devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Thierry Reding <thierry.reding@gmail.com>
To: JC Kuo <jckuo@nvidia.com>
Cc: gregkh@linuxfoundation.org, robh@kernel.org,
	jonathanh@nvidia.com, kishon@ti.com, linux-tegra@vger.kernel.org,
	linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, nkristam@nvidia.com
Subject: Re: [PATCH v2 12/12] xhci: tegra: enable ELPG for runtime/system PM
Date: Mon, 31 Aug 2020 14:50:35 +0200	[thread overview]
Message-ID: <20200831125035.GH1689119@ulmo> (raw)
In-Reply-To: <20200831044043.1561074-13-jckuo@nvidia.com>

[-- Attachment #1: Type: text/plain, Size: 18885 bytes --]

On Mon, Aug 31, 2020 at 12:40:43PM +0800, JC Kuo wrote:
> This commit implements the complete programming sequence for ELPG
> entry and exit.
> 
>  1. At ELPG entry, invokes tegra_xusb_padctl_enable_phy_sleepwalk()
>     and tegra_xusb_padctl_enable_phy_wake() to configure XUSB PADCTL
>     sleepwalk and wake detection circuits to maintain USB lines level
>     and respond to wake events (wake-on-connect, wake-on-disconnect,
>     device-initiated-wake).
> 
>  2. At ELPG exit, invokes tegra_xusb_padctl_disable_phy_sleepwalk()
>     and tegra_xusb_padctl_disable_phy_wake() to disarm sleepwalk and
>     wake detection circuits.
> 
> At runtime suspend, XUSB host controller can enter ELPG to reduce
> power consumption. When XUSB PADCTL wake detection circuit detects
> a wake event, an interrupt will be raised. xhci-tegra driver then
> will invoke pm_runtime_resume() for xhci-tegra.
> 
> Runtime resume could also be triggered by protocol drivers, this is
> the host-initiated-wake event. At runtime resume, xhci-tegra driver
> brings XUSB host controller out of ELPG to handle the wake events.
> 
> The same ELPG enter/exit procedure will be performed for system
> suspend/resume path so USB devices can remain connected across SC7.
> 
> Signed-off-by: JC Kuo <jckuo@nvidia.com>
> ---
>  drivers/usb/host/xhci-tegra.c | 391 +++++++++++++++++++++++++++++++---
>  1 file changed, 361 insertions(+), 30 deletions(-)
> 
> diff --git a/drivers/usb/host/xhci-tegra.c b/drivers/usb/host/xhci-tegra.c
> index ce6526c2caf6..9530cfc83f45 100644
> --- a/drivers/usb/host/xhci-tegra.c
> +++ b/drivers/usb/host/xhci-tegra.c
> @@ -15,9 +15,11 @@
>  #include <linux/kernel.h>
>  #include <linux/module.h>
>  #include <linux/of_device.h>
> +#include <linux/of_irq.h>
>  #include <linux/phy/phy.h>
>  #include <linux/phy/tegra/xusb.h>
>  #include <linux/platform_device.h>
> +#include <linux/usb/ch9.h>
>  #include <linux/pm.h>
>  #include <linux/pm_domain.h>
>  #include <linux/pm_runtime.h>
> @@ -224,6 +226,7 @@ struct tegra_xusb {
>  
>  	int xhci_irq;
>  	int mbox_irq;
> +	int padctl_irq;
>  
>  	void __iomem *ipfs_base;
>  	void __iomem *fpci_base;
> @@ -268,10 +271,13 @@ struct tegra_xusb {
>  		dma_addr_t phys;
>  	} fw;
>  
> +	bool suspended;
>  	struct tegra_xusb_context context;
>  };
>  
>  static struct hc_driver __read_mostly tegra_xhci_hc_driver;
> +static int tegra_xusb_exit_elpg(struct tegra_xusb *tegra, bool runtime);
> +static int tegra_xusb_enter_elpg(struct tegra_xusb *tegra, bool runtime);
>  
>  static inline u32 fpci_readl(struct tegra_xusb *tegra, unsigned int offset)
>  {
> @@ -657,6 +663,9 @@ static irqreturn_t tegra_xusb_mbox_thread(int irq, void *data)
>  
>  	mutex_lock(&tegra->lock);
>  
> +	if (pm_runtime_suspended(tegra->dev) || tegra->suspended)
> +		goto out;
> +
>  	value = fpci_readl(tegra, tegra->soc->mbox.data_out);
>  	tegra_xusb_mbox_unpack(&msg, value);
>  
> @@ -670,6 +679,7 @@ static irqreturn_t tegra_xusb_mbox_thread(int irq, void *data)
>  
>  	tegra_xusb_mbox_handle(tegra, &msg);
>  
> +out:
>  	mutex_unlock(&tegra->lock);
>  	return IRQ_HANDLED;
>  }
> @@ -812,12 +822,27 @@ static void tegra_xusb_phy_disable(struct tegra_xusb *tegra)
>  
>  static int tegra_xusb_runtime_suspend(struct device *dev)
>  {
> -	return 0;
> +	struct tegra_xusb *tegra = dev_get_drvdata(dev);
> +	int ret;
> +
> +	synchronize_irq(tegra->mbox_irq);
> +	mutex_lock(&tegra->lock);
> +	ret = tegra_xusb_enter_elpg(tegra, true);
> +	mutex_unlock(&tegra->lock);
> +
> +	return ret;
>  }
>  
>  static int tegra_xusb_runtime_resume(struct device *dev)
>  {
> -	return 0;
> +	struct tegra_xusb *tegra = dev_get_drvdata(dev);
> +	int err;
> +
> +	mutex_lock(&tegra->lock);
> +	err = tegra_xusb_exit_elpg(tegra, true);
> +	mutex_unlock(&tegra->lock);
> +
> +	return err;
>  }
>  
>  #ifdef CONFIG_PM_SLEEP
> @@ -1121,6 +1146,22 @@ static int __tegra_xusb_enable_firmware_messages(struct tegra_xusb *tegra)
>  	return err;
>  }
>  
> +static irqreturn_t tegra_xusb_padctl_irq(int irq, void *data)
> +{
> +	struct tegra_xusb *tegra = data;
> +
> +	mutex_lock(&tegra->lock);
> +	if (tegra->suspended) {
> +		mutex_unlock(&tegra->lock);
> +		return IRQ_HANDLED;
> +	}
> +	mutex_unlock(&tegra->lock);

Blank lines before and after a block can help make this less cluttered.

> +
> +	pm_runtime_resume(tegra->dev);
> +
> +	return IRQ_HANDLED;
> +}
> +
>  static int tegra_xusb_enable_firmware_messages(struct tegra_xusb *tegra)
>  {
>  	int err;
> @@ -1244,6 +1285,51 @@ static void tegra_xhci_id_work(struct work_struct *work)
>  	}
>  }
>  
> +static bool is_usb2_otg_phy(struct tegra_xusb *tegra, int index)

unsigned int index?

> +{
> +	return (tegra->usbphy[index] != NULL);
> +}
> +
> +static bool is_usb3_otg_phy(struct tegra_xusb *tegra, int index)

Here too.

> +{
> +	struct tegra_xusb_padctl *padctl = tegra->padctl;
> +	int i, port;

These can also be unsigned.

> +
> +	for (i = 0; i < tegra->num_usb_phys; i++) {
> +		if (is_usb2_otg_phy(tegra, i)) {
> +			port = tegra_xusb_padctl_get_usb3_companion(padctl,i);

Space after ",".

> +			if (index == port)
> +				return true;
> +		}
> +	}
> +
> +	return false;
> +}
> +
> +static bool is_host_mode_phy(struct tegra_xusb *tegra, int phy_type, int index)
> +{
> +	if (strcmp(tegra->soc->phy_types[phy_type].name, "hsic") == 0)
> +		return true;
> +
> +	if (strcmp(tegra->soc->phy_types[phy_type].name, "usb2") == 0) {
> +		if (is_usb2_otg_phy(tegra, index)) {
> +			return ((index == tegra->otg_usb2_port) &&
> +				 tegra->host_mode);
> +		} else
> +			return true;
> +	}
> +
> +	if (strcmp(tegra->soc->phy_types[phy_type].name, "usb3") == 0) {
> +		if (is_usb3_otg_phy(tegra, index)) {
> +			return ((index == tegra->otg_usb3_port) &&
> +				 tegra->host_mode);
> +		} else
> +			return true;
> +	}
> +
> +	return false;
> +}
> +
>  static int tegra_xusb_get_usb2_port(struct tegra_xusb *tegra,
>  					      struct usb_phy *usbphy)
>  {
> @@ -1336,6 +1422,7 @@ static void tegra_xusb_deinit_usb_phy(struct tegra_xusb *tegra)
>  static int tegra_xusb_probe(struct platform_device *pdev)
>  {
>  	struct tegra_xusb *tegra;
> +	struct device_node *np;
>  	struct resource *regs;
>  	struct xhci_hcd *xhci;
>  	unsigned int i, j, k;
> @@ -1383,6 +1470,14 @@ static int tegra_xusb_probe(struct platform_device *pdev)
>  	if (IS_ERR(tegra->padctl))
>  		return PTR_ERR(tegra->padctl);
>  
> +	np = of_parse_phandle(pdev->dev.of_node, "nvidia,xusb-padctl", 0);
> +	if (!np)
> +		return -ENODEV;
> +
> +	tegra->padctl_irq = of_irq_get(np, 0);
> +	if (tegra->padctl_irq < 0)
> +		return tegra->padctl_irq;
> +
>  	tegra->host_clk = devm_clk_get(&pdev->dev, "xusb_host");
>  	if (IS_ERR(tegra->host_clk)) {
>  		err = PTR_ERR(tegra->host_clk);
> @@ -1527,6 +1622,7 @@ static int tegra_xusb_probe(struct platform_device *pdev)
>  		goto put_powerdomains;
>  	}
>  
> +	tegra->hcd->skip_phy_initialization = 1;
>  	tegra->hcd->regs = tegra->regs;
>  	tegra->hcd->rsrc_start = regs->start;
>  	tegra->hcd->rsrc_len = resource_size(regs);
> @@ -1609,12 +1705,6 @@ static int tegra_xusb_probe(struct platform_device *pdev)
>  		goto put_usb3;
>  	}
>  
> -	err = tegra_xusb_enable_firmware_messages(tegra);
> -	if (err < 0) {
> -		dev_err(&pdev->dev, "failed to enable messages: %d\n", err);
> -		goto remove_usb3;
> -	}
> -
>  	err = devm_request_threaded_irq(&pdev->dev, tegra->mbox_irq,
>  					tegra_xusb_mbox_irq,
>  					tegra_xusb_mbox_thread, 0,
> @@ -1624,12 +1714,40 @@ static int tegra_xusb_probe(struct platform_device *pdev)
>  		goto remove_usb3;
>  	}
>  
> +	err = devm_request_threaded_irq(&pdev->dev, tegra->padctl_irq,
> +		NULL,
> +		tegra_xusb_padctl_irq,
> +		IRQF_ONESHOT |
> +		IRQF_TRIGGER_HIGH,
> +		dev_name(&pdev->dev), tegra);

The alignment here is off. Also, try to make good use of those 100
columns.

> +	if (err < 0) {
> +		dev_err(&pdev->dev, "failed to request padctl IRQ: %d\n", err);
> +		goto remove_usb3;
> +	}
> +
> +	err = tegra_xusb_enable_firmware_messages(tegra);
> +	if (err < 0) {
> +		dev_err(&pdev->dev, "failed to enable messages: %d\n", err);
> +		goto remove_usb3;
> +	}
> +
>  	err = tegra_xusb_init_usb_phy(tegra);
>  	if (err < 0) {
>  		dev_err(&pdev->dev, "failed to init USB PHY: %d\n", err);
>  		goto remove_usb3;
>  	}
>  
> +	/* Enable wake for both USB 2.0 and USB 3.0 roothubs */
> +	device_init_wakeup(&tegra->hcd->self.root_hub->dev, true);
> +	device_init_wakeup(&xhci->shared_hcd->self.root_hub->dev, true);
> +	device_init_wakeup(tegra->dev, true);
> +
> +	pm_runtime_use_autosuspend(tegra->dev);
> +	pm_runtime_set_autosuspend_delay(tegra->dev, 2000);
> +	pm_runtime_mark_last_busy(tegra->dev);
> +	pm_runtime_set_active(tegra->dev);
> +	pm_runtime_enable(tegra->dev);
> +
>  	return 0;
>  
>  remove_usb3:
> @@ -1665,6 +1783,7 @@ static int tegra_xusb_remove(struct platform_device *pdev)
>  
>  	tegra_xusb_deinit_usb_phy(tegra);
>  
> +	pm_runtime_get_sync(&pdev->dev);
>  	usb_remove_hcd(xhci->shared_hcd);
>  	usb_put_hcd(xhci->shared_hcd);
>  	xhci->shared_hcd = NULL;
> @@ -1674,8 +1793,8 @@ static int tegra_xusb_remove(struct platform_device *pdev)
>  	dma_free_coherent(&pdev->dev, tegra->fw.size, tegra->fw.virt,
>  			  tegra->fw.phys);
>  
> -	pm_runtime_put_sync(&pdev->dev);
>  	pm_runtime_disable(&pdev->dev);
> +	pm_runtime_put(&pdev->dev);
>  
>  	tegra_xusb_powergate_partitions(tegra);
>  
> @@ -1717,9 +1836,17 @@ static bool xhci_hub_ports_suspended(struct xhci_hub *hub)
>  static int tegra_xusb_check_ports(struct tegra_xusb *tegra)
>  {
>  	struct xhci_hcd *xhci = hcd_to_xhci(tegra->hcd);
> +	struct xhci_hub *rhub =  xhci_get_rhub(xhci->main_hcd);
> +	struct xhci_bus_state *bus_state = &rhub->bus_state;
>  	unsigned long flags;
>  	int err = 0;
>  
> +	if (bus_state->bus_suspended) {
> +		/* xusb_hub_suspend() has just directed one or more USB2 port(s)
> +		 * to U3 state, it takes 3ms to enter U3. */
> +		usleep_range(3000, 4000);
> +	}
> +
>  	spin_lock_irqsave(&xhci->lock, flags);
>  
>  	if (!xhci_hub_ports_suspended(&xhci->usb2_rhub) ||
> @@ -1765,45 +1892,184 @@ static void tegra_xusb_restore_context(struct tegra_xusb *tegra)
>  	}
>  }
>  
> -static int tegra_xusb_enter_elpg(struct tegra_xusb *tegra, bool wakeup)
> +static enum usb_device_speed
> +tegra_xhci_portsc_to_speed(struct tegra_xusb *tegra, u32 portsc)
> +{
> +	if (DEV_LOWSPEED(portsc))
> +		return USB_SPEED_LOW;
> +	else if (DEV_HIGHSPEED(portsc))
> +		return USB_SPEED_HIGH;
> +	else if (DEV_FULLSPEED(portsc))
> +		return USB_SPEED_FULL;
> +	else if (DEV_SUPERSPEED_ANY(portsc))
> +		return USB_SPEED_SUPER;
> +	else
> +		return USB_SPEED_UNKNOWN;
> +}

As in a prior patch you can make this simpler by dropping the elses.

> +
> +static void tegra_xhci_enable_phy_sleepwalk_wake(struct tegra_xusb *tegra)
> +{
> +	struct tegra_xusb_padctl *padctl = tegra->padctl;
> +	struct xhci_hcd *xhci = hcd_to_xhci(tegra->hcd);
> +	enum usb_device_speed speed;
> +	struct phy *phy;
> +	int index, offset;
> +	int i, j, k;

It looks like these can all be unsigned int.

> +	struct xhci_hub *rhub;
> +	u32 portsc;
> +
> +	for (i = 0, k = 0; i < tegra->soc->num_types; i++) {
> +		if (strcmp(tegra->soc->phy_types[i].name, "usb3") == 0)
> +			rhub = &xhci->usb3_rhub;
> +		else
> +			rhub = &xhci->usb2_rhub;
> +
> +		if (strcmp(tegra->soc->phy_types[i].name, "hsic") == 0)
> +			offset = tegra->soc->ports.usb2.count;
> +		else
> +			offset = 0;
> +
> +		for (j = 0; j < tegra->soc->phy_types[i].num; j++) {
> +			phy = tegra->phys[k++];
> +
> +			if (!phy)
> +				continue;
> +
> +			index = j + offset;
> +
> +			if (index >= rhub->num_ports)
> +				continue;
> +
> +			if (!is_host_mode_phy(tegra, i, j))
> +				continue;
> +
> +			portsc = readl(rhub->ports[index]->addr);
> +			speed = tegra_xhci_portsc_to_speed(tegra, portsc);
> +			tegra_xusb_padctl_enable_phy_sleepwalk(padctl, phy,
> +							       speed);
> +			tegra_xusb_padctl_enable_phy_wake(padctl, phy);
> +		}
> +	}
> +}
> +
> +static void tegra_xhci_disable_phy_wake(struct tegra_xusb *tegra)
> +{
> +	struct tegra_xusb_padctl *padctl = tegra->padctl;
> +	int i;

Same here.

> +
> +	for (i = 0; i < tegra->num_phys; i++) {
> +		if (!tegra->phys[i])
> +			continue;
> +
> +		tegra_xusb_padctl_disable_phy_wake(padctl, tegra->phys[i]);
> +	}
> +}
> +
> +static void tegra_xhci_disable_phy_sleepwalk(struct tegra_xusb *tegra)
> +{
> +	struct tegra_xusb_padctl *padctl = tegra->padctl;
> +	int i;

And here.

> +
> +	for (i = 0; i < tegra->num_phys; i++) {
> +		if (!tegra->phys[i])
> +			continue;
> +
> +		tegra_xusb_padctl_disable_phy_sleepwalk(padctl, tegra->phys[i]);
> +	}
> +}
> +
> +static int tegra_xusb_enter_elpg(struct tegra_xusb *tegra, bool runtime)
>  {
>  	struct xhci_hcd *xhci = hcd_to_xhci(tegra->hcd);
> +	struct device *dev = tegra->dev;
> +	bool wakeup = runtime ? true : device_may_wakeup(dev);
> +	unsigned int i;
>  	int err;
> +	u32 usbcmd;
> +
> +	dev_dbg(dev, "entering ELPG\n");
> +
> +	usbcmd = readl(&xhci->op_regs->command);
> +	usbcmd &= ~CMD_EIE;
> +	writel(usbcmd, &xhci->op_regs->command);
>  
>  	err = tegra_xusb_check_ports(tegra);
>  	if (err < 0) {
>  		dev_err(tegra->dev, "not all ports suspended: %d\n", err);
> -		return err;
> +		goto out;
>  	}
>  
>  	err = xhci_suspend(xhci, wakeup);
>  	if (err < 0) {
>  		dev_err(tegra->dev, "failed to suspend XHCI: %d\n", err);
> -		return err;
> +		goto out;
>  	}
>  
>  	tegra_xusb_save_context(tegra);
> -	tegra_xusb_phy_disable(tegra);
> +
> +	if (wakeup)
> +		tegra_xhci_enable_phy_sleepwalk_wake(tegra);
> +
> +	tegra_xusb_powergate_partitions(tegra);
> +
> +	for (i = 0; i < tegra->num_phys; i++) {
> +		if (!tegra->phys[i])
> +			continue;
> +
> +		phy_power_off(tegra->phys[i]);
> +		if (!wakeup)
> +			phy_exit(tegra->phys[i]);
> +	}
>  	tegra_xusb_clk_disable(tegra);

Use blank lines to separate blocks of code.

>  
> -	return 0;
> +out:
> +	if (!err)
> +		dev_dbg(tegra->dev, "entering ELPG done\n");
> +	else {
> +		usbcmd = readl(&xhci->op_regs->command);
> +		usbcmd |= CMD_EIE;
> +		writel(usbcmd, &xhci->op_regs->command);
> +
> +		dev_dbg(tegra->dev, "entering ELPG failed\n");
> +		pm_runtime_mark_last_busy(tegra->dev);
> +	}
> +
> +	return err;
>  }
>  
> -static int tegra_xusb_exit_elpg(struct tegra_xusb *tegra, bool wakeup)
> +static int tegra_xusb_exit_elpg(struct tegra_xusb *tegra, bool runtime)
>  {
>  	struct xhci_hcd *xhci = hcd_to_xhci(tegra->hcd);
> +	struct device *dev = tegra->dev;
> +	bool wakeup = runtime ? true : device_may_wakeup(dev);
> +	unsigned int i;
> +	u32 usbcmd;
>  	int err;
>  
> +	dev_dbg(dev, "exiting ELPG\n");
> +	pm_runtime_mark_last_busy(tegra->dev);
> +
>  	err = tegra_xusb_clk_enable(tegra);
>  	if (err < 0) {
>  		dev_err(tegra->dev, "failed to enable clocks: %d\n", err);
> -		return err;
> +		goto out;
>  	}
>  
> -	err = tegra_xusb_phy_enable(tegra);
> -	if (err < 0) {
> -		dev_err(tegra->dev, "failed to enable PHYs: %d\n", err);
> -		goto disable_clk;
> +	err = tegra_xusb_unpowergate_partitions(tegra);
> +	if (err)
> +		goto disable_clks;
> +
> +	if (wakeup)
> +		tegra_xhci_disable_phy_wake(tegra);
> +
> +	for (i = 0; i < tegra->num_phys; i++) {
> +		if (!tegra->phys[i])
> +			continue;
> +
> +		if (!wakeup)
> +			phy_init(tegra->phys[i]);
> +
> +		phy_power_on(tegra->phys[i]);
>  	}
>  
>  	tegra_xusb_config(tegra);
> @@ -1821,31 +2087,78 @@ static int tegra_xusb_exit_elpg(struct tegra_xusb *tegra, bool wakeup)
>  		goto disable_phy;
>  	}
>  
> -	err = xhci_resume(xhci, true);
> +	if (wakeup)
> +		tegra_xhci_disable_phy_sleepwalk(tegra);
> +
> +	err = xhci_resume(xhci, 0);
>  	if (err < 0) {
>  		dev_err(tegra->dev, "failed to resume XHCI: %d\n", err);
>  		goto disable_phy;
>  	}
>  
> -	return 0;
> +	usbcmd = readl(&xhci->op_regs->command);
> +	usbcmd |= CMD_EIE;
> +	writel(usbcmd, &xhci->op_regs->command);
> +
> +	goto out;
>  
>  disable_phy:
> -	tegra_xusb_phy_disable(tegra);
> -disable_clk:
> +	for (i = 0; i < tegra->num_phys; i++) {
> +		if (!tegra->phys[i])
> +			continue;
> +
> +		phy_power_off(tegra->phys[i]);
> +		if (!wakeup)
> +			phy_exit(tegra->phys[i]);
> +	}
> +	tegra_xusb_powergate_partitions(tegra);
> +disable_clks:
>  	tegra_xusb_clk_disable(tegra);
> +out:
> +	if (!err)
> +		dev_dbg(dev, "exiting ELPG done\n");
> +	else
> +		dev_dbg(dev, "exiting ELPG failed\n");
> +
>  	return err;
>  }
>  
>  static int tegra_xusb_suspend(struct device *dev)
>  {
>  	struct tegra_xusb *tegra = dev_get_drvdata(dev);
> -	bool wakeup = device_may_wakeup(dev);
>  	int err;
>  
>  	synchronize_irq(tegra->mbox_irq);
> -

I think that blank line actually helped with readability.

Thierry

>  	mutex_lock(&tegra->lock);
> -	err = tegra_xusb_enter_elpg(tegra, wakeup);
> +
> +	if (pm_runtime_suspended(dev)) {
> +		err = tegra_xusb_exit_elpg(tegra, true);
> +		if (err < 0)
> +			goto out;
> +	}
> +
> +	err = tegra_xusb_enter_elpg(tegra, false);
> +	if (err < 0) {
> +		if (pm_runtime_suspended(dev)) {
> +			pm_runtime_disable(dev);
> +			pm_runtime_set_active(dev);
> +			pm_runtime_enable(dev);
> +		}
> +
> +		goto out;
> +	}
> +
> +out:
> +	if (!err) {
> +		tegra->suspended = true;
> +		pm_runtime_disable(dev);
> +
> +		if (device_may_wakeup(dev)) {
> +			if (enable_irq_wake(tegra->padctl_irq))
> +				dev_err(dev, "failed to enable padctl wakes\n");
> +		}
> +	}
> +
>  	mutex_unlock(&tegra->lock);
>  
>  	return err;
> @@ -1854,14 +2167,32 @@ static int tegra_xusb_suspend(struct device *dev)
>  static int tegra_xusb_resume(struct device *dev)
>  {
>  	struct tegra_xusb *tegra = dev_get_drvdata(dev);
> -	bool wakeup = device_may_wakeup(dev);
>  	int err;
>  
>  	mutex_lock(&tegra->lock);
> -	err = tegra_xusb_exit_elpg(tegra, wakeup);
> +
> +	if (!tegra->suspended) {
> +		mutex_unlock(&tegra->lock);
> +		return 0;
> +	}
> +
> +	err = tegra_xusb_exit_elpg(tegra, false);
> +	if (err < 0) {
> +		mutex_unlock(&tegra->lock);
> +		return err;
> +	}
> +
> +	if (device_may_wakeup(dev)) {
> +		if (disable_irq_wake(tegra->padctl_irq))
> +			dev_err(dev, "failed to disable padctl wakes\n");
> +	}
> +	tegra->suspended = false;
>  	mutex_unlock(&tegra->lock);
>  
> -	return err;
> +	pm_runtime_set_active(dev);
> +	pm_runtime_enable(dev);
> +
> +	return 0;
>  }
>  #endif
>  
> -- 
> 2.25.1
> 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

  reply	other threads:[~2020-08-31 12:50 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-08-31  4:40 [PATCH v2 00/12] Tegra XHCI controller ELPG support JC Kuo
2020-08-31  4:40 ` [PATCH v2 01/12] clk: tegra: Add PLLE HW power sequencer control JC Kuo
2020-08-31  4:40 ` [PATCH v2 02/12] clk: tegra: don't enable PLLE HW sequencer at init JC Kuo
2020-08-31  4:40 ` [PATCH v2 03/12] phy: tegra: xusb: t210: rearrange UPHY init JC Kuo
2020-08-31 11:42   ` Thierry Reding
2020-09-04  9:10     ` JC Kuo
2020-08-31  4:40 ` [PATCH v2 04/12] phy: tegra: xusb: t210: add lane_iddq operations JC Kuo
2020-08-31 11:53   ` Thierry Reding
2020-09-07  2:26     ` JC Kuo
2020-08-31  4:40 ` [PATCH v2 05/12] phy: tegra: xusb: add sleepwalk and suspend/resume JC Kuo
2020-08-31 11:58   ` Thierry Reding
2020-09-07  2:34     ` JC Kuo
2020-08-31  4:40 ` [PATCH v2 06/12] soc/tegra: pmc: provide usb sleepwalk register map JC Kuo
2020-08-31 12:09   ` Thierry Reding
2020-09-07  3:07     ` JC Kuo
2020-08-31  4:40 ` [PATCH v2 07/12] arm64: tegra210: XUSB PADCTL add "nvidia,pmc" prop JC Kuo
2020-08-31  4:40 ` [PATCH v2 08/12] phy: tegra: xusb: t210: support wake and sleepwalk JC Kuo
2020-08-31 12:37   ` Thierry Reding
2020-09-08  1:14     ` JC Kuo
2020-09-01 15:14   ` kernel test robot
2020-08-31  4:40 ` [PATCH v2 09/12] phy: tegra: xusb: t186: " JC Kuo
2020-08-31 12:38   ` Thierry Reding
2020-09-01 16:51   ` kernel test robot
2020-08-31  4:40 ` [PATCH v2 10/12] arm64: tegra210/tegra186/tegra194: XUSB PADCTL irq JC Kuo
2020-08-31  4:40 ` [PATCH v2 11/12] usb: host: xhci-tegra: unlink power domain devices JC Kuo
2020-08-31 12:42   ` Thierry Reding
2020-09-08  2:19     ` JC Kuo
2020-08-31  4:40 ` [PATCH v2 12/12] xhci: tegra: enable ELPG for runtime/system PM JC Kuo
2020-08-31 12:50   ` Thierry Reding [this message]
2020-09-08  2:29     ` JC Kuo
2020-09-01 20:33   ` Dmitry Osipenko
2020-09-08  2:42     ` JC Kuo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200831125035.GH1689119@ulmo \
    --to=thierry.reding@gmail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=jckuo@nvidia.com \
    --cc=jonathanh@nvidia.com \
    --cc=kishon@ti.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-tegra@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=nkristam@nvidia.com \
    --cc=robh@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).