[PATCH v5 0/5] Add support for QCOM Core Power Reduction

[PATCH v5 0/5] Add support for QCOM Core Power Reduction

[Niklas Cassel]

This series adds support for Core Power Reduction (CPR), a form of
Adaptive Voltage Scaling (AVS), found on certain Qualcomm SoCs.

This series is based on top of the qcs404 cpufreq patch series that
hasn't landed yet:
https://patchwork.kernel.org/project/linux-arm-msm/list/?series=173423
as well as that series' matching device tree changes:
https://patchwork.kernel.org/project/linux-arm-msm/list/?series=165457

CPR is a technology that reduces core power on a CPU or on other device.
It reads voltage settings from efuses (that have been written in
production), it uses these voltage settings as initial values, for each
OPP.

After moving to a certain OPP, CPR monitors dynamic factors such as
temperature, etc. and adjusts the voltage for that frequency accordingly
to save power and meet silicon characteristic requirements.

This driver has been developed together with Jorge Ramirez-Ortiz, and
is based on an RFC by Stephen Boyd[1], which in turn is based on work
by others on codeaurora.org[2].

[1] https://lkml.org/lkml/2015/9/18/833
[2] https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/regulator/cpr-regulator.c?h=msm-3.10

Changes since V4:
Implemented review comments from Stephen Boyd.
Removed suspend()/resume(), since they did the same things as ->power_on()/
->power_off() genpd callbacks.

Niklas Cassel (5):
  dt-bindings: power: avs: Add support for CPR (Core Power Reduction)
  power: avs: Add support for CPR (Core Power Reduction)
  arm64: dts: qcom: qcs404: Add CPR and populate OPP table
  arm64: defconfig: enable CONFIG_QCOM_CPR
  arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM

 .../bindings/power/avs/qcom,cpr.txt           |  130 ++
 MAINTAINERS                                   |    8 +
 arch/arm64/boot/dts/qcom/qcs404.dtsi          |  132 +-
 arch/arm64/configs/defconfig                  |    2 +
 drivers/power/avs/Kconfig                     |   15 +
 drivers/power/avs/Makefile                    |    1 +
 drivers/power/avs/qcom-cpr.c                  | 1755 +++++++++++++++++
 7 files changed, 2035 insertions(+), 8 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power/avs/qcom,cpr.txt
 create mode 100644 drivers/power/avs/qcom-cpr.c

-- 
2.23.0

[PATCH v5 1/5] dt-bindings: power: avs: Add support for CPR (Core Power Reduction)

[Niklas Cassel]

Add DT bindings to describe the CPR HW found on certain Qualcomm SoCs.

Co-developed-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes since v4:
-Dropped "qcom,*" properties as per review comment from
Stephen Boyd. This is now SoC config data in the driver
that changes based on the SoC compatible string.

 .../bindings/power/avs/qcom,cpr.txt           | 130 ++++++++++++++++++
 1 file changed, 130 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/power/avs/qcom,cpr.txt

diff --git a/Documentation/devicetree/bindings/power/avs/qcom,cpr.txt b/Documentation/devicetree/bindings/power/avs/qcom,cpr.txt
new file mode 100644
index 000000000000..ab0d5ebbad4e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/avs/qcom,cpr.txt
@@ -0,0 +1,130 @@
+QCOM CPR (Core Power Reduction)
+
+CPR (Core Power Reduction) is a technology to reduce core power on a CPU
+or other device. Each OPP of a device corresponds to a "corner" that has
+a range of valid voltages for a particular frequency. While the device is
+running at a particular frequency, CPR monitors dynamic factors such as
+temperature, etc. and suggests adjustments to the voltage to save power
+and meet silicon characteristic requirements.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: should be "qcom,qcs404-cpr", "qcom,cpr" for qcs404
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: base address and size of the rbcpr register region
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the CPR interrupt
+
+- clocks:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: phandle to the reference clock
+
+- clock-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "ref"
+
+- vdd-apc-supply:
+	Usage: required
+	Value type: <phandle>
+	Definition: phandle to the vdd-apc-supply regulator
+
+- #power-domain-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: should be 0
+
+- operating-points-v2:
+	Usage: required
+	Value type: <phandle>
+	Definition: A phandle to the OPP table containing the
+		    performance states supported by the CPR
+		    power domain
+
+- acc-syscon:
+	Usage: optional
+	Value type: <phandle>
+	Definition: phandle to syscon for writing ACC settings
+
+- nvmem-cells:
+	Usage: required
+	Value type: <phandle>
+	Definition: phandle to nvmem cells containing the data
+		    that makes up a fuse corner, for each fuse corner.
+		    As well as the CPR fuse revision.
+
+- nvmem-cell-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: should be "cpr_quotient_offset1", "cpr_quotient_offset2",
+		    "cpr_quotient_offset3", "cpr_init_voltage1",
+		    "cpr_init_voltage2", "cpr_init_voltage3", "cpr_quotient1",
+		    "cpr_quotient2", "cpr_quotient3", "cpr_ring_osc1",
+		    "cpr_ring_osc2", "cpr_ring_osc3", "cpr_fuse_revision"
+		    for qcs404.
+
+Example:
+
+	cpr_opp_table: cpr-opp-table {
+		compatible = "operating-points-v2-qcom-level";
+
+		cpr_opp1: opp1 {
+			opp-level = <1>;
+			qcom,opp-fuse-level = <1>;
+		};
+		cpr_opp2: opp2 {
+			opp-level = <2>;
+			qcom,opp-fuse-level = <2>;
+		};
+		cpr_opp3: opp3 {
+			opp-level = <3>;
+			qcom,opp-fuse-level = <3>;
+		};
+	};
+
+	power-controller@b018000 {
+		compatible = "qcom,qcs404-cpr", "qcom,cpr";
+		reg = <0x0b018000 0x1000>;
+		interrupts = <0 15 IRQ_TYPE_EDGE_RISING>;
+		clocks = <&xo_board>;
+		clock-names = "ref";
+		vdd-apc-supply = <&pms405_s3>;
+		#power-domain-cells = <0>;
+		operating-points-v2 = <&cpr_opp_table>;
+		acc-syscon = <&tcsr>;
+
+		nvmem-cells = <&cpr_efuse_quot_offset1>,
+			<&cpr_efuse_quot_offset2>,
+			<&cpr_efuse_quot_offset3>,
+			<&cpr_efuse_init_voltage1>,
+			<&cpr_efuse_init_voltage2>,
+			<&cpr_efuse_init_voltage3>,
+			<&cpr_efuse_quot1>,
+			<&cpr_efuse_quot2>,
+			<&cpr_efuse_quot3>,
+			<&cpr_efuse_ring1>,
+			<&cpr_efuse_ring2>,
+			<&cpr_efuse_ring3>,
+			<&cpr_efuse_revision>;
+		nvmem-cell-names = "cpr_quotient_offset1",
+			"cpr_quotient_offset2",
+			"cpr_quotient_offset3",
+			"cpr_init_voltage1",
+			"cpr_init_voltage2",
+			"cpr_init_voltage3",
+			"cpr_quotient1",
+			"cpr_quotient2",
+			"cpr_quotient3",
+			"cpr_ring_osc1",
+			"cpr_ring_osc2",
+			"cpr_ring_osc3",
+			"cpr_fuse_revision";
+	};
-- 
2.23.0

[PATCH v5 3/5] arm64: dts: qcom: qcs404: Add CPR and populate OPP table

[Niklas Cassel]

Add CPR and populate OPP table.

Co-developed-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404.dtsi | 132 +++++++++++++++++++++++++--
 1 file changed, 124 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index d03782e7bc11..30b9c7f8f200 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -44,7 +44,8 @@
 			#cooling-cells = <2>;
 			clocks = <&apcs_glb>;
 			operating-points-v2 = <&cpu_opp_table>;
-			cpu-supply = <&pms405_s3>;
+			power-domains = <&cpr>;
+			power-domain-names = "cpr";
 		};
 
 		CPU1: cpu@101 {
@@ -57,7 +58,8 @@
 			#cooling-cells = <2>;
 			clocks = <&apcs_glb>;
 			operating-points-v2 = <&cpu_opp_table>;
-			cpu-supply = <&pms405_s3>;
+			power-domains = <&cpr>;
+			power-domain-names = "cpr";
 		};
 
 		CPU2: cpu@102 {
@@ -70,7 +72,8 @@
 			#cooling-cells = <2>;
 			clocks = <&apcs_glb>;
 			operating-points-v2 = <&cpu_opp_table>;
-			cpu-supply = <&pms405_s3>;
+			power-domains = <&cpr>;
+			power-domain-names = "cpr";
 		};
 
 		CPU3: cpu@103 {
@@ -83,7 +86,8 @@
 			#cooling-cells = <2>;
 			clocks = <&apcs_glb>;
 			operating-points-v2 = <&cpu_opp_table>;
-			cpu-supply = <&pms405_s3>;
+			power-domains = <&cpr>;
+			power-domain-names = "cpr";
 		};
 
 		L2_0: l2-cache {
@@ -107,20 +111,37 @@
 	};
 
 	cpu_opp_table: cpu-opp-table {
-		compatible = "operating-points-v2";
+		compatible = "operating-points-v2-kryo-cpu";
 		opp-shared;
 
 		opp-1094400000 {
 			opp-hz = /bits/ 64 <1094400000>;
-			opp-microvolt = <1224000 1224000 1224000>;
+			required-opps = <&cpr_opp1>;
 		};
 		opp-1248000000 {
 			opp-hz = /bits/ 64 <1248000000>;
-			opp-microvolt = <1288000 1288000 1288000>;
+			required-opps = <&cpr_opp2>;
 		};
 		opp-1401600000 {
 			opp-hz = /bits/ 64 <1401600000>;
-			opp-microvolt = <1384000 1384000 1384000>;
+			required-opps = <&cpr_opp3>;
+		};
+	};
+
+	cpr_opp_table: cpr-opp-table {
+		compatible = "operating-points-v2-qcom-level";
+
+		cpr_opp1: opp1 {
+			opp-level = <1>;
+			qcom,opp-fuse-level = <1>;
+		};
+		cpr_opp2: opp2 {
+			opp-level = <2>;
+			qcom,opp-fuse-level = <2>;
+		};
+		cpr_opp3: opp3 {
+			opp-level = <3>;
+			qcom,opp-fuse-level = <3>;
 		};
 	};
 
@@ -310,6 +331,62 @@
 			tsens_caldata: caldata@d0 {
 				reg = <0x1f8 0x14>;
 			};
+			cpr_efuse_speedbin: speedbin@13c {
+				reg = <0x13c 0x4>;
+				bits = <2 3>;
+			};
+			cpr_efuse_quot_offset1: qoffset1@231 {
+				reg = <0x231 0x4>;
+				bits = <4 7>;
+			};
+			cpr_efuse_quot_offset2: qoffset2@232 {
+				reg = <0x232 0x4>;
+				bits = <3 7>;
+			};
+			cpr_efuse_quot_offset3: qoffset3@233 {
+				reg = <0x233 0x4>;
+				bits = <2 7>;
+			};
+			cpr_efuse_init_voltage1: ivoltage1@229 {
+				reg = <0x229 0x4>;
+				bits = <4 6>;
+			};
+			cpr_efuse_init_voltage2: ivoltage2@22a {
+				reg = <0x22a 0x4>;
+				bits = <2 6>;
+			};
+			cpr_efuse_init_voltage3: ivoltage3@22b {
+				reg = <0x22b 0x4>;
+				bits = <0 6>;
+			};
+			cpr_efuse_quot1: quot1@22b {
+				reg = <0x22b 0x4>;
+				bits = <6 12>;
+			};
+			cpr_efuse_quot2: quot2@22d {
+				reg = <0x22d 0x4>;
+				bits = <2 12>;
+			};
+			cpr_efuse_quot3: quot3@230 {
+				reg = <0x230 0x4>;
+				bits = <0 12>;
+			};
+			cpr_efuse_ring1: ring1@228 {
+				reg = <0x228 0x4>;
+				bits = <0 3>;
+			};
+			cpr_efuse_ring2: ring2@228 {
+				reg = <0x228 0x4>;
+				bits = <4 3>;
+			};
+			cpr_efuse_ring3: ring3@229 {
+				reg = <0x229 0x4>;
+				bits = <0 3>;
+			};
+			cpr_efuse_revision: revision@218 {
+				reg = <0x218 0x4>;
+				bits = <3 3>;
+			};
 		};
 
 		rng: rng@e3000 {
@@ -952,6 +1029,45 @@
 			clocks = <&sleep_clk>;
 		};
 
+		cpr: power-controller@b018000 {
+			compatible = "qcom,qcs404-cpr", "qcom,cpr";
+			reg = <0x0b018000 0x1000>;
+			interrupts = <0 15 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&xo_board>;
+			clock-names = "ref";
+			vdd-apc-supply = <&pms405_s3>;
+			#power-domain-cells = <0>;
+			operating-points-v2 = <&cpr_opp_table>;
+			acc-syscon = <&tcsr>;
+
+			nvmem-cells = <&cpr_efuse_quot_offset1>,
+				<&cpr_efuse_quot_offset2>,
+				<&cpr_efuse_quot_offset3>,
+				<&cpr_efuse_init_voltage1>,
+				<&cpr_efuse_init_voltage2>,
+				<&cpr_efuse_init_voltage3>,
+				<&cpr_efuse_quot1>,
+				<&cpr_efuse_quot2>,
+				<&cpr_efuse_quot3>,
+				<&cpr_efuse_ring1>,
+				<&cpr_efuse_ring2>,
+				<&cpr_efuse_ring3>,
+				<&cpr_efuse_revision>;
+			nvmem-cell-names = "cpr_quotient_offset1",
+				"cpr_quotient_offset2",
+				"cpr_quotient_offset3",
+				"cpr_init_voltage1",
+				"cpr_init_voltage2",
+				"cpr_init_voltage3",
+				"cpr_quotient1",
+				"cpr_quotient2",
+				"cpr_quotient3",
+				"cpr_ring_osc1",
+				"cpr_ring_osc2",
+				"cpr_ring_osc3",
+				"cpr_fuse_revision";
+		};
+
 		timer@b120000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-- 
2.23.0