From: Peter Ujfalusi <peter.ujfalusi@ti.com>
To: <vkoul@kernel.org>, <nm@ti.com>, <ssantosh@kernel.org>,
<robh+dt@kernel.org>, <vigneshr@ti.com>
Cc: <dan.j.williams@intel.com>, <t-kristo@ti.com>,
<lokeshvutla@ti.com>, <linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<dmaengine@vger.kernel.org>
Subject: [PATCH 05/18] dmaengine: ti: k3-udma: Wait for peer teardown completion if supported
Date: Wed, 30 Sep 2020 12:13:59 +0300 [thread overview]
Message-ID: <20200930091412.8020-6-peter.ujfalusi@ti.com> (raw)
In-Reply-To: <20200930091412.8020-1-peter.ujfalusi@ti.com>
Set the TDTYPE if it is supported on the platform (j721e) which will cause
UDMAP to wait for the remote peer to finish the teardown before returning
the teardown completed message.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
drivers/dma/ti/k3-udma.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/dma/ti/k3-udma.c b/drivers/dma/ti/k3-udma.c
index de7bfc02a2de..3f798993a8b1 100644
--- a/drivers/dma/ti/k3-udma.c
+++ b/drivers/dma/ti/k3-udma.c
@@ -86,6 +86,7 @@ struct udma_rchan {
#define UDMA_FLAG_PDMA_ACC32 BIT(0)
#define UDMA_FLAG_PDMA_BURST BIT(1)
+#define UDMA_FLAG_TDTYPE BIT(2)
struct udma_match_data {
u32 psil_base;
@@ -1591,6 +1592,13 @@ static int udma_tisci_tx_channel_config(struct udma_chan *uc)
req_tx.tx_fetch_size = fetch_size >> 2;
req_tx.txcq_qnum = tc_ring;
req_tx.tx_atype = uc->config.atype;
+ if (uc->config.ep_type == PSIL_EP_PDMA_XY &&
+ ud->match_data->flags & UDMA_FLAG_TDTYPE) {
+ /* wait for peer to complete the teardown for PDMAs */
+ req_tx.valid_params |=
+ TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_TDTYPE_VALID;
+ req_tx.tx_tdtype = 1;
+ }
ret = tisci_ops->tx_ch_cfg(tisci_rm->tisci, &req_tx);
if (ret)
@@ -3107,14 +3115,14 @@ static struct udma_match_data am654_mcu_data = {
static struct udma_match_data j721e_main_data = {
.psil_base = 0x1000,
.enable_memcpy_support = true,
- .flags = UDMA_FLAG_PDMA_ACC32 | UDMA_FLAG_PDMA_BURST,
+ .flags = UDMA_FLAG_PDMA_ACC32 | UDMA_FLAG_PDMA_BURST | UDMA_FLAG_TDTYPE,
.statictr_z_mask = GENMASK(23, 0),
};
static struct udma_match_data j721e_mcu_data = {
.psil_base = 0x6000,
.enable_memcpy_support = false, /* MEM_TO_MEM is slow via MCU UDMA */
- .flags = UDMA_FLAG_PDMA_ACC32 | UDMA_FLAG_PDMA_BURST,
+ .flags = UDMA_FLAG_PDMA_ACC32 | UDMA_FLAG_PDMA_BURST | UDMA_FLAG_TDTYPE,
.statictr_z_mask = GENMASK(23, 0),
};
--
Peter
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
next prev parent reply other threads:[~2020-09-30 9:14 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-30 9:13 [PATCH 00/18] dmaengine/soc: k3-udma: Add support for BCDMA and PKTDMA Peter Ujfalusi
2020-09-30 9:13 ` [PATCH 01/18] dmaengine: of-dma: Add support for optional router configuration callback Peter Ujfalusi
2020-10-07 5:44 ` Vinod Koul
2020-10-07 8:08 ` Peter Ujfalusi
2020-10-07 15:55 ` Vinod Koul
2020-10-08 6:41 ` Peter Ujfalusi
2020-10-28 5:55 ` Vinod Koul
2020-10-28 9:56 ` Peter Ujfalusi
2020-11-09 11:45 ` Vinod Koul
2020-11-09 12:09 ` Peter Ujfalusi
2020-11-09 12:23 ` Vinod Koul
2020-11-09 12:36 ` Peter Ujfalusi
2020-09-30 9:13 ` [PATCH 02/18] dmaengine: Add support for per channel coherency handling Peter Ujfalusi
2020-09-30 9:13 ` [PATCH 03/18] dmaengine: doc: client: Update for dmaengine_get_dma_device() usage Peter Ujfalusi
2020-09-30 9:13 ` [PATCH 04/18] dmaengine: dmatest: Use dmaengine_get_dma_device Peter Ujfalusi
2020-09-30 9:13 ` Peter Ujfalusi [this message]
2020-09-30 9:14 ` [PATCH 06/18] dmaengine: ti: k3-udma: Add support for second resource range from sysfw Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 07/18] dmaengine: ti: k3-udma-glue: Add function to get device pointer for DMA API Peter Ujfalusi
2020-10-07 6:53 ` Vinod Koul
2020-10-07 8:22 ` Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 08/18] dmaengine: ti: k3-udma-glue: Configure the dma_dev for rings Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 09/18] dt-bindings: dma: ti: Add document for K3 BCDMA Peter Ujfalusi
2020-10-01 6:49 ` Peter Ujfalusi
2020-10-06 19:23 ` Rob Herring
2020-10-06 19:29 ` Rob Herring
2020-10-07 9:09 ` Peter Ujfalusi
2020-10-07 15:46 ` Rob Herring
2020-10-08 8:40 ` Peter Ujfalusi
2020-10-08 19:15 ` Rob Herring
2020-10-09 8:06 ` Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 10/18] dt-bindings: dma: ti: Add document for K3 PKTDMA Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 11/18] dmaengine: ti: k3-psil: Extend psil_endpoint_config " Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 12/18] dmaengine: ti: k3-psil: Add initial map for AM64 Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 13/18] dmaengine: ti: Add support for k3 event routers Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 14/18] soc: ti: k3-ringacc: add AM64 DMA rings support Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 15/18] dmaengine: ti: k3-udma: Initial support for K3 BCDMA Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 16/18] dmaengine: ti: k3-udma: Add support for BCDMA channel TPL handling Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 17/18] dmaengine: ti: k3-udma: Initial support for K3 PKTDMA Peter Ujfalusi
2020-09-30 9:14 ` [PATCH 18/18] dmaengine: ti: k3-udma-glue: Add " Peter Ujfalusi
2020-09-30 10:17 ` [PATCH 00/18] dmaengine/soc: k3-udma: Add support for BCDMA and PKTDMA Peter Ujfalusi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200930091412.8020-6-peter.ujfalusi@ti.com \
--to=peter.ujfalusi@ti.com \
--cc=dan.j.williams@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lokeshvutla@ti.com \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=ssantosh@kernel.org \
--cc=t-kristo@ti.com \
--cc=vigneshr@ti.com \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).