[PATCH 0/4] Add support for SC7180 display

[PATCH 0/4] Add support for SC7180 display

[Kalyan Thota]

SC7180 follows a newer architecture where in some flush controls have been re-organized to simplify programming and provide for future expandability.
Specifically:
1) The TIMING_<j> bits that control flush of INTF_<j> have been replaced with a common INTF flush bit which flushes the programming in the MDP_CTL_<id>_INTF_ACTIVE register
2) Individual flush bits for MERGE_3D, DSC and CDWN have been added which flush the programming in the MDP_CTL_<id>_MERGE_3D_ACTIVE, ... etc respectively
3) PERIPH flush bit has been added to flush DSP packets for DisplayPort

The complete datapath is described using the MDP_CTL_<id>_TOP and newly added ACTIVE registers to handle other sub blocks
such as interface (INTF) resources, PingPong buffer / Layer Mixer, Display Stream Compression (DSC) resources, writeback (WB) and 3D Merge
selections that are part of the datapath.

Kalyan Thota (4):
  dt-bindings: msm:disp: add sc7180 DPU variant
  msm:disp:dpu1: add support for display for SC7180 target
  msm:disp:dpu1: setup display datapath for SC7180 target
  msm:disp:dpu1: add mixer selection for display topology

 .../devicetree/bindings/display/msm/dpu.txt        |   4 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c        |  21 ++-
 .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c   |  21 ++-
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c     | 191 +++++++++++++++++++--
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h     |   6 +
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c         |  84 ++++++++-
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h         |  24 +++
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c        |  28 +++
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h        |   6 +
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c          |   3 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c            |   1 +
 drivers/gpu/drm/msm/msm_drv.c                      |   4 +-
 12 files changed, 370 insertions(+), 23 deletions(-)

-- 
1.9.1

[PATCH 1/4] dt-bindings: msm:disp: add sc7180 DPU variant

[Kalyan Thota]

Add a compatible string to support sc7180 dpu version.

Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
---
 Documentation/devicetree/bindings/display/msm/dpu.txt | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt
index a61dd40..551ae26 100644
--- a/Documentation/devicetree/bindings/display/msm/dpu.txt
+++ b/Documentation/devicetree/bindings/display/msm/dpu.txt
@@ -8,7 +8,7 @@ The DPU display controller is found in SDM845 SoC.
 
 MDSS:
 Required properties:
-- compatible: "qcom,sdm845-mdss"
+- compatible:  "qcom,sdm845-mdss", "qcom,sc7180-mdss"
 - reg: physical base address and length of contoller's registers.
 - reg-names: register region names. The following region is required:
   * "mdss"
@@ -41,7 +41,7 @@ Optional properties:
 
 MDP:
 Required properties:
-- compatible: "qcom,sdm845-dpu"
+- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu"
 - reg: physical base address and length of controller's registers.
 - reg-names : register region names. The following region is required:
   * "mdp"
-- 
1.9.1

[PATCH 2/4] msm:disp:dpu1: add support for display for SC7180 target

[Kalyan Thota]

Add display hw catalog changes for SC7180 target.

Changes in v1:
 - Configure register offsets and capabilities for the
   display hw blocks.

Changes in v2:
 - mdss_irq data type has changed in the dependent
   patch, accommodate the necessary changes.
 - Add co-developed-by tags in the commit msg (Stephen Boyd).

Changes in v3:
 - fix kernel checkpatch errors in v2

Changes in v4:
 - move documentation into seperate patch (Rob Herring).

This patch has dependency on the below series

https://patchwork.kernel.org/patch/11253647/

Co-developed-by: Shubhashree Dhar <dhar@codeaurora.org>
Signed-off-by: Shubhashree Dhar <dhar@codeaurora.org>
Co-developed-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
---
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 189 +++++++++++++++++++++++--
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h |   4 +
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c      |   3 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c        |   1 +
 drivers/gpu/drm/msm/msm_drv.c                  |   4 +-
 5 files changed, 188 insertions(+), 13 deletions(-)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
index 88f2664..1cf4509 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
@@ -11,11 +11,17 @@
 #include "dpu_hw_catalog_format.h"
 #include "dpu_kms.h"
 
-#define VIG_SDM845_MASK \
-	(BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_SCALER_QSEED3) | BIT(DPU_SSPP_QOS) |\
+#define VIG_MASK \
+	(BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) |\
 	BIT(DPU_SSPP_CSC_10BIT) | BIT(DPU_SSPP_CDP) | BIT(DPU_SSPP_QOS_8LVL) |\
 	BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_EXCL_RECT))
 
+#define VIG_SDM845_MASK \
+	(VIG_MASK | BIT(DPU_SSPP_SCALER_QSEED3))
+
+#define VIG_SC7180_MASK \
+	(VIG_MASK | BIT(DPU_SSPP_SCALER_QSEED4))
+
 #define DMA_SDM845_MASK \
 	(BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) | BIT(DPU_SSPP_QOS_8LVL) |\
 	BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_TS_PREFILL_REC1) |\
@@ -27,6 +33,9 @@
 #define MIXER_SDM845_MASK \
 	(BIT(DPU_MIXER_SOURCESPLIT) | BIT(DPU_DIM_LAYER))
 
+#define MIXER_SC7180_MASK \
+	(BIT(DPU_DIM_LAYER))
+
 #define PINGPONG_SDM845_MASK BIT(DPU_PINGPONG_DITHER)
 
 #define PINGPONG_SDM845_SPLIT_MASK \
@@ -60,6 +69,16 @@
 	.has_idle_pc = true,
 };
 
+static const struct dpu_caps sc7180_dpu_caps = {
+	.max_mixer_width = DEFAULT_DPU_OUTPUT_LINE_WIDTH,
+	.max_mixer_blendstages = 0x9,
+	.qseed_type = DPU_SSPP_SCALER_QSEED4,
+	.smart_dma_rev = DPU_SSPP_SMART_DMA_V2,
+	.ubwc_version = DPU_HW_UBWC_VER_20,
+	.has_dim_layer = true,
+	.has_idle_pc = true,
+};
+
 static struct dpu_mdp_cfg sdm845_mdp[] = {
 	{
 	.name = "top_0", .id = MDP_TOP,
@@ -85,6 +104,23 @@
 	},
 };
 
+static struct dpu_mdp_cfg sc7180_mdp[] = {
+	{
+	.name = "top_0", .id = MDP_TOP,
+	.base = 0x0, .len = 0x494,
+	.features = 0,
+	.highest_bank_bit = 0x3,
+	.clk_ctrls[DPU_CLK_CTRL_VIG0] = {
+		.reg_off = 0x2AC, .bit_off = 0},
+	.clk_ctrls[DPU_CLK_CTRL_DMA0] = {
+		.reg_off = 0x2AC, .bit_off = 8},
+	.clk_ctrls[DPU_CLK_CTRL_DMA1] = {
+		.reg_off = 0x2B4, .bit_off = 8},
+	.clk_ctrls[DPU_CLK_CTRL_CURSOR0] = {
+		.reg_off = 0x2BC, .bit_off = 8},
+	},
+};
+
 /*************************************************************
  * CTL sub blocks config
  *************************************************************/
@@ -116,6 +152,24 @@
 	},
 };
 
+static struct dpu_ctl_cfg sc7180_ctl[] = {
+	{
+	.name = "ctl_0", .id = CTL_0,
+	.base = 0x1000, .len = 0xE4,
+	.features = BIT(DPU_CTL_ACTIVE_CFG)
+	},
+	{
+	.name = "ctl_1", .id = CTL_1,
+	.base = 0x1200, .len = 0xE4,
+	.features = BIT(DPU_CTL_ACTIVE_CFG)
+	},
+	{
+	.name = "ctl_2", .id = CTL_2,
+	.base = 0x1400, .len = 0xE4,
+	.features = BIT(DPU_CTL_ACTIVE_CFG)
+	},
+};
+
 /*************************************************************
  * SSPP sub blocks config
  *************************************************************/
@@ -203,9 +257,23 @@
 		sdm845_dma_sblk_3, 13, SSPP_TYPE_DMA, DPU_CLK_CTRL_CURSOR1),
 };
 
+static struct dpu_sspp_cfg sc7180_sspp[] = {
+	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
+		sdm845_vig_sblk_0, 0,  SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
+	SSPP_BLK("sspp_8", SSPP_DMA0, 0x24000,  DMA_SDM845_MASK,
+		sdm845_dma_sblk_0, 1, SSPP_TYPE_DMA, DPU_CLK_CTRL_DMA0),
+	SSPP_BLK("sspp_9", SSPP_DMA1, 0x26000,  DMA_SDM845_MASK,
+		sdm845_dma_sblk_1, 5, SSPP_TYPE_DMA, DPU_CLK_CTRL_DMA1),
+	SSPP_BLK("sspp_10", SSPP_DMA2, 0x28000,  DMA_CURSOR_SDM845_MASK,
+		sdm845_dma_sblk_2, 9, SSPP_TYPE_DMA, DPU_CLK_CTRL_CURSOR0),
+};
+
 /*************************************************************
  * MIXER sub blocks config
  *************************************************************/
+
+/* SDM845 */
+
 static const struct dpu_lm_sub_blks sdm845_lm_sblk = {
 	.maxwidth = DEFAULT_DPU_OUTPUT_LINE_WIDTH,
 	.maxblendstages = 11, /* excluding base layer */
@@ -215,23 +283,46 @@
 	},
 };
 
-#define LM_BLK(_name, _id, _base, _pp, _lmpair) \
+#define LM_BLK(_name, _id, _base, _fmask, _sblk, _pp, _lmpair) \
 	{ \
 	.name = _name, .id = _id, \
 	.base = _base, .len = 0x320, \
-	.features = MIXER_SDM845_MASK, \
-	.sblk = &sdm845_lm_sblk, \
+	.features = _fmask, \
+	.sblk = _sblk, \
 	.pingpong = _pp, \
 	.lm_pair_mask = (1 << _lmpair) \
 	}
 
 static struct dpu_lm_cfg sdm845_lm[] = {
-	LM_BLK("lm_0", LM_0, 0x44000, PINGPONG_0, LM_1),
-	LM_BLK("lm_1", LM_1, 0x45000, PINGPONG_1, LM_0),
-	LM_BLK("lm_2", LM_2, 0x46000, PINGPONG_2, LM_5),
-	LM_BLK("lm_3", LM_3, 0x0, PINGPONG_MAX, 0),
-	LM_BLK("lm_4", LM_4, 0x0, PINGPONG_MAX, 0),
-	LM_BLK("lm_5", LM_5, 0x49000, PINGPONG_3, LM_2),
+	LM_BLK("lm_0", LM_0, 0x44000, MIXER_SDM845_MASK,
+		&sdm845_lm_sblk, PINGPONG_0, LM_1),
+	LM_BLK("lm_1", LM_1, 0x45000, MIXER_SDM845_MASK,
+		&sdm845_lm_sblk, PINGPONG_1, LM_0),
+	LM_BLK("lm_2", LM_2, 0x46000, MIXER_SDM845_MASK,
+		&sdm845_lm_sblk, PINGPONG_2, LM_5),
+	LM_BLK("lm_3", LM_3, 0x0, MIXER_SDM845_MASK,
+		&sdm845_lm_sblk, PINGPONG_MAX, 0),
+	LM_BLK("lm_4", LM_4, 0x0, MIXER_SDM845_MASK,
+		&sdm845_lm_sblk, PINGPONG_MAX, 0),
+	LM_BLK("lm_5", LM_5, 0x49000, MIXER_SDM845_MASK,
+		&sdm845_lm_sblk, PINGPONG_3, LM_2),
+};
+
+/* SC7180 */
+
+static const struct dpu_lm_sub_blks sc7180_lm_sblk = {
+	.maxwidth = DEFAULT_DPU_OUTPUT_LINE_WIDTH,
+	.maxblendstages = 7, /* excluding base layer */
+	.blendstage_base = { /* offsets relative to mixer base */
+		0x20, 0x38, 0x50, 0x68, 0x80, 0x98, 0xb0
+	},
+};
+
+static struct dpu_lm_cfg sc7180_lm[] = {
+	LM_BLK("lm_0", LM_0, 0x44000, MIXER_SC7180_MASK,
+		&sc7180_lm_sblk, PINGPONG_0, LM_1),
+	LM_BLK("lm_1", LM_1, 0x45000, MIXER_SC7180_MASK,
+		&sc7180_lm_sblk, PINGPONG_1, LM_0),
 };
 
 /*************************************************************
@@ -271,6 +362,11 @@
 	PP_BLK("pingpong_3", PINGPONG_3, 0x71800),
 };
 
+static struct dpu_pingpong_cfg sc7180_pp[] = {
+	PP_BLK_TE("pingpong_0", PINGPONG_0, 0x70000),
+	PP_BLK_TE("pingpong_1", PINGPONG_1, 0x70800),
+};
+
 /*************************************************************
  * INTF sub blocks config
  *************************************************************/
@@ -290,6 +386,11 @@
 	INTF_BLK("intf_3", INTF_3, 0x6B800, INTF_DP, 1),
 };
 
+static struct dpu_intf_cfg sc7180_intf[] = {
+	INTF_BLK("intf_0", INTF_0, 0x6A000, INTF_DP, 0),
+	INTF_BLK("intf_1", INTF_1, 0x6A800, INTF_DSI, 0),
+};
+
 /*************************************************************
  * VBIF sub blocks config
  *************************************************************/
@@ -340,6 +441,10 @@
 	{.fl = 0, .lut = 0x11222222223357}
 };
 
+static struct dpu_qos_lut_entry sc7180_qos_linear[] = {
+	{.fl = 0, .lut = 0x0011222222335777},
+};
+
 static struct dpu_qos_lut_entry sdm845_qos_macrotile[] = {
 	{.fl = 10, .lut = 0x344556677},
 	{.fl = 11, .lut = 0x3344556677},
@@ -349,10 +454,18 @@
 	{.fl = 0, .lut = 0x112233344556677},
 };
 
+static struct dpu_qos_lut_entry sc7180_qos_macrotile[] = {
+	{.fl = 0, .lut = 0x0011223344556677},
+};
+
 static struct dpu_qos_lut_entry sdm845_qos_nrt[] = {
 	{.fl = 0, .lut = 0x0},
 };
 
+static struct dpu_qos_lut_entry sc7180_qos_nrt[] = {
+	{.fl = 0, .lut = 0x0},
+};
+
 static struct dpu_perf_cfg sdm845_perf_data = {
 	.max_bw_low = 6800000,
 	.max_bw_high = 6800000,
@@ -392,6 +505,30 @@
 	},
 };
 
+static struct dpu_perf_cfg sc7180_perf_data = {
+	.max_bw_low = 3900000,
+	.max_bw_high = 5500000,
+	.min_core_ib = 2400000,
+	.min_llcc_ib = 800000,
+	.min_dram_ib = 800000,
+	.danger_lut_tbl = {0xff, 0xffff, 0x0},
+	.qos_lut_tbl = {
+		{.nentry = ARRAY_SIZE(sc7180_qos_linear),
+		.entries = sc7180_qos_linear
+		},
+		{.nentry = ARRAY_SIZE(sc7180_qos_macrotile),
+		.entries = sc7180_qos_macrotile
+		},
+		{.nentry = ARRAY_SIZE(sc7180_qos_nrt),
+		.entries = sc7180_qos_nrt
+		},
+	},
+	.cdp_cfg = {
+		{.rd_enable = 1, .wr_enable = 1},
+		{.rd_enable = 1, .wr_enable = 0}
+	},
+};
+
 /*************************************************************
  * Hardware catalog init
  *************************************************************/
@@ -425,9 +562,39 @@ static void sdm845_cfg_init(struct dpu_mdss_cfg *dpu_cfg)
 	};
 }
 
+/*
+ * sc7180_cfg_init(): populate sc7180 dpu sub-blocks reg offsets
+ * and instance counts.
+ */
+static void sc7180_cfg_init(struct dpu_mdss_cfg *dpu_cfg)
+{
+	*dpu_cfg = (struct dpu_mdss_cfg){
+		.caps = &sc7180_dpu_caps,
+		.mdp_count = ARRAY_SIZE(sc7180_mdp),
+		.mdp = sc7180_mdp,
+		.ctl_count = ARRAY_SIZE(sc7180_ctl),
+		.ctl = sc7180_ctl,
+		.sspp_count = ARRAY_SIZE(sc7180_sspp),
+		.sspp = sc7180_sspp,
+		.mixer_count = ARRAY_SIZE(sc7180_lm),
+		.mixer = sc7180_lm,
+		.pingpong_count = ARRAY_SIZE(sc7180_pp),
+		.pingpong = sc7180_pp,
+		.intf_count = ARRAY_SIZE(sc7180_intf),
+		.intf = sc7180_intf,
+		.vbif_count = ARRAY_SIZE(sdm845_vbif),
+		.vbif = sdm845_vbif,
+		.reg_dma_count = 1,
+		.dma_cfg = sdm845_regdma,
+		.perf = sc7180_perf_data,
+		.mdss_irqs = 0x3f,
+	};
+}
+
 static struct dpu_mdss_hw_cfg_handler cfg_handler[] = {
 	{ .hw_rev = DPU_HW_VER_400, .cfg_init = sdm845_cfg_init},
 	{ .hw_rev = DPU_HW_VER_401, .cfg_init = sdm845_cfg_init},
+	{ .hw_rev = DPU_HW_VER_620, .cfg_init = sc7180_cfg_init},
 };
 
 void dpu_hw_catalog_deinit(struct dpu_mdss_cfg *dpu_cfg)
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
index 0fd3f50..2607ef3 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
@@ -38,6 +38,7 @@
 #define DPU_HW_VER_401	DPU_HW_VER(4, 0, 1) /* sdm845 v2.0 */
 #define DPU_HW_VER_410	DPU_HW_VER(4, 1, 0) /* sdm670 v1.0 */
 #define DPU_HW_VER_500	DPU_HW_VER(5, 0, 0) /* sdm855 v1.0 */
+#define DPU_HW_VER_620	DPU_HW_VER(6, 2, 0) /* sc7180 v1.0 */
 
 
 #define IS_MSM8996_TARGET(rev) IS_DPU_MAJOR_MINOR_SAME((rev), DPU_HW_VER_170)
@@ -45,6 +46,7 @@
 #define IS_SDM845_TARGET(rev) IS_DPU_MAJOR_MINOR_SAME((rev), DPU_HW_VER_400)
 #define IS_SDM670_TARGET(rev) IS_DPU_MAJOR_MINOR_SAME((rev), DPU_HW_VER_410)
 #define IS_SDM855_TARGET(rev) IS_DPU_MAJOR_MINOR_SAME((rev), DPU_HW_VER_500)
+#define IS_SC7180_TARGET(rev) IS_DPU_MAJOR_MINOR_SAME((rev), DPU_HW_VER_620)
 
 
 #define DPU_HW_BLK_NAME_LEN	16
@@ -110,6 +112,7 @@ enum {
 	DPU_SSPP_SRC = 0x1,
 	DPU_SSPP_SCALER_QSEED2,
 	DPU_SSPP_SCALER_QSEED3,
+	DPU_SSPP_SCALER_QSEED4,
 	DPU_SSPP_SCALER_RGB,
 	DPU_SSPP_CSC,
 	DPU_SSPP_CSC_10BIT,
@@ -166,6 +169,7 @@ enum {
  */
 enum {
 	DPU_CTL_SPLIT_DISPLAY = 0x1,
+	DPU_CTL_ACTIVE_CFG,
 	DPU_CTL_MAX
 };
 
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c
index 5bc39ba..50ee90e 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c
@@ -152,7 +152,8 @@ static void _setup_mixer_ops(struct dpu_mdss_cfg *m,
 		unsigned long features)
 {
 	ops->setup_mixer_out = dpu_hw_lm_setup_out;
-	if (IS_SDM845_TARGET(m->hwversion) || IS_SDM670_TARGET(m->hwversion))
+	if (IS_SDM845_TARGET(m->hwversion) || IS_SDM670_TARGET(m->hwversion)
+	    || IS_SC7180_TARGET(m->hwversion))
 		ops->setup_blend_config = dpu_hw_lm_setup_blend_config_sdm845;
 	else
 		ops->setup_blend_config = dpu_hw_lm_setup_blend_config;
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c
index 58b0485..ee93ba3 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c
@@ -1111,6 +1111,7 @@ static int __maybe_unused dpu_runtime_resume(struct device *dev)
 
 static const struct of_device_id dpu_dt_match[] = {
 	{ .compatible = "qcom,sdm845-dpu", },
+	{ .compatible = "qcom,sc7180-dpu", },
 	{}
 };
 MODULE_DEVICE_TABLE(of, dpu_dt_match);
diff --git a/drivers/gpu/drm/msm/msm_drv.c b/drivers/gpu/drm/msm/msm_drv.c
index c84f0a8..f50fefb 100644
--- a/drivers/gpu/drm/msm/msm_drv.c
+++ b/drivers/gpu/drm/msm/msm_drv.c
@@ -1192,7 +1192,8 @@ static int add_display_components(struct device *dev,
 	 * the interfaces to our components list.
 	 */
 	if (of_device_is_compatible(dev->of_node, "qcom,mdss") ||
-	    of_device_is_compatible(dev->of_node, "qcom,sdm845-mdss")) {
+	    of_device_is_compatible(dev->of_node, "qcom,sdm845-mdss") ||
+	    of_device_is_compatible(dev->of_node, "qcom,sc7180-mdss")) {
 		ret = of_platform_populate(dev->of_node, NULL, NULL, dev);
 		if (ret) {
 			DRM_DEV_ERROR(dev, "failed to populate children devices\n");
@@ -1317,6 +1318,7 @@ static int msm_pdev_remove(struct platform_device *pdev)
 	{ .compatible = "qcom,mdp4", .data = (void *)KMS_MDP4 },
 	{ .compatible = "qcom,mdss", .data = (void *)KMS_MDP5 },
 	{ .compatible = "qcom,sdm845-mdss", .data = (void *)KMS_DPU },
+	{ .compatible = "qcom,sc7180-mdss", .data = (void *)KMS_DPU },
 	{}
 };
 MODULE_DEVICE_TABLE(of, dt_match);
-- 
1.9.1

[PATCH 3/4] msm:disp:dpu1: setup display datapath for SC7180 target

[Kalyan Thota]

Add changes to setup display datapath on SC7180 target.

Changes in v1:
 - Add changes to support ctl_active on SC7180 target.
 - While selecting the number of mixers in the topology
   consider the interface width.

Changes in v2:
 - Spawn topology mixer selection into separate patch (Rob Clark).
 - Add co-developed-by tags in the commit msg (Stephen Boyd).

Changes in v3:
 - Fix kernel checkpatch errors in v2.

This patch has dependency on the below series

https://patchwork.kernel.org/patch/11253747/

Co-developed-by: Shubhashree Dhar <dhar@codeaurora.org>
Signed-off-by: Shubhashree Dhar <dhar@codeaurora.org>
Co-developed-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
---
 .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c   | 21 +++++-
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c     |  1 +
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c         | 84 +++++++++++++++++++++-
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h         | 24 +++++++
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c        | 28 ++++++++
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h        |  6 ++
 6 files changed, 159 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
index b9c84fb..8cc8ad12 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
@@ -280,6 +280,14 @@ static void dpu_encoder_phys_vid_setup_timing_engine(
 	phys_enc->hw_intf->ops.setup_timing_gen(phys_enc->hw_intf,
 			&timing_params, fmt);
 	phys_enc->hw_ctl->ops.setup_intf_cfg(phys_enc->hw_ctl, &intf_cfg);
+
+	/* setup which pp blk will connect to this intf */
+	if (phys_enc->hw_intf->ops.bind_pingpong_blk)
+		phys_enc->hw_intf->ops.bind_pingpong_blk(
+				phys_enc->hw_intf,
+				true,
+				phys_enc->hw_pp->idx);
+
 	spin_unlock_irqrestore(phys_enc->enc_spinlock, lock_flags);
 
 	programmable_fetch_config(phys_enc, &timing_params);
@@ -435,6 +443,7 @@ static void dpu_encoder_phys_vid_enable(struct dpu_encoder_phys *phys_enc)
 {
 	struct dpu_hw_ctl *ctl;
 	u32 flush_mask = 0;
+	u32 intf_flush_mask = 0;
 
 	ctl = phys_enc->hw_ctl;
 
@@ -459,10 +468,18 @@ static void dpu_encoder_phys_vid_enable(struct dpu_encoder_phys *phys_enc)
 	ctl->ops.get_bitmask_intf(ctl, &flush_mask, phys_enc->hw_intf->idx);
 	ctl->ops.update_pending_flush(ctl, flush_mask);
 
+	if (ctl->ops.get_bitmask_active_intf)
+		ctl->ops.get_bitmask_active_intf(ctl, &intf_flush_mask,
+			phys_enc->hw_intf->idx);
+
+	if (ctl->ops.update_pending_intf_flush)
+		ctl->ops.update_pending_intf_flush(ctl, intf_flush_mask);
+
 skip_flush:
 	DPU_DEBUG_VIDENC(phys_enc,
-			 "update pending flush ctl %d flush_mask %x\n",
-			 ctl->idx - CTL_0, flush_mask);
+		"update pending flush ctl %d flush_mask 0%x intf_mask 0x%x\n",
+		ctl->idx - CTL_0, flush_mask, intf_flush_mask);
+
 
 	/* ctl_flush & timing engine enable will be triggered by framework */
 	if (phys_enc->enable_state == DPU_ENC_DISABLED)
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
index 1cf4509..0ee2b6c 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
@@ -374,6 +374,7 @@
 	{\
 	.name = _name, .id = _id, \
 	.base = _base, .len = 0x280, \
+	.features = BIT(DPU_CTL_ACTIVE_CFG), \
 	.type = _type, \
 	.controller_id = _ctrl_id, \
 	.prog_fetch_lines_worst_case = 24 \
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c
index 179e8d5..2ce4b5a 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.c
@@ -22,11 +22,15 @@
 #define   CTL_PREPARE                   0x0d0
 #define   CTL_SW_RESET                  0x030
 #define   CTL_LAYER_EXTN_OFFSET         0x40
+#define   CTL_INTF_ACTIVE               0x0F4
+#define   CTL_INTF_FLUSH                0x110
+#define   CTL_INTF_MASTER               0x134
 
 #define CTL_MIXER_BORDER_OUT            BIT(24)
 #define CTL_FLUSH_MASK_CTL              BIT(17)
 
 #define DPU_REG_RESET_TIMEOUT_US        2000
+#define  INTF_IDX       31
 
 static struct dpu_ctl_cfg *_ctl_offset(enum dpu_ctl ctl,
 		struct dpu_mdss_cfg *m,
@@ -100,11 +104,27 @@ static inline void dpu_hw_ctl_update_pending_flush(struct dpu_hw_ctl *ctx,
 	ctx->pending_flush_mask |= flushbits;
 }
 
+static inline void dpu_hw_ctl_update_pending_intf_flush(struct dpu_hw_ctl *ctx,
+		u32 flushbits)
+{
+	ctx->pending_intf_flush_mask |= flushbits;
+}
+
 static u32 dpu_hw_ctl_get_pending_flush(struct dpu_hw_ctl *ctx)
 {
 	return ctx->pending_flush_mask;
 }
 
+static inline void dpu_hw_ctl_trigger_flush_v1(struct dpu_hw_ctl *ctx)
+{
+
+	if (ctx->pending_flush_mask & BIT(INTF_IDX))
+		DPU_REG_WRITE(&ctx->hw, CTL_INTF_FLUSH,
+				ctx->pending_intf_flush_mask);
+
+	DPU_REG_WRITE(&ctx->hw, CTL_FLUSH, ctx->pending_flush_mask);
+}
+
 static inline void dpu_hw_ctl_trigger_flush(struct dpu_hw_ctl *ctx)
 {
 	trace_dpu_hw_ctl_trigger_pending_flush(ctx->pending_flush_mask,
@@ -222,6 +242,36 @@ static int dpu_hw_ctl_get_bitmask_intf(struct dpu_hw_ctl *ctx,
 	return 0;
 }
 
+static int dpu_hw_ctl_get_bitmask_intf_v1(struct dpu_hw_ctl *ctx,
+		u32 *flushbits, enum dpu_intf intf)
+{
+	switch (intf) {
+	case INTF_0:
+	case INTF_1:
+		*flushbits |= BIT(31);
+		break;
+	default:
+		return 0;
+	}
+	return 0;
+}
+
+static int dpu_hw_ctl_active_get_bitmask_intf(struct dpu_hw_ctl *ctx,
+		u32 *flushbits, enum dpu_intf intf)
+{
+	switch (intf) {
+	case INTF_0:
+		*flushbits |= BIT(0);
+		break;
+	case INTF_1:
+		*flushbits |= BIT(1);
+		break;
+	default:
+		return 0;
+	}
+	return 0;
+}
+
 static u32 dpu_hw_ctl_poll_reset_status(struct dpu_hw_ctl *ctx, u32 timeout_us)
 {
 	struct dpu_hw_blk_reg_map *c = &ctx->hw;
@@ -422,6 +472,24 @@ static void dpu_hw_ctl_setup_blendstage(struct dpu_hw_ctl *ctx,
 	DPU_REG_WRITE(c, CTL_LAYER_EXT3(lm), mixercfg_ext3);
 }
 
+
+static void dpu_hw_ctl_intf_cfg_v1(struct dpu_hw_ctl *ctx,
+		struct dpu_hw_intf_cfg *cfg)
+{
+	struct dpu_hw_blk_reg_map *c = &ctx->hw;
+	u32 intf_active = 0;
+	u32 mode_sel = 0;
+
+	if (cfg->intf_mode_sel == DPU_CTL_MODE_SEL_CMD)
+		mode_sel |= BIT(17);
+
+	intf_active = DPU_REG_READ(c, CTL_INTF_ACTIVE);
+	intf_active |= BIT(cfg->intf - INTF_0);
+
+	DPU_REG_WRITE(c, CTL_TOP, mode_sel);
+	DPU_REG_WRITE(c, CTL_INTF_ACTIVE, intf_active);
+}
+
 static void dpu_hw_ctl_intf_cfg(struct dpu_hw_ctl *ctx,
 		struct dpu_hw_intf_cfg *cfg)
 {
@@ -455,21 +523,31 @@ static void dpu_hw_ctl_intf_cfg(struct dpu_hw_ctl *ctx,
 static void _setup_ctl_ops(struct dpu_hw_ctl_ops *ops,
 		unsigned long cap)
 {
+	if (cap & BIT(DPU_CTL_ACTIVE_CFG)) {
+		ops->trigger_flush = dpu_hw_ctl_trigger_flush_v1;
+		ops->setup_intf_cfg = dpu_hw_ctl_intf_cfg_v1;
+		ops->get_bitmask_intf = dpu_hw_ctl_get_bitmask_intf_v1;
+		ops->get_bitmask_active_intf =
+			dpu_hw_ctl_active_get_bitmask_intf;
+		ops->update_pending_intf_flush =
+			dpu_hw_ctl_update_pending_intf_flush;
+	} else {
+		ops->trigger_flush = dpu_hw_ctl_trigger_flush;
+		ops->setup_intf_cfg = dpu_hw_ctl_intf_cfg;
+		ops->get_bitmask_intf = dpu_hw_ctl_get_bitmask_intf;
+	}
 	ops->clear_pending_flush = dpu_hw_ctl_clear_pending_flush;
 	ops->update_pending_flush = dpu_hw_ctl_update_pending_flush;
 	ops->get_pending_flush = dpu_hw_ctl_get_pending_flush;
-	ops->trigger_flush = dpu_hw_ctl_trigger_flush;
 	ops->get_flush_register = dpu_hw_ctl_get_flush_register;
 	ops->trigger_start = dpu_hw_ctl_trigger_start;
 	ops->trigger_pending = dpu_hw_ctl_trigger_pending;
-	ops->setup_intf_cfg = dpu_hw_ctl_intf_cfg;
 	ops->reset = dpu_hw_ctl_reset_control;
 	ops->wait_reset_status = dpu_hw_ctl_wait_reset_status;
 	ops->clear_all_blendstages = dpu_hw_ctl_clear_all_blendstages;
 	ops->setup_blendstage = dpu_hw_ctl_setup_blendstage;
 	ops->get_bitmask_sspp = dpu_hw_ctl_get_bitmask_sspp;
 	ops->get_bitmask_mixer = dpu_hw_ctl_get_bitmask_mixer;
-	ops->get_bitmask_intf = dpu_hw_ctl_get_bitmask_intf;
 };
 
 static struct dpu_hw_blk_ops dpu_hw_ops;
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
index d3ae939..1e3973c 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
@@ -91,6 +91,15 @@ struct dpu_hw_ctl_ops {
 		u32 flushbits);
 
 	/**
+	 * OR in the given flushbits to the cached pending_intf_flush_mask
+	 * No effect on hardware
+	 * @ctx       : ctl path ctx pointer
+	 * @flushbits : module flushmask
+	 */
+	void (*update_pending_intf_flush)(struct dpu_hw_ctl *ctx,
+		u32 flushbits);
+
+	/**
 	 * Write the value of the pending_flush_mask to hardware
 	 * @ctx       : ctl path ctx pointer
 	 */
@@ -130,11 +139,24 @@ struct dpu_hw_ctl_ops {
 	uint32_t (*get_bitmask_mixer)(struct dpu_hw_ctl *ctx,
 		enum dpu_lm blk);
 
+	/**
+	 * Query the value of the intf flush mask
+	 * No effect on hardware
+	 * @ctx       : ctl path ctx pointer
+	 */
 	int (*get_bitmask_intf)(struct dpu_hw_ctl *ctx,
 		u32 *flushbits,
 		enum dpu_intf blk);
 
 	/**
+	 * Query the value of the intf active flush mask
+	 * No effect on hardware
+	 * @ctx       : ctl path ctx pointer
+	 */
+	int (*get_bitmask_active_intf)(struct dpu_hw_ctl *ctx,
+		u32 *flushbits, enum dpu_intf blk);
+
+	/**
 	 * Set all blend stages to disabled
 	 * @ctx       : ctl path ctx pointer
 	 */
@@ -159,6 +181,7 @@ struct dpu_hw_ctl_ops {
  * @mixer_count: number of mixers
  * @mixer_hw_caps: mixer hardware capabilities
  * @pending_flush_mask: storage for pending ctl_flush managed via ops
+ * @pending_intf_flush_mask: pending INTF flush
  * @ops: operation list
  */
 struct dpu_hw_ctl {
@@ -171,6 +194,7 @@ struct dpu_hw_ctl {
 	int mixer_count;
 	const struct dpu_lm_cfg *mixer_hw_caps;
 	u32 pending_flush_mask;
+	u32 pending_intf_flush_mask;
 
 	/* ops */
 	struct dpu_hw_ctl_ops ops;
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
index dcd87cd..eff5e6a 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
@@ -56,6 +56,8 @@
 #define   INTF_FRAME_COUNT              0x0AC
 #define   INTF_LINE_COUNT               0x0B0
 
+#define   INTF_MUX                      0x25C
+
 static struct dpu_intf_cfg *_intf_offset(enum dpu_intf intf,
 		struct dpu_mdss_cfg *m,
 		void __iomem *addr,
@@ -218,6 +220,30 @@ static void dpu_hw_intf_setup_prg_fetch(
 	DPU_REG_WRITE(c, INTF_CONFIG, fetch_enable);
 }
 
+static void dpu_hw_intf_bind_pingpong_blk(
+		struct dpu_hw_intf *intf,
+		bool enable,
+		const enum dpu_pingpong pp)
+{
+	struct dpu_hw_blk_reg_map *c;
+	u32 mux_cfg;
+
+	if (!intf)
+		return;
+
+	c = &intf->hw;
+
+	mux_cfg = DPU_REG_READ(c, INTF_MUX);
+	mux_cfg &= ~0xf;
+
+	if (enable)
+		mux_cfg |= (pp - PINGPONG_0) & 0x7;
+	else
+		mux_cfg |= 0xf;
+
+	DPU_REG_WRITE(c, INTF_MUX, mux_cfg);
+}
+
 static void dpu_hw_intf_get_status(
 		struct dpu_hw_intf *intf,
 		struct intf_status *s)
@@ -254,6 +280,8 @@ static void _setup_intf_ops(struct dpu_hw_intf_ops *ops,
 	ops->get_status = dpu_hw_intf_get_status;
 	ops->enable_timing = dpu_hw_intf_enable_timing_engine;
 	ops->get_line_count = dpu_hw_intf_get_line_count;
+	if (cap & BIT(DPU_CTL_ACTIVE_CFG))
+		ops->bind_pingpong_blk = dpu_hw_intf_bind_pingpong_blk;
 }
 
 static struct dpu_hw_blk_ops dpu_hw_ops;
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
index b03acc2..a1e0ef3 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
@@ -52,6 +52,8 @@ struct intf_status {
  * @ enable_timing: enable/disable timing engine
  * @ get_status: returns if timing engine is enabled or not
  * @ get_line_count: reads current vertical line counter
+ * @bind_pingpong_blk: enable/disable the connection with pingpong which will
+ *                     feed pixels to this interface
  */
 struct dpu_hw_intf_ops {
 	void (*setup_timing_gen)(struct dpu_hw_intf *intf,
@@ -68,6 +70,10 @@ struct dpu_hw_intf_ops {
 			struct intf_status *status);
 
 	u32 (*get_line_count)(struct dpu_hw_intf *intf);
+
+	void (*bind_pingpong_blk)(struct dpu_hw_intf *intf,
+			bool enable,
+			const enum dpu_pingpong pp);
 };
 
 struct dpu_hw_intf {
-- 
1.9.1

[PATCH 4/4] msm:disp:dpu1: add mixer selection for display topology

[Kalyan Thota]

mixer selection in the display topology is based on multiple
factors
1) mixers available in the hw
2) interfaces to be enabled
3) merge capability

change will pickup mixer as per the topology need.

Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
---
 drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c    | 21 ++++++++++++++++++---
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c |  1 +
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h |  2 ++
 3 files changed, 21 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
index d82ea99..067ef0b 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
@@ -58,7 +58,7 @@
 
 #define IDLE_SHORT_TIMEOUT	1
 
-#define MAX_VDISPLAY_SPLIT 1080
+#define MAX_HDISPLAY_SPLIT 1080
 
 /* timeout in frames waiting for frame done */
 #define DPU_ENCODER_FRAME_DONE_TIMEOUT_FRAMES 5
@@ -534,8 +534,23 @@ static struct msm_display_topology dpu_encoder_get_topology(
 		if (dpu_enc->phys_encs[i])
 			intf_count++;
 
-	/* User split topology for width > 1080 */
-	topology.num_lm = (mode->vdisplay > MAX_VDISPLAY_SPLIT) ? 2 : 1;
+	/* Datapath topology selection
+	 *
+	 * Dual display
+	 * 2 LM, 2 INTF ( Split display using 2 interfaces)
+	 *
+	 * Single display
+	 * 1 LM, 1 INTF
+	 * 2 LM, 1 INTF (stream merge to support high resolution interfaces)
+	 *
+	 */
+	if (intf_count == 2)
+		topology.num_lm = 2;
+	else if (!dpu_kms->catalog->caps->has_3d_merge)
+		topology.num_lm = 1;
+	else
+		topology.num_lm = (mode->hdisplay > MAX_HDISPLAY_SPLIT) ? 2 : 1;
+
 	topology.num_enc = 0;
 	topology.num_intf = intf_count;
 
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
index 0ee2b6c..de69f71 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
@@ -67,6 +67,7 @@
 	.has_src_split = true,
 	.has_dim_layer = true,
 	.has_idle_pc = true,
+	.has_3d_merge = true,
 };
 
 static const struct dpu_caps sc7180_dpu_caps = {
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
index 2607ef3..d0cb41c 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
@@ -287,6 +287,7 @@ struct dpu_qos_lut_tbl {
  * @has_src_split      source split feature status
  * @has_dim_layer      dim layer feature status
  * @has_idle_pc        indicate if idle power collapse feature is supported
+ * @has_3d_merge       indicate if 3D merge is supported
  */
 struct dpu_caps {
 	u32 max_mixer_width;
@@ -297,6 +298,7 @@ struct dpu_caps {
 	bool has_src_split;
 	bool has_dim_layer;
 	bool has_idle_pc;
+	bool has_3d_merge;
 };
 
 /**
-- 
1.9.1

Re: [PATCH 1/4] dt-bindings: msm:disp: add sc7180 DPU variant

[Rob Herring]

On Mon, 25 Nov 2019 17:29:26 +0530, Kalyan Thota wrote:
> Add a compatible string to support sc7180 dpu version.
> 
> Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
> ---
>  Documentation/devicetree/bindings/display/msm/dpu.txt | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 

Acked-by: Rob Herring <robh@kernel.org>