devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Vladimir Lypak <junak.pub@gmail.com>
To: Andy Gross <agross@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	Linus Walleij <linus.walleij@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	linux-arm-msm@vger.kernel.org, linux-gpio@vger.kernel.org,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Vladimir Lypak <junak.pub@gmail.com>
Subject: [PATCH 2/2] dt-bindings: pinctrl: qcom: add msm8953 pinctrl bindings
Date: Sun,  4 Oct 2020 11:16:44 +0300	[thread overview]
Message-ID: <20201004081644.323858-2-junak.pub@gmail.com> (raw)
In-Reply-To: <20201004081644.323858-1-junak.pub@gmail.com>

Add device tree bindings documentation for Qualcomm MSM8953
pinctrl driver.

Signed-off-by: Vladimir Lypak <junak.pub@gmail.com>
---
 .../pinctrl/qcom,msm8953-pinctrl.yaml         | 160 ++++++++++++++++++
 1 file changed, 160 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
new file mode 100644
index 000000000000..e539149834b6
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
@@ -0,0 +1,160 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,msm8953-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. MSM8953 TLMM block
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: |
+  This binding describes the Top Level Mode Multiplexer block found in the
+  MSM8953 platform.
+
+properties:
+  compatible:
+    const: qcom,msm8953-pinctrl
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    description: Specifies the TLMM summary IRQ
+    maxItems: 1
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    description:
+      Specifies the PIN numbers and Flags, as defined in defined in
+      include/dt-bindings/interrupt-controller/irq.h
+    const: 2
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description: Specifying the pin number and flags, as defined in
+      include/dt-bindings/gpio/gpio.h
+    const: 2
+
+  gpio-ranges:
+    maxItems: 1
+
+  wakeup-parent:
+    maxItems: 1
+
+#PIN CONFIGURATION NODES
+patternProperties:
+  '^.*$':
+    if:
+      type: object
+    then:
+      properties:
+        pins:
+          description:
+            List of gpio pins affected by the properties specified in this
+            subnode.
+          items:
+            oneOf:
+              - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$"
+              - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk, sdc2_clk,
+                        sdc2_cmd, sdc2_data, qdsd_clk, qdsd_cmd, qdsd_data0,
+                        qdsd_data1, qdsd_data2, qdsd_data3 ]
+          minItems: 1
+          maxItems: 16
+
+        function:
+          description:
+            Specify the alternative function to be configured for the specified
+            pins.
+
+          enum: [ accel_int, adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1,
+                  atest_char, atest_char0, atest_char1, atest_char2, atest_char3,
+                  atest_gpsadc_dtest0_native, atest_gpsadc_dtest1_native, atest_tsens,
+                  atest_wlan0, atest_wlan1, bimc_dte0, bimc_dte1, blsp1_spi,
+                  blsp3_spi, blsp6_spi, blsp7_spi, blsp_i2c1, blsp_i2c2, blsp_i2c3,
+                  blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_spi1,
+                  blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7,
+                  blsp_spi8, blsp_uart2, blsp_uart4, blsp_uart5, blsp_uart6, cam0_ldo,
+                  cam1_ldo, cam1_rst, cam1_standby, cam2_rst, cam2_standby, cam3_rst,
+                  cam3_standby, cam_irq, cam_mclk, cap_int, cci_async, cci_i2c,
+                  cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
+                  cdc_pdm0, codec_int1, codec_int2, codec_reset, cri_trng, cri_trng0,
+                  cri_trng1, dac_calib0, dac_calib1, dac_calib10, dac_calib11,
+                  dac_calib12, dac_calib13, dac_calib14, dac_calib15, dac_calib16,
+                  dac_calib17, dac_calib18, dac_calib19, dac_calib2, dac_calib20,
+                  dac_calib21, dac_calib22, dac_calib23, dac_calib24, dac_calib25,
+                  dac_calib3, dac_calib4, dac_calib5, dac_calib6, dac_calib7,
+                  dac_calib8, dac_calib9, dbg_out, ddr_bist, dmic0_clk, dmic0_data,
+                  ebi_cdc, ebi_ch0, ext_lpass, flash_strobe, fp_int, gcc_gp1_clk_a,
+                  gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b, gcc_gp3_clk_a,
+                  gcc_gp3_clk_b, gcc_plltest, gcc_tlmm, gpio, gsm0_tx, gsm1_tx,
+                  gyro_int, hall_int, hdmi_int, key_focus, key_home, key_snapshot,
+                  key_volp, ldo_en, ldo_update, lpass_slimbus, lpass_slimbus0,
+                  lpass_slimbus1, m_voc, mag_int, mdp_vsync, mipi_dsi0, modem_tsync,
+                  mss_lte, nav_pps, nav_pps_in_a, nav_pps_in_b, nav_tsync,
+                  nfc_disable, nfc_dwl, nfc_irq, ois_sync, pa_indicator, pbs0, pbs1,
+                  pbs2, pressure_int, pri_mi2s, pri_mi2s_mclk_a, pri_mi2s_mclk_b,
+                  pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
+                  pwr_down, pwr_modem_enabled_a, pwr_modem_enabled_b,
+                  pwr_nav_enabled_a, pwr_nav_enabled_b, qdss_cti_trig_in_a0,
+                  qdss_cti_trig_in_a1, qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
+                  qdss_cti_trig_out_a0, qdss_cti_trig_out_a1, qdss_cti_trig_out_b0,
+                  qdss_cti_trig_out_b1, qdss_traceclk_a, qdss_traceclk_b,
+                  qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a,
+                  qdss_tracedata_b, sd_write, sdcard_det, sec_mi2s, sec_mi2s_mclk_a,
+                  sec_mi2s_mclk_b, smb_int, ss_switch, ssbi_wtr1, ts_resout,
+                  ts_sample, ts_xvdd, tsens_max, uim1_clk, uim1_data, uim1_present,
+                  uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset,
+                  uim_batt, us_emitter, us_euro, wcss_bt, wcss_fm, wcss_wlan,
+                  wcss_wlan0, wcss_wlan1, wcss_wlan2, wsa_en, wsa_io, wsa_irq ]
+
+        drive-strength:
+          enum: [2, 4, 6, 8, 10, 12, 14, 16]
+          default: 2
+          description:
+            Selects the drive strength for the specified pins, in mA.
+
+        bias-pull-down: true
+
+        bias-pull-up: true
+
+        bias-disable: true
+
+        output-high: true
+
+        output-low: true
+
+      required:
+        - pins
+        - function
+
+      additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-controller
+  - '#interrupt-cells'
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+additionalProperties: false
+
+examples:
+  - |
+        #include <dt-bindings/interrupt-controller/arm-gic.h>
+        tlmm: pinctrl@1000000 {
+              compatible = "qcom,msm8953-pinctrl";
+              reg = <0x01000000 0x300000>;
+              interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+              interrupt-controller;
+              #interrupt-cells = <2>;
+              gpio-controller;
+              #gpio-cells = <2>;
+              gpio-ranges = <&tlmm 0 0 142>;
+        };
-- 
2.24.1


  reply	other threads:[~2020-10-04  8:34 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-10-04  8:16 [PATCH 1/2] pinctrl: qcom: add pinctrl driver for msm8953 Vladimir Lypak
2020-10-04  8:16 ` Vladimir Lypak [this message]
2020-10-06 21:22   ` [PATCH 2/2] dt-bindings: pinctrl: qcom: add msm8953 pinctrl bindings Rob Herring
2020-10-07 12:08     ` Vladirmir Lisak

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201004081644.323858-2-junak.pub@gmail.com \
    --to=junak.pub@gmail.com \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --subject='Re: [PATCH 2/2] dt-bindings: pinctrl: qcom: add msm8953 pinctrl bindings' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).