Linux-Devicetree Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH AUTOSEL 5.4 050/459] arm64: dts: marvell: clearfog-gt-8k: fix switch cpu port node
       [not found] <20200214160149.11681-1-sashal@kernel.org>
@ 2020-02-14 15:55 ` Sasha Levin
  2020-02-14 15:55 ` [PATCH AUTOSEL 5.4 063/459] dt-bindings: iio: adc: ad7606: Fix wrong maxItems value Sasha Levin
                   ` (24 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:55 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Baruch Siach, Denis Odintsov, Andrew Lunn, Gregory CLEMENT,
	Sasha Levin, linux-arm-kernel, devicetree, netdev

From: Baruch Siach <baruch@tkos.co.il>

[ Upstream commit 62bba54d99407aedfe9b0a02e72e23c06e2b0116 ]

Explicitly set the switch cpu (upstream) port phy-mode and managed
properties. This fixes the Marvell 88E6141 switch serdes configuration
with the recently enabled phylink layer.

Fixes: a6120833272c ("arm64: dts: add support for SolidRun Clearfog GT 8K")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
index bd881497b8729..a211a046b2f2f 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
@@ -408,6 +408,8 @@
 				reg = <5>;
 				label = "cpu";
 				ethernet = <&cp1_eth2>;
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
 			};
 		};
 
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 063/459] dt-bindings: iio: adc: ad7606: Fix wrong maxItems value
       [not found] <20200214160149.11681-1-sashal@kernel.org>
  2020-02-14 15:55 ` [PATCH AUTOSEL 5.4 050/459] arm64: dts: marvell: clearfog-gt-8k: fix switch cpu port node Sasha Levin
@ 2020-02-14 15:55 ` Sasha Levin
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 148/459] arm64: dts: rockchip: Fix NanoPC-T4 cooling maps Sasha Levin
                   ` (23 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:55 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Beniamin Bia, Rob Herring, Sasha Levin, linux-fbdev, linux-iio,
	devicetree

From: Beniamin Bia <beniamin.bia@analog.com>

[ Upstream commit a6c4f77cb3b11f81077b53c4a38f21b92d41f21e ]

This patch set the correct value for oversampling maxItems. In the
original example, appears 3 items for oversampling while the maxItems
is set to 1, this patch fixes those issues.

Fixes: 416f882c3b40 ("dt-bindings: iio: adc: Migrate AD7606 documentation to yaml")
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
index cc544fdc38bea..bc8aed17800d3 100644
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
@@ -85,7 +85,7 @@ properties:
       Must be the device tree identifier of the over-sampling
       mode pins. As the line is active high, it should be marked
       GPIO_ACTIVE_HIGH.
-    maxItems: 1
+    maxItems: 3
 
   adi,sw-mode:
     description:
@@ -128,9 +128,9 @@ examples:
                 adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
                 reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
                 adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
-                adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH
-                                                &gpio 23 GPIO_ACTIVE_HIGH
-                                                &gpio 26 GPIO_ACTIVE_HIGH>;
+                adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>,
+                                               <&gpio 23 GPIO_ACTIVE_HIGH>,
+                                               <&gpio 26 GPIO_ACTIVE_HIGH>;
                 standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
                 adi,sw-mode;
         };
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 148/459] arm64: dts: rockchip: Fix NanoPC-T4 cooling maps
       [not found] <20200214160149.11681-1-sashal@kernel.org>
  2020-02-14 15:55 ` [PATCH AUTOSEL 5.4 050/459] arm64: dts: marvell: clearfog-gt-8k: fix switch cpu port node Sasha Levin
  2020-02-14 15:55 ` [PATCH AUTOSEL 5.4 063/459] dt-bindings: iio: adc: ad7606: Fix wrong maxItems value Sasha Levin
@ 2020-02-14 15:56 ` Sasha Levin
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 150/459] arm64: dts: uDPU: fix broken ethernet Sasha Levin
                   ` (22 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:56 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Robin Murphy, Heiko Stuebner, Sasha Levin, devicetree,
	linux-arm-kernel, linux-rockchip

From: Robin Murphy <robin.murphy@arm.com>

[ Upstream commit a793e19c15f25a126138ac4ae9facf9204754af3 ]

Although it appeared to follow logically from the bindings, apparently
the thermal framework can't properly cope with a single cooling device
being shared between multiple maps. The CPU zone is probably easier to
overheat, so remove the references to the (optional) fan from the GPU
cooling zone to avoid things getting confused. Hopefully GPU-intensive
tasks will leak enough heat across to the CPU zone to still hit the
fan trips before reaching critical GPU temperatures.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/5bb39f3115df1a487d717d3ae87e523b03749379.1573908197.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../boot/dts/rockchip/rk3399-nanopc-t4.dts    | 27 -------------------
 1 file changed, 27 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts b/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts
index 2a127985ab171..d3ed8e5e770f1 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts
@@ -94,33 +94,6 @@
 	};
 };
 
-&gpu_thermal {
-	trips {
-		gpu_warm: gpu_warm {
-			temperature = <55000>;
-			hysteresis = <2000>;
-			type = "active";
-		};
-
-		gpu_hot: gpu_hot {
-			temperature = <65000>;
-			hysteresis = <2000>;
-			type = "active";
-		};
-	};
-	cooling-maps {
-		map1 {
-			trip = <&gpu_warm>;
-			cooling-device = <&fan THERMAL_NO_LIMIT 1>;
-		};
-
-		map2 {
-			trip = <&gpu_hot>;
-			cooling-device = <&fan 2 THERMAL_NO_LIMIT>;
-		};
-	};
-};
-
 &pinctrl {
 	ir {
 		ir_rx: ir-rx {
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 150/459] arm64: dts: uDPU: fix broken ethernet
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (2 preceding siblings ...)
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 148/459] arm64: dts: rockchip: Fix NanoPC-T4 cooling maps Sasha Levin
@ 2020-02-14 15:56 ` Sasha Levin
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 159/459] arm64: dts: allwinner: H6: Add PMU mode Sasha Levin
                   ` (21 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:56 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Russell King, Gregory CLEMENT, Sasha Levin, linux-arm-kernel, devicetree

From: Russell King <rmk+kernel@armlinux.org.uk>

[ Upstream commit 1eebac0240580b531954b02c05068051df41142a ]

The uDPU uses both ethernet controllers, which ties up COMPHY 0 for
eth1 and COMPHY 1 for eth0, with no USB3 comphy.  The addition of
COMPHY support made the kernel override the setup by the boot loader
breaking this platform by assuming that COMPHY 0 was always used for
USB3.  Delete the USB3 COMPHY definition at platform level, and add
phy specifications for the ethernet channels.

Fixes: bd3d25b07342 ("arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
index bd4aab6092e0f..e31813a4f9722 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
@@ -143,6 +143,7 @@
 	phy-mode = "sgmii";
 	status = "okay";
 	managed = "in-band-status";
+	phys = <&comphy1 0>;
 	sfp = <&sfp_eth0>;
 };
 
@@ -150,11 +151,14 @@
 	phy-mode = "sgmii";
 	status = "okay";
 	managed = "in-band-status";
+	phys = <&comphy0 1>;
 	sfp = <&sfp_eth1>;
 };
 
 &usb3 {
 	status = "okay";
+	phys = <&usb2_utmi_otg_phy>;
+	phy-names = "usb2-utmi-otg-phy";
 };
 
 &uart0 {
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 159/459] arm64: dts: allwinner: H6: Add PMU mode
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (3 preceding siblings ...)
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 150/459] arm64: dts: uDPU: fix broken ethernet Sasha Levin
@ 2020-02-14 15:56 ` Sasha Levin
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 160/459] arm64: dts: allwinner: H5: Add PMU node Sasha Levin
                   ` (20 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:56 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Andre Przywara, Maxime Ripard, Sasha Levin, linux-arm-kernel, devicetree

From: Andre Przywara <andre.przywara@arm.com>

[ Upstream commit 7aa9b9eb7d6a8fde7acbe0446444f7e3fae1fe3b ]

Add the Performance Monitoring Unit (PMU) device tree node to the H6
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.

Tested with perf record and taskset on a Pine H64.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index 0d5ea19336a19..d192538916724 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -70,6 +70,16 @@
 		clock-output-names = "ext_osc32k";
 	};
 
+	pmu {
+		compatible = "arm,cortex-a53-pmu",
+			     "arm,armv8-pmuv3";
+		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	psci {
 		compatible = "arm,psci-0.2";
 		method = "smc";
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 160/459] arm64: dts: allwinner: H5: Add PMU node
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (4 preceding siblings ...)
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 159/459] arm64: dts: allwinner: H6: Add PMU mode Sasha Levin
@ 2020-02-14 15:56 ` Sasha Levin
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 161/459] arm: dts: allwinner: H3: " Sasha Levin
                   ` (19 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:56 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Andre Przywara, Maxime Ripard, Sasha Levin, linux-arm-kernel, devicetree

From: Andre Przywara <andre.przywara@arm.com>

[ Upstream commit c35a516a46187c8eeb7a56c64505ec6f7e22a0c7 ]

Add the Performance Monitoring Unit (PMU) device tree node to the H5
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core.
As with the A64, the interrupt numbers from the manual were wrong (off
by 4), the actual SPI IDs have been gathered in U-Boot, and were
verified with perf in Linux.

Tested with perf record and taskset on an OrangePi PC2.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
index f002a496d7cbb..1d34e3eefda3f 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -54,21 +54,21 @@
 			enable-method = "psci";
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <1>;
 			enable-method = "psci";
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <2>;
 			enable-method = "psci";
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <3>;
@@ -76,6 +76,16 @@
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a53-pmu",
+			     "arm,armv8-pmuv3";
+		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	psci {
 		compatible = "arm,psci-0.2";
 		method = "smc";
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 161/459] arm: dts: allwinner: H3: Add PMU node
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (5 preceding siblings ...)
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 160/459] arm64: dts: allwinner: H5: Add PMU node Sasha Levin
@ 2020-02-14 15:56 ` " Sasha Levin
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 163/459] ARM: dts: at91: Reenable UART TX pull-ups Sasha Levin
                   ` (18 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:56 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Andre Przywara, Maxime Ripard, Sasha Levin, devicetree, linux-arm-kernel

From: Andre Przywara <andre.przywara@arm.com>

[ Upstream commit 0388a110747bec0c9d9de995842bb2a03a26aae1 ]

Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.

Tested with perf record and taskset on an OrangePi Zero.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sun8i-h3.dtsi | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index e37c30e811d3b..6056f206c9e39 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -80,7 +80,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <1>;
@@ -90,7 +90,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <2>;
@@ -100,7 +100,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <3>;
@@ -111,6 +111,15 @@
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 163/459] ARM: dts: at91: Reenable UART TX pull-ups
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (6 preceding siblings ...)
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 161/459] arm: dts: allwinner: H3: " Sasha Levin
@ 2020-02-14 15:56 ` Sasha Levin
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 165/459] arm64: dts: qcom: msm8998: Fix tcsr syscon size Sasha Levin
                   ` (17 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:56 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Ingo van Lil, Peter Rosin, Alexandre Belloni, Sasha Levin,
	linux-arm-kernel, devicetree

From: Ingo van Lil <inguin@gmx.de>

[ Upstream commit 9d39d86cd4af2b17b970d63307daad71f563d207 ]

Pull-ups for SAM9 UART/USART TX lines were disabled in a previous
commit. However, several chips in the SAM9 family require pull-ups to
prevent the TX lines from falling (and causing an endless break
condition) when the transceiver is disabled.

From the SAM9G20 datasheet, 32.5.1: "To prevent the TXD line from
falling when the USART is disabled, the use of an internal pull up
is mandatory.". This commit reenables the pull-ups for all chips having
that sentence in their datasheets.

Fixes: 5e04822f7db5 ("ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on tx")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Cc: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20191203142147.875227-1-inguin@gmx.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/at91sam9260.dtsi | 12 ++++++------
 arch/arm/boot/dts/at91sam9261.dtsi |  6 +++---
 arch/arm/boot/dts/at91sam9263.dtsi |  6 +++---
 arch/arm/boot/dts/at91sam9g45.dtsi |  8 ++++----
 arch/arm/boot/dts/at91sam9rl.dtsi  |  8 ++++----
 5 files changed, 20 insertions(+), 20 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index dee9c0c8a0964..16c6fd3c42462 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -187,7 +187,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -221,7 +221,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -239,7 +239,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -257,7 +257,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -275,7 +275,7 @@
 				uart0 {
 					pinctrl_uart0: uart0-0 {
 						atmel,pins =
-							<AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_NONE
+							<AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP
 							 AT91_PIOA 30 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
 					};
 				};
@@ -283,7 +283,7 @@
 				uart1 {
 					pinctrl_uart1: uart1-0 {
 						atmel,pins =
-							<AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 				};
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index dba025a985270..5ed3d745ac867 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -329,7 +329,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -347,7 +347,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -365,7 +365,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index 99678abdda930..5c990cfae254e 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -183,7 +183,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -201,7 +201,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -219,7 +219,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 691c95ea61754..fd179097a4bfd 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -556,7 +556,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -574,7 +574,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -592,7 +592,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -610,7 +610,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+							<AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
 							 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 8643b71515650..ea024e4b6e095 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -682,7 +682,7 @@
 				usart0 {
 					pinctrl_usart0: usart0-0 {
 						atmel,pins =
-							<AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -721,7 +721,7 @@
 				usart1 {
 					pinctrl_usart1: usart1-0 {
 						atmel,pins =
-							<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -744,7 +744,7 @@
 				usart2 {
 					pinctrl_usart2: usart2-0 {
 						atmel,pins =
-							<AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
@@ -767,7 +767,7 @@
 				usart3 {
 					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+							<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
 							<AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
 					};
 
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 165/459] arm64: dts: qcom: msm8998: Fix tcsr syscon size
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (7 preceding siblings ...)
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 163/459] ARM: dts: at91: Reenable UART TX pull-ups Sasha Levin
@ 2020-02-14 15:56 ` Sasha Levin
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 167/459] arm64: dts: qcom: msm8996: Disable USB2 PHY suspend by core Sasha Levin
                   ` (16 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:56 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Jeffrey Hugo, Bjorn Andersson, Sasha Levin, linux-arm-msm, devicetree

From: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>

[ Upstream commit 05caa5bf9cab9983dd7a50428c46b7e617ba20d6 ]

The tcsr syscon region is really 0x40000 in size.  We need access to the
full region so that we can access the axi resets when managing the
modem subsystem.

Fixes: c7833949564e ("arm64: dts: qcom: msm8998: Add smem related nodes")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20191107045948.4341-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/msm8998.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index ffb64fc239ee5..ccd535edbf4e1 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -985,7 +985,7 @@
 
 		tcsr_mutex_regs: syscon@1f40000 {
 			compatible = "syscon";
-			reg = <0x01f40000 0x20000>;
+			reg = <0x01f40000 0x40000>;
 		};
 
 		tlmm: pinctrl@3400000 {
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 167/459] arm64: dts: qcom: msm8996: Disable USB2 PHY suspend by core
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (8 preceding siblings ...)
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 165/459] arm64: dts: qcom: msm8998: Fix tcsr syscon size Sasha Levin
@ 2020-02-14 15:56 ` Sasha Levin
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 173/459] ARM: dts: imx6: rdu2: Disable WP for USDHC2 and USDHC3 Sasha Levin
                   ` (15 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:56 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Manu Gautam, Paolo Pisati, Bjorn Andersson, Sasha Levin,
	linux-arm-msm, devicetree

From: Manu Gautam <mgautam@codeaurora.org>

[ Upstream commit d026c96b25b7ce5df89526aad2df988d553edb4d ]

QUSB2 PHY on msm8996 doesn't work well when autosuspend by
dwc3 core using USB2PHYCFG register is enabled. One of the
issue seen is that PHY driver reports PLL lock failure and
fails phy_init() if dwc3 core has USB2 PHY suspend enabled.
Fix this by using quirks to disable USB2 PHY LPM/suspend and
dwc3 core already takes care of explicitly suspending PHY
during suspend if quirks are specified.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Link: https://lore.kernel.org/r/20191209151501.26993-1-p.pisati@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 87f4d9c1b0d4c..fbb8ce78f95be 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1598,6 +1598,8 @@
 				interrupts = <0 138 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&hsusb_phy2>;
 				phy-names = "usb2-phy";
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
 			};
 		};
 
@@ -1628,6 +1630,8 @@
 				interrupts = <0 131 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&hsusb_phy1>, <&ssusb_phy_0>;
 				phy-names = "usb2-phy", "usb3-phy";
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
 			};
 		};
 
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 173/459] ARM: dts: imx6: rdu2: Disable WP for USDHC2 and USDHC3
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (9 preceding siblings ...)
  2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 167/459] arm64: dts: qcom: msm8996: Disable USB2 PHY suspend by core Sasha Levin
@ 2020-02-14 15:57 ` Sasha Levin
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 174/459] ARM: dts: imx6: rdu2: Limit USBH1 to Full Speed Sasha Levin
                   ` (14 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:57 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Andrey Smirnov, Chris Healy, Lucas Stach, Shawn Guo,
	Fabio Estevam, linux-arm-kernel, Sasha Levin, devicetree

From: Andrey Smirnov <andrew.smirnov@gmail.com>

[ Upstream commit cd58a174e58649426fb43d7456e5f7d7eab58af1 ]

RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".

Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
index 93be00a60c887..7b5c0e9b0fcff 100644
--- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
@@ -627,7 +627,7 @@
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+	disable-wp;
 	vmmc-supply = <&reg_3p3v_sd>;
 	vqmmc-supply = <&reg_3p3v>;
 	no-1-8-v;
@@ -640,7 +640,7 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+	disable-wp;
 	vmmc-supply = <&reg_3p3v_sd>;
 	vqmmc-supply = <&reg_3p3v>;
 	no-1-8-v;
@@ -1055,7 +1055,6 @@
 			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
 			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
 			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x40010040
 			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x40010040
 		>;
 	};
@@ -1068,7 +1067,6 @@
 			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
 			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
 			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x40010040
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x40010040
 
 		>;
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 174/459] ARM: dts: imx6: rdu2: Limit USBH1 to Full Speed
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (10 preceding siblings ...)
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 173/459] ARM: dts: imx6: rdu2: Disable WP for USDHC2 and USDHC3 Sasha Levin
@ 2020-02-14 15:57 ` Sasha Levin
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 214/459] ARM: dts: r8a7779: Add device node for ARM global timer Sasha Levin
                   ` (13 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:57 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Andrey Smirnov, Chris Healy, Lucas Stach, Shawn Guo,
	Fabio Estevam, linux-arm-kernel, Sasha Levin, devicetree

From: Andrey Smirnov <andrew.smirnov@gmail.com>

[ Upstream commit 6bb1e09c4c375db29770444f689f35f5cbe696bc ]

Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.

Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
index 7b5c0e9b0fcff..a66c4fac6baf0 100644
--- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
@@ -774,6 +774,7 @@
 &usbh1 {
 	vbus-supply = <&reg_5p0v_main>;
 	disable-over-current;
+	maximum-speed = "full-speed";
 	status = "okay";
 };
 
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 214/459] ARM: dts: r8a7779: Add device node for ARM global timer
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (11 preceding siblings ...)
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 174/459] ARM: dts: imx6: rdu2: Limit USBH1 to Full Speed Sasha Levin
@ 2020-02-14 15:57 ` Sasha Levin
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 215/459] arm64: dts: renesas: r8a77990: ebisu: Remove clkout-lr-synchronous from sound Sasha Levin
                   ` (12 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:57 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Geert Uytterhoeven, Sasha Levin, linux-renesas-soc, devicetree

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 8443ffd1bbd5be74e9b12db234746d12e8ea93e2 ]

Add a device node for the global timer, which is part of the Cortex-A9
MPCore.

The global timer can serve as an accurate (4 ns) clock source for
scheduling and delay loops.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191211135222.26770-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/r8a7779.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/r8a7779.dtsi
index ebf5b7cfe2159..63341635bddf8 100644
--- a/arch/arm/boot/dts/r8a7779.dtsi
+++ b/arch/arm/boot/dts/r8a7779.dtsi
@@ -68,6 +68,14 @@
 		      <0xf0000100 0x100>;
 	};
 
+	timer@f0000200 {
+		compatible = "arm,cortex-a9-global-timer";
+		reg = <0xf0000200 0x100>;
+		interrupts = <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
+		clocks = <&cpg_clocks R8A7779_CLK_ZS>;
+	};
+
 	timer@f0000600 {
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0xf0000600 0x20>;
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 215/459] arm64: dts: renesas: r8a77990: ebisu: Remove clkout-lr-synchronous from sound
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (12 preceding siblings ...)
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 214/459] ARM: dts: r8a7779: Add device node for ARM global timer Sasha Levin
@ 2020-02-14 15:57 ` Sasha Levin
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 218/459] arm64: dts: qcom: db845c: Enable ath10k 8bit host-cap quirk Sasha Levin
                   ` (11 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:57 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Kuninori Morimoto, Geert Uytterhoeven, Sasha Levin,
	linux-renesas-soc, devicetree

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

[ Upstream commit bf2b74ce9b33a2edd6ba1930ce60a71830790910 ]

rcar_sound doesn't support clkout-lr-synchronous in upstream.
It was supported under out-of-tree rcar_sound.
upstream rcar_sound is supporting
	- clkout-lr-synchronous
	+ clkout-lr-asynchronous

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mubt3tux.wl-kuninori.morimoto.gx@renesas.com
Fixes: 56629fcba94c698d ("arm64: dts: renesas: ebisu: Enable Audio")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
index b38f9d442fc08..e6d700f8c1948 100644
--- a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
@@ -636,7 +636,6 @@
 	/* audio_clkout0/1/2/3 */
 	#clock-cells = <1>;
 	clock-frequency = <12288000 11289600>;
-	clkout-lr-synchronous;
 
 	status = "okay";
 
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 218/459] arm64: dts: qcom: db845c: Enable ath10k 8bit host-cap quirk
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (13 preceding siblings ...)
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 215/459] arm64: dts: renesas: r8a77990: ebisu: Remove clkout-lr-synchronous from sound Sasha Levin
@ 2020-02-14 15:57 ` Sasha Levin
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 261/459] ARM: dts: meson8: use the actual frequency for the GPU's 182.1MHz OPP Sasha Levin
                   ` (10 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:57 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Bjorn Andersson, Jeffrey Hugo, Sasha Levin, linux-arm-msm, devicetree

From: Bjorn Andersson <bjorn.andersson@linaro.org>

[ Upstream commit 2e198c395a084ff3015d71896e35de049c40e3a4 ]

The WiFi firmware used on db845c implements the 8bit host-capability
message, so enable the quirk for this.

Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20191113232245.4039932-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index f5a85caff1a39..751651a6cd819 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -517,6 +517,8 @@
 	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+
+	qcom,snoc-host-cap-8bit-quirk;
 };
 
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 261/459] ARM: dts: meson8: use the actual frequency for the GPU's 182.1MHz OPP
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (14 preceding siblings ...)
  2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 218/459] arm64: dts: qcom: db845c: Enable ath10k 8bit host-cap quirk Sasha Levin
@ 2020-02-14 15:58 ` Sasha Levin
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 262/459] ARM: dts: meson8b: use the actual frequency for the GPU's 364MHz OPP Sasha Levin
                   ` (9 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:58 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Martin Blumenstingl, Kevin Hilman, Sasha Levin, devicetree,
	linux-arm-kernel, linux-amlogic

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit fe634a7a9a57fb736e39fb71aa9adc6448a90f94 ]

The clock setup on Meson8 cannot achieve a Mali frequency of exactly
182.15MHz. The vendor driver uses "FCLK_DIV7 / 2" for this frequency,
which translates to 2550MHz / 7 / 2 = 182142857Hz.
Update the GPU operating point to that specific frequency to not confuse
myself when comparing the frequency from the .dts with the actual clock
rate on the system.

Fixes: 7d3f6b536e72c9 ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/meson8.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
index 3c534cd50ee3b..db2033f674c67 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -129,8 +129,8 @@
 	gpu_opp_table: gpu-opp-table {
 		compatible = "operating-points-v2";
 
-		opp-182150000 {
-			opp-hz = /bits/ 64 <182150000>;
+		opp-182142857 {
+			opp-hz = /bits/ 64 <182142857>;
 			opp-microvolt = <1150000>;
 		};
 		opp-318750000 {
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 262/459] ARM: dts: meson8b: use the actual frequency for the GPU's 364MHz OPP
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (15 preceding siblings ...)
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 261/459] ARM: dts: meson8: use the actual frequency for the GPU's 182.1MHz OPP Sasha Levin
@ 2020-02-14 15:58 ` Sasha Levin
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 267/459] ARM: dts: stm32: Add power-supply for DSI panel on stm32f469-disco Sasha Levin
                   ` (8 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:58 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Martin Blumenstingl, Kevin Hilman, Sasha Levin, devicetree,
	linux-arm-kernel, linux-amlogic

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

[ Upstream commit c3dd3315ab58b2cfa1916df55b0d0f9fbd94266f ]

The clock setup on Meson8 cannot achieve a Mali frequency of exactly
182.15MHz. The vendor driver uses "FCLK_DIV7 / 1" for this frequency,
which translates to 2550MHz / 7 / 1 = 364285714Hz.
Update the GPU operating point to that specific frequency to not confuse
myself when comparing the frequency from the .dts with the actual clock
rate on the system.

Fixes: c3ea80b6138cae ("ARM: dts: meson8b: add the Mali-450 MP2 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/meson8b.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi
index 099bf8e711c94..1e8c5d7bc824a 100644
--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/meson8b.dtsi
@@ -125,8 +125,8 @@
 			opp-hz = /bits/ 64 <255000000>;
 			opp-microvolt = <1100000>;
 		};
-		opp-364300000 {
-			opp-hz = /bits/ 64 <364300000>;
+		opp-364285714 {
+			opp-hz = /bits/ 64 <364285714>;
 			opp-microvolt = <1100000>;
 		};
 		opp-425000000 {
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 267/459] ARM: dts: stm32: Add power-supply for DSI panel on stm32f469-disco
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (16 preceding siblings ...)
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 262/459] ARM: dts: meson8b: use the actual frequency for the GPU's 364MHz OPP Sasha Levin
@ 2020-02-14 15:58 ` Sasha Levin
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 277/459] ARM: dts: at91: sama5d3: fix maximum peripheral clock rates Sasha Levin
                   ` (7 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:58 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Benjamin Gaignard, Alexandre Torgue, Sasha Levin, linux-stm32,
	linux-arm-kernel, devicetree

From: Benjamin Gaignard <benjamin.gaignard@st.com>

[ Upstream commit 0ff15a86d0c5a3f004fee2e92d65b88e56a3bc58 ]

Add a fixed regulator and use it as power supply for DSI panel.

Fixes: 18c8866266 ("ARM: dts: stm32: Add display support on stm32f469-disco")

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32f469-disco.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/stm32f469-disco.dts b/arch/arm/boot/dts/stm32f469-disco.dts
index a3ff04940aec1..c6dc6d1a051b0 100644
--- a/arch/arm/boot/dts/stm32f469-disco.dts
+++ b/arch/arm/boot/dts/stm32f469-disco.dts
@@ -76,6 +76,13 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
+	vdd_dsi: vdd-dsi {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_dsi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	soc {
 		dma-ranges = <0xc0000000 0x0 0x10000000>;
 	};
@@ -155,6 +162,7 @@
 		compatible = "orisetech,otm8009a";
 		reg = <0>; /* dsi virtual channel (0..3) */
 		reset-gpios = <&gpioh 7 GPIO_ACTIVE_LOW>;
+		power-supply = <&vdd_dsi>;
 		status = "okay";
 
 		port {
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 277/459] ARM: dts: at91: sama5d3: fix maximum peripheral clock rates
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (17 preceding siblings ...)
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 267/459] ARM: dts: stm32: Add power-supply for DSI panel on stm32f469-disco Sasha Levin
@ 2020-02-14 15:58 ` Sasha Levin
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 278/459] ARM: dts: at91: sama5d3: define clock rate range for tcb1 Sasha Levin
                   ` (6 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:58 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Alexandre Belloni, Karl Rudbæk Olsen, Sasha Levin,
	linux-arm-kernel, devicetree

From: Alexandre Belloni <alexandre.belloni@bootlin.com>

[ Upstream commit ee0aa926ddb0bd8ba59e33e3803b3b5804e3f5da ]

Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.

Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sama5d3.dtsi      | 28 ++++++++++++++--------------
 arch/arm/boot/dts/sama5d3_can.dtsi  |  4 ++--
 arch/arm/boot/dts/sama5d3_uart.dtsi |  4 ++--
 3 files changed, 18 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index f770aace0efd6..203d40be70a51 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -1188,49 +1188,49 @@
 					usart0_clk: usart0_clk {
 						#clock-cells = <0>;
 						reg = <12>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					usart1_clk: usart1_clk {
 						#clock-cells = <0>;
 						reg = <13>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					usart2_clk: usart2_clk {
 						#clock-cells = <0>;
 						reg = <14>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					usart3_clk: usart3_clk {
 						#clock-cells = <0>;
 						reg = <15>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					uart0_clk: uart0_clk {
 						#clock-cells = <0>;
 						reg = <16>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					twi0_clk: twi0_clk {
 						reg = <18>;
 						#clock-cells = <0>;
-						atmel,clk-output-range = <0 16625000>;
+						atmel,clk-output-range = <0 41500000>;
 					};
 
 					twi1_clk: twi1_clk {
 						#clock-cells = <0>;
 						reg = <19>;
-						atmel,clk-output-range = <0 16625000>;
+						atmel,clk-output-range = <0 41500000>;
 					};
 
 					twi2_clk: twi2_clk {
 						#clock-cells = <0>;
 						reg = <20>;
-						atmel,clk-output-range = <0 16625000>;
+						atmel,clk-output-range = <0 41500000>;
 					};
 
 					mci0_clk: mci0_clk {
@@ -1246,19 +1246,19 @@
 					spi0_clk: spi0_clk {
 						#clock-cells = <0>;
 						reg = <24>;
-						atmel,clk-output-range = <0 133000000>;
+						atmel,clk-output-range = <0 166000000>;
 					};
 
 					spi1_clk: spi1_clk {
 						#clock-cells = <0>;
 						reg = <25>;
-						atmel,clk-output-range = <0 133000000>;
+						atmel,clk-output-range = <0 166000000>;
 					};
 
 					tcb0_clk: tcb0_clk {
 						#clock-cells = <0>;
 						reg = <26>;
-						atmel,clk-output-range = <0 133000000>;
+						atmel,clk-output-range = <0 166000000>;
 					};
 
 					pwm_clk: pwm_clk {
@@ -1269,7 +1269,7 @@
 					adc_clk: adc_clk {
 						#clock-cells = <0>;
 						reg = <29>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					dma0_clk: dma0_clk {
@@ -1300,13 +1300,13 @@
 					ssc0_clk: ssc0_clk {
 						#clock-cells = <0>;
 						reg = <38>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					ssc1_clk: ssc1_clk {
 						#clock-cells = <0>;
 						reg = <39>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					sha_clk: sha_clk {
diff --git a/arch/arm/boot/dts/sama5d3_can.dtsi b/arch/arm/boot/dts/sama5d3_can.dtsi
index cf06a018ed0f2..2470dd3fff25e 100644
--- a/arch/arm/boot/dts/sama5d3_can.dtsi
+++ b/arch/arm/boot/dts/sama5d3_can.dtsi
@@ -36,13 +36,13 @@
 					can0_clk: can0_clk {
 						#clock-cells = <0>;
 						reg = <40>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					can1_clk: can1_clk {
 						#clock-cells = <0>;
 						reg = <41>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 				};
 			};
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index 4316bdbdc25dd..cb62adbd28ed6 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -41,13 +41,13 @@
 					uart0_clk: uart0_clk {
 						#clock-cells = <0>;
 						reg = <16>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					uart1_clk: uart1_clk {
 						#clock-cells = <0>;
 						reg = <17>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 				};
 			};
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 278/459] ARM: dts: at91: sama5d3: define clock rate range for tcb1
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (18 preceding siblings ...)
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 277/459] ARM: dts: at91: sama5d3: fix maximum peripheral clock rates Sasha Levin
@ 2020-02-14 15:58 ` Sasha Levin
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 288/459] arm64: dts: rockchip: fix dwmmc clock name for px30 Sasha Levin
                   ` (5 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:58 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Alexandre Belloni, Karl Rudbæk Olsen, Sasha Levin,
	linux-arm-kernel, devicetree

From: Alexandre Belloni <alexandre.belloni@bootlin.com>

[ Upstream commit a7e0f3fc01df4b1b7077df777c37feae8c9e8b6d ]

The clock rate range for the TCB1 clock is missing. define it in the device
tree.

Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sama5d3_tcb1.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
index 1584035daf515..215802b8db301 100644
--- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi
+++ b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
@@ -22,6 +22,7 @@
 					tcb1_clk: tcb1_clk {
 						#clock-cells = <0>;
 						reg = <27>;
+						atmel,clk-output-range = <0 166000000>;
 					};
 				};
 			};
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 288/459] arm64: dts: rockchip: fix dwmmc clock name for px30
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (19 preceding siblings ...)
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 278/459] ARM: dts: at91: sama5d3: define clock rate range for tcb1 Sasha Levin
@ 2020-02-14 15:58 ` Sasha Levin
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 289/459] arm64: dts: rockchip: add reg property to brcmf sub-nodes Sasha Levin
                   ` (4 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:58 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Johan Jonker, Heiko Stuebner, Sasha Levin, devicetree,
	linux-arm-kernel, linux-rockchip

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit 7f2147350291569acd1df5a26dcdfc573916016f ]

An experimental test with the command below gives this error:
px30-evb.dt.yaml: dwmmc@ff390000: clock-names:2:
'ciu-drive' was expected

'ciu-drv' is not a valid dwmmc clock name,
so fix this by changing it to 'ciu-drive'.

make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110161200.22755-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/px30.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/px30.dtsi b/arch/arm64/boot/dts/rockchip/px30.dtsi
index eb992d60e6baf..9e09909a510a1 100644
--- a/arch/arm64/boot/dts/rockchip/px30.dtsi
+++ b/arch/arm64/boot/dts/rockchip/px30.dtsi
@@ -768,7 +768,7 @@
 		interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
 			 <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
-		clock-names = "biu", "ciu", "ciu-drv", "ciu-sample";
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
 		fifo-depth = <0x100>;
 		max-frequency = <150000000>;
 		pinctrl-names = "default";
@@ -783,7 +783,7 @@
 		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
 			 <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
-		clock-names = "biu", "ciu", "ciu-drv", "ciu-sample";
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
 		fifo-depth = <0x100>;
 		max-frequency = <150000000>;
 		pinctrl-names = "default";
@@ -798,7 +798,7 @@
 		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
 			 <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
-		clock-names = "biu", "ciu", "ciu-drv", "ciu-sample";
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
 		fifo-depth = <0x100>;
 		max-frequency = <150000000>;
 		power-domains = <&power PX30_PD_MMC_NAND>;
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 289/459] arm64: dts: rockchip: add reg property to brcmf sub-nodes
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (20 preceding siblings ...)
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 288/459] arm64: dts: rockchip: fix dwmmc clock name for px30 Sasha Levin
@ 2020-02-14 15:58 ` Sasha Levin
  2020-02-14 15:59 ` [PATCH AUTOSEL 5.4 290/459] ARM: dts: rockchip: add reg property to brcmf sub node for rk3188-bqedison2qc Sasha Levin
                   ` (3 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:58 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Johan Jonker, Heiko Stuebner, Sasha Levin, devicetree,
	linux-arm-kernel, linux-rockchip

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit 96ff264bccb22175bbe2185a1eb5204ca3c5f03f ]

An experimental test with the command below gives this error:
rk3399-firefly.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-orangepi.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge-captain.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge-v.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
So fix this by adding a reg property to the brcmf sub node.
Also add #address-cells and #size-cells to prevent more warnings.

make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110142128.13522-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3399-firefly.dts      | 3 +++
 arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi | 3 +++
 arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts     | 3 +++
 3 files changed, 9 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
index c706db0ee9ec6..76f5db696009b 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
@@ -669,9 +669,12 @@
 	vqmmc-supply = &vcc1v8_s3;	/* IO line */
 	vmmc-supply = &vcc_sdio;	/* card's power */
 
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
 
 	brcmf: wifi@1 {
+		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
index 4944d78a0a1cb..e87a04477440e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
@@ -654,9 +654,12 @@
 	sd-uhs-sdr104;
 	vqmmc-supply = <&vcc1v8_s3>;
 	vmmc-supply = <&vccio_sd>;
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
 
 	brcmf: wifi@1 {
+		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts b/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts
index 0541dfce924d6..9c659f3115c88 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts
@@ -648,9 +648,12 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
 	sd-uhs-sdr104;
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
 
 	brcmf: wifi@1 {
+		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 290/459] ARM: dts: rockchip: add reg property to brcmf sub node for rk3188-bqedison2qc
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (21 preceding siblings ...)
  2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 289/459] arm64: dts: rockchip: add reg property to brcmf sub-nodes Sasha Levin
@ 2020-02-14 15:59 ` Sasha Levin
  2020-02-14 15:59 ` [PATCH AUTOSEL 5.4 304/459] ARC: [plat-axs10x]: Add missing multicast filter number to GMAC node Sasha Levin
                   ` (2 subsequent siblings)
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:59 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Johan Jonker, Heiko Stuebner, Sasha Levin, linux-arm-kernel,
	linux-rockchip, devicetree

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit cf206bca178cd5b5a436494b2e0cea75295944f4 ]

An experimental test with the command below gives this error:
rk3188-bqedison2qc.dt.yaml: dwmmc@10218000: wifi@1:
'reg' is a required property

So fix this by adding a reg property to the brcmf sub node.
Also add #address-cells and #size-cells to prevent more warnings.

make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110134420.11280-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3188-bqedison2qc.dts | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/rk3188-bqedison2qc.dts b/arch/arm/boot/dts/rk3188-bqedison2qc.dts
index c8b62bbd6a4a4..ad1afd403052a 100644
--- a/arch/arm/boot/dts/rk3188-bqedison2qc.dts
+++ b/arch/arm/boot/dts/rk3188-bqedison2qc.dts
@@ -466,9 +466,12 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd1_clk>, <&sd1_cmd>, <&sd1_bus4>;
 	vmmcq-supply = <&vccio_wl>;
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
 
 	brcmf: wifi@1 {
+		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio3>;
 		interrupts = <RK_PD2 GPIO_ACTIVE_HIGH>;
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 304/459] ARC: [plat-axs10x]: Add missing multicast filter number to GMAC node
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (22 preceding siblings ...)
  2020-02-14 15:59 ` [PATCH AUTOSEL 5.4 290/459] ARM: dts: rockchip: add reg property to brcmf sub node for rk3188-bqedison2qc Sasha Levin
@ 2020-02-14 15:59 ` Sasha Levin
  2020-02-14 15:59 ` [PATCH AUTOSEL 5.4 342/459] arm64: dts: ti: k3-j721e-main: Add missing power-domains for smmu Sasha Levin
  2020-02-14 16:00 ` [PATCH AUTOSEL 5.4 387/459] ARM: dts: am43xx: add support for clkout1 clock Sasha Levin
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:59 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Jose Abreu, Alexey Brodkin, Vineet Gupta, Sasha Levin,
	devicetree, linux-snps-arc

From: Jose Abreu <Jose.Abreu@synopsys.com>

[ Upstream commit 7980dff398f86a618f502378fa27cf7e77449afa ]

Add a missing property to GMAC node so that multicast filtering works
correctly.

Fixes: 556cc1c5f528 ("ARC: [axs101] Add support for AXS101 SDP (software development platform)")
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arc/boot/dts/axs10x_mb.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arc/boot/dts/axs10x_mb.dtsi b/arch/arc/boot/dts/axs10x_mb.dtsi
index 08bcfed6b80f5..134cc223ea81b 100644
--- a/arch/arc/boot/dts/axs10x_mb.dtsi
+++ b/arch/arc/boot/dts/axs10x_mb.dtsi
@@ -77,6 +77,7 @@
 			interrupt-names = "macirq";
 			phy-mode = "rgmii";
 			snps,pbl = < 32 >;
+			snps,multicast-filter-bins = <256>;
 			clocks = <&apbclk>;
 			clock-names = "stmmaceth";
 			max-speed = <100>;
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 342/459] arm64: dts: ti: k3-j721e-main: Add missing power-domains for smmu
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (23 preceding siblings ...)
  2020-02-14 15:59 ` [PATCH AUTOSEL 5.4 304/459] ARC: [plat-axs10x]: Add missing multicast filter number to GMAC node Sasha Levin
@ 2020-02-14 15:59 ` Sasha Levin
  2020-02-14 16:00 ` [PATCH AUTOSEL 5.4 387/459] ARM: dts: am43xx: add support for clkout1 clock Sasha Levin
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 15:59 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Lokesh Vutla, Suman Anna, Tero Kristo, Sasha Levin,
	linux-arm-kernel, devicetree

From: Lokesh Vutla <lokeshvutla@ti.com>

[ Upstream commit 3f03a58b25753843ce9e4511e9e246c51bd11011 ]

Add power-domains entry for smmu, so that the it is accessible as long
as the driver is active. Without this device shutdown is throwing the
below warning:
"[   44.736348] arm-smmu-v3 36600000.smmu: failed to clear cr0"

Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 698ef9a1d5b75..96445111e3985 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -43,6 +43,7 @@
 	smmu0: smmu@36600000 {
 		compatible = "arm,smmu-v3";
 		reg = <0x0 0x36600000 0x0 0x100000>;
+		power-domains = <&k3_pds 229 TI_SCI_PD_EXCLUSIVE>;
 		interrupt-parent = <&gic500>;
 		interrupts = <GIC_SPI 772 IRQ_TYPE_EDGE_RISING>,
 			     <GIC_SPI 768 IRQ_TYPE_EDGE_RISING>;
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

* [PATCH AUTOSEL 5.4 387/459] ARM: dts: am43xx: add support for clkout1 clock
       [not found] <20200214160149.11681-1-sashal@kernel.org>
                   ` (24 preceding siblings ...)
  2020-02-14 15:59 ` [PATCH AUTOSEL 5.4 342/459] arm64: dts: ti: k3-j721e-main: Add missing power-domains for smmu Sasha Levin
@ 2020-02-14 16:00 ` Sasha Levin
  25 siblings, 0 replies; 26+ messages in thread
From: Sasha Levin @ 2020-02-14 16:00 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Tero Kristo, Benoit Parrot, Tony Lindgren, Sasha Levin,
	linux-omap, devicetree

From: Tero Kristo <t-kristo@ti.com>

[ Upstream commit 01053dadb79d63b65f7b353e68b4b6ccf4effedb ]

clkout1 clock node and its generation tree was missing. Add this based
on the data on TRM and PRCM functional spec.

commit 664ae1ab2536 ("ARM: dts: am43xx: add clkctrl nodes") effectively
reverted this commit 8010f13a40d3 ("ARM: dts: am43xx: add support for
clkout1 clock") which is needed for the ov2659 camera sensor clock
definition hence it is being re-applied here.

Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "clkout1-*ck" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.

Fixes: 664ae1ab2536 ("ARM: dts: am43xx: add clkctrl nodes")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/am43xx-clocks.dtsi | 54 ++++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm/boot/dts/am43xx-clocks.dtsi b/arch/arm/boot/dts/am43xx-clocks.dtsi
index 091356f2a8c16..c726cd8dbdf1b 100644
--- a/arch/arm/boot/dts/am43xx-clocks.dtsi
+++ b/arch/arm/boot/dts/am43xx-clocks.dtsi
@@ -704,6 +704,60 @@
 		ti,bit-shift = <8>;
 		reg = <0x2a48>;
 	};
+
+	clkout1_osc_div_ck: clkout1-osc-div-ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&sys_clkin_ck>;
+		ti,bit-shift = <20>;
+		ti,max-div = <4>;
+		reg = <0x4100>;
+	};
+
+	clkout1_src2_mux_ck: clkout1-src2-mux-ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&clk_rc32k_ck>, <&sysclk_div>, <&dpll_ddr_m2_ck>,
+			 <&dpll_per_m2_ck>, <&dpll_disp_m2_ck>,
+			 <&dpll_mpu_m2_ck>;
+		reg = <0x4100>;
+	};
+
+	clkout1_src2_pre_div_ck: clkout1-src2-pre-div-ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&clkout1_src2_mux_ck>;
+		ti,bit-shift = <4>;
+		ti,max-div = <8>;
+		reg = <0x4100>;
+	};
+
+	clkout1_src2_post_div_ck: clkout1-src2-post-div-ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&clkout1_src2_pre_div_ck>;
+		ti,bit-shift = <8>;
+		ti,max-div = <32>;
+		ti,index-power-of-two;
+		reg = <0x4100>;
+	};
+
+	clkout1_mux_ck: clkout1-mux-ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&clkout1_osc_div_ck>, <&clk_rc32k_ck>,
+			 <&clkout1_src2_post_div_ck>, <&dpll_extdev_m2_ck>;
+		ti,bit-shift = <16>;
+		reg = <0x4100>;
+	};
+
+	clkout1_ck: clkout1-ck {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkout1_mux_ck>;
+		ti,bit-shift = <23>;
+		reg = <0x4100>;
+	};
 };
 
 &prcm {
-- 
2.20.1


^ permalink raw reply	[flat|nested] 26+ messages in thread

end of thread, back to index

Thread overview: 26+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
     [not found] <20200214160149.11681-1-sashal@kernel.org>
2020-02-14 15:55 ` [PATCH AUTOSEL 5.4 050/459] arm64: dts: marvell: clearfog-gt-8k: fix switch cpu port node Sasha Levin
2020-02-14 15:55 ` [PATCH AUTOSEL 5.4 063/459] dt-bindings: iio: adc: ad7606: Fix wrong maxItems value Sasha Levin
2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 148/459] arm64: dts: rockchip: Fix NanoPC-T4 cooling maps Sasha Levin
2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 150/459] arm64: dts: uDPU: fix broken ethernet Sasha Levin
2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 159/459] arm64: dts: allwinner: H6: Add PMU mode Sasha Levin
2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 160/459] arm64: dts: allwinner: H5: Add PMU node Sasha Levin
2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 161/459] arm: dts: allwinner: H3: " Sasha Levin
2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 163/459] ARM: dts: at91: Reenable UART TX pull-ups Sasha Levin
2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 165/459] arm64: dts: qcom: msm8998: Fix tcsr syscon size Sasha Levin
2020-02-14 15:56 ` [PATCH AUTOSEL 5.4 167/459] arm64: dts: qcom: msm8996: Disable USB2 PHY suspend by core Sasha Levin
2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 173/459] ARM: dts: imx6: rdu2: Disable WP for USDHC2 and USDHC3 Sasha Levin
2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 174/459] ARM: dts: imx6: rdu2: Limit USBH1 to Full Speed Sasha Levin
2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 214/459] ARM: dts: r8a7779: Add device node for ARM global timer Sasha Levin
2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 215/459] arm64: dts: renesas: r8a77990: ebisu: Remove clkout-lr-synchronous from sound Sasha Levin
2020-02-14 15:57 ` [PATCH AUTOSEL 5.4 218/459] arm64: dts: qcom: db845c: Enable ath10k 8bit host-cap quirk Sasha Levin
2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 261/459] ARM: dts: meson8: use the actual frequency for the GPU's 182.1MHz OPP Sasha Levin
2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 262/459] ARM: dts: meson8b: use the actual frequency for the GPU's 364MHz OPP Sasha Levin
2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 267/459] ARM: dts: stm32: Add power-supply for DSI panel on stm32f469-disco Sasha Levin
2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 277/459] ARM: dts: at91: sama5d3: fix maximum peripheral clock rates Sasha Levin
2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 278/459] ARM: dts: at91: sama5d3: define clock rate range for tcb1 Sasha Levin
2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 288/459] arm64: dts: rockchip: fix dwmmc clock name for px30 Sasha Levin
2020-02-14 15:58 ` [PATCH AUTOSEL 5.4 289/459] arm64: dts: rockchip: add reg property to brcmf sub-nodes Sasha Levin
2020-02-14 15:59 ` [PATCH AUTOSEL 5.4 290/459] ARM: dts: rockchip: add reg property to brcmf sub node for rk3188-bqedison2qc Sasha Levin
2020-02-14 15:59 ` [PATCH AUTOSEL 5.4 304/459] ARC: [plat-axs10x]: Add missing multicast filter number to GMAC node Sasha Levin
2020-02-14 15:59 ` [PATCH AUTOSEL 5.4 342/459] arm64: dts: ti: k3-j721e-main: Add missing power-domains for smmu Sasha Levin
2020-02-14 16:00 ` [PATCH AUTOSEL 5.4 387/459] ARM: dts: am43xx: add support for clkout1 clock Sasha Levin

Linux-Devicetree Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-devicetree/0 linux-devicetree/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-devicetree linux-devicetree/ https://lore.kernel.org/linux-devicetree \
		devicetree@vger.kernel.org
	public-inbox-index linux-devicetree

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-devicetree


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git