* [v6,2/3] i2c: mux: pca954x: support property idle-state
2019-11-29 9:22 [v6,1/3] dt-bindings: i2c: support property idle-state Biwen Li
@ 2019-11-29 9:22 ` Biwen Li
2019-11-29 9:22 ` [v6,3/3] arm64: dts: fsl-ls208xa-rdb: fix an errata E-00013 Biwen Li
2019-12-02 23:15 ` [v6,1/3] dt-bindings: i2c: support property idle-state Rob Herring
2 siblings, 0 replies; 5+ messages in thread
From: Biwen Li @ 2019-11-29 9:22 UTC (permalink / raw)
To: peda, leoyang.li, robh+dt, mark.rutland
Cc: linux-i2c, linux-kernel, devicetree, Biwen Li
This supports property idle-state,if present,
overrides i2c-mux-idle-disconnect.
My use cases:
- Use the property idle-state to fix
an errata on LS2085ARDB and LS2088ARDB.
- Errata id: E-00013(board LS2085ARDB and
LS2088ARDB revision on Rev.B, Rev.C and Rev.D).
- About E-00013:
- Description: I2C1 and I2C3 buses
are missing pull-up.
- Impact: When the PCA954x device is tri-stated, the I2C bus
will float. This makes the I2C bus and its associated
downstream devices inaccessible.
- Hardware fix: Populate resistors R189 and R190 for I2C1
and resistors R228 and R229 for I2C3.
- Software fix: Remove the tri-state option from the PCA954x
driver(PCA954x always on enable status, specify a
channel zero in dts to fix the errata E-00013).
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
---
Change in v6:
- adjust log
Change in v5:
- add extra precaution for pca954x_init
Change in v4:
- rename function
pca954x_calculate_chan -> pca954x_regval
Change in v3:
- update subject and description
- add a helper function pca954x_calculate_chan()
Change in v2:
- update subject and description
- add property idle-state
drivers/i2c/muxes/i2c-mux-pca954x.c | 69 +++++++++++++++++++----------
1 file changed, 46 insertions(+), 23 deletions(-)
diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c b/drivers/i2c/muxes/i2c-mux-pca954x.c
index cd8753b29a63..6577ec873f59 100644
--- a/drivers/i2c/muxes/i2c-mux-pca954x.c
+++ b/drivers/i2c/muxes/i2c-mux-pca954x.c
@@ -87,7 +87,7 @@ struct pca954x {
u8 last_chan; /* last register value */
/* MUX_IDLE_AS_IS, MUX_IDLE_DISCONNECT or >= 0 for channel */
- s8 idle_state;
+ s32 idle_state;
struct i2c_client *client;
@@ -237,20 +237,23 @@ static int pca954x_reg_write(struct i2c_adapter *adap,
I2C_SMBUS_BYTE, &dummy);
}
+static u8 pca954x_regval(struct pca954x *data, u8 chan)
+{
+ /* We make switches look like muxes, not sure how to be smarter. */
+ if (data->chip->muxtype == pca954x_ismux)
+ return chan | data->chip->enable;
+ else
+ return 1 << chan;
+}
+
static int pca954x_select_chan(struct i2c_mux_core *muxc, u32 chan)
{
struct pca954x *data = i2c_mux_priv(muxc);
struct i2c_client *client = data->client;
- const struct chip_desc *chip = data->chip;
u8 regval;
int ret = 0;
- /* we make switches look like muxes, not sure how to be smarter */
- if (chip->muxtype == pca954x_ismux)
- regval = chan | chip->enable;
- else
- regval = 1 << chan;
-
+ regval = pca954x_regval(data, chan);
/* Only select the channel if its different from the last channel */
if (data->last_chan != regval) {
ret = pca954x_reg_write(muxc->parent, client, regval);
@@ -264,7 +267,7 @@ static int pca954x_deselect_mux(struct i2c_mux_core *muxc, u32 chan)
{
struct pca954x *data = i2c_mux_priv(muxc);
struct i2c_client *client = data->client;
- s8 idle_state;
+ s32 idle_state;
idle_state = READ_ONCE(data->idle_state);
if (idle_state >= 0)
@@ -410,6 +413,22 @@ static void pca954x_cleanup(struct i2c_mux_core *muxc)
i2c_mux_del_adapters(muxc);
}
+static int pca954x_init(struct i2c_client *client, struct pca954x *data)
+{
+ int ret;
+ if (data->idle_state >= 0) {
+ data->last_chan = pca954x_regval(data, data->idle_state);
+ } else {
+ /* Disconnect multiplexer */
+ data->last_chan = 0;
+ }
+ ret = i2c_smbus_write_byte(client, data->last_chan);
+ if (ret < 0)
+ data->last_chan = 0;
+
+ return ret;
+}
+
/*
* I2C init/probing/exit functions
*/
@@ -419,7 +438,6 @@ static int pca954x_probe(struct i2c_client *client,
struct i2c_adapter *adap = client->adapter;
struct device *dev = &client->dev;
struct device_node *np = dev->of_node;
- bool idle_disconnect_dt;
struct gpio_desc *gpio;
struct i2c_mux_core *muxc;
struct pca954x *data;
@@ -470,23 +488,24 @@ static int pca954x_probe(struct i2c_client *client,
}
}
- /* Write the mux register at addr to verify
+ data->idle_state = MUX_IDLE_AS_IS;
+ if (of_property_read_u32(np, "idle-state", &data->idle_state)) {
+ if (np && of_property_read_bool(np, "i2c-mux-idle-disconnect"))
+ data->idle_state = MUX_IDLE_DISCONNECT;
+ }
+
+ /*
+ * Write the mux register at addr to verify
* that the mux is in fact present. This also
- * initializes the mux to disconnected state.
+ * initializes the mux to a channel
+ * or disconnected state.
*/
- if (i2c_smbus_write_byte(client, 0) < 0) {
+ ret = pca954x_init(client, data);
+ if (ret < 0) {
dev_warn(dev, "probe failed\n");
return -ENODEV;
}
- data->last_chan = 0; /* force the first selection */
- data->idle_state = MUX_IDLE_AS_IS;
-
- idle_disconnect_dt = np &&
- of_property_read_bool(np, "i2c-mux-idle-disconnect");
- if (idle_disconnect_dt)
- data->idle_state = MUX_IDLE_DISCONNECT;
-
ret = pca954x_irq_setup(muxc);
if (ret)
goto fail_cleanup;
@@ -538,9 +557,13 @@ static int pca954x_resume(struct device *dev)
struct i2c_client *client = to_i2c_client(dev);
struct i2c_mux_core *muxc = i2c_get_clientdata(client);
struct pca954x *data = i2c_mux_priv(muxc);
+ int ret;
- data->last_chan = 0;
- return i2c_smbus_write_byte(client, 0);
+ ret = pca954x_init(client, data);
+ if (ret < 0)
+ dev_err(&client->dev, "failed to verify the mux, the mux maybe not present in fact\n");
+
+ return ret;
}
#endif
--
2.17.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [v6,3/3] arm64: dts: fsl-ls208xa-rdb: fix an errata E-00013
2019-11-29 9:22 [v6,1/3] dt-bindings: i2c: support property idle-state Biwen Li
2019-11-29 9:22 ` [v6,2/3] i2c: mux: pca954x: " Biwen Li
@ 2019-11-29 9:22 ` Biwen Li
2019-12-02 23:15 ` [v6,1/3] dt-bindings: i2c: support property idle-state Rob Herring
2 siblings, 0 replies; 5+ messages in thread
From: Biwen Li @ 2019-11-29 9:22 UTC (permalink / raw)
To: peda, leoyang.li, robh+dt, mark.rutland
Cc: linux-i2c, linux-kernel, devicetree, Biwen Li
Specify a channel zero in idle state to
avoid enterring tri-stated state for PCA9547.
About E-00013:
- Description: I2C1 and I2C3 buses
are missing pull-up.
- Impact: When the PCA954x device is tri-stated, the I2C bus
will float. This makes the I2C bus and its associated
downstream devices inaccessible.
- Hardware fix: Populate resistors R189 and R190 for I2C1
and resistors R228 and R229 for I2C3.
- Software fix: Remove the tri-state option from the PCA954x
driver(PCA954x always on enable status, specify a
channel zero in dts to fix the errata E-00013).
Signed-off-by: Biwen Li <biwen.li@nxp.com>
---
Change in v6:
- none
Change in v5:
- specify a channel zero when pca9547 in idle state.
arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
index 6fd7f63085c9..412f1bc0db5f 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
@@ -49,6 +49,7 @@
reg = <0x75>;
#address-cells = <1>;
#size-cells = <0>;
+ idle-state = <0>;
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
--
2.17.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [v6,1/3] dt-bindings: i2c: support property idle-state
2019-11-29 9:22 [v6,1/3] dt-bindings: i2c: support property idle-state Biwen Li
2019-11-29 9:22 ` [v6,2/3] i2c: mux: pca954x: " Biwen Li
2019-11-29 9:22 ` [v6,3/3] arm64: dts: fsl-ls208xa-rdb: fix an errata E-00013 Biwen Li
@ 2019-12-02 23:15 ` Rob Herring
2019-12-03 11:11 ` [EXT] " Biwen Li
2 siblings, 1 reply; 5+ messages in thread
From: Rob Herring @ 2019-12-02 23:15 UTC (permalink / raw)
To: Biwen Li
Cc: peda, leoyang.li, robh+dt, mark.rutland, linux-i2c, linux-kernel,
devicetree, Biwen Li
On Fri, 29 Nov 2019 17:22:20 +0800, Biwen Li wrote:
> This supports property idle-state
>
> Signed-off-by: Biwen Li <biwen.li@nxp.com>
> ---
> Change in v6:
> - none
>
> Change in v5:
> - none
>
> Change in v4:
> - none
>
> Change in v3:
> - update subject and description
> - add some information for property idle-state
>
> Change in v2:
> - update subject and description
> - add property idle-state
>
> Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt | 2 ++
> 1 file changed, 2 insertions(+)
>
Please add Acked-by/Reviewed-by tags when posting new versions. However,
there's no need to repost patches *only* to add the tags. The upstream
maintainer will do that for acks received on the version they apply.
If a tag was not added on purpose, please state why and what changed.
^ permalink raw reply [flat|nested] 5+ messages in thread