[PATCH 00/12] irqchip: ti,sci-intr/inta: Update the dt bindings to accept different interrupt parents

[PATCH 00/12] irqchip: ti,sci-intr/inta: Update the dt bindings to accept different interrupt parents

[Lokesh Vutla]

Hi Marc,
	This is continuation of the RFC patches[0] regarding the driver
updates to support for following interrupt parent connection:
- INTR -> INTR
- INTA -> GICv3
The current existing driver assumes that INTR is always connected to
GICv3 and INTA is always connected to INTR.

As discussed this change breaks the DT backward compatibility but it
allows to not depend on TISCI firmware properties in DT node. IMHO, this
will ensure that any future changes will not effect DT properties.

[0] https://lore.kernel.org/linux-arm-kernel/20190923042405.26064-1-lokeshvutla@ti.com/

Thanks and regards,
Lokesh

Lokesh Vutla (12):
  firmware: ti_sci: Drop the device id to resource type translation
  firmware: ti_sci: Drop unused structure ti_sci_rm_type_map
  firmware: ti_sci: Add support for getting resource with subtype
  dt-bindings: irqchip: ti,sci-intr: Update bindings to drop the usage
    of gic as parent
  dt-bindings: irqchip: Convert ti,sci-intr bindings to yaml
  irqchip/ti-sci-intr: Add support for INTR being a parent to INTR
  dt-bindings: irqchip: ti,sci-inta: Update docs to support different
    parent.
  dt-bindings: irqchip: Convert ti,sci-inta bindings to yaml
  irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC
  arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings
  arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings
  arm64: dts: k3-am65: Update the RM resource types

 .../interrupt-controller/ti,sci-inta.txt      |  66 --------
 .../interrupt-controller/ti,sci-inta.yaml     | 104 ++++++++++++
 .../interrupt-controller/ti,sci-intr.txt      |  82 ---------
 .../interrupt-controller/ti,sci-intr.yaml     | 113 +++++++++++++
 MAINTAINERS                                   |   4 +-
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi      |  34 ++--
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi       |  12 +-
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi    |   8 +-
 .../arm64/boot/dts/ti/k3-am654-base-board.dts |   4 +-
 .../dts/ti/k3-j721e-common-proc-board.dts     |  10 +-
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi     |  41 ++---
 .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi      |  12 +-
 drivers/firmware/ti_sci.c                     | 155 ++++++++----------
 drivers/irqchip/irq-ti-sci-inta.c             |  90 ++++++++--
 drivers/irqchip/irq-ti-sci-intr.c             | 150 ++++++++++-------
 include/linux/soc/ti/ti_sci_protocol.h        |  13 ++
 16 files changed, 527 insertions(+), 371 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.yaml
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml

-- 
2.17.1

[PATCH 01/12] firmware: ti_sci: Drop the device id to resource type translation

[Lokesh Vutla]

With ABI 3.0, sysfw deprecated special resource types used for AM65x
SoC. Instead started using device id as resource type similar to the
convention used in J721E SOC.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 drivers/firmware/ti_sci.c | 12 +-----------
 1 file changed, 1 insertion(+), 11 deletions(-)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 4126be9e3216..930a65ed78ad 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -3355,16 +3355,6 @@ static const struct ti_sci_desc ti_sci_pmmc_k2g_desc = {
 	.rm_type_map = NULL,
 };
 
-static struct ti_sci_rm_type_map ti_sci_am654_rm_type_map[] = {
-	{.dev_id = 56, .type = 0x00b}, /* GIC_IRQ */
-	{.dev_id = 179, .type = 0x000}, /* MAIN_NAV_UDMASS_IA0 */
-	{.dev_id = 187, .type = 0x009}, /* MAIN_NAV_RA */
-	{.dev_id = 188, .type = 0x006}, /* MAIN_NAV_UDMAP */
-	{.dev_id = 194, .type = 0x007}, /* MCU_NAV_UDMAP */
-	{.dev_id = 195, .type = 0x00a}, /* MCU_NAV_RA */
-	{.dev_id = 0, .type = 0x000}, /* end of table */
-};
-
 /* Description for AM654 */
 static const struct ti_sci_desc ti_sci_pmmc_am654_desc = {
 	.default_host_id = 12,
@@ -3373,7 +3363,7 @@ static const struct ti_sci_desc ti_sci_pmmc_am654_desc = {
 	/* Limited by MBOX_TX_QUEUE_LEN. K2G can handle upto 128 messages! */
 	.max_msgs = 20,
 	.max_msg_size = 60,
-	.rm_type_map = ti_sci_am654_rm_type_map,
+	.rm_type_map = NULL,
 };
 
 static const struct of_device_id ti_sci_of_match[] = {
-- 
2.17.1

[PATCH 02/12] firmware: ti_sci: Drop unused structure ti_sci_rm_type_map

[Lokesh Vutla]

struct ti_sci_rm_type_map is no longer used. Drop its definition and its
declarations.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 drivers/firmware/ti_sci.c | 56 +--------------------------------------
 1 file changed, 1 insertion(+), 55 deletions(-)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 930a65ed78ad..a81ddec9e669 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -64,22 +64,6 @@ struct ti_sci_xfers_info {
 	spinlock_t xfer_lock;
 };
 
-/**
- * struct ti_sci_rm_type_map - Structure representing TISCI Resource
- *				management representation of dev_ids.
- * @dev_id:	TISCI device ID
- * @type:	Corresponding id as identified by TISCI RM.
- *
- * Note: This is used only as a work around for using RM range apis
- *	for AM654 SoC. For future SoCs dev_id will be used as type
- *	for RM range APIs. In order to maintain ABI backward compatibility
- *	type is not being changed for AM654 SoC.
- */
-struct ti_sci_rm_type_map {
-	u32 dev_id;
-	u16 type;
-};
-
 /**
  * struct ti_sci_desc - Description of SoC integration
  * @default_host_id:	Host identifier representing the compute entity
@@ -87,14 +71,12 @@ struct ti_sci_rm_type_map {
  * @max_msgs: Maximum number of messages that can be pending
  *		  simultaneously in the system
  * @max_msg_size: Maximum size of data per message that can be handled.
- * @rm_type_map: RM resource type mapping structure.
  */
 struct ti_sci_desc {
 	u8 default_host_id;
 	int max_rx_timeout_ms;
 	int max_msgs;
 	int max_msg_size;
-	struct ti_sci_rm_type_map *rm_type_map;
 };
 
 /**
@@ -1710,33 +1692,6 @@ static int ti_sci_cmd_core_reboot(const struct ti_sci_handle *handle)
 	return ret;
 }
 
-static int ti_sci_get_resource_type(struct ti_sci_info *info, u16 dev_id,
-				    u16 *type)
-{
-	struct ti_sci_rm_type_map *rm_type_map = info->desc->rm_type_map;
-	bool found = false;
-	int i;
-
-	/* If map is not provided then assume dev_id is used as type */
-	if (!rm_type_map) {
-		*type = dev_id;
-		return 0;
-	}
-
-	for (i = 0; rm_type_map[i].dev_id; i++) {
-		if (rm_type_map[i].dev_id == dev_id) {
-			*type = rm_type_map[i].type;
-			found = true;
-			break;
-		}
-	}
-
-	if (!found)
-		return -EINVAL;
-
-	return 0;
-}
-
 /**
  * ti_sci_get_resource_range - Helper to get a range of resources assigned
  *			       to a host. Resource is uniquely identified by
@@ -1760,7 +1715,6 @@ static int ti_sci_get_resource_range(const struct ti_sci_handle *handle,
 	struct ti_sci_xfer *xfer;
 	struct ti_sci_info *info;
 	struct device *dev;
-	u16 type;
 	int ret = 0;
 
 	if (IS_ERR(handle))
@@ -1780,15 +1734,9 @@ static int ti_sci_get_resource_range(const struct ti_sci_handle *handle,
 		return ret;
 	}
 
-	ret = ti_sci_get_resource_type(info, dev_id, &type);
-	if (ret) {
-		dev_err(dev, "rm type lookup failed for %u\n", dev_id);
-		goto fail;
-	}
-
 	req = (struct ti_sci_msg_req_get_resource_range *)xfer->xfer_buf;
 	req->secondary_host = s_host;
-	req->type = type & MSG_RM_RESOURCE_TYPE_MASK;
+	req->type = dev_id & MSG_RM_RESOURCE_TYPE_MASK;
 	req->subtype = subtype & MSG_RM_RESOURCE_SUBTYPE_MASK;
 
 	ret = ti_sci_do_xfer(info, xfer);
@@ -3352,7 +3300,6 @@ static const struct ti_sci_desc ti_sci_pmmc_k2g_desc = {
 	/* Limited by MBOX_TX_QUEUE_LEN. K2G can handle upto 128 messages! */
 	.max_msgs = 20,
 	.max_msg_size = 64,
-	.rm_type_map = NULL,
 };
 
 /* Description for AM654 */
@@ -3363,7 +3310,6 @@ static const struct ti_sci_desc ti_sci_pmmc_am654_desc = {
 	/* Limited by MBOX_TX_QUEUE_LEN. K2G can handle upto 128 messages! */
 	.max_msgs = 20,
 	.max_msg_size = 60,
-	.rm_type_map = NULL,
 };
 
 static const struct of_device_id ti_sci_of_match[] = {
-- 
2.17.1

[PATCH 03/12] firmware: ti_sci: Add support for getting resource with subtype

[Lokesh Vutla]

With SYSFW ABI 3.0 changes, interrupts coming out of an interrupt
controller is identified by a type and it is consistent across SoCs.
Similarly global events for Interrupt aggregator. So add an API to get
resource range using a resource type.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 drivers/firmware/ti_sci.c              | 89 +++++++++++++++++++-------
 include/linux/soc/ti/ti_sci_protocol.h | 13 ++++
 2 files changed, 80 insertions(+), 22 deletions(-)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index a81ddec9e669..918117be4a73 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -3208,61 +3208,50 @@ u32 ti_sci_get_num_resources(struct ti_sci_resource *res)
 EXPORT_SYMBOL_GPL(ti_sci_get_num_resources);
 
 /**
- * devm_ti_sci_get_of_resource() - Get a TISCI resource assigned to a device
+ * devm_ti_sci_get_resource_sets() - Get a TISCI resources assigned to a device
  * @handle:	TISCI handle
  * @dev:	Device pointer to which the resource is assigned
  * @dev_id:	TISCI device id to which the resource is assigned
- * @of_prop:	property name by which the resource are represented
+ * @sub_types:	Array of sub_types assigned corresponding to device
+ * @sets:	Number of sub_types
  *
  * Return: Pointer to ti_sci_resource if all went well else appropriate
  *	   error pointer.
  */
-struct ti_sci_resource *
-devm_ti_sci_get_of_resource(const struct ti_sci_handle *handle,
-			    struct device *dev, u32 dev_id, char *of_prop)
+static struct ti_sci_resource *
+devm_ti_sci_get_resource_sets(const struct ti_sci_handle *handle,
+			      struct device *dev, u32 dev_id, u32 *sub_types,
+			      u32 sets)
 {
 	struct ti_sci_resource *res;
 	bool valid_set = false;
-	u32 resource_subtype;
 	int i, ret;
 
 	res = devm_kzalloc(dev, sizeof(*res), GFP_KERNEL);
 	if (!res)
 		return ERR_PTR(-ENOMEM);
 
-	ret = of_property_count_elems_of_size(dev_of_node(dev), of_prop,
-					      sizeof(u32));
-	if (ret < 0) {
-		dev_err(dev, "%s resource type ids not available\n", of_prop);
-		return ERR_PTR(ret);
-	}
-	res->sets = ret;
-
+	res->sets = sets;
 	res->desc = devm_kcalloc(dev, res->sets, sizeof(*res->desc),
 				 GFP_KERNEL);
 	if (!res->desc)
 		return ERR_PTR(-ENOMEM);
 
 	for (i = 0; i < res->sets; i++) {
-		ret = of_property_read_u32_index(dev_of_node(dev), of_prop, i,
-						 &resource_subtype);
-		if (ret)
-			return ERR_PTR(-EINVAL);
-
 		ret = handle->ops.rm_core_ops.get_range(handle, dev_id,
-							resource_subtype,
+							sub_types[i],
 							&res->desc[i].start,
 							&res->desc[i].num);
 		if (ret) {
 			dev_dbg(dev, "dev = %d subtype %d not allocated for this host\n",
-				dev_id, resource_subtype);
+				dev_id, sub_types[i]);
 			res->desc[i].start = 0;
 			res->desc[i].num = 0;
 			continue;
 		}
 
 		dev_dbg(dev, "dev = %d, subtype = %d, start = %d, num = %d\n",
-			dev_id, resource_subtype, res->desc[i].start,
+			dev_id, sub_types[i], res->desc[i].start,
 			res->desc[i].num);
 
 		valid_set = true;
@@ -3280,6 +3269,62 @@ devm_ti_sci_get_of_resource(const struct ti_sci_handle *handle,
 	return ERR_PTR(-EINVAL);
 }
 
+/**
+ * devm_ti_sci_get_of_resource() - Get a TISCI resource assigned to a device
+ * @handle:	TISCI handle
+ * @dev:	Device pointer to which the resource is assigned
+ * @dev_id:	TISCI device id to which the resource is assigned
+ * @of_prop:	property name by which the resource are represented
+ *
+ * Return: Pointer to ti_sci_resource if all went well else appropriate
+ *	   error pointer.
+ */
+struct ti_sci_resource *
+devm_ti_sci_get_of_resource(const struct ti_sci_handle *handle,
+			    struct device *dev, u32 dev_id, char *of_prop)
+{
+	struct ti_sci_resource *res;
+	u32 *sub_types;
+	int sets;
+
+	sets = of_property_count_elems_of_size(dev_of_node(dev), of_prop,
+					       sizeof(u32));
+	if (sets < 0) {
+		dev_err(dev, "%s resource type ids not available\n", of_prop);
+		return ERR_PTR(sets);
+	}
+
+	sub_types = kcalloc(sets, sizeof(*sub_types), GFP_KERNEL);
+	if (!sub_types)
+		return ERR_PTR(-ENOMEM);
+
+	of_property_read_u32_array(dev_of_node(dev), of_prop, sub_types, sets);
+	res = devm_ti_sci_get_resource_sets(handle, dev, dev_id, sub_types,
+					    sets);
+
+	kfree(sub_types);
+	return res;
+}
+EXPORT_SYMBOL_GPL(devm_ti_sci_get_of_resource);
+
+/**
+ * devm_ti_sci_get_resource() - Get a resource range assigned to the device
+ * @handle:	TISCI handle
+ * @dev:	Device pointer to which the resource is assigned
+ * @dev_id:	TISCI device id to which the resource is assigned
+ * @suub_type:	TISCI resource subytpe representing the resource.
+ *
+ * Return: Pointer to ti_sci_resource if all went well else appropriate
+ *	   error pointer.
+ */
+struct ti_sci_resource *
+devm_ti_sci_get_resource(const struct ti_sci_handle *handle, struct device *dev,
+			 u32 dev_id, u32 sub_type)
+{
+	return devm_ti_sci_get_resource_sets(handle, dev, dev_id, &sub_type, 1);
+}
+EXPORT_SYMBOL_GPL(devm_ti_sci_get_resource);
+
 static int tisci_reboot_handler(struct notifier_block *nb, unsigned long mode,
 				void *cmd)
 {
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index 9531ec823298..68e47f6324be 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -220,6 +220,9 @@ struct ti_sci_rm_core_ops {
 				    u16 *range_start, u16 *range_num);
 };
 
+#define TI_SCI_RESASG_SUBTYPE_IR_OUTPUT		0
+#define TI_SCI_RESASG_SUBTYPE_IA_VINT		0xa
+#define TI_SCI_RESASG_SUBTYPE_GLOBAL_EVENT_SEVT	0xd
 /**
  * struct ti_sci_rm_irq_ops: IRQ management operations
  * @set_irq:		Set an IRQ route between the requested source
@@ -556,6 +559,9 @@ u32 ti_sci_get_num_resources(struct ti_sci_resource *res);
 struct ti_sci_resource *
 devm_ti_sci_get_of_resource(const struct ti_sci_handle *handle,
 			    struct device *dev, u32 dev_id, char *of_prop);
+struct ti_sci_resource *
+devm_ti_sci_get_resource(const struct ti_sci_handle *handle, struct device *dev,
+			 u32 dev_id, u32 sub_type);
 
 #else	/* CONFIG_TI_SCI_PROTOCOL */
 
@@ -609,6 +615,13 @@ devm_ti_sci_get_of_resource(const struct ti_sci_handle *handle,
 {
 	return ERR_PTR(-EINVAL);
 }
+
+static inline struct ti_sci_resource *
+devm_ti_sci_get_resource(const struct ti_sci_handle *handle, struct device *dev,
+			 u32 dev_id, u32 sub_type);
+{
+	return ERR_PTR(-EINVAL);
+}
 #endif	/* CONFIG_TI_SCI_PROTOCOL */
 
 #endif	/* __TISCI_PROTOCOL_H */
-- 
2.17.1

[PATCH 04/12] dt-bindings: irqchip: ti,sci-intr: Update bindings to drop the usage of gic as parent

[Lokesh Vutla]

Drop the firmware related dt-bindings and use the hardware specified
interrupt numbers within Interrupt Router. This ensures interrupt router
DT node need not assume any interrupt parent type.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 .../interrupt-controller/ti,sci-intr.txt      | 31 ++++++++++---------
 1 file changed, 16 insertions(+), 15 deletions(-)

diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
index 1a8718f8855d..8b56b2de1c73 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
@@ -44,15 +44,17 @@ Required Properties:
 			4: If intr supports level triggered interrupts.
 - interrupt-controller:	Identifies the node as an interrupt controller
 - #interrupt-cells:	Specifies the number of cells needed to encode an
-			interrupt source. The value should be 2.
-			First cell should contain the TISCI device ID of source
-			Second cell should contain the interrupt source offset
-			within the device.
+			interrupt source. The value should be 1.
+			First cell should contain interrupt router input number
+			as specified by hardware.
 - ti,sci:		Phandle to TI-SCI compatible System controller node.
-- ti,sci-dst-id:	TISCI device ID of the destination IRQ controller.
-- ti,sci-rm-range-girq:	Array of TISCI subtype ids representing the host irqs
-			assigned to this interrupt router. Each subtype id
-			corresponds to a range of host irqs.
+- ti,sci-dev-id:	TISCI device id of interrupt controller.
+- ti,interrupt-ranges:	Set of triplets containing ranges that convert
+			the INTR output interrupt numbers to parent's
+			interrupt number. Each triplet has following entries:
+			- First entry specifies the base for intr output irq
+			- Second entry specifies the base for parent irqs
+			- Third entry specifies the limit
 
 For more details on TISCI IRQ resource management refer:
 http://downloads.ti.com/tisci/esd/latest/2_tisci_msgs/rm/rm_irq.html
@@ -62,21 +64,20 @@ Example:
 The following example demonstrates both interrupt router node and the consumer
 node(main gpio) on the AM654 SoC:
 
-main_intr: interrupt-controller0 {
+main_gpio_intr: interrupt-controller0 {
 	compatible = "ti,sci-intr";
 	ti,intr-trigger-type = <1>;
 	interrupt-controller;
 	interrupt-parent = <&gic500>;
-	#interrupt-cells = <2>;
+	#interrupt-cells = <1>;
 	ti,sci = <&dmsc>;
-	ti,sci-dst-id = <56>;
-	ti,sci-rm-range-girq = <0x1>;
+	ti,sci-dev-id = <131>;
+	ti,interrupt-ranges = <0 360 32>;
 };
 
 main_gpio0: gpio@600000 {
 	...
-	interrupt-parent = <&main_intr>;
-	interrupts = <57 256>, <57 257>, <57 258>,
-		     <57 259>, <57 260>, <57 261>;
+	interrupt-parent = <&main_gpio_intr>;
+	interrupts = <192>, <193>, <194>, <195>, <196>, <197>;
 	...
 };
-- 
2.17.1

[PATCH 05/12] dt-bindings: irqchip: Convert ti,sci-intr bindings to yaml

[Lokesh Vutla]

In order to automate the verification of DT nodes convert
ti,sci-intr.txt ti,sci-intr.yaml.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 .../interrupt-controller/ti,sci-intr.txt      |  83 -------------
 .../interrupt-controller/ti,sci-intr.yaml     | 113 ++++++++++++++++++
 MAINTAINERS                                   |   2 +-
 3 files changed, 114 insertions(+), 84 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml

diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
deleted file mode 100644
index 8b56b2de1c73..000000000000
--- a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
+++ /dev/null
@@ -1,83 +0,0 @@
-Texas Instruments K3 Interrupt Router
-=====================================
-
-The Interrupt Router (INTR) module provides a mechanism to mux M
-interrupt inputs to N interrupt outputs, where all M inputs are selectable
-to be driven per N output. An Interrupt Router can either handle edge triggered
-or level triggered interrupts and that is fixed in hardware.
-
-                                 Interrupt Router
-                             +----------------------+
-                             |  Inputs     Outputs  |
-        +-------+            | +------+    +-----+  |
-        | GPIO  |----------->| | irq0 |    |  0  |  |       Host IRQ
-        +-------+            | +------+    +-----+  |      controller
-                             |    .           .     |      +-------+
-        +-------+            |    .           .     |----->|  IRQ  |
-        | INTA  |----------->|    .           .     |      +-------+
-        +-------+            |    .        +-----+  |
-                             | +------+    |  N  |  |
-                             | | irqM |    +-----+  |
-                             | +------+             |
-                             |                      |
-                             +----------------------+
-
-There is one register per output (MUXCNTL_N) that controls the selection.
-Configuration of these MUXCNTL_N registers is done by a system controller
-(like the Device Memory and Security Controller on K3 AM654 SoC). System
-controller will keep track of the used and unused registers within the Router.
-Driver should request the system controller to get the range of GIC IRQs
-assigned to the requesting hosts. It is the drivers responsibility to keep
-track of Host IRQs.
-
-Communication between the host processor running an OS and the system
-controller happens through a protocol called TI System Control Interface
-(TISCI protocol). For more details refer:
-Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
-
-TISCI Interrupt Router Node:
-----------------------------
-Required Properties:
-- compatible:		Must be "ti,sci-intr".
-- ti,intr-trigger-type:	Should be one of the following:
-			1: If intr supports edge triggered interrupts.
-			4: If intr supports level triggered interrupts.
-- interrupt-controller:	Identifies the node as an interrupt controller
-- #interrupt-cells:	Specifies the number of cells needed to encode an
-			interrupt source. The value should be 1.
-			First cell should contain interrupt router input number
-			as specified by hardware.
-- ti,sci:		Phandle to TI-SCI compatible System controller node.
-- ti,sci-dev-id:	TISCI device id of interrupt controller.
-- ti,interrupt-ranges:	Set of triplets containing ranges that convert
-			the INTR output interrupt numbers to parent's
-			interrupt number. Each triplet has following entries:
-			- First entry specifies the base for intr output irq
-			- Second entry specifies the base for parent irqs
-			- Third entry specifies the limit
-
-For more details on TISCI IRQ resource management refer:
-http://downloads.ti.com/tisci/esd/latest/2_tisci_msgs/rm/rm_irq.html
-
-Example:
---------
-The following example demonstrates both interrupt router node and the consumer
-node(main gpio) on the AM654 SoC:
-
-main_gpio_intr: interrupt-controller0 {
-	compatible = "ti,sci-intr";
-	ti,intr-trigger-type = <1>;
-	interrupt-controller;
-	interrupt-parent = <&gic500>;
-	#interrupt-cells = <1>;
-	ti,sci = <&dmsc>;
-	ti,sci-dev-id = <131>;
-	ti,interrupt-ranges = <0 360 32>;
-};
-
-main_gpio0: gpio@600000 {
-	...
-	interrupt-parent = <&main_gpio_intr>;
-	interrupts = <192>, <193>, <194>, <195>, <196>, <197>;
-	...
-};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml
new file mode 100644
index 000000000000..fbc1e8631d6f
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml
@@ -0,0 +1,113 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/ti,sci-intr.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments K3 Interrupt Router
+
+maintainers:
+  - Lokesh Vutla <lokeshvutla@ti.com>
+
+allOf:
+  - $ref: /schemas/interrupt-controller.yaml#
+
+description: |
+  The Interrupt Router (INTR) module provides a mechanism to mux M
+  interrupt inputs to N interrupt outputs, where all M inputs are selectable
+  to be driven per N output. An Interrupt Router can either handle edge
+  triggered or level triggered interrupts and that is fixed in hardware.
+
+                                   Interrupt Router
+                               +----------------------+
+                               |  Inputs     Outputs  |
+          +-------+            | +------+    +-----+  |
+          | GPIO  |----------->| | irq0 |    |  0  |  |       Host IRQ
+          +-------+            | +------+    +-----+  |      controller
+                               |    .           .     |      +-------+
+          +-------+            |    .           .     |----->|  IRQ  |
+          | INTA  |----------->|    .           .     |      +-------+
+          +-------+            |    .        +-----+  |
+                               | +------+    |  N  |  |
+                               | | irqM |    +-----+  |
+                               | +------+             |
+                               |                      |
+                               +----------------------+
+
+  There is one register per output (MUXCNTL_N) that controls the selection.
+  Configuration of these MUXCNTL_N registers is done by a system controller
+  (like the Device Memory and Security Controller on K3 AM654 SoC). System
+  controller will keep track of the used and unused registers within the Router.
+  Driver should request the system controller to get the range of GIC IRQs
+  assigned to the requesting hosts. It is the drivers responsibility to keep
+  track of Host IRQs.
+
+  Communication between the host processor running an OS and the system
+  controller happens through a protocol called TI System Control Interface
+  (TISCI protocol).
+
+properties:
+  compatible:
+    const: ti,sci-intr
+
+  ti,intr-trigger-type:
+    description: |
+      Should be one of the following.
+        1 = If intr supports edge triggered interrupts.
+        4 = If intr supports level triggered interrupts.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 1
+    description: |
+      The 1st cell should contain interrupt router input hw number.
+
+  ti,sci:
+    description: phandle to TI-SCI compatible System controller node
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/phandle
+
+  ti,sci-dev-id:
+    description: TI-SCI device id of Interrupt Controller
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+
+  ti,interrupt-ranges:
+    description: |
+      Interrupt ranges that converts the INTR output hw irq numbers
+      to parents's input interrupt numbers.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-matrix
+      - items:
+          items:
+            - description: |
+                "output_irq" specifies the base for intr output irq
+            - description: |
+                "parent's input irq" specifies the base for parent irq
+            - description: |
+                "limit" specifies the limit for translation
+
+required:
+  - compatible
+  - ti,intr-trigger-type
+  - interrupt-controller
+  - '#interrupt-cells'
+  - ti,sci
+  - ti,sci-dev-id
+  - ti,interrupt-ranges
+
+examples:
+  - |
+    main_gpio_intr: interrupt-controller0 {
+        compatible = "ti,sci-intr";
+        ti,intr-trigger-type = <1>;
+        interrupt-controller;
+        interrupt-parent = <&gic500>;
+        #interrupt-cells = <1>;
+        ti,sci = <&dmsc>;
+        ti,sci-dev-id = <131>;
+        ti,interrupt-ranges = <0 360 32>;
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 7b58ca29cc80..56f69be90346 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -16652,7 +16652,7 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
 F:	Documentation/devicetree/bindings/clock/ti,sci-clk.txt
 F:	Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
-F:	Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
+F:	Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml
 F:	Documentation/devicetree/bindings/reset/ti,sci-reset.txt
 F:	Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
 F:	drivers/clk/keystone/sci-clk.c
-- 
2.17.1

[PATCH 06/12] irqchip/ti-sci-intr: Add support for INTR being a parent to INTR

[Lokesh Vutla]

Driver assumes that Interrupt parent to Interrupt router is always GIC.
This is not true always and an Interrupt Router can be a parent to
Interrupt Router. Update the driver to detect the parent and request the
parent irqs accordingly.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 drivers/irqchip/irq-ti-sci-intr.c | 150 ++++++++++++++++++------------
 1 file changed, 91 insertions(+), 59 deletions(-)

diff --git a/drivers/irqchip/irq-ti-sci-intr.c b/drivers/irqchip/irq-ti-sci-intr.c
index 59d51a20bbd8..0b73816e77fc 100644
--- a/drivers/irqchip/irq-ti-sci-intr.c
+++ b/drivers/irqchip/irq-ti-sci-intr.c
@@ -17,29 +17,18 @@
 #include <linux/of_irq.h>
 #include <linux/soc/ti/ti_sci_protocol.h>
 
-#define TI_SCI_DEV_ID_MASK	0xffff
-#define TI_SCI_DEV_ID_SHIFT	16
-#define TI_SCI_IRQ_ID_MASK	0xffff
-#define TI_SCI_IRQ_ID_SHIFT	0
-#define HWIRQ_TO_DEVID(hwirq)	(((hwirq) >> (TI_SCI_DEV_ID_SHIFT)) & \
-				 (TI_SCI_DEV_ID_MASK))
-#define HWIRQ_TO_IRQID(hwirq)	((hwirq) & (TI_SCI_IRQ_ID_MASK))
-#define TO_HWIRQ(dev, index)	((((dev) & TI_SCI_DEV_ID_MASK) << \
-				 TI_SCI_DEV_ID_SHIFT) | \
-				((index) & TI_SCI_IRQ_ID_MASK))
-
 /**
  * struct ti_sci_intr_irq_domain - Structure representing a TISCI based
  *				   Interrupt Router IRQ domain.
  * @sci:	Pointer to TISCI handle
- * @dst_irq:	TISCI resource pointer representing GIC irq controller.
- * @dst_id:	TISCI device ID of the GIC irq controller.
+ * @out_irqs:	TISCI resource pointer representing INTR irqs.
+ * @pdev:	Pointer to platform device.
  * @type:	Specifies the trigger type supported by this Interrupt Router
  */
 struct ti_sci_intr_irq_domain {
 	const struct ti_sci_handle *sci;
-	struct ti_sci_resource *dst_irq;
-	u32 dst_id;
+	struct ti_sci_resource *out_irqs;
+	struct platform_device *pdev;
 	u32 type;
 };
 
@@ -70,15 +59,44 @@ static int ti_sci_intr_irq_domain_translate(struct irq_domain *domain,
 {
 	struct ti_sci_intr_irq_domain *intr = domain->host_data;
 
-	if (fwspec->param_count != 2)
+	if (fwspec->param_count != 1)
 		return -EINVAL;
 
-	*hwirq = TO_HWIRQ(fwspec->param[0], fwspec->param[1]);
+	*hwirq = fwspec->param[0];
 	*type = intr->type;
 
 	return 0;
 }
 
+/**
+ * ti_sci_intr_xlate_irq() - Translate hwirq to parent's hwirq.
+ * @intr:	IRQ domain corresponding to Interrupt Router
+ * @irq:	Hardware irq corresponding to the above irq domain
+ *
+ * Return parent irq number if translation is available else -ENOENT.
+ */
+static int ti_sci_intr_xlate_irq(struct ti_sci_intr_irq_domain *intr, u32 irq)
+{
+	struct device_node *np = dev_of_node(&intr->pdev->dev);
+	u32 base, pbase, size, len;
+	const __be32 *range;
+
+	range = of_get_property(np, "ti,interrupt-ranges", &len);
+	if (!range)
+		return irq;
+
+	for (len /= sizeof(*range); len >= 3; len -= 3) {
+		base = be32_to_cpu(*range++);
+		pbase = be32_to_cpu(*range++);
+		size = be32_to_cpu(*range++);
+
+		if (base <= irq && irq < base + size)
+			return irq - base + pbase;
+	}
+
+	return -ENOENT;
+}
+
 /**
  * ti_sci_intr_irq_domain_free() - Free the specified IRQs from the domain.
  * @domain:	Domain to which the irqs belong
@@ -89,66 +107,77 @@ static void ti_sci_intr_irq_domain_free(struct irq_domain *domain,
 					unsigned int virq, unsigned int nr_irqs)
 {
 	struct ti_sci_intr_irq_domain *intr = domain->host_data;
-	struct irq_data *data, *parent_data;
-	u16 dev_id, irq_index;
+	struct irq_data *data;
+	int out_irq;
 
-	parent_data = irq_domain_get_irq_data(domain->parent, virq);
 	data = irq_domain_get_irq_data(domain, virq);
-	irq_index = HWIRQ_TO_IRQID(data->hwirq);
-	dev_id = HWIRQ_TO_DEVID(data->hwirq);
+	out_irq = (uintptr_t)data->chip_data;
 
-	intr->sci->ops.rm_irq_ops.free_irq(intr->sci, dev_id, irq_index,
-					   intr->dst_id, parent_data->hwirq);
-	ti_sci_release_resource(intr->dst_irq, parent_data->hwirq);
+	intr->sci->ops.rm_irq_ops.free_irq(intr->sci,
+					   intr->pdev->id, data->hwirq,
+					   intr->pdev->id, out_irq);
+	ti_sci_release_resource(intr->out_irqs, out_irq);
 	irq_domain_free_irqs_parent(domain, virq, 1);
 	irq_domain_reset_irq_data(data);
 }
 
 /**
- * ti_sci_intr_alloc_gic_irq() - Allocate GIC specific IRQ
+ * ti_sci_intr_alloc_parent_irq() - Allocate parent IRQ
  * @domain:	Pointer to the interrupt router IRQ domain
  * @virq:	Corresponding Linux virtual IRQ number
  * @hwirq:	Corresponding hwirq for the IRQ within this IRQ domain
  *
- * Returns 0 if all went well else appropriate error pointer.
+ * Returns parent irq if all went well else appropriate error pointer.
  */
-static int ti_sci_intr_alloc_gic_irq(struct irq_domain *domain,
-				     unsigned int virq, u32 hwirq)
+static int ti_sci_intr_alloc_parent_irq(struct irq_domain *domain,
+					unsigned int virq, u32 hwirq)
 {
 	struct ti_sci_intr_irq_domain *intr = domain->host_data;
+	struct device_node *parent_node;
 	struct irq_fwspec fwspec;
-	u16 dev_id, irq_index;
-	u16 dst_irq;
-	int err;
-
-	dev_id = HWIRQ_TO_DEVID(hwirq);
-	irq_index = HWIRQ_TO_IRQID(hwirq);
+	u16 out_irq, p_hwirq;
+	int err = 0;
 
-	dst_irq = ti_sci_get_free_resource(intr->dst_irq);
-	if (dst_irq == TI_SCI_RESOURCE_NULL)
+	out_irq = ti_sci_get_free_resource(intr->out_irqs);
+	if (out_irq == TI_SCI_RESOURCE_NULL)
 		return -EINVAL;
 
-	fwspec.fwnode = domain->parent->fwnode;
-	fwspec.param_count = 3;
-	fwspec.param[0] = 0;	/* SPI */
-	fwspec.param[1] = dst_irq - 32; /* SPI offset */
-	fwspec.param[2] = intr->type;
+	p_hwirq = ti_sci_intr_xlate_irq(intr, out_irq);
+	if (p_hwirq < 0)
+		goto err_irqs;
+
+	parent_node = of_irq_find_parent(dev_of_node(&intr->pdev->dev));
+	fwspec.fwnode = of_node_to_fwnode(parent_node);
+	if (of_property_read_u32(parent_node, "#interrupt-cells",
+				 &fwspec.param_count))
+		goto err_irqs;
+
+	if (of_device_is_compatible(parent_node, "arm,gic-v3")) {
+		/* Parent is GIC */
+		fwspec.param[0] = 0;	/* SPI */
+		fwspec.param[1] = p_hwirq - 32; /* SPI offset */
+		fwspec.param[2] = intr->type;
+	} else {
+		/* Parent is Interrupt Router */
+		fwspec.param[0] = p_hwirq;
+	}
 
 	err = irq_domain_alloc_irqs_parent(domain, virq, 1, &fwspec);
 	if (err)
 		goto err_irqs;
 
-	err = intr->sci->ops.rm_irq_ops.set_irq(intr->sci, dev_id, irq_index,
-						intr->dst_id, dst_irq);
+	err = intr->sci->ops.rm_irq_ops.set_irq(intr->sci,
+						intr->pdev->id, hwirq,
+						intr->pdev->id, out_irq);
 	if (err)
 		goto err_msg;
 
-	return 0;
+	return p_hwirq;
 
 err_msg:
 	irq_domain_free_irqs_parent(domain, virq, 1);
 err_irqs:
-	ti_sci_release_resource(intr->dst_irq, dst_irq);
+	ti_sci_release_resource(intr->out_irqs, out_irq);
 	return err;
 }
 
@@ -168,18 +197,19 @@ static int ti_sci_intr_irq_domain_alloc(struct irq_domain *domain,
 	struct irq_fwspec *fwspec = data;
 	unsigned long hwirq;
 	unsigned int flags;
-	int err;
+	int err, p_hwirq;
 
 	err = ti_sci_intr_irq_domain_translate(domain, fwspec, &hwirq, &flags);
 	if (err)
 		return err;
 
-	err = ti_sci_intr_alloc_gic_irq(domain, virq, hwirq);
-	if (err)
-		return err;
+	p_hwirq = ti_sci_intr_alloc_parent_irq(domain, virq, hwirq);
+	if (p_hwirq < 0)
+		return p_hwirq;
 
 	irq_domain_set_hwirq_and_chip(domain, virq, hwirq,
-				      &ti_sci_intr_irq_chip, NULL);
+				      &ti_sci_intr_irq_chip,
+				      (void *)(uintptr_t)p_hwirq);
 
 	return 0;
 }
@@ -214,6 +244,7 @@ static int ti_sci_intr_irq_domain_probe(struct platform_device *pdev)
 	if (!intr)
 		return -ENOMEM;
 
+	intr->pdev = pdev;
 	ret = of_property_read_u32(dev_of_node(dev), "ti,intr-trigger-type",
 				   &intr->type);
 	if (ret) {
@@ -230,19 +261,18 @@ static int ti_sci_intr_irq_domain_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	ret = of_property_read_u32(dev_of_node(dev), "ti,sci-dst-id",
-				   &intr->dst_id);
+	ret = of_property_read_u32(dev_of_node(dev), "ti,sci-dev-id",
+				   &pdev->id);
 	if (ret) {
-		dev_err(dev, "missing 'ti,sci-dst-id' property\n");
+		dev_err(dev, "missing 'ti,sci-dev-id' property\n");
 		return -EINVAL;
 	}
 
-	intr->dst_irq = devm_ti_sci_get_of_resource(intr->sci, dev,
-						    intr->dst_id,
-						    "ti,sci-rm-range-girq");
-	if (IS_ERR(intr->dst_irq)) {
+	intr->out_irqs = devm_ti_sci_get_resource(intr->sci, dev, pdev->id,
+					TI_SCI_RESASG_SUBTYPE_IR_OUTPUT);
+	if (IS_ERR(intr->out_irqs)) {
 		dev_err(dev, "Destination irq resource allocation failed\n");
-		return PTR_ERR(intr->dst_irq);
+		return PTR_ERR(intr->out_irqs);
 	}
 
 	domain = irq_domain_add_hierarchy(parent_domain, 0, 0, dev_of_node(dev),
@@ -252,6 +282,8 @@ static int ti_sci_intr_irq_domain_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
+	dev_info(dev, "Interrupt Router %d domain created\n", pdev->id);
+
 	return 0;
 }
 
-- 
2.17.1

[PATCH 07/12] dt-bindings: irqchip: ti,sci-inta: Update docs to support different parent.

[Lokesh Vutla]

Drop the firmware related interrupt ranges and use the hardware specified
interrupt numbers within Interrupt Aggregator. This ensures interrupt
aggregator DT node need not assume any interrupt parent type.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 .../interrupt-controller/ti,sci-inta.txt       | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
index 7841cb099e13..b14abec580a2 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
@@ -43,13 +43,14 @@ TISCI Interrupt Aggregator Node:
 - msi-controller:	Identifies the node as an MSI controller.
 - interrupt-parent:	phandle of irq parent.
 - ti,sci:		Phandle to TI-SCI compatible System controller node.
-- ti,sci-dev-id:	TISCI device ID of the Interrupt Aggregator.
-- ti,sci-rm-range-vint:	Array of TISCI subtype ids representing vints(inta
-			outputs) range within this INTA, assigned to the
-			requesting host context.
-- ti,sci-rm-range-global-event:	Array of TISCI subtype ids representing the
-			global events range reaching this IA and are assigned
-			to the requesting host context.
+- ti,sci-dev-id:	TISCI device id of interrupt controller.
+- ti,interrupt-ranges:	Set of triplets containing ranges that convert
+			the INTA output interrupt numbers to parent's
+			interrupt number. Each triplet has following entries:
+			- First entry specifies the base for vint
+			- Second entry specifies the base for parent irqs
+			- Third entry specifies the limit
+
 
 Example:
 --------
@@ -61,6 +62,5 @@ main_udmass_inta: interrupt-controller@33d00000 {
 	interrupt-parent = <&main_navss_intr>;
 	ti,sci = <&dmsc>;
 	ti,sci-dev-id = <179>;
-	ti,sci-rm-range-vint = <0x0>;
-	ti,sci-rm-range-global-event = <0x1>;
+	interrupt-ranges = <0 0 256>;
 };
-- 
2.17.1

[PATCH 08/12] dt-bindings: irqchip: Convert ti,sci-inta bindings to yaml

[Lokesh Vutla]

In order to automate the verification of DT nodes convert
ti,sci-inta.txt ti,sci-inta.yaml.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 .../interrupt-controller/ti,sci-inta.txt      |  66 -----------
 .../interrupt-controller/ti,sci-inta.yaml     | 104 ++++++++++++++++++
 MAINTAINERS                                   |   2 +-
 3 files changed, 105 insertions(+), 67 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.yaml

diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
deleted file mode 100644
index b14abec580a2..000000000000
--- a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
+++ /dev/null
@@ -1,66 +0,0 @@
-Texas Instruments K3 Interrupt Aggregator
-=========================================
-
-The Interrupt Aggregator (INTA) provides a centralized machine
-which handles the termination of system events to that they can
-be coherently processed by the host(s) in the system. A maximum
-of 64 events can be mapped to a single interrupt.
-
-
-                              Interrupt Aggregator
-                     +-----------------------------------------+
-                     |      Intmap            VINT             |
-                     | +--------------+  +------------+        |
-            m ------>| | vint  | bit  |  | 0 |.....|63| vint0  |
-               .     | +--------------+  +------------+        |       +------+
-               .     |         .               .               |       | HOST |
-Globalevents  ------>|         .               .               |------>| IRQ  |
-               .     |         .               .               |       | CTRL |
-               .     |         .               .               |       +------+
-            n ------>| +--------------+  +------------+        |
-                     | | vint  | bit  |  | 0 |.....|63| vintx  |
-                     | +--------------+  +------------+        |
-                     |                                         |
-                     +-----------------------------------------+
-
-Configuration of these Intmap registers that maps global events to vint is done
-by a system controller (like the Device Memory and Security Controller on K3
-AM654 SoC). Driver should request the system controller to get the range
-of global events and vints assigned to the requesting host. Management
-of these requested resources should be handled by driver and requests
-system controller to map specific global event to vint, bit pair.
-
-Communication between the host processor running an OS and the system
-controller happens through a protocol called TI System Control Interface
-(TISCI protocol). For more details refer:
-Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
-
-TISCI Interrupt Aggregator Node:
--------------------------------
-- compatible:		Must be "ti,sci-inta".
-- reg:			Should contain registers location and length.
-- interrupt-controller:	Identifies the node as an interrupt controller
-- msi-controller:	Identifies the node as an MSI controller.
-- interrupt-parent:	phandle of irq parent.
-- ti,sci:		Phandle to TI-SCI compatible System controller node.
-- ti,sci-dev-id:	TISCI device id of interrupt controller.
-- ti,interrupt-ranges:	Set of triplets containing ranges that convert
-			the INTA output interrupt numbers to parent's
-			interrupt number. Each triplet has following entries:
-			- First entry specifies the base for vint
-			- Second entry specifies the base for parent irqs
-			- Third entry specifies the limit
-
-
-Example:
---------
-main_udmass_inta: interrupt-controller@33d00000 {
-	compatible = "ti,sci-inta";
-	reg = <0x0 0x33d00000 0x0 0x100000>;
-	interrupt-controller;
-	msi-controller;
-	interrupt-parent = <&main_navss_intr>;
-	ti,sci = <&dmsc>;
-	ti,sci-dev-id = <179>;
-	interrupt-ranges = <0 0 256>;
-};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.yaml b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.yaml
new file mode 100644
index 000000000000..5e6cb76da45b
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.yaml
@@ -0,0 +1,104 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/ti,sci-inta.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments K3 Interrupt Aggregator
+
+maintainers:
+  - Lokesh Vutla <lokeshvutla@ti.com>
+
+allOf:
+  - $ref: /schemas/interrupt-controller.yaml#
+
+description: |
+  The Interrupt Aggregator (INTA) provides a centralized machine
+  which handles the termination of system events to that they can
+  be coherently processed by the host(s) in the system. A maximum
+  of 64 events can be mapped to a single interrupt.
+
+                                Interrupt Aggregator
+                       +-----------------------------------------+
+                       |      Intmap            VINT             |
+                       | +--------------+  +------------+        |
+              m ------>| | vint  | bit  |  | 0 |.....|63| vint0  |
+                 .     | +--------------+  +------------+        |      +------+
+                 .     |         .               .               |      | HOST |
+  Globalevents  ------>|         .               .               |----->| IRQ  |
+                 .     |         .               .               |      | CTRL |
+                 .     |         .               .               |      +------+
+              n ------>| +--------------+  +------------+        |
+                       | | vint  | bit  |  | 0 |.....|63| vintx  |
+                       | +--------------+  +------------+        |
+                       |                                         |
+                       +-----------------------------------------+
+
+  Configuration of these Intmap registers that maps global events to vint is
+  done by a system controller (like the Device Memory and Security Controller
+  on AM654 SoC). Driver should request the system controller to get the range
+  of global events and vints assigned to the requesting host. Management
+  of these requested resources should be handled by driver and requests
+  system controller to map specific global event to vint, bit pair.
+
+  Communication between the host processor running an OS and the system
+  controller happens through a protocol called TI System Control Interface
+  (TISCI protocol).
+
+properties:
+  compatible:
+    const: ti,sci-inta
+
+  reg:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  msi-controller: true
+
+  ti,sci:
+    description: phandle to TI-SCI compatible System controller node
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/phandle
+
+  ti,sci-dev-id:
+    description: TI-SCI device id of Interrupt Controller
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+
+  ti,interrupt-ranges:
+    description: |
+      Interrupt ranges that converts the INTR output hw irq numbers
+      to parents's input interrupt numbers.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-matrix
+      - items:
+          items:
+            - description: |
+                "output_irq" specifies the base for inta output irq
+            - description: |
+                "parent's input irq" specifies the base for parent irq
+            - description: |
+                "limit" specifies the limit for translation
+
+required:
+  - compatible
+  - reg
+  - interrupt-controller
+  - msi-controller
+  - ti,sci
+  - ti,sci-dev-id
+  - ti,interrupt-ranges
+
+examples:
+  - |
+    main_udmass_inta: interrupt-controller@33d00000 {
+            compatible = "ti,sci-inta";
+            reg = <0x0 0x33d00000 0x0 0x100000>;
+            interrupt-controller;
+            msi-controller;
+            interrupt-parent = <&main_navss_intr>;
+            ti,sci = <&dmsc>;
+            ti,sci-dev-id = <179>;
+            ti,interrupt-ranges = <0 0 256>;
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 56f69be90346..c0d65d1bc31f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -16651,7 +16651,7 @@ L:	linux-arm-kernel@lists.infradead.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
 F:	Documentation/devicetree/bindings/clock/ti,sci-clk.txt
-F:	Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
+F:	Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.yaml
 F:	Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml
 F:	Documentation/devicetree/bindings/reset/ti,sci-reset.txt
 F:	Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
-- 
2.17.1

[PATCH 09/12] irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC

[Lokesh Vutla]

Driver assumes that Interrupt parent to Interrupt Aggregator is always
Interrupt router. This is not true always and GIC can be a parent to
Interrupt Aggregator. Update the driver to detect the parent and request
the parent irqs accordingly.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 drivers/irqchip/irq-ti-sci-inta.c | 90 ++++++++++++++++++++++++++-----
 1 file changed, 77 insertions(+), 13 deletions(-)

diff --git a/drivers/irqchip/irq-ti-sci-inta.c b/drivers/irqchip/irq-ti-sci-inta.c
index 7e3ebf6ed2cd..00c17ade118a 100644
--- a/drivers/irqchip/irq-ti-sci-inta.c
+++ b/drivers/irqchip/irq-ti-sci-inta.c
@@ -8,6 +8,7 @@
 
 #include <linux/err.h>
 #include <linux/io.h>
+#include <linux/irq.h>
 #include <linux/irqchip.h>
 #include <linux/irqdomain.h>
 #include <linux/interrupt.h>
@@ -128,6 +129,37 @@ static void ti_sci_inta_irq_handler(struct irq_desc *desc)
 	chained_irq_exit(irq_desc_get_chip(desc), desc);
 }
 
+/**
+ * ti_sci_inta_xlate_irq() - Translate hwirq to parent's hwirq.
+ * @inta:	IRQ domain corresponding to Interrupt Aggregator
+ * @irq:	Hardware irq corresponding to the above irq domain
+ *
+ * Return parent irq number if translation is available else -ENOENT.
+ */
+static int ti_sci_inta_xlate_irq(struct ti_sci_inta_irq_domain *inta,
+				 u16 vint_id)
+{
+	struct device_node *np = dev_of_node(&inta->pdev->dev);
+	u32 base, parent_base, size;
+	const __be32 *range;
+	int len;
+
+	range = of_get_property(np, "ti,interrupt-ranges", &len);
+	if (!range)
+		return vint_id;
+
+	for (len /= sizeof(*range); len >= 3; len -= 3) {
+		base = be32_to_cpu(*range++);
+		parent_base = be32_to_cpu(*range++);
+		size = be32_to_cpu(*range++);
+
+		if (base <= vint_id && vint_id < base + size)
+			return vint_id - base + parent_base;
+	}
+
+	return -ENOENT;
+}
+
 /**
  * ti_sci_inta_alloc_parent_irq() - Allocate parent irq to Interrupt aggregator
  * @domain:	IRQ domain corresponding to Interrupt Aggregator
@@ -139,30 +171,55 @@ static struct ti_sci_inta_vint_desc *ti_sci_inta_alloc_parent_irq(struct irq_dom
 	struct ti_sci_inta_irq_domain *inta = domain->host_data;
 	struct ti_sci_inta_vint_desc *vint_desc;
 	struct irq_fwspec parent_fwspec;
+	struct device_node *parent_node;
 	unsigned int parent_virq;
-	u16 vint_id;
+	u16 vint_id, p_hwirq;
+	int ret;
 
 	vint_id = ti_sci_get_free_resource(inta->vint);
 	if (vint_id == TI_SCI_RESOURCE_NULL)
 		return ERR_PTR(-EINVAL);
 
+	p_hwirq = ti_sci_inta_xlate_irq(inta, vint_id);
+	if (p_hwirq < 0) {
+		ret = p_hwirq;
+		goto free_vint;
+	}
+
 	vint_desc = kzalloc(sizeof(*vint_desc), GFP_KERNEL);
-	if (!vint_desc)
-		return ERR_PTR(-ENOMEM);
+	if (!vint_desc) {
+		ret = -ENOMEM;
+		goto free_vint;
+	}
 
 	vint_desc->domain = domain;
 	vint_desc->vint_id = vint_id;
 	INIT_LIST_HEAD(&vint_desc->list);
 
-	parent_fwspec.fwnode = of_node_to_fwnode(of_irq_find_parent(dev_of_node(&inta->pdev->dev)));
-	parent_fwspec.param_count = 2;
-	parent_fwspec.param[0] = inta->pdev->id;
-	parent_fwspec.param[1] = vint_desc->vint_id;
+	parent_node = of_irq_find_parent(dev_of_node(&inta->pdev->dev));
+	parent_fwspec.fwnode = of_node_to_fwnode(parent_node);
+	if (of_property_read_u32(parent_node, "#interrupt-cells",
+				 &parent_fwspec.param_count)) {
+		ret = -EINVAL;
+		goto free_vint_desc;
+	}
+
+	if (of_device_is_compatible(parent_node, "arm,gic-v3")) {
+		/* Parent is GIC */
+		parent_fwspec.param[0] = 0;
+		parent_fwspec.param[1] = p_hwirq - 32;
+		parent_fwspec.param[2] = IRQ_TYPE_LEVEL_HIGH;
+	} else {
+		/* Parent is Interrupt Router */
+		parent_fwspec.param[0] = p_hwirq;
+	}
 
 	parent_virq = irq_create_fwspec_mapping(&parent_fwspec);
 	if (parent_virq == 0) {
-		kfree(vint_desc);
-		return ERR_PTR(-EINVAL);
+		dev_err(&inta->pdev->dev, "Parent IRQ allocation failed\n");
+		ret = -EINVAL;
+		goto free_vint_desc;
+
 	}
 	vint_desc->parent_virq = parent_virq;
 
@@ -171,6 +228,11 @@ static struct ti_sci_inta_vint_desc *ti_sci_inta_alloc_parent_irq(struct irq_dom
 					 ti_sci_inta_irq_handler, vint_desc);
 
 	return vint_desc;
+free_vint_desc:
+	kfree(vint_desc);
+free_vint:
+	ti_sci_release_resource(inta->vint, vint_id);
+	return ERR_PTR(ret);
 }
 
 /**
@@ -555,15 +617,15 @@ static int ti_sci_inta_irq_domain_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	inta->vint = devm_ti_sci_get_of_resource(inta->sci, dev, pdev->id,
-						 "ti,sci-rm-range-vint");
+	inta->vint = devm_ti_sci_get_resource(inta->sci, dev, pdev->id,
+					      TI_SCI_RESASG_SUBTYPE_IA_VINT);
 	if (IS_ERR(inta->vint)) {
 		dev_err(dev, "VINT resource allocation failed\n");
 		return PTR_ERR(inta->vint);
 	}
 
-	inta->global_event = devm_ti_sci_get_of_resource(inta->sci, dev, pdev->id,
-						"ti,sci-rm-range-global-event");
+	inta->global_event = devm_ti_sci_get_resource(inta->sci, dev, pdev->id,
+					TI_SCI_RESASG_SUBTYPE_GLOBAL_EVENT_SEVT);
 	if (IS_ERR(inta->global_event)) {
 		dev_err(dev, "Global event resource allocation failed\n");
 		return PTR_ERR(inta->global_event);
@@ -594,6 +656,8 @@ static int ti_sci_inta_irq_domain_probe(struct platform_device *pdev)
 	INIT_LIST_HEAD(&inta->vint_list);
 	mutex_init(&inta->vint_mutex);
 
+	dev_info(dev, "Interrupt Aggregator domain %d created\n", pdev->id);
+
 	return 0;
 }
 
-- 
2.17.1

[PATCH 10/12] arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings

[Lokesh Vutla]

Update the INTA and INTR dt nodes to the latest DT bindings.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 .../dts/ti/k3-j721e-common-proc-board.dts     | 10 ++---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi     | 41 ++++++++++---------
 .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi      | 11 +++--
 3 files changed, 31 insertions(+), 31 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 98e5e17e3ff7..022aa64d2911 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -223,7 +223,7 @@
 };
 
 &mailbox0_cluster0 {
-	interrupts = <214 0>;
+	interrupts = <436>;
 
 	mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
 		ti,mbox-rx = <0 0 0>;
@@ -237,7 +237,7 @@
 };
 
 &mailbox0_cluster1 {
-	interrupts = <215 0>;
+	interrupts = <432>;
 
 	mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
 		ti,mbox-rx = <0 0 0>;
@@ -251,7 +251,7 @@
 };
 
 &mailbox0_cluster2 {
-	interrupts = <216 0>;
+	interrupts = <428>;
 
 	mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 {
 		ti,mbox-rx = <0 0 0>;
@@ -265,7 +265,7 @@
 };
 
 &mailbox0_cluster3 {
-	interrupts = <217 0>;
+	interrupts = <424>;
 
 	mbox_c66_0: mbox-c66-0 {
 		ti,mbox-rx = <0 0 0>;
@@ -279,7 +279,7 @@
 };
 
 &mailbox0_cluster4 {
-	interrupts = <218 0>;
+	interrupts = <420>;
 
 	mbox_c71_0: mbox-c71-0 {
 		ti,mbox-rx = <0 0 0>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 0b9d14b838a1..2c643190ce0b 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -45,10 +45,10 @@
 		ti,intr-trigger-type = <1>;
 		interrupt-controller;
 		interrupt-parent = <&gic500>;
-		#interrupt-cells = <2>;
+		#interrupt-cells = <1>;
 		ti,sci = <&dmsc>;
-		ti,sci-dst-id = <14>;
-		ti,sci-rm-range-girq = <0x1>;
+		ti,sci-dev-id = <131>;
+		ti,interrupt-ranges = <8 392 56>;
 	};
 
 	main_navss {
@@ -66,10 +66,12 @@
 			ti,intr-trigger-type = <4>;
 			interrupt-controller;
 			interrupt-parent = <&gic500>;
-			#interrupt-cells = <2>;
+			#interrupt-cells = <1>;
 			ti,sci = <&dmsc>;
-			ti,sci-dst-id = <14>;
-			ti,sci-rm-range-girq = <0>, <2>;
+			ti,sci-dev-id = <213>;
+			ti,interrupt-ranges = <0 64 64>,
+					      <64 448 64>,
+					      <128 672 64>;
 		};
 
 		main_udmass_inta: interrupt-controller@33d00000 {
@@ -80,8 +82,7 @@
 			msi-controller;
 			ti,sci = <&dmsc>;
 			ti,sci-dev-id = <209>;
-			ti,sci-rm-range-vint = <0xa>;
-			ti,sci-rm-range-global-event = <0xd>;
+			ti,interrupt-ranges = <0 0 256>;
 		};
 
 		secure_proxy_main: mailbox@32c00000 {
@@ -401,8 +402,8 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&main_gpio_intr>;
-		interrupts = <105 0>, <105 1>, <105 2>, <105 3>,
-			     <105 4>, <105 5>, <105 6>, <105 7>;
+		interrupts = <256>, <257>, <258>, <259>,
+			     <260>, <261>, <262>, <263>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <128>;
@@ -418,7 +419,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&main_gpio_intr>;
-		interrupts = <106 0>, <106 1>, <106 2>;
+		interrupts = <288>, <289>, <290>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <36>;
@@ -434,8 +435,8 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&main_gpio_intr>;
-		interrupts = <107 0>, <107 1>, <107 2>, <107 3>,
-			     <107 4>, <107 5>, <107 6>, <107 7>;
+		interrupts = <264>, <265>, <266>, <267>,
+			     <268>, <269>, <270>, <271>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <128>;
@@ -451,7 +452,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&main_gpio_intr>;
-		interrupts = <108 0>, <108 1>, <108 2>;
+		interrupts = <292>, <293>, <294>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <36>;
@@ -467,8 +468,8 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&main_gpio_intr>;
-		interrupts = <109 0>, <109 1>, <109 2>, <109 3>,
-			     <109 4>, <109 5>, <109 6>, <109 7>;
+		interrupts = <272>, <273>, <274>, <275>,
+			     <276>, <277>, <278>, <279>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <128>;
@@ -484,7 +485,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&main_gpio_intr>;
-		interrupts = <110 0>, <110 1>, <110 2>;
+		interrupts = <296>, <297>, <298>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <36>;
@@ -500,8 +501,8 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&main_gpio_intr>;
-		interrupts = <111 0>, <111 1>, <111 2>, <111 3>,
-			     <111 4>, <111 5>, <111 6>, <111 7>;
+		interrupts = <280>, <281>, <282>, <283>,
+			     <284>, <285>, <286>, <287>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <128>;
@@ -517,7 +518,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&main_gpio_intr>;
-		interrupts = <112 0>, <112 1>, <112 2>;
+		interrupts = <300>, <301>, <302>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <36>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 3d6064125b40..a17074c8a172 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -96,9 +96,10 @@
 		ti,intr-trigger-type = <1>;
 		interrupt-controller;
 		interrupt-parent = <&gic500>;
-		#interrupt-cells = <2>;
+		#interrupt-cells = <1>;
 		ti,sci = <&dmsc>;
-		ti,sci-dst-id = <14>;
+		ti,sci-dev-id = <137>;
+		ti,interrupt-ranges = <16 960 16>;
 		ti,sci-rm-range-girq = <0x5>;
 	};
 
@@ -108,8 +109,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&wkup_gpio_intr>;
-		interrupts = <113 0>, <113 1>, <113 2>,
-			     <113 3>, <113 4>, <113 5>;
+		interrupts = <103>, <104>, <105>, <106>, <107>, <108>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <84>;
@@ -125,8 +125,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&wkup_gpio_intr>;
-		interrupts = <114 0>, <114 1>, <114 2>,
-			     <114 3>, <114 4>, <114 5>;
+		interrupts = <112>, <113>, <114>, <115>, <116>, <117>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <84>;
-- 
2.17.1

[PATCH 11/12] arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings

[Lokesh Vutla]

Update the INTA and INTR dt nodes to the latest DT bindings.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi      | 22 +++++++++----------
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi    |  8 +++----
 .../arm64/boot/dts/ti/k3-am654-base-board.dts |  4 ++--
 .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi      |  1 -
 4 files changed, 16 insertions(+), 19 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 11887c72f23a..84fe71db7023 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -372,10 +372,10 @@
 		ti,intr-trigger-type = <1>;
 		interrupt-controller;
 		interrupt-parent = <&gic500>;
-		#interrupt-cells = <2>;
+		#interrupt-cells = <1>;
 		ti,sci = <&dmsc>;
-		ti,sci-dst-id = <56>;
-		ti,sci-rm-range-girq = <0x1>;
+		ti,sci-dev-id = <100>;
+		ti,interrupt-ranges = <0 392 32>;
 	};
 
 	main_navss {
@@ -393,10 +393,11 @@
 			ti,intr-trigger-type = <4>;
 			interrupt-controller;
 			interrupt-parent = <&gic500>;
-			#interrupt-cells = <2>;
+			#interrupt-cells = <1>;
 			ti,sci = <&dmsc>;
-			ti,sci-dst-id = <56>;
-			ti,sci-rm-range-girq = <0x0>, <0x2>;
+			ti,sci-dev-id = <182>;
+			ti,interrupt-ranges = <0 64 64>,
+					      <64 448 64>;
 		};
 
 		inta_main_udmass: interrupt-controller@33d00000 {
@@ -407,8 +408,7 @@
 			msi-controller;
 			ti,sci = <&dmsc>;
 			ti,sci-dev-id = <179>;
-			ti,sci-rm-range-vint = <0x0>;
-			ti,sci-rm-range-global-event = <0x1>;
+			ti,interrupt-ranges = <0 0 256>;
 		};
 
 		secure_proxy_main: mailbox@32c00000 {
@@ -578,8 +578,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&intr_main_gpio>;
-		interrupts = <57 256>, <57 257>, <57 258>, <57 259>, <57 260>,
-				<57 261>;
+		interrupts = <192>, <193>, <194>, <195>, <196>, <197>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <96>;
@@ -594,8 +593,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&intr_main_gpio>;
-		interrupts = <58 256>, <58 257>, <58 258>, <58 259>, <58 260>,
-				<58 261>;
+		interrupts = <200>, <201>, <202>, <203>, <204>, <205>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <90>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index f4227e2743f2..72295fa64f0e 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -69,10 +69,10 @@
 		ti,intr-trigger-type = <1>;
 		interrupt-controller;
 		interrupt-parent = <&gic500>;
-		#interrupt-cells = <2>;
+		#interrupt-cells = <1>;
 		ti,sci = <&dmsc>;
-		ti,sci-dst-id = <56>;
-		ti,sci-rm-range-girq = <0x4>;
+		ti,sci-dev-id = <156>;
+		ti,interrupt-ranges = <0 712 16>;
 	};
 
 	wkup_gpio0: wkup_gpio0@42110000 {
@@ -81,7 +81,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&intr_wkup_gpio>;
-		interrupts = <59 128>, <59 129>, <59 130>, <59 131>;
+		interrupts = <60>, <61>, <62>, <63>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,ngpio = <56>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 2f3d3316a1cf..e58668f9fb59 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -359,7 +359,7 @@
 };
 
 &mailbox0_cluster0 {
-	interrupts = <164 0>;
+	interrupts = <436>;
 
 	mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
 		ti,mbox-tx = <1 0 0>;
@@ -368,7 +368,7 @@
 };
 
 &mailbox0_cluster1 {
-	interrupts = <165 0>;
+	interrupts = <432>;
 
 	mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
 		ti,mbox-tx = <1 0 0>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index a17074c8a172..cd1e782d08bd 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -100,7 +100,6 @@
 		ti,sci = <&dmsc>;
 		ti,sci-dev-id = <137>;
 		ti,interrupt-ranges = <16 960 16>;
-		ti,sci-rm-range-girq = <0x5>;
 	};
 
 	wkup_gpio0: gpio@42110000 {
-- 
2.17.1

[PATCH 12/12] arm64: dts: k3-am65: Update the RM resource types

[Lokesh Vutla]

Update the ringacc and udma dt nodes to use the latest RM resource types
similar to the ones used in k3-j721e dt nodes.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 12 ++++++------
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi  | 12 ++++++------
 2 files changed, 12 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 84fe71db7023..a3fb5c62d3bc 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -544,7 +544,7 @@
 				<0x0 0x33000000 0x0 0x40000>;
 			reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
 			ti,num-rings = <818>;
-			ti,sci-rm-range-gp-rings = <0x2>; /* GP ring range */
+			ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */
 			ti,dma-ring-reset-quirk;
 			ti,sci = <&dmsc>;
 			ti,sci-dev-id = <187>;
@@ -564,11 +564,11 @@
 			ti,sci-dev-id = <188>;
 			ti,ringacc = <&ringacc>;
 
-			ti,sci-rm-range-tchan = <0x1>, /* TX_HCHAN */
-						<0x2>; /* TX_CHAN */
-			ti,sci-rm-range-rchan = <0x4>, /* RX_HCHAN */
-						<0x5>; /* RX_CHAN */
-			ti,sci-rm-range-rflow = <0x6>; /* GP RFLOW */
+			ti,sci-rm-range-tchan = <0xf>, /* TX_HCHAN */
+						<0xd>; /* TX_CHAN */
+			ti,sci-rm-range-rchan = <0xb>, /* RX_HCHAN */
+						<0xa>; /* RX_CHAN */
+			ti,sci-rm-range-rflow = <0x0>; /* GP RFLOW */
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
index 353d1e2532a7..adc7e19194fc 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -134,7 +134,7 @@
 				<0x0 0x2a500000 0x0 0x40000>;
 			reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
 			ti,num-rings = <286>;
-			ti,sci-rm-range-gp-rings = <0x2>; /* GP ring range */
+			ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */
 			ti,dma-ring-reset-quirk;
 			ti,sci = <&dmsc>;
 			ti,sci-dev-id = <195>;
@@ -154,11 +154,11 @@
 			ti,sci-dev-id = <194>;
 			ti,ringacc = <&mcu_ringacc>;
 
-			ti,sci-rm-range-tchan = <0x1>, /* TX_HCHAN */
-						<0x2>; /* TX_CHAN */
-			ti,sci-rm-range-rchan = <0x3>, /* RX_HCHAN */
-						<0x4>; /* RX_CHAN */
-			ti,sci-rm-range-rflow = <0x5>; /* GP RFLOW */
+			ti,sci-rm-range-tchan = <0xf>, /* TX_HCHAN */
+						<0xd>; /* TX_CHAN */
+			ti,sci-rm-range-rchan = <0xb>, /* RX_HCHAN */
+						<0xa>; /* RX_CHAN */
+			ti,sci-rm-range-rflow = <0x0>; /* GP RFLOW */
 		};
 	};
 
-- 
2.17.1

Re: [PATCH 04/12] dt-bindings: irqchip: ti,sci-intr: Update bindings to drop the usage of gic as parent

[Rob Herring]

On Wed, May 20, 2020 at 06:14:46PM +0530, Lokesh Vutla wrote:
> Drop the firmware related dt-bindings and use the hardware specified
> interrupt numbers within Interrupt Router. This ensures interrupt router
> DT node need not assume any interrupt parent type.

I didn't like this binding to begin with, but now you're breaking 
compatibility.

> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> ---
>  .../interrupt-controller/ti,sci-intr.txt      | 31 ++++++++++---------
>  1 file changed, 16 insertions(+), 15 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
> index 1a8718f8855d..8b56b2de1c73 100644
> --- a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
> +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
> @@ -44,15 +44,17 @@ Required Properties:
>  			4: If intr supports level triggered interrupts.
>  - interrupt-controller:	Identifies the node as an interrupt controller
>  - #interrupt-cells:	Specifies the number of cells needed to encode an
> -			interrupt source. The value should be 2.
> -			First cell should contain the TISCI device ID of source
> -			Second cell should contain the interrupt source offset
> -			within the device.
> +			interrupt source. The value should be 1.
> +			First cell should contain interrupt router input number
> +			as specified by hardware.
>  - ti,sci:		Phandle to TI-SCI compatible System controller node.
> -- ti,sci-dst-id:	TISCI device ID of the destination IRQ controller.
> -- ti,sci-rm-range-girq:	Array of TISCI subtype ids representing the host irqs
> -			assigned to this interrupt router. Each subtype id
> -			corresponds to a range of host irqs.
> +- ti,sci-dev-id:	TISCI device id of interrupt controller.
> +- ti,interrupt-ranges:	Set of triplets containing ranges that convert
> +			the INTR output interrupt numbers to parent's
> +			interrupt number. Each triplet has following entries:
> +			- First entry specifies the base for intr output irq
> +			- Second entry specifies the base for parent irqs
> +			- Third entry specifies the limit

Humm, sounds like what interrupt-map does.

>  
>  For more details on TISCI IRQ resource management refer:
>  http://downloads.ti.com/tisci/esd/latest/2_tisci_msgs/rm/rm_irq.html
> @@ -62,21 +64,20 @@ Example:
>  The following example demonstrates both interrupt router node and the consumer
>  node(main gpio) on the AM654 SoC:
>  
> -main_intr: interrupt-controller0 {
> +main_gpio_intr: interrupt-controller0 {
>  	compatible = "ti,sci-intr";
>  	ti,intr-trigger-type = <1>;
>  	interrupt-controller;
>  	interrupt-parent = <&gic500>;
> -	#interrupt-cells = <2>;
> +	#interrupt-cells = <1>;
>  	ti,sci = <&dmsc>;
> -	ti,sci-dst-id = <56>;
> -	ti,sci-rm-range-girq = <0x1>;
> +	ti,sci-dev-id = <131>;
> +	ti,interrupt-ranges = <0 360 32>;
>  };
>  
>  main_gpio0: gpio@600000 {
>  	...
> -	interrupt-parent = <&main_intr>;
> -	interrupts = <57 256>, <57 257>, <57 258>,
> -		     <57 259>, <57 260>, <57 261>;
> +	interrupt-parent = <&main_gpio_intr>;
> +	interrupts = <192>, <193>, <194>, <195>, <196>, <197>;
>  	...
>  };
> -- 
> 2.17.1
> 

Re: [PATCH 04/12] dt-bindings: irqchip: ti,sci-intr: Update bindings to drop the usage of gic as parent

[Lokesh Vutla]

Hi Rob,

On 29/05/20 3:44 am, Rob Herring wrote:
> On Wed, May 20, 2020 at 06:14:46PM +0530, Lokesh Vutla wrote:
>> Drop the firmware related dt-bindings and use the hardware specified
>> interrupt numbers within Interrupt Router. This ensures interrupt router
>> DT node need not assume any interrupt parent type.
> 
> I didn't like this binding to begin with, but now you're breaking 
> compatibility.

Yes, I do agree that this change is breaking backward compatibility. But IMHO,
this does cleanup of firmware specific properties from DT. Since this is not
deployed out yet in the wild market, I took the leverage of breaking backward
compatibility. Before accepting these changes from firmware team, I did
discuss[0] with Marc on this topic.

> 
>> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
>> ---
>>  .../interrupt-controller/ti,sci-intr.txt      | 31 ++++++++++---------
>>  1 file changed, 16 insertions(+), 15 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>> index 1a8718f8855d..8b56b2de1c73 100644
>> --- a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>> +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>> @@ -44,15 +44,17 @@ Required Properties:
>>  			4: If intr supports level triggered interrupts.
>>  - interrupt-controller:	Identifies the node as an interrupt controller
>>  - #interrupt-cells:	Specifies the number of cells needed to encode an
>> -			interrupt source. The value should be 2.
>> -			First cell should contain the TISCI device ID of source
>> -			Second cell should contain the interrupt source offset
>> -			within the device.
>> +			interrupt source. The value should be 1.
>> +			First cell should contain interrupt router input number
>> +			as specified by hardware.
>>  - ti,sci:		Phandle to TI-SCI compatible System controller node.
>> -- ti,sci-dst-id:	TISCI device ID of the destination IRQ controller.
>> -- ti,sci-rm-range-girq:	Array of TISCI subtype ids representing the host irqs
>> -			assigned to this interrupt router. Each subtype id
>> -			corresponds to a range of host irqs.
>> +- ti,sci-dev-id:	TISCI device id of interrupt controller.
>> +- ti,interrupt-ranges:	Set of triplets containing ranges that convert
>> +			the INTR output interrupt numbers to parent's
>> +			interrupt number. Each triplet has following entries:
>> +			- First entry specifies the base for intr output irq
>> +			- Second entry specifies the base for parent irqs
>> +			- Third entry specifies the limit
> 
> Humm, sounds like what interrupt-map does.

 Okay, Ill look at it.

[0]
https://lore.kernel.org/linux-arm-kernel/2331f04eacee3b06cc152fc609225233@www.loen.fr/

Thanks and regards,
Lokesh

Re: [PATCH 04/12] dt-bindings: irqchip: ti,sci-intr: Update bindings to drop the usage of gic as parent

[Marc Zyngier]

On 2020-05-29 11:14, Lokesh Vutla wrote:
> Hi Rob,
> 
> On 29/05/20 3:44 am, Rob Herring wrote:
>> On Wed, May 20, 2020 at 06:14:46PM +0530, Lokesh Vutla wrote:
>>> Drop the firmware related dt-bindings and use the hardware specified
>>> interrupt numbers within Interrupt Router. This ensures interrupt 
>>> router
>>> DT node need not assume any interrupt parent type.
>> 
>> I didn't like this binding to begin with, but now you're breaking
>> compatibility.
> 
> Yes, I do agree that this change is breaking backward compatibility. 
> But IMHO,
> this does cleanup of firmware specific properties from DT. Since this 
> is not
> deployed out yet in the wild market, I took the leverage of breaking 
> backward
> compatibility. Before accepting these changes from firmware team, I did
> discuss[0] with Marc on this topic.

And I assume that should anyone complain about the kernel being broken
because they have an old firmware, you'll be OK with the patches being
reverted, right?

Thanks,

         M.
-- 
Jazz is not dead. It just smells funny...

Re: [PATCH 04/12] dt-bindings: irqchip: ti,sci-intr: Update bindings to drop the usage of gic as parent

[Lokesh Vutla]

Hi Rob,

[..snip..]
>>
>> diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>> index 1a8718f8855d..8b56b2de1c73 100644
>> --- a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>> +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
>> @@ -44,15 +44,17 @@ Required Properties:
>>  			4: If intr supports level triggered interrupts.
>>  - interrupt-controller:	Identifies the node as an interrupt controller
>>  - #interrupt-cells:	Specifies the number of cells needed to encode an
>> -			interrupt source. The value should be 2.
>> -			First cell should contain the TISCI device ID of source
>> -			Second cell should contain the interrupt source offset
>> -			within the device.
>> +			interrupt source. The value should be 1.
>> +			First cell should contain interrupt router input number
>> +			as specified by hardware.
>>  - ti,sci:		Phandle to TI-SCI compatible System controller node.
>> -- ti,sci-dst-id:	TISCI device ID of the destination IRQ controller.
>> -- ti,sci-rm-range-girq:	Array of TISCI subtype ids representing the host irqs
>> -			assigned to this interrupt router. Each subtype id
>> -			corresponds to a range of host irqs.
>> +- ti,sci-dev-id:	TISCI device id of interrupt controller.
>> +- ti,interrupt-ranges:	Set of triplets containing ranges that convert
>> +			the INTR output interrupt numbers to parent's
>> +			interrupt number. Each triplet has following entries:
>> +			- First entry specifies the base for intr output irq
>> +			- Second entry specifies the base for parent irqs
>> +			- Third entry specifies the limit
> 
> Humm, sounds like what interrupt-map does.

IIUC, for every irq translation there should be an entry in interrupt-map
property. These Controllers has interrupts ranging from 32, 256 and more. It
might be odd to have 256  entries in the interrupt map no? Also there are
multiple interrupt controllers which need such translations.

Thanks and regards,
Lokesh

Re: [PATCH 04/12] dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent

[Lokesh Vutla]

Hi Marc,

On 29/05/20 3:48 pm, Marc Zyngier wrote:
> On 2020-05-29 11:14, Lokesh Vutla wrote:
>> Hi Rob,
>>
>> On 29/05/20 3:44 am, Rob Herring wrote:
>>> On Wed, May 20, 2020 at 06:14:46PM +0530, Lokesh Vutla wrote:
>>>> Drop the firmware related dt-bindings and use the hardware specified
>>>> interrupt numbers within Interrupt Router. This ensures interrupt router
>>>> DT node need not assume any interrupt parent type.
>>>
>>> I didn't like this binding to begin with, but now you're breaking
>>> compatibility.
>>
>> Yes, I do agree that this change is breaking backward compatibility. But IMHO,
>> this does cleanup of firmware specific properties from DT. Since this is not
>> deployed out yet in the wild market, I took the leverage of breaking backward
>> compatibility. Before accepting these changes from firmware team, I did
>> discuss[0] with Marc on this topic.
> 
> And I assume that should anyone complain about the kernel being broken
> because they have an old firmware, you'll be OK with the patches being
> reverted, right?

I am assuming there is no one to complain as there is no product available yet
with upstream kernel. Internally everyone is aware of the changes. So, yes I
would agree with you to revert the changes if someone really needs it. :)

Thanks and regards,
Lokesh

Re: [PATCH 04/12] dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent

[Lokesh Vutla]

Hi Marc,

On 01/06/20 5:06 pm, Lokesh Vutla wrote:
> Hi Marc,
> 
> On 29/05/20 3:48 pm, Marc Zyngier wrote:
>> On 2020-05-29 11:14, Lokesh Vutla wrote:
>>> Hi Rob,
>>>
>>> On 29/05/20 3:44 am, Rob Herring wrote:
>>>> On Wed, May 20, 2020 at 06:14:46PM +0530, Lokesh Vutla wrote:
>>>>> Drop the firmware related dt-bindings and use the hardware specified
>>>>> interrupt numbers within Interrupt Router. This ensures interrupt router
>>>>> DT node need not assume any interrupt parent type.
>>>>
>>>> I didn't like this binding to begin with, but now you're breaking
>>>> compatibility.
>>>
>>> Yes, I do agree that this change is breaking backward compatibility. But IMHO,
>>> this does cleanup of firmware specific properties from DT. Since this is not
>>> deployed out yet in the wild market, I took the leverage of breaking backward
>>> compatibility. Before accepting these changes from firmware team, I did
>>> discuss[0] with Marc on this topic.
>>
>> And I assume that should anyone complain about the kernel being broken
>> because they have an old firmware, you'll be OK with the patches being
>> reverted, right?
> 
> I am assuming there is no one to complain as there is no product available yet
> with upstream kernel. Internally everyone is aware of the changes. So, yes I
> would agree with you to revert the changes if someone really needs it. :)

Any chance you can shower your blessings on this series :)

Thanks and regards,
Lokesh

> 
> Thanks and regards,
> Lokesh
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 

Re: [PATCH 04/12] dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent

[Marc Zyngier]

On 2020-06-15 09:03, Lokesh Vutla wrote:
> Hi Marc,
> 
> On 01/06/20 5:06 pm, Lokesh Vutla wrote:
>> Hi Marc,
>> 
>> On 29/05/20 3:48 pm, Marc Zyngier wrote:
>>> On 2020-05-29 11:14, Lokesh Vutla wrote:
>>>> Hi Rob,
>>>> 
>>>> On 29/05/20 3:44 am, Rob Herring wrote:
>>>>> On Wed, May 20, 2020 at 06:14:46PM +0530, Lokesh Vutla wrote:
>>>>>> Drop the firmware related dt-bindings and use the hardware 
>>>>>> specified
>>>>>> interrupt numbers within Interrupt Router. This ensures interrupt 
>>>>>> router
>>>>>> DT node need not assume any interrupt parent type.
>>>>> 
>>>>> I didn't like this binding to begin with, but now you're breaking
>>>>> compatibility.
>>>> 
>>>> Yes, I do agree that this change is breaking backward compatibility. 
>>>> But IMHO,
>>>> this does cleanup of firmware specific properties from DT. Since 
>>>> this is not
>>>> deployed out yet in the wild market, I took the leverage of breaking 
>>>> backward
>>>> compatibility. Before accepting these changes from firmware team, I 
>>>> did
>>>> discuss[0] with Marc on this topic.
>>> 
>>> And I assume that should anyone complain about the kernel being 
>>> broken
>>> because they have an old firmware, you'll be OK with the patches 
>>> being
>>> reverted, right?
>> 
>> I am assuming there is no one to complain as there is no product 
>> available yet
>> with upstream kernel. Internally everyone is aware of the changes. So, 
>> yes I
>> would agree with you to revert the changes if someone really needs it. 
>> :)
> 
> Any chance you can shower your blessings on this series :)

I have purposely ignored it just before and during the merge window. It 
is now firmly in my review queue.

         M.
-- 
Jazz is not dead. It just smells funny...

Re: [PATCH 04/12] dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent

[Lokesh Vutla]

Hi Marc,

On 15/06/20 2:04 pm, Marc Zyngier wrote:
> On 2020-06-15 09:03, Lokesh Vutla wrote:
>> Hi Marc,
>>
>> On 01/06/20 5:06 pm, Lokesh Vutla wrote:
>>> Hi Marc,
>>>
>>> On 29/05/20 3:48 pm, Marc Zyngier wrote:
>>>> On 2020-05-29 11:14, Lokesh Vutla wrote:
>>>>> Hi Rob,
>>>>>
>>>>> On 29/05/20 3:44 am, Rob Herring wrote:
>>>>>> On Wed, May 20, 2020 at 06:14:46PM +0530, Lokesh Vutla wrote:
>>>>>>> Drop the firmware related dt-bindings and use the hardware specified
>>>>>>> interrupt numbers within Interrupt Router. This ensures interrupt router
>>>>>>> DT node need not assume any interrupt parent type.
>>>>>>
>>>>>> I didn't like this binding to begin with, but now you're breaking
>>>>>> compatibility.
>>>>>
>>>>> Yes, I do agree that this change is breaking backward compatibility. But IMHO,
>>>>> this does cleanup of firmware specific properties from DT. Since this is not
>>>>> deployed out yet in the wild market, I took the leverage of breaking backward
>>>>> compatibility. Before accepting these changes from firmware team, I did
>>>>> discuss[0] with Marc on this topic.
>>>>
>>>> And I assume that should anyone complain about the kernel being broken
>>>> because they have an old firmware, you'll be OK with the patches being
>>>> reverted, right?
>>>
>>> I am assuming there is no one to complain as there is no product available yet
>>> with upstream kernel. Internally everyone is aware of the changes. So, yes I
>>> would agree with you to revert the changes if someone really needs it. :)
>>
>> Any chance you can shower your blessings on this series :)
> 
> I have purposely ignored it just before and during the merge window. It is now
> firmly in my review queue.

rc4 is tagged now. Do you want me to rebase, split the series and repost it?

Thanks and reagrds,
Lokesh

> 
>         M.