From mboxrd@z Thu Jan 1 00:00:00 1970 From: Jonathan Cameron Subject: Re: [PATCH 04/16] iio: adc: sun4i-gpadc-iio: rework: sampling start/end code readout reg Date: Sun, 28 Jan 2018 08:43:59 +0000 Message-ID: <20180128084359.3f3e523c@archlinux> References: <20180126151941.12183-1-embed3d@gmail.com> <20180126151941.12183-5-embed3d@gmail.com> Mime-Version: 1.0 Content-Type: text/plain; charset=US-ASCII Content-Transfer-Encoding: 7bit Return-path: In-Reply-To: <20180126151941.12183-5-embed3d@gmail.com> Sender: linux-kernel-owner@vger.kernel.org To: Philipp Rossak Cc: lee.jones@linaro.org, robh+dt@kernel.org, mark.rutland@arm.com, maxime.ripard@free-electrons.com, wens@csie.org, linux@armlinux.org.uk, knaack.h@gmx.de, lars@metafoo.de, pmeerw@pmeerw.net, davem@davemloft.net, hans.verkuil@cisco.com, mchehab@kernel.org, rask@formelder.dk, clabbe.montjoie@gmail.com, sean@mess.org, krzk@kernel.org, quentin.schulz@free-electrons.com, icenowy@aosc.io, edu.molinas@gmail.com, singhalsimran0@gmail.com, linux-iio@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com List-Id: devicetree@vger.kernel.org On Fri, 26 Jan 2018 16:19:29 +0100 Philipp Rossak wrote: > For adding newer sensor some basic rework of the code is necessary. > > This commit reworks the code and allows the sampling start/end code and > the position of value readout register to be altered. Later the start/end > functions will be used to configure the ths and start/stop the > sampling. > > Signed-off-by: Icenowy Zheng > Signed-off-by: Philipp Rossak Hmm. It almost always turns out to be a bad idea to assume a particular set of registers will be consistent across a hardware family. Usual convention is just to prefix them with the first supported device and use them across the variants where they are correct. I.e. don't use wild cards or generic names as they often end up implying a wider range of applicability than we want. A few other comments inline. Reworking code to make it ready for later patches is fine, but this also adds a lot of new code which isn't used until much later in the series. Move it there... > --- > drivers/iio/adc/sun4i-gpadc-iio.c | 87 +++++++++++++++++++++++++++++++++++---- > include/linux/mfd/sun4i-gpadc.h | 19 +++++++-- > 2 files changed, 94 insertions(+), 12 deletions(-) > > diff --git a/drivers/iio/adc/sun4i-gpadc-iio.c b/drivers/iio/adc/sun4i-gpadc-iio.c > index 03804ff9c006..363936b37c5a 100644 > --- a/drivers/iio/adc/sun4i-gpadc-iio.c > +++ b/drivers/iio/adc/sun4i-gpadc-iio.c > @@ -49,6 +49,18 @@ static unsigned int sun6i_gpadc_chan_select(unsigned int chan) > return SUN6I_GPADC_CTRL1_ADC_CHAN_SELECT(chan); > } > > +struct sun4i_gpadc_iio; > + > +/* > + * Prototypes for these functions, which enable these functions to be > + * referenced in gpadc_data structures. > + */ > +static int sun4i_gpadc_sample_start(struct sun4i_gpadc_iio *info); > +static int sun4i_gpadc_sample_end(struct sun4i_gpadc_iio *info); > + > +static int sunxi_ths_sample_start(struct sun4i_gpadc_iio *info); Superficially this appears to be introduced but not used... Patch 9 is first to use it I think? Introduce it then rather than here. > +static int sunxi_ths_sample_end(struct sun4i_gpadc_iio *info); > + > struct gpadc_data { > int temp_offset; > int temp_scale; > @@ -56,6 +68,13 @@ struct gpadc_data { > unsigned int tp_adc_select; > unsigned int (*adc_chan_select)(unsigned int chan); > unsigned int adc_chan_mask; > + unsigned int temp_data; > + int (*sample_start)(struct sun4i_gpadc_iio *info); > + int (*sample_end)(struct sun4i_gpadc_iio *info); > + u32 ctrl0_map; > + u32 ctrl2_map; > + u32 sensor_en_map; > + u32 filter_map; > }; > > static const struct gpadc_data sun4i_gpadc_data = { > @@ -65,6 +84,9 @@ static const struct gpadc_data sun4i_gpadc_data = { > .tp_adc_select = SUN4I_GPADC_CTRL1_TP_ADC_SELECT, > .adc_chan_select = &sun4i_gpadc_chan_select, > .adc_chan_mask = SUN4I_GPADC_CTRL1_ADC_CHAN_MASK, > + .temp_data = SUN4I_GPADC_TEMP_DATA, > + .sample_start = sun4i_gpadc_sample_start, > + .sample_end = sun4i_gpadc_sample_end, > }; > > static const struct gpadc_data sun5i_gpadc_data = { > @@ -74,6 +96,9 @@ static const struct gpadc_data sun5i_gpadc_data = { > .tp_adc_select = SUN4I_GPADC_CTRL1_TP_ADC_SELECT, > .adc_chan_select = &sun4i_gpadc_chan_select, > .adc_chan_mask = SUN4I_GPADC_CTRL1_ADC_CHAN_MASK, > + .temp_data = SUN4I_GPADC_TEMP_DATA, > + .sample_start = sun4i_gpadc_sample_start, > + .sample_end = sun4i_gpadc_sample_end, > }; > > static const struct gpadc_data sun6i_gpadc_data = { > @@ -83,12 +108,18 @@ static const struct gpadc_data sun6i_gpadc_data = { > .tp_adc_select = SUN6I_GPADC_CTRL1_TP_ADC_SELECT, > .adc_chan_select = &sun6i_gpadc_chan_select, > .adc_chan_mask = SUN6I_GPADC_CTRL1_ADC_CHAN_MASK, > + .temp_data = SUN4I_GPADC_TEMP_DATA, > + .sample_start = sun4i_gpadc_sample_start, > + .sample_end = sun4i_gpadc_sample_end, > }; > > static const struct gpadc_data sun8i_a33_gpadc_data = { > .temp_offset = -1662, > .temp_scale = 162, > .tp_mode_en = SUN8I_A33_GPADC_CTRL1_CHOP_TEMP_EN, > + .temp_data = SUN4I_GPADC_TEMP_DATA, > + .sample_start = sun4i_gpadc_sample_start, > + .sample_end = sun4i_gpadc_sample_end, > }; > > struct sun4i_gpadc_iio { > @@ -277,7 +308,7 @@ static int sun4i_gpadc_temp_read(struct iio_dev *indio_dev, int *val) > if (info->no_irq) { > pm_runtime_get_sync(indio_dev->dev.parent); > > - regmap_read(info->regmap, SUN4I_GPADC_TEMP_DATA, val); > + regmap_read(info->regmap, info->data->temp_data, val); > > pm_runtime_mark_last_busy(indio_dev->dev.parent); > pm_runtime_put_autosuspend(indio_dev->dev.parent); > @@ -382,10 +413,8 @@ static irqreturn_t sun4i_gpadc_fifo_data_irq_handler(int irq, void *dev_id) > return IRQ_HANDLED; > } > > -static int sun4i_gpadc_runtime_suspend(struct device *dev) > +static int sun4i_gpadc_sample_end(struct sun4i_gpadc_iio *info) > { > - struct sun4i_gpadc_iio *info = iio_priv(dev_get_drvdata(dev)); > - > /* Disable the ADC on IP */ > regmap_write(info->regmap, SUN4I_GPADC_CTRL1, 0); > /* Disable temperature sensor on IP */ > @@ -394,19 +423,32 @@ static int sun4i_gpadc_runtime_suspend(struct device *dev) > return 0; > } > > -static int sun4i_gpadc_runtime_resume(struct device *dev) > +static int sunxi_ths_sample_end(struct sun4i_gpadc_iio *info) > +{ > + /* Disable temperature sensor */ > + regmap_write(info->regmap, SUNXI_THS_CTRL2, 0x0); > + > + return 0; > +} > + > +static int sun4i_gpadc_runtime_suspend(struct device *dev) > { > struct sun4i_gpadc_iio *info = iio_priv(dev_get_drvdata(dev)); > > + return info->data->sample_end(info); > +} > + > +static int sun4i_gpadc_sample_start(struct sun4i_gpadc_iio *info) > +{ > /* clkin = 6MHz */ > regmap_write(info->regmap, SUN4I_GPADC_CTRL0, > SUN4I_GPADC_CTRL0_ADC_CLK_DIVIDER(2) | > SUN4I_GPADC_CTRL0_FS_DIV(7) | > - SUN4I_GPADC_CTRL0_T_ACQ(63)); > + SUNXI_THS_ACQ0(63)); > regmap_write(info->regmap, SUN4I_GPADC_CTRL1, info->data->tp_mode_en); > regmap_write(info->regmap, SUN4I_GPADC_CTRL3, > - SUN4I_GPADC_CTRL3_FILTER_EN | > - SUN4I_GPADC_CTRL3_FILTER_TYPE(1)); > + SUNXI_THS_FILTER_EN | > + SUNXI_THS_FILTER_TYPE(1)); Why if these are temperature sensor features are we setting them in the general purpose ADC start function? > /* period = SUN4I_GPADC_TPR_TEMP_PERIOD * 256 * 16 / clkin; ~0.6s */ > regmap_write(info->regmap, SUN4I_GPADC_TPR, > SUN4I_GPADC_TPR_TEMP_ENABLE | > @@ -415,6 +457,35 @@ static int sun4i_gpadc_runtime_resume(struct device *dev) > return 0; > } > > +static int sunxi_ths_sample_start(struct sun4i_gpadc_iio *info) > +{ > + u32 value; > + > + if (info->data->ctrl0_map) > + regmap_write(info->regmap, SUNXI_THS_CTRL0, > + info->data->ctrl0_map); > + > + regmap_write(info->regmap, SUNXI_THS_CTRL2, > + info->data->ctrl2_map); > + > + regmap_write(info->regmap, SUNXI_THS_FILTER, > + info->data->filter_map); > + > + regmap_read(info->regmap, SUNXI_THS_CTRL2, &value); > + > + regmap_write(info->regmap, SUNXI_THS_CTRL2, > + info->data->sensor_en_map | value); > + > + return 0; > +} > + > +static int sun4i_gpadc_runtime_resume(struct device *dev) > +{ > + struct sun4i_gpadc_iio *info = iio_priv(dev_get_drvdata(dev)); > + > + return info->data->sample_start(info); > +} > + > static int sun4i_gpadc_get_temp(void *data, int *temp) > { > struct sun4i_gpadc_iio *info = data; > diff --git a/include/linux/mfd/sun4i-gpadc.h b/include/linux/mfd/sun4i-gpadc.h > index 78d31984a222..39e096c3ddac 100644 > --- a/include/linux/mfd/sun4i-gpadc.h > +++ b/include/linux/mfd/sun4i-gpadc.h > @@ -17,7 +17,6 @@ > #define SUN4I_GPADC_CTRL0_ADC_CLK_SELECT BIT(22) > #define SUN4I_GPADC_CTRL0_ADC_CLK_DIVIDER(x) ((GENMASK(1, 0) & (x)) << 20) > #define SUN4I_GPADC_CTRL0_FS_DIV(x) ((GENMASK(3, 0) & (x)) << 16) > -#define SUN4I_GPADC_CTRL0_T_ACQ(x) (GENMASK(15, 0) & (x)) > > #define SUN4I_GPADC_CTRL1 0x04 > > @@ -51,9 +50,6 @@ > > #define SUN4I_GPADC_CTRL3 0x0c > > -#define SUN4I_GPADC_CTRL3_FILTER_EN BIT(2) > -#define SUN4I_GPADC_CTRL3_FILTER_TYPE(x) (GENMASK(1, 0) & (x)) > - > #define SUN4I_GPADC_TPR 0x18 > > #define SUN4I_GPADC_TPR_TEMP_ENABLE BIT(16) > @@ -90,6 +86,21 @@ > /* 10s delay before suspending the IP */ > #define SUN4I_GPADC_AUTOSUSPEND_DELAY 10000 > > +/* SUNXI_THS COMMON REGISTERS + DEFINES */ > +#define SUNXI_THS_CTRL0 0x00 > +#define SUNXI_THS_CTRL2 0x40 > +#define SUNXI_THS_FILTER 0x70 > + > +#define SUNXI_THS_FILTER_EN BIT(2) > +#define SUNXI_THS_FILTER_TYPE(x) (GENMASK(1, 0) & (x)) > +#define SUNXI_THS_ACQ0(x) (GENMASK(15, 0) & (x)) > +#define SUNXI_THS_ACQ1(x) (GENMASK(31, 16) & ((x) << 16)) > + > +#define SUNXI_THS_TEMP_SENSE_EN0 BIT(0) > +#define SUNXI_THS_TEMP_SENSE_EN1 BIT(1) > +#define SUNXI_THS_TEMP_SENSE_EN2 BIT(2) > +#define SUNXI_THS_TEMP_SENSE_EN3 BIT(3) > + > struct sun4i_gpadc_dev { > struct device *dev; > struct regmap *regmap;