devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Alan Stern <stern@rowland.harvard.edu>
To: Doug Anderson <dianders@chromium.org>
Cc: Rob Herring <robh@kernel.org>,
	Matthias Kaehlcke <mka@chromium.org>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Frank Rowand <frowand.list@gmail.com>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	Linux USB List <linux-usb@vger.kernel.org>,
	Bastien Nocera <hadess@hadess.net>,
	Stephen Boyd <swboyd@chromium.org>,
	Ravi Chandra Sadineni <ravisadineni@chromium.org>,
	Krzysztof Kozlowski <krzk@kernel.org>,
	"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" 
	<devicetree@vger.kernel.org>, Peter Chen <peter.chen@nxp.com>
Subject: Re: [PATCH v4 1/2] dt-bindings: usb: Add binding for discrete onboard USB hubs
Date: Fri, 2 Oct 2020 14:36:33 -0400	[thread overview]
Message-ID: <20201002183633.GA296334@rowland.harvard.edu> (raw)
In-Reply-To: <CAD=FV=WJrvWBLk3oLpv6Q3uY4w7YeQBXVdkpn+SAS5dnxp9-=Q@mail.gmail.com>

On Fri, Oct 02, 2020 at 10:08:17AM -0700, Doug Anderson wrote:
> As a more similar example of single device that is listed in more than
> one location in the device tree, we can also look at embedded SDIO
> BT/WiFi combo cards.  This single device often provides WiFi under an
> SDIO bus and BT under a serial / USB bus.  I'm not 100% sure there are
> actually cases were the same board provides device tree data to both
> at the same time, but "brcm,bcm43540-bt" is an example of providing
> data to the Bluetooth (connected over serial port) and
> "brcm,bcm4329-fmac" to the WiFi (connected over the SDIO bus).  Of
> course WiFi/BT cheat in that the control logic is represented by the
> SDIO power sequencing stuff...
> 
> 
> Back to our case, though.  I guess the issue here is that we're the
> child of more than one bus.  Let's first pretend that the i2c lines of
> this hub are actually hooked up and establish how that would look
> first.  Then we can think about how it looks if this same device isn't
> hooked up via i2c.  In this case, it sounds as if you still don't want
> the device split among two nodes.  So I guess you'd prefer something
> like:
> 
> i2c {
>   usb-hub@xx {
>     reg = <xx>;
>     compatible = "realtek,rts5411", "onboard-usb-hub";
>     vdd-supply = <&pp3300_hub>;
>     usb-devices = <&usb_controller 1>;
>   };
> };
> 
> ...and then you wouldn't have anything under the USB controller
> itself.  Is that correct?  So even though there are existing bindings
> saying that a USB device should be listed via VID/PID, the desire to
> represent this as a single node overrides that, right?  (NOTE: this is
> similar to what Matthias proposed in his response except that I've
> added an index so that we don't need _anything_ under the controller).
> 
> Having this primarily listed under the i2c bus makes sense because the
> control logic for the hub is hooked up via i2c.  Having the power
> supply associated with it also makes some amount of sense since it's a
> control signal.  It's also convenient that i2c devices have their
> probe called _before_ we try to detect if they're there because it's
> common that i2c devices need power applied first.
> 
> Now, just because we don't have the i2c bus hooked up doesn't change
> the fact that there is control logic.  We also certainly wouldn't want
> two ways of describing this same hub: one way if the i2c is hooked up
> and one way if it's not hooked up.  To me this means that the we
> should be describing this hub as a top-level node if i2c isn't hooked
> up, just like we do with "smsc,usb3503a"
> 
> Said another way, we have these points:
> 
> a) The control logic for this bus could be hooked up to an i2c bus.
> 
> b) If the control logic is hooked up to an i2c bus it feels like
> that's where the device's primary node should be placed, not under the
> USB controller.
> 
> c) To keep the i2c and non-i2c case as similar as possible, if the i2c
> bus isn't hooked up the hub's primary node should be a top-level node,
> not under the USB controller.
> 
> 
> NOTE ALSO: the fact that we might want to list this hub under an i2c
> controller also seems like it's a good argument against putting this
> logic in the xhci-platform driver?

More and more we are going to see devices that are attached to multiple 
buses.  In this case, one for power control and another for 
commands/data.  If DT doesn't already have a canonical way of handling 
such situations, it needs to develop one soon.

One can make a case that there should be multiple device nodes in this 
situation, somehow referring to each other so that the system knows they 
all describe the same device.  Maybe one "primary" node for the device 
and the others acting kind of like symbolic links.

Regardless of how the situation is represented in DT, there remains the 
issue of where (i.e., in which driver module) the appropriate code 
belongs.  This goes far beyond USB.  In general, what happens when one 
sort of device normally isn't hooked up through a power regulator, so 
its driver doesn't have any code to enable a regulator, but then some 
system does exactly that?

Even worse, what if the device is on a discoverable bus, so the driver 
doesn't get invoked at all until the device is discovered, but on the 
new system it can't be discovered until the regulator is enabled?

Alan Stern

  reply	other threads:[~2020-10-02 18:36 UTC|newest]

Thread overview: 55+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-09-28 17:13 [PATCH v4 1/2] dt-bindings: usb: Add binding for discrete onboard USB hubs Matthias Kaehlcke
2020-09-28 17:13 ` [PATCH v4 2/2] USB: misc: Add onboard_usb_hub driver Matthias Kaehlcke
2020-09-28 18:47   ` Alan Stern
2020-09-29  1:43     ` Matthias Kaehlcke
2020-09-29 16:00       ` Alan Stern
2020-09-29 16:50         ` Matthias Kaehlcke
2020-09-28 22:03   ` Doug Anderson
2020-09-29  1:59     ` Matthias Kaehlcke
2020-09-28 22:13 ` [PATCH v4 1/2] dt-bindings: usb: Add binding for discrete onboard USB hubs Doug Anderson
2020-09-29  2:14   ` Matthias Kaehlcke
2020-09-29 20:17 ` Rob Herring
2020-09-29 22:09   ` Matthias Kaehlcke
2020-09-30  1:32     ` Alan Stern
2020-09-30 12:49       ` Matthias Kaehlcke
2020-09-30 14:44         ` Rob Herring
2020-09-30 15:28           ` Doug Anderson
2020-09-30 18:00             ` Doug Anderson
2020-09-30 19:19               ` Rob Herring
2020-10-01 21:39                 ` Matthias Kaehlcke
2020-09-30 19:19             ` Alan Stern
2020-09-30 20:20             ` Rob Herring
2020-10-01  1:24               ` Alan Stern
2020-10-01 21:54                 ` Matthias Kaehlcke
2020-10-02  1:21                   ` Alan Stern
2020-10-02 16:08                     ` Matthias Kaehlcke
2020-10-02 18:48                       ` Alan Stern
2020-10-02 17:08               ` Doug Anderson
2020-10-02 18:36                 ` Alan Stern [this message]
2020-10-02 22:58                   ` Rob Herring
2020-10-03 12:41                     ` Alan Stern
2020-10-05 16:06                       ` Matthias Kaehlcke
2020-10-05 16:15                         ` Alan Stern
2020-10-05 19:18                           ` Matthias Kaehlcke
2020-10-05 19:36                             ` Alan Stern
2020-10-05 19:59                               ` Rob Herring
2020-10-05 23:29                                 ` Matthias Kaehlcke
2020-10-05 19:36                             ` Rob Herring
2020-10-05 19:20                         ` Rob Herring
2020-10-02 22:28                 ` Rob Herring
2020-10-02 23:09                   ` Doug Anderson
2020-10-06  0:45                     ` Matthias Kaehlcke
2020-10-06 14:18                       ` Alan Stern
2020-10-06 16:59                         ` Matthias Kaehlcke
2020-10-06 17:15                           ` Alan Stern
2020-10-06 19:25                             ` Matthias Kaehlcke
2020-10-07  1:00                               ` Alan Stern
2020-10-07 16:03                                 ` Matthias Kaehlcke
2020-10-07 16:38                                   ` Alan Stern
2020-10-07 17:28                                     ` Matthias Kaehlcke
2020-10-07 19:25                                       ` Alan Stern
2020-10-07 19:42                                         ` Matthias Kaehlcke
2020-10-07 20:17                                           ` Alan Stern
2020-10-07 21:42                                             ` Matthias Kaehlcke
2020-10-08 14:09                                               ` Alan Stern
2020-10-09 23:13                                                 ` Matthias Kaehlcke

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201002183633.GA296334@rowland.harvard.edu \
    --to=stern@rowland.harvard.edu \
    --cc=devicetree@vger.kernel.org \
    --cc=dianders@chromium.org \
    --cc=frowand.list@gmail.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=hadess@hadess.net \
    --cc=krzk@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=mka@chromium.org \
    --cc=peter.chen@nxp.com \
    --cc=ravisadineni@chromium.org \
    --cc=robh@kernel.org \
    --cc=swboyd@chromium.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).