From: Andrey Konovalov <andrey.konovalov@linaro.org>
To: mchehab@kernel.org, robh+dt@kernel.org
Cc: linux-media@vger.kernel.org, devicetree@vger.kernel.org,
dave.stevenson@raspberrypi.com, peter.griffin@linaro.org,
Andrey Konovalov <andrey.konovalov@linaro.org>
Subject: [PATCH 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding
Date: Wed, 11 Dec 2019 14:54:40 +0300 [thread overview]
Message-ID: <20191211115441.10637-2-andrey.konovalov@linaro.org> (raw)
In-Reply-To: <20191211115441.10637-1-andrey.konovalov@linaro.org>
Add YAML device tree binding for IMX219 CMOS image sensor, and
the relevant MAINTAINERS entries.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
---
.../devicetree/bindings/media/i2c/imx219.yaml | 112 ++++++++++++++++++
MAINTAINERS | 8 ++
2 files changed, 120 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/imx219.yaml b/Documentation/devicetree/bindings/media/i2c/imx219.yaml
new file mode 100644
index 000000000000..5e4293c21933
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx219.yaml
@@ -0,0 +1,112 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/imx219.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
+
+maintainers:
+ - Dave Stevenson <dave.stevenson@raspberrypi.com>
+
+description: |-
+ The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor
+ with an active array size of 3280H x 2464V. It is programmable through
+ I2C interface. The I2C address is fixed to 0x10 as per sensor data sheet.
+ Image data is sent through MIPI CSI-2, which is configured as either 2 or
+ 4 data lanes.
+
+properties:
+ compatible:
+ const: sony,imx219
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: xclk
+
+ VDIG-supply:
+ description:
+ Digital I/O voltage supply, 1.8 volts
+
+ VANA-supply:
+ description:
+ Analog voltage supply, 2.8 volts
+
+ VDDL-supply:
+ description:
+ Digital core voltage supply, 1.2 volts
+
+ xclr-gpios:
+ description: |-
+ Reference to the GPIO connected to the xclr pin, if any.
+ Must be released after all supplies are applied.
+ This is an active high signal to the imx219.
+
+ clock-noncontinuous:
+ description: |-
+ Presence of this boolean property decides whether the MIPI CSI-2 clock
+ is continuous or non-continuous.
+
+ camera-clk: true
+
+ port: true
+
+ data-lanes:
+ description: |-
+ Should be <1 2 3 4> for four-lane operation, or <1 2> for two-lane
+ operation.
+ const: <1 2>
+ clock-lanes:
+ const: <0>
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - VANA-supply
+ - VDIG-supply
+ - VDDL-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ imx219: sensor@10 {
+ compatible = "sony,imx219";
+ reg = <0x10>;
+ clocks = <&imx219_clk>;
+ clock-names = "xclk";
+ VANA-supply = <&imx219_vana>; /* 2.8v */
+ VDIG-supply = <&imx219_vdig>; /* 1.8v */
+ VDDL-supply = <&imx219_vddl>; /* 1.2v */
+
+ imx219_clk: camera-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+
+ port {
+ imx219_0: endpoint {
+ remote-endpoint = <&csi1_ep>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ clock-noncontinuous;
+ bus-type = <4>;
+ };
+ };
+ };
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 02d5278a4c9a..3baf2954d2f4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15339,6 +15339,14 @@ S: Maintained
F: drivers/media/i2c/imx214.c
F: Documentation/devicetree/bindings/media/i2c/sony,imx214.txt
+SONY IMX219 SENSOR DRIVER
+M: Dave Stevenson <dave.stevenson@raspberrypi.com>
+L: linux-media@vger.kernel.org
+T: git git://linuxtv.org/media_tree.git
+S: Maintained
+F: drivers/media/i2c/imx219.c
+F: Documentation/devicetree/bindings/media/i2c/imx219.yaml
+
SONY IMX258 SENSOR DRIVER
M: Sakari Ailus <sakari.ailus@linux.intel.com>
L: linux-media@vger.kernel.org
--
2.17.1
next prev parent reply other threads:[~2019-12-11 11:55 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-11 11:54 [PATCH 0/2] Add IMX219 CMOS image sensor support Andrey Konovalov
2019-12-11 11:54 ` Andrey Konovalov [this message]
2019-12-19 21:00 ` [PATCH 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding Rob Herring
2019-12-11 11:54 ` [PATCH 2/2] media: i2c: Add driver for Sony IMX219 sensor Andrey Konovalov
2019-12-14 5:52 ` Ezequiel Garcia
2019-12-18 22:29 ` Andrey Konovalov
2019-12-19 15:36 ` Dave Stevenson
2019-12-20 17:15 ` Andrey Konovalov
2019-12-19 15:53 ` Ezequiel Garcia
2019-12-20 17:28 ` Andrey Konovalov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191211115441.10637-2-andrey.konovalov@linaro.org \
--to=andrey.konovalov@linaro.org \
--cc=dave.stevenson@raspberrypi.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=peter.griffin@linaro.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).