static const struct gpadc_data sun6i_gpadc_data = {
>  	.tp_adc_select = SUN6I_GPADC_CTRL1_TP_ADC_SELECT,
>  	.adc_chan_select = &sun6i_gpadc_chan_select,
>  	.adc_chan_mask = SUN6I_GPADC_CTRL1_ADC_CHAN_MASK,
> +	.temp_data = SUN4I_GPADC_TEMP_DATA,
> +	.sample_start = sun4i_gpadc_sample_start,
> +	.sample_end = sun4i_gpadc_sample_end,
>  };
>  
>  static const struct gpadc_data sun8i_a33_gpadc_data = {
>  	.temp_offset = -1662,
>  	.temp_scale = 162,
>  	.tp_mode_en = SUN8I_A33_GPADC_CTRL1_CHOP_TEMP_EN,
> +	.temp_data = SUN4I_GPADC_TEMP_DATA,
> +	.sample_start = sun4i_gpadc_sample_start,
> +	.sample_end = sun4i_gpadc_sample_end,
>  };
>  
>  struct sun4i_gpadc_iio {
> @@ -277,7 +308,7 @@ static int sun4i_gpadc_temp_read(struct iio_dev *indio_dev, int *val)
>  	if (info->no_irq) {
>  		pm_runtime_get_sync(indio_dev->dev.parent);
>  
> -		regmap_read(info->regmap, SUN4I_GPADC_TEMP_DATA, val);
> +		regmap_read(info->regmap, info->data->temp_data, val);
>  
>  		pm_runtime_mark_last_busy(indio_dev->dev.parent);
>  		pm_runtime_put_autosuspend(indio_dev->dev.parent);
> @@ -382,10 +413,8 @@ static irqreturn_t sun4i_gpadc_fifo_data_irq_handler(int irq, void *dev_id)
>  	return IRQ_HANDLED;
>  }
>  
> -static int sun4i_gpadc_runtime_suspend(struct device *dev)
> +static int sun4i_gpadc_sample_end(struct sun4i_gpadc_iio *info)
>  {
> -	struct sun4i_gpadc_iio *info = iio_priv(dev_get_drvdata(dev));
> -
>  	/* Disable the ADC on IP */
>  	regmap_write(info->regmap, SUN4I_GPADC_CTRL1, 0);
>  	/* Disable temperature sensor on IP */
> @@ -394,19 +423,32 @@ static int sun4i_gpadc_runtime_suspend(struct device *dev)
>  	return 0;
>  }
>  
> -static int sun4i_gpadc_runtime_resume(struct device *dev)
> +static int sunxi_ths_sample_end(struct sun4i_gpadc_iio *info)
> +{
> +	/* Disable temperature sensor */
> +	regmap_write(info->regmap, SUNXI_THS_CTRL2, 0x0);
> +
> +	return 0;
> +}
> +
> +static int sun4i_gpadc_runtime_suspend(struct device *dev)
>  {
>  	struct sun4i_gpadc_iio *info = iio_priv(dev_get_drvdata(dev));
>  
> +	return info->data->sample_end(info);
> +}
> +
> +static int sun4i_gpadc_sample_start(struct sun4i_gpadc_iio *info)
> +{
>  	/* clkin = 6MHz */
>  	regmap_write(info->regmap, SUN4I_GPADC_CTRL0,
>  		     SUN4I_GPADC_CTRL0_ADC_CLK_DIVIDER(2) |
>  		     SUN4I_GPADC_CTRL0_FS_DIV(7) |
> -		     SUN4I_GPADC_CTRL0_T_ACQ(63));
> +		     SUNXI_THS_ACQ0(63));
>  	regmap_write(info->regmap, SUN4I_GPADC_CTRL1, info->data->tp_mode_en);
>  	regmap_write(info->regmap, SUN4I_GPADC_CTRL3,
> -		     SUN4I_GPADC_CTRL3_FILTER_EN |
> -		     SUN4I_GPADC_CTRL3_FILTER_TYPE(1));
> +		     SUNXI_THS_FILTER_EN |
> +		     SUNXI_THS_FILTER_TYPE(1));

Why if these are temperature sensor features are we setting them in the
general purpose ADC start function?

>  	/* period = SUN4I_GPADC_TPR_TEMP_PERIOD * 256 * 16 / clkin; ~0.6s */
>  	regmap_write(info->regmap, SUN4I_GPADC_TPR,
>  		     SUN4I_GPADC_TPR_TEMP_ENABLE |
> @@ -415,6 +457,35 @@ static int sun4i_gpadc_runtime_resume(struct device *dev)
>  	return 0;
>  }
>  
> +static int sunxi_ths_sample_start(struct sun4i_gpadc_iio *info)
> +{
> +	u32 value;
> +
> +	if (info->data->ctrl0_map)
> +		regmap_write(info->regmap, SUNXI_THS_CTRL0,
> +			info->data->ctrl0_map);
> +
> +	regmap_write(info->regmap, SUNXI_THS_CTRL2,
> +		info->data->ctrl2_map);
> +
> +	regmap_write(info->regmap, SUNXI_THS_FILTER,
> +		info->data->filter_map);
> +
> +	regmap_read(info->regmap, SUNXI_THS_CTRL2, &value);
> +
> +	regmap_write(info->regmap, SUNXI_THS_CTRL2,
> +		info->data->sensor_en_map | value);
> +
> +	return 0;
> +}
> +
> +static int sun4i_gpadc_runtime_resume(struct device *dev)
> +{
> +	struct sun4i_gpadc_iio *info = iio_priv(dev_get_drvdata(dev));
> +
> +	return info->data->sample_start(info);
> +}
> +
>  static int sun4i_gpadc_get_temp(void *data, int *temp)
>  {
>  	struct sun4i_gpadc_iio *info = data;
> diff --git a/include/linux/mfd/sun4i-gpadc.h b/include/linux/mfd/sun4i-gpadc.h
> index 78d31984a222..39e096c3ddac 100644
> --- a/include/linux/mfd/sun4i-gpadc.h
> +++ b/include/linux/mfd/sun4i-gpadc.h
> @@ -17,7 +17,6 @@
>  #define SUN4I_GPADC_CTRL0_ADC_CLK_SELECT		BIT(22)
>  #define SUN4I_GPADC_CTRL0_ADC_CLK_DIVIDER(x)		((GENMASK(1, 0) & (x)) << 20)
>  #define SUN4I_GPADC_CTRL0_FS_DIV(x)			((GENMASK(3, 0) & (x)) << 16)
> -#define SUN4I_GPADC_CTRL0_T_ACQ(x)			(GENMASK(15, 0) & (x))
>  
>  #define SUN4I_GPADC_CTRL1				0x04
>  
> @@ -51,9 +50,6 @@
>  
>  #define SUN4I_GPADC_CTRL3				0x0c
>  
> -#define SUN4I_GPADC_CTRL3_FILTER_EN			BIT(2)
> -#define SUN4I_GPADC_CTRL3_FILTER_TYPE(x)		(GENMASK(1, 0) & (x))
> -
>  #define SUN4I_GPADC_TPR					0x18
>  
>  #define SUN4I_GPADC_TPR_TEMP_ENABLE			BIT(16)
> @@ -90,6 +86,21 @@
>  /* 10s delay before suspending the IP */
>  #define SUN4I_GPADC_AUTOSUSPEND_DELAY			10000
>  
> +/* SUNXI_THS COMMON REGISTERS + DEFINES */
> +#define SUNXI_THS_CTRL0					0x00
> +#define SUNXI_THS_CTRL2					0x40
> +#define SUNXI_THS_FILTER				0x70
> +
> +#define SUNXI_THS_FILTER_EN				BIT(2)
> +#define SUNXI_THS_FILTER_TYPE(x)			(GENMASK(1, 0) & (x))
> +#define SUNXI_THS_ACQ0(x)				(GENMASK(15, 0) & (x))
> +#define SUNXI_THS_ACQ1(x)				(GENMASK(31, 16) & ((x) << 16))
> +
> +#define SUNXI_THS_TEMP_SENSE_EN0			BIT(0)
> +#define SUNXI_THS_TEMP_SENSE_EN1			BIT(1)
> +#define SUNXI_THS_TEMP_SENSE_EN2			BIT(2)
> +#define SUNXI_THS_TEMP_SENSE_EN3			BIT(3)
> +
>  struct sun4i_gpadc_dev {
>  	struct device			*dev;
>  	struct regmap			*regmap;

  reply	other threads:[~2018-01-28  8:43 UTC|newest]

Thread overview: 38+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-01-26 15:19 [PATCH 00/16] IIO-based thermal sensor driver for Allwinner H3 and A83T SoC Philipp Rossak
     [not found] ` <20180126151941.12183-1-embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-01-26 15:19   ` [PATCH 01/16] dt-bindings: update the Allwinner GPADC device tree binding for H3 & A83T Philipp Rossak
2018-01-26 15:19   ` [PATCH 02/16] arm: config: sunxi_defconfig: enable SUN4I_GPADC Philipp Rossak
2018-01-26 15:19   ` [PATCH 03/16] iio: adc: sun4i-gpadc-iio: rename A33-specified registers to contain A33 Philipp Rossak
     [not found]     ` <20180126151941.12183-4-embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-01-28  8:34       ` Jonathan Cameron
2018-01-26 15:19   ` [PATCH 04/16] iio: adc: sun4i-gpadc-iio: rework: sampling start/end code readout reg Philipp Rossak
2018-01-28  8:43     ` Jonathan Cameron [this message]
2018-01-28 13:34       ` Philipp Rossak
2018-01-28 13:37         ` Icenowy Zheng
     [not found]           ` <2CC367BA-766A-4384-82EE-9A38BBFB08C2-h8G6r0blFSE@public.gmane.org>
2018-01-28 14:32             ` Philipp Rossak
2018-01-26 15:19   ` [PATCH 05/16] iio: adc: sun4i-gpadc-iio: rework: support clocks and reset Philipp Rossak
2018-01-28  8:50     ` Jonathan Cameron
2018-01-28 11:34       ` Philipp Rossak
2018-01-26 15:19   ` [PATCH 06/16] iio: adc: sun4i-gpadc-iio: rework: support multible sensors Philipp Rossak
2018-01-28  9:08     ` Jonathan Cameron
2018-01-28 14:10       ` Philipp Rossak
2018-01-26 15:19   ` [PATCH 07/16] iio: adc: sun4i-gpadc-iio: rework: support nvmem calibration data Philipp Rossak
2018-01-28  9:02     ` Jonathan Cameron
2018-01-28 13:46       ` Philipp Rossak
     [not found]         ` <6ebbb5e0-eb5f-afe4-50e8-eb3cee8ec7fa-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-01-28 13:52           ` Icenowy Zheng
     [not found]             ` <1927F24D-D3ED-49CF-9B7C-A7C8C873F0CF-h8G6r0blFSE@public.gmane.org>
2018-01-28 14:39               ` Philipp Rossak
2018-01-26 15:19   ` [PATCH 08/16] iio: adc: sun4i-gpadc-iio: rework: add interrupt support Philipp Rossak
     [not found]     ` <20180126151941.12183-9-embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-01-28  9:06       ` Jonathan Cameron
2018-01-28 13:48         ` Philipp Rossak
2018-01-26 15:19   ` [PATCH 09/16] iio: adc: sun4i-gpadc-iio: add support for H3 thermal sensor Philipp Rossak
2018-01-26 15:19   ` [PATCH 10/16] iio: adc: sun4i-gpadc-iio: add support for A83T " Philipp Rossak
     [not found]     ` <20180126151941.12183-11-embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-01-26 17:46       ` [linux-sunxi] " Ondřej Jirman
     [not found]         ` <20180126174602.qolcswhqblgmlad7-9v8tmBix7cb9zxVx7UNMDg@public.gmane.org>
2018-01-27  4:30           ` Philipp Rossak
2018-01-26 15:19   ` [PATCH 11/16] arm: dts: sunxi-h3-h5: add support for the thermal sensor in H3 and H5 Philipp Rossak
2018-01-26 15:19   ` [PATCH 12/16] arm: dts: sun8i: h3: add support for the thermal sensor in H3 Philipp Rossak
2018-01-26 15:19   ` [PATCH 13/16] arm: dts: sun8i: h3: add thermal zone to H3 Philipp Rossak
     [not found]     ` <20180126151941.12183-14-embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-01-26 16:26       ` Samuel Holland
     [not found]         ` <4cfb1faf-a712-c882-1ef1-55845c1bb00e-RkNLwX/CsU9g9hUCZPvPmw@public.gmane.org>
2018-01-26 17:48           ` [linux-sunxi] " Philipp Rossak
2018-01-26 15:19   ` [PATCH 14/16] arm: dts: sun8i: h3: enable H3 sid controller Philipp Rossak
2018-01-26 15:19   ` [PATCH 15/16] arm: dts: sun8i: a83t: add support for the thermal sensor in A83T Philipp Rossak
2018-01-26 15:19   ` [PATCH 16/16] arm: dts: sun8i: a83t: add thermal zone to A83T Philipp Rossak
     [not found]     ` <20180126151941.12183-17-embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-01-26 16:25       ` Samuel Holland
2018-01-26 17:35         ` [linux-sunxi] " Philipp Rossak

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180128084359.3f3e523c@archlinux \
    --to=jic23@kernel.org \
    --cc=clabbe.montjoie@gmail.com \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=edu.molinas@gmail.com \
    --cc=embed3d@gmail.com \
    --cc=hans.verkuil@cisco.com \
    --cc=icenowy@aosc.io \
    --cc=knaack.h@gmx.de \
    --cc=krzk@kernel.org \
    --cc=lars@metafoo.de \
    --cc=lee.jones@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-iio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-sunxi@googlegroups.com \
    --cc=linux@armlinux.org.uk \
    --cc=mark.rutland@arm.com \
    --cc=maxime.ripard@free-electrons.com \
    --cc=mchehab@kernel.org \
    --cc=pmeerw@pmeerw.net \
    --cc=quentin.schulz@free-electrons.com \
    --cc=rask@formelder.dk \
    --cc=robh+dt@kernel.org \
    --cc=sean@mess.org \
    --cc=singhalsimran0@gmail.com \
    --cc=wens@csie.org \
    --subject='Re: [PATCH 04/16] iio: adc: sun4i-gpadc-iio: rework: sampling start/end code readout reg' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).