From: Jonathan Cameron <jic23@kernel.org>
To: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: benjamin.gaignard@st.com, fabrice.gasnier@st.com,
linux-iio@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v6 2/9] counter: Documentation: Add Generic Counter sysfs documentation
Date: Sun, 20 May 2018 16:12:34 +0100 [thread overview]
Message-ID: <20180520161234.3707d397@archlinux> (raw)
In-Reply-To: <1bf56af37a1d6dab8181ce71f827914acdf5c4f7.1526487615.git.vilhelm.gray@gmail.com>
On Wed, 16 May 2018 13:50:55 -0400
William Breathitt Gray <vilhelm.gray@gmail.com> wrote:
> This patch adds standard documentation for the userspace sysfs
> attributes of the Generic Counter interface.
>
> Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Some really minor stuff inline. No functional changes.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> ---
> Documentation/ABI/testing/sysfs-bus-counter | 241 ++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 242 insertions(+)
> create mode 100644 Documentation/ABI/testing/sysfs-bus-counter
>
> diff --git a/Documentation/ABI/testing/sysfs-bus-counter b/Documentation/ABI/testing/sysfs-bus-counter
> new file mode 100644
> index 000000000000..e4a45d231b4f
> --- /dev/null
> +++ b/Documentation/ABI/testing/sysfs-bus-counter
> @@ -0,0 +1,241 @@
> +What: /sys/bus/counter/devices/counterX/countY/count
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Count data of Count Y represented as a string.
> +
> +What: /sys/bus/counter/devices/counterX/countY/ceiling
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Count value ceiling for Count Y. This is the upper limit for the
> + respective counter.
> +
> +What: /sys/bus/counter/devices/counterX/countY/floor
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Count value floor for Count Y. This is the lower limit for the
> + respective counter.
> +
> +What: /sys/bus/counter/devices/counterX/countY/count_mode
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Count mode for channel Y. The ceiling and floor values for
> + Count Y are used by the count mode where required. The following
> + count modes are available:
> +
> + Normal:
> + Counting is continuous in either direction.
> +
> + Range Limit:
> + An upper or lower limit is set, mimicking limit switches
> + in the mechanical counterpart. The upper limit is set to
> + the Count Y ceiling value, while the lower limit is set
> + to the Count Y floor value. The counter freezes at
> + count = ceiling when counting up, and at count = floor
> + when counting down. At either of these limits, the
> + counting is resumed only when the count direction is
> + reversed.
> +
> + Non-Recycle:
> + The counter is disabled whenever a counter overflow or
> + underflow takes place. The counter is re-enabled when a
> + new count value is loaded to the counter via a preset
> + operation or direct write.
> +
> + Modulo-N:
> + A count value boundary is set between the Count Y floor
> + value and the Count Y ceiling value. The counter is
> + reset to the Cunt Y floor value at count = ceiling when
> + counting up, while the counter is set to the Count Y
> + ceiling value at count = floor when counting down; the
> + counter does not freeze at the boundary points, but
> + counts continuously throughout.
> +
> +What: /sys/bus/counter/devices/counterX/countY/count_mode_available
> +What: /sys/bus/counter/devices/counterX/countY/error_noise_available
> +What: /sys/bus/counter/devices/counterX/countY/function_available
> +What: /sys/bus/counter/devices/counterX/countY/signalZ_action_available
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Discrete set of available values for the respective Count Y
> + configuration are listed in this file. Values are delineated by
> + newline characters.
> +
> +What: /sys/bus/counter/devices/counterX/countY/direction
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Read-only attribute that indicates the count direction of Count
> + Y. Two count directions are available: forward and backward.
> +
> + Some counter devices are able to determine the direction of
> + their counting. For example, quadrature encoding counters can
> + determine the direction of movement by evaluating the leading
> + phase of the respective A and B quadrature encoding signals.
> + This attribute exposes such count directions.
> +
> +What: /sys/bus/counter/devices/counterX/countY/enable
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Whether channel Y counter is enabled. Valid attribute values are
> + boolean.
> +
> + This attribute is intended to serve as a pause/unpause mechanism
> + for Count Y. Suppose a counter device is used to count the total
> + movement of a conveyor belt: this attribute allows an operator
> + to temporarily pause the counter, service the conveyor belt,
> + and then finally unpause the counter to continue where it had
> + left off.
> +
> +What: /sys/bus/counter/devices/counterX/countY/error_noise
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Read-only attribute that indicates whether excessive noise is
> + present at the channel Y counter inputs.
> +
> +What: /sys/bus/counter/devices/counterX/countY/function
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Count function mode of Count Y; count function evaluation is
> + triggered by conditions specified by the Count Y signalZ_action
> + attributes. The following count functions are available:
> +
> + Increase:
> + Accumulated count is incremented.
> +
> + Decrease:
> + Accumulated count is decremented.
> +
> + Pulse-Direction:
> + Rising edges on quadrature pair signal A updates the
> + respective count. The input level of quadrature pair
> + signal B determines direction.
> +
> + Quadrature x1 A:
> + If direction is forward, rising edges on quadrature pair
> + signal A updates the respective count; if the direction
> + is backward, falling edges on quadrature pair signal A
> + updates the respective count. Quadrature encoding
> + determines the direction.
> +
> + Quadrature x1 B:
> + If direction is forward, rising edges on quadrature pair
> + signal B updates the respective count; if the direction
> + is backward, falling edges on quadrature pair signal B
> + updates the respective count. Quadrature encoding
> + determines the direction.
> +
> + Quadrature x2 A:
> + Any state transition on quadrature pair signal A updates
> + the respective count. Quadrature encoding determines the
> + direction.
> +
> + Quadrature x2 B:
> + Any state transition on quadrature pair signal B updates
> + the respective count. Quadrature encoding determines the
> + direction.
> +
> + Quadrature x2 Rising:
> + Rising edges on either quadrature pair signals updates
> + the respective count. Quadrature encoding determines the
> + direction.
> +
> + Quadrature x2 Falling:
> + Falling edges on either quadrature pair signals updates
> + the respective count. Quadrature encoding determines the
> + direction.
> +
> + Quadrature x4:
> + Any state transition on either quadrature pair signals
> + updates the respective count. Quadrature encoding
> + determines the direction.
> +
> +What: /sys/bus/counter/devices/counterX/countY/name
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Read-only attribute that indicates the device-specific name of
> + Count Y. If possible, this should match the name of the
> + respective channel as it appears in the device datasheet
> + documentation text.
> +
> +What: /sys/bus/counter/devices/counterX/countY/preset
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + If the counter device supports preset registers, the preset
> + count for channel Y is provided by this attribute.
I would add a small block of text here saying what a "preset" typically is.
It is a term heavily used in encoders etc, but perhaps not some other types
of counter.
> +
> +What: /sys/bus/counter/devices/counterX/countY/preset_enable
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Whether channel Y counter preset operation is enabled. Valid
> + attribute values are boolean.
> +
> +What: /sys/bus/counter/devices/counterX/countY/signalZ_action
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Action mode of Count Y for Signal Z. This attribute indicates
> + the condition of Signal Z that triggers the count function
> + evaluation for Count Y. The following action modes are
> + available:
> +
> + None:
> + Signal does not trigger the count function. In
> + Pulse-Direction count function mode, this Signal is
> + evaluated as Direction.
> +
> + Rising Edge:
> + Low state transitions to high state.
> +
> + Falling Edge:
> + High state transitions to low state.
> +
> + Both Edges:
> + Any state transition.
> +
> +What: /sys/bus/counter/devices/counterX/name
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Read-only attribute that indicates the device-specific name of
> + the Counter. This should match the name of the device as it
> + appears in its respective datasheet documentation text.
As below, I'm not sure if "documentation text" makes it clearer or less clear..
> +
> +What: /sys/bus/counter/devices/counterX/num_counts
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Read-only attribute that indicates the total number of Counts
> + belonging to the Counter.
> +
> +What: /sys/bus/counter/devices/counterX/num_signals
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Read-only attribute that indicates the total number of Signals
> + belonging to the Counter.
> +
> +What: /sys/bus/counter/devices/counterX/signalY/signal
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Signal data of Signal Y represented as a string.
> +
> +What: /sys/bus/counter/devices/counterX/signalY/name
> +KernelVersion: 4.18
> +Contact: linux-iio@vger.kernel.org
> +Description:
> + Read-only attribute that indicates the device-specific name of
> + Signal Y. If possible, this should match the name of the
> + respective signal as it appears in the device datasheet
> + documentation text.
Not sure "documentation text" adds any clarity over the simply "device datasheet"
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 2a016d73ab72..1413e3eb49e5 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -3673,6 +3673,7 @@ COUNTER SUBSYSTEM
> M: William Breathitt Gray <vilhelm.gray@gmail.com>
> L: linux-iio@vger.kernel.org
> S: Maintained
> +F: Documentation/ABI/testing/sysfs-bus-counter*
> F: drivers/counter/
> F: include/linux/counter.h
>
next prev parent reply other threads:[~2018-05-20 15:12 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-16 17:50 [PATCH v6 0/9] Introduce the Counter subsystem William Breathitt Gray
2018-05-16 17:50 ` [PATCH v6 1/9] counter: Introduce the Generic Counter interface William Breathitt Gray
2018-05-20 15:06 ` Jonathan Cameron
2018-05-21 13:06 ` William Breathitt Gray
2018-05-16 17:50 ` [PATCH v6 2/9] counter: Documentation: Add Generic Counter sysfs documentation William Breathitt Gray
2018-05-20 15:12 ` Jonathan Cameron [this message]
2018-05-16 17:51 ` [PATCH v6 3/9] docs: Add Generic Counter interface documentation William Breathitt Gray
2018-05-19 15:30 ` kbuild test robot
2018-05-20 15:31 ` Jonathan Cameron
2018-05-21 13:47 ` William Breathitt Gray
2018-05-22 17:08 ` Jonathan Cameron
2018-05-25 9:26 ` Fabrice Gasnier
2018-05-25 13:00 ` William Breathitt Gray
2018-05-16 17:51 ` [PATCH v6 4/9] counter: 104-quad-8: Add Generic Counter interface support William Breathitt Gray
2018-05-19 13:16 ` kbuild test robot
2018-05-19 13:55 ` William Breathitt Gray
2018-05-19 13:16 ` [RFC PATCH] counter: 104-quad-8: quad8_ops can be static kbuild test robot
2018-05-20 15:42 ` [PATCH v6 4/9] counter: 104-quad-8: Add Generic Counter interface support Jonathan Cameron
2018-05-21 13:51 ` William Breathitt Gray
2018-05-16 17:51 ` [PATCH v6 5/9] counter: 104-quad-8: Documentation: Add Generic Counter sysfs documentation William Breathitt Gray
2018-05-16 17:51 ` [PATCH v6 6/9] dt-bindings: counter: Document stm32 quadrature encoder William Breathitt Gray
2018-05-17 16:23 ` Rob Herring
2018-05-17 18:07 ` William Breathitt Gray
2018-05-17 18:59 ` Benjamin Gaignard
2018-05-18 16:28 ` Rob Herring
2018-05-20 15:47 ` Jonathan Cameron
2018-06-04 13:03 ` Benjamin Gaignard
2018-05-16 17:52 ` [PATCH v6 7/9] counter: Add STM32 Timer " William Breathitt Gray
2018-05-16 17:52 ` [PATCH v6 8/9] counter: stm32-lptimer: add counter device William Breathitt Gray
2018-05-18 16:34 ` Rob Herring
2018-05-16 17:52 ` [PATCH v6 9/9] iio: counter: Remove IIO counter subdirectory William Breathitt Gray
2018-05-20 15:53 ` Jonathan Cameron
2018-05-21 13:58 ` William Breathitt Gray
2018-05-22 10:44 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180520161234.3707d397@archlinux \
--to=jic23@kernel.org \
--cc=benjamin.gaignard@st.com \
--cc=devicetree@vger.kernel.org \
--cc=fabrice.gasnier@st.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=vilhelm.gray@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).