From: Robert Marko <robert.marko@sartura.hr>
To: agross@kernel.org, bjorn.andersson@linaro.org,
robh+dt@kernel.org, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Robert Marko <robert.marko@sartura.hr>,
Luka Perkov <luka.perkov@sartura.hr>
Subject: [PATCH v2 3/4] arm: dts: add Alfa Network AP120C-AC
Date: Wed, 9 Sep 2020 21:56:39 +0200 [thread overview]
Message-ID: <20200909195640.3127341-4-robert.marko@sartura.hr> (raw)
In-Reply-To: <20200909195640.3127341-1-robert.marko@sartura.hr>
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.
Specification:
- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 or 512 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 1x button (reset)
- 1x USB 2.0
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)
This adds DTS for both the generic and custom Bit edition for Sartura.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
Changes since v1:
* Drop include that does not exist
arch/arm/boot/dts/Makefile | 2 +
.../boot/dts/qcom-ipq4018-ap120c-ac-bit.dts | 28 ++
arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts | 27 ++
arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi | 254 ++++++++++++++++++
4 files changed, 311 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
create mode 100644 arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
create mode 100644 arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9b474208057d..246d82fc5fcd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -890,6 +890,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
+ qcom-ipq4018-ap120c-ac.dtb \
+ qcom-ipq4018-ap120c-ac-bit.dtb \
qcom-ipq4018-jalapeno.dtb \
qcom-ipq4019-ap.dk01.1-c1.dtb \
qcom-ipq4019-ap.dk04.1-c1.dtb \
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
new file mode 100644
index 000000000000..028ac8e24797
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4018-ap120c-ac.dtsi"
+
+/ {
+ model = "ALFA Network AP120C-AC Bit";
+
+ leds {
+ compatible = "gpio-leds";
+
+ power {
+ label = "ap120c-ac:green:power";
+ gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wlan {
+ label = "ap120c-ac:green:wlan";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ support {
+ label = "ap120c-ac:green:support";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ panic-indicator;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
new file mode 100644
index 000000000000..b7916fc26d68
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4018-ap120c-ac.dtsi"
+
+/ {
+ leds {
+ compatible = "gpio-leds";
+
+ status: status {
+ label = "ap120c-ac:blue:status";
+ gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+
+ wlan2g {
+ label = "ap120c-ac:green:wlan2g";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5g {
+ label = "ap120c-ac:red:wlan5g";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
new file mode 100644
index 000000000000..1f3b1ce82108
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
@@ -0,0 +1,254 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "ALFA Network AP120C-AC";
+ compatible = "alfa-network,ap120c-ac";
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&tlmm {
+ i2c0_pins: i2c0_pinmux {
+ mux_i2c {
+ function = "blsp_i2c0";
+ pins = "gpio58", "gpio59";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ mdio_pins: mdio_pinmux {
+ mux_mdio {
+ pins = "gpio53";
+ function = "mdio";
+ bias-pull-up;
+ };
+
+ mux_mdc {
+ pins = "gpio52";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial0_pins: serial0_pinmux {
+ mux_uart {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi0_pins: spi0_pinmux {
+ mux_spi {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio4";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ usb-power {
+ line-name = "USB-power";
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
+ output-high;
+ };
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&prng {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_i2c3 {
+ status = "okay";
+
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+
+ tpm@29 {
+ compatible = "atmel,at97sc3204t";
+ reg = <0x29>;
+ };
+};
+
+&blsp1_spi1 {
+ status = "okay";
+
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 4 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "u-boot-env";
+ reg = <0x000e0000 0x00010000>;
+ };
+
+ partition@f0000 {
+ label = "u-boot";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition@170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "priv_data1";
+ reg = <0x00180000 0x00010000>;
+ read-only;
+ };
+
+ partition@190000 {
+ label = "priv_data2";
+ reg = <0x00190000 0x00010000>;
+ read-only;
+ };
+ };
+ };
+
+ nand@1 {
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ubi1";
+ reg = <0x00000000 0x04000000>;
+ };
+
+ partition@4000000 {
+ label = "ubi2";
+ reg = <0x04000000 0x04000000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ status = "okay";
+
+ pinctrl-0 = <&serial0_pins>;
+ pinctrl-names = "default";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+};
+
+&wifi0 {
+ status = "okay";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ALFA-Network-AP120C-AC";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb3 {
+ status = "okay";
+
+ dwc3@8a00000 {
+ phys = <&usb3_hs_phy>;
+ phy-names = "usb2-phy";
+ };
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
--
2.26.2
next prev parent reply other threads:[~2020-09-09 19:57 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-09 19:56 [PATCH v2 0/4] arm: dts: qcom: ipq4019: add more boards Robert Marko
2020-09-09 19:56 ` [PATCH v2 1/4] arm: dts: qcom: ipq4019: add more labels Robert Marko
2020-10-02 17:39 ` Robert Marko
2020-09-09 19:56 ` [PATCH v2 2/4] arm: dts: add 8devices Jalapeno Robert Marko
2020-09-10 3:06 ` kernel test robot
2020-10-02 17:40 ` Robert Marko
2020-09-09 19:56 ` Robert Marko [this message]
2020-10-02 17:40 ` [PATCH v2 3/4] arm: dts: add Alfa Network AP120C-AC Robert Marko
2020-09-09 19:56 ` [PATCH v2 4/4] arm: dts: add 8devices Habanero DVK Robert Marko
2020-10-02 17:41 ` Robert Marko
2021-01-22 18:56 ` Bjorn Andersson
2021-01-25 11:02 ` Robert Marko
[not found] ` <CA+HBbNHtvP7_8RovLs1L=C+iSpGTRAov17TuC58DwNkkAeSjfQ@mail.gmail.com>
2021-01-25 16:52 ` Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200909195640.3127341-4-robert.marko@sartura.hr \
--to=robert.marko@sartura.hr \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=luka.perkov@sartura.hr \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).