From: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
To: mchehab-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org,
wens-jdAy2FN1RRM@public.gmane.org,
linux-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org,
sean-hENCXIMQXOg@public.gmane.org,
p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org,
andi.shyti-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org
Cc: linux-media-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org
Subject: [PATCH v5 0/6] IR support for A83T
Date: Tue, 30 Jan 2018 18:46:50 +0100 [thread overview]
Message-ID: <20180130174656.10657-1-embed3d@gmail.com> (raw)
This patch series adds support for the sunxi A83T ir module and enhances
the sunxi-ir driver. Right now the base clock frequency for the ir driver
is a hard coded define and is set to 8 MHz.
This works for the most common ir receivers. On the Sinovoip Bananapi M3
the ir receiver needs, a 3 MHz base clock frequency to work without
problems with this driver.
This patch series adds support for an optinal property that makes it able
to override the default base clock frequency and enables the ir interface
on the a83t and the Bananapi M3.
changes since v4:
* rename cir pin from cir_pins to r_cir_pin
* drop unit-adress from r_cir_pin
* add a83t compatible to the cir node
* move muxing options to dtsi
* rename cir label and reorder it in the bananpim3.dts file
changes since v3:
* collecting all acks & reviewd by
* fixed typos
changes since v2:
* reorder cir pin (alphabetical)
* fix typo in documentation
changes since v1:
* fix typos, reword Documentation
* initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
* change dev_info() to dev_dbg()
* change naming to cir* in dts/dtsi
* Added acked Ackedi-by to related patch
* use whole memory block instead of registers needed + fix for h3/h5
changes since rfc:
* The property is now optinal. If the property is not available in
the dtb the driver uses the default base clock frequency.
* the driver prints out the the selected base clock frequency.
* changed devicetree property from base-clk-frequency to clock-frequency
Regards,
Philipp
Philipp Rossak (6):
media: rc: update sunxi-ir driver to get base clock frequency from
devicetree
media: dt: bindings: Update binding documentation for sunxi IR
controller
arm: dts: sun8i: a83t: Add the cir pin for the A83T
arm: dts: sun8i: a83t: Add support for the cir interface
arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller
arm: dts: sun8i: h3-h5: ir register size should be the whole memory
block
Documentation/devicetree/bindings/media/sunxi-ir.txt | 3 +++
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 5 +++++
arch/arm/boot/dts/sun8i-a83t.dtsi | 18 ++++++++++++++++++
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +-
drivers/media/rc/sunxi-cir.c | 19 +++++++++++--------
5 files changed, 38 insertions(+), 9 deletions(-)
--
2.11.0
next reply other threads:[~2018-01-30 17:46 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-30 17:46 Philipp Rossak [this message]
[not found] ` <20180130174656.10657-1-embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-01-30 17:46 ` [PATCH v5 1/6] media: rc: update sunxi-ir driver to get base clock frequency from devicetree Philipp Rossak
2018-01-30 17:46 ` [PATCH v5 2/6] media: dt: bindings: Update binding documentation for sunxi IR controller Philipp Rossak
2018-01-30 17:46 ` [PATCH v5 3/6] arm: dts: sun8i: a83t: Add the cir pin for the A83T Philipp Rossak
2018-01-30 17:46 ` [PATCH v5 4/6] arm: dts: sun8i: a83t: Add support for the cir interface Philipp Rossak
2018-01-30 17:46 ` [PATCH v5 5/6] arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller Philipp Rossak
2018-01-30 17:46 ` [PATCH v5 6/6] arm: dts: sun8i: h3-h5: ir register size should be the whole memory block Philipp Rossak
2018-02-12 11:00 ` [PATCH v5 0/6] IR support for A83T Philipp Rossak
[not found] ` <a1ce4422-33d7-1214-6527-0d299e97fe8b-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-02-13 7:58 ` Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180130174656.10657-1-embed3d@gmail.com \
--to=embed3d-re5jqeeqqe8avxtiumwx3w@public.gmane.org \
--cc=andi.shyti-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-media-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org \
--cc=mchehab-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=sean-hENCXIMQXOg@public.gmane.org \
--cc=wens-jdAy2FN1RRM@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).