[PATCH 0/2] ARM: dts: qcom: sdx65: support IPA

[PATCH 0/2] ARM: dts: qcom: sdx65: support IPA

[Alex Elder]

The upstream IPA driver now supports IPA v5.0 for SDX65.  Add
IPA-related nodes and definitions to "sdx65.dtsi", and enable IPA
in "sdx65-mtp.dts".

Having touched these files, Konrad advised I should update them to
move the "status" property to the end of nodes where it is used.

					-Alex

Alex Elder (2):
  ARM: dts: qcom: sdx65: add IPA information
  ARM: dts: qcom-sdx65: move status properties to end of nodes

 arch/arm/boot/dts/qcom-sdx65-mtp.dts | 11 +++++--
 arch/arm/boot/dts/qcom-sdx65.dtsi    | 46 ++++++++++++++++++++++++++--
 2 files changed, 51 insertions(+), 6 deletions(-)

-- 
2.34.1

[PATCH 1/2] ARM: dts: qcom: sdx65: add IPA information

[Alex Elder]

Add IPA-related nodes and definitions to "sdx65.dtsi".  The SMP2P
nodes (ipa_smp2p_out and ipa_smp2p_in) are already present.

Enable IPA in "sdx65-mtp.dts"; this GSI firmware is loaded by Trust
Zone on this platform.

Tested-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Signed-off-by: Alex Elder <elder@linaro.org>
---
 arch/arm/boot/dts/qcom-sdx65-mtp.dts |  5 ++++
 arch/arm/boot/dts/qcom-sdx65.dtsi    | 38 ++++++++++++++++++++++++++++
 2 files changed, 43 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
index ed98c83c141fc..72e25de0db5fc 100644
--- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
+++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
@@ -245,6 +245,11 @@ &blsp1_uart3 {
 	status = "okay";
 };
 
+&ipa {
+	qcom,gsi-loader = "skip";
+	status = "okay";
+};
+
 &qpic_bam {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
index 192f9f94bc8b4..360d6dc144811 100644
--- a/arch/arm/boot/dts/qcom-sdx65.dtsi
+++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/interconnect/qcom,sdx65.h>
 
 / {
 	#address-cells = <1>;
@@ -299,6 +300,43 @@ tcsr_mutex: hwlock@1f40000 {
 			#hwlock-cells = <1>;
 		};
 
+		ipa: ipa@3e04000 {
+			compatible = "qcom,sdx65-ipa";
+
+			iommus = <&apps_smmu 0x5e0 0x0>,
+				 <&apps_smmu 0x5e2 0x0>;
+			reg = <0x3f40000 0x10000>,
+			      <0x3f50000 0x5000>,
+			      <0x3e04000 0xfc000>;
+			reg-names = "ipa-reg",
+				    "ipa-shared",
+				    "gsi";
+
+			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
+					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ipa",
+					   "gsi",
+					   "ipa-clock-query",
+					   "ipa-setup-ready";
+
+			clocks = <&rpmhcc RPMH_IPA_CLK>;
+			clock-names = "core";
+
+			interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI1>,
+					<&mem_noc MASTER_APPSS_PROC &system_noc SLAVE_IPA_CFG>;
+			interconnect-names = "memory",
+					     "config";
+
+			qcom,smem-states = <&ipa_smp2p_out 0>,
+					   <&ipa_smp2p_out 1>;
+			qcom,smem-state-names = "ipa-clock-enabled-valid",
+						"ipa-clock-enabled";
+
+			status = "disabled";
+		};
+
 		remoteproc_mpss: remoteproc@4080000 {
 			compatible = "qcom,sdx55-mpss-pas";
 			reg = <0x04080000 0x4040>;
-- 
2.34.1

[PATCH 2/2] ARM: dts: qcom-sdx65: move status properties to end of nodes

[Alex Elder]

Move a few device tree "status" properties so that they are the last
specified property, in "qcom-sdx65-mtp.dts" and "qcom-sdx65.dtsi".
Note that properties must always be specified before sub-nodes.

Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
---
 arch/arm/boot/dts/qcom-sdx65-mtp.dts | 6 +++---
 arch/arm/boot/dts/qcom-sdx65.dtsi    | 8 +++++---
 2 files changed, 8 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
index 72e25de0db5fc..57bc3b03d3aac 100644
--- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
+++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
@@ -270,8 +270,8 @@ nand@0 {
 };
 
 &remoteproc_mpss {
-	status = "okay";
 	memory-region = <&mpss_adsp_mem>;
+	status = "okay";
 };
 
 &usb {
@@ -283,14 +283,14 @@ &usb_dwc3 {
 };
 
 &usb_hsphy {
-	status = "okay";
 	vdda-pll-supply = <&vreg_l4b_0p88>;
 	vdda33-supply = <&vreg_l10b_3p08>;
 	vdda18-supply = <&vreg_l5b_1p8>;
+	status = "okay";
 };
 
 &usb_qmpphy {
-	status = "okay";
 	vdda-phy-supply = <&vreg_l4b_0p88>;
 	vdda-pll-supply = <&vreg_l1b_1p2>;
+	status = "okay";
 };
diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
index 360d6dc144811..a7adf28a395a8 100644
--- a/arch/arm/boot/dts/qcom-sdx65.dtsi
+++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
@@ -224,16 +224,15 @@ usb_hsphy: phy@ff4000 {
 				     "qcom,usb-snps-hs-7nm-phy";
 			reg = <0xff4000 0x120>;
 			#phy-cells = <0>;
-			status = "disabled";
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "ref";
 			resets = <&gcc GCC_QUSB2PHY_BCR>;
+			status = "disabled";
 		};
 
 		usb_qmpphy: phy@ff6000 {
 			compatible = "qcom,sdx65-qmp-usb3-uni-phy";
 			reg = <0x00ff6000 0x1c8>;
-			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -247,6 +246,8 @@ usb_qmpphy: phy@ff6000 {
 				 <&gcc GCC_USB3_PHY_BCR>;
 			reset-names = "phy", "common";
 
+			status = "disabled";
+
 			usb_ssphy: phy@ff6200 {
 				reg = <0x00ff6e00 0x160>,
 				      <0x00ff7000 0x1ec>,
@@ -393,7 +394,6 @@ mem_noc: interconnect@9680000 {
 		usb: usb@a6f8800 {
 			compatible = "qcom,sdx65-dwc3", "qcom,dwc3";
 			reg = <0x0a6f8800 0x400>;
-			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -423,6 +423,8 @@ usb: usb@a6f8800 {
 
 			resets = <&gcc GCC_USB30_BCR>;
 
+			status = "disabled";
+
 			usb_dwc3: usb@a600000 {
 				compatible = "snps,dwc3";
 				reg = <0x0a600000 0xcd00>;
-- 
2.34.1

Re: [PATCH 1/2] ARM: dts: qcom: sdx65: add IPA information

[Krzysztof Kozlowski]

On 24/03/2023 21:15, Alex Elder wrote:
> Add IPA-related nodes and definitions to "sdx65.dtsi".  The SMP2P
> nodes (ipa_smp2p_out and ipa_smp2p_in) are already present.
> 
> Enable IPA in "sdx65-mtp.dts"; this GSI firmware is loaded by Trust
> Zone on this platform.
> 
> Tested-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
> Signed-off-by: Alex Elder <elder@linaro.org>
> ---
>  arch/arm/boot/dts/qcom-sdx65-mtp.dts |  5 ++++
>  arch/arm/boot/dts/qcom-sdx65.dtsi    | 38 ++++++++++++++++++++++++++++
>  2 files changed, 43 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
> index ed98c83c141fc..72e25de0db5fc 100644
> --- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
> +++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
> @@ -245,6 +245,11 @@ &blsp1_uart3 {
>  	status = "okay";
>  };
>  
> +&ipa {
> +	qcom,gsi-loader = "skip";
> +	status = "okay";
> +};
> +
>  &qpic_bam {
>  	status = "okay";
>  };
> diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
> index 192f9f94bc8b4..360d6dc144811 100644
> --- a/arch/arm/boot/dts/qcom-sdx65.dtsi
> +++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
> @@ -11,6 +11,7 @@
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/power/qcom-rpmpd.h>
>  #include <dt-bindings/soc/qcom,rpmh-rsc.h>
> +#include <dt-bindings/interconnect/qcom,sdx65.h>
>  
>  / {
>  	#address-cells = <1>;
> @@ -299,6 +300,43 @@ tcsr_mutex: hwlock@1f40000 {
>  			#hwlock-cells = <1>;
>  		};
>  
> +		ipa: ipa@3e04000 {
> +			compatible = "qcom,sdx65-ipa";
> +
> +			iommus = <&apps_smmu 0x5e0 0x0>,
> +				 <&apps_smmu 0x5e2 0x0>;
> +			reg = <0x3f40000 0x10000>,
> +			      <0x3f50000 0x5000>,
> +			      <0x3e04000 0xfc000>;
> +			reg-names = "ipa-reg",
> +				    "ipa-shared",
> +				    "gsi";
> +
> +			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
> +					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> +					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "ipa",
> +					   "gsi",
> +					   "ipa-clock-query",
> +					   "ipa-setup-ready";

These look misaligned.

With above:

Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>


Best regards,
Krzysztof

Re: [PATCH 1/2] ARM: dts: qcom: sdx65: add IPA information

[Konrad Dybcio]

On 25.03.2023 12:14, Krzysztof Kozlowski wrote:
> On 24/03/2023 21:15, Alex Elder wrote:
>> Add IPA-related nodes and definitions to "sdx65.dtsi".  The SMP2P
>> nodes (ipa_smp2p_out and ipa_smp2p_in) are already present.
>>
>> Enable IPA in "sdx65-mtp.dts"; this GSI firmware is loaded by Trust
>> Zone on this platform.
>>
>> Tested-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
>> Signed-off-by: Alex Elder <elder@linaro.org>
>> ---
>>  arch/arm/boot/dts/qcom-sdx65-mtp.dts |  5 ++++
>>  arch/arm/boot/dts/qcom-sdx65.dtsi    | 38 ++++++++++++++++++++++++++++
>>  2 files changed, 43 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>> index ed98c83c141fc..72e25de0db5fc 100644
>> --- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>> +++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>> @@ -245,6 +245,11 @@ &blsp1_uart3 {
>>  	status = "okay";
>>  };
>>  
>> +&ipa {
>> +	qcom,gsi-loader = "skip";
>> +	status = "okay";
>> +};
>> +
>>  &qpic_bam {
>>  	status = "okay";
>>  };
>> diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
>> index 192f9f94bc8b4..360d6dc144811 100644
>> --- a/arch/arm/boot/dts/qcom-sdx65.dtsi
>> +++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
>> @@ -11,6 +11,7 @@
>>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>>  #include <dt-bindings/power/qcom-rpmpd.h>
>>  #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>> +#include <dt-bindings/interconnect/qcom,sdx65.h>
>>  
>>  / {
>>  	#address-cells = <1>;
>> @@ -299,6 +300,43 @@ tcsr_mutex: hwlock@1f40000 {
>>  			#hwlock-cells = <1>;
>>  		};
>>  
>> +		ipa: ipa@3e04000 {
>> +			compatible = "qcom,sdx65-ipa";
>> +
>> +			iommus = <&apps_smmu 0x5e0 0x0>,
>> +				 <&apps_smmu 0x5e2 0x0>;
>> +			reg = <0x3f40000 0x10000>,
>> +			      <0x3f50000 0x5000>,
>> +			      <0x3e04000 0xfc000>;
>> +			reg-names = "ipa-reg",
>> +				    "ipa-shared",
>> +				    "gsi";
>> +
>> +			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
>> +					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
>> +					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>> +					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
>> +			interrupt-names = "ipa",
>> +					   "gsi",
>> +					   "ipa-clock-query",
>> +					   "ipa-setup-ready";
> 
> These look misaligned.
> 
> With above:
> 
> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
With this and moving iommus below interconnect:

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
> 
> 
> Best regards,
> Krzysztof
> 

Re: [PATCH 2/2] ARM: dts: qcom-sdx65: move status properties to end of nodes

[Konrad Dybcio]

On 24.03.2023 21:15, Alex Elder wrote:
> Move a few device tree "status" properties so that they are the last
> specified property, in "qcom-sdx65-mtp.dts" and "qcom-sdx65.dtsi".
> Note that properties must always be specified before sub-nodes.
> 
> Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> Signed-off-by: Alex Elder <elder@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  arch/arm/boot/dts/qcom-sdx65-mtp.dts | 6 +++---
>  arch/arm/boot/dts/qcom-sdx65.dtsi    | 8 +++++---
>  2 files changed, 8 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
> index 72e25de0db5fc..57bc3b03d3aac 100644
> --- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
> +++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
> @@ -270,8 +270,8 @@ nand@0 {
>  };
>  
>  &remoteproc_mpss {
> -	status = "okay";
>  	memory-region = <&mpss_adsp_mem>;
> +	status = "okay";
>  };
>  
>  &usb {
> @@ -283,14 +283,14 @@ &usb_dwc3 {
>  };
>  
>  &usb_hsphy {
> -	status = "okay";
>  	vdda-pll-supply = <&vreg_l4b_0p88>;
>  	vdda33-supply = <&vreg_l10b_3p08>;
>  	vdda18-supply = <&vreg_l5b_1p8>;
> +	status = "okay";
>  };
>  
>  &usb_qmpphy {
> -	status = "okay";
>  	vdda-phy-supply = <&vreg_l4b_0p88>;
>  	vdda-pll-supply = <&vreg_l1b_1p2>;
> +	status = "okay";
>  };
> diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
> index 360d6dc144811..a7adf28a395a8 100644
> --- a/arch/arm/boot/dts/qcom-sdx65.dtsi
> +++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
> @@ -224,16 +224,15 @@ usb_hsphy: phy@ff4000 {
>  				     "qcom,usb-snps-hs-7nm-phy";
>  			reg = <0xff4000 0x120>;
>  			#phy-cells = <0>;
> -			status = "disabled";
>  			clocks = <&rpmhcc RPMH_CXO_CLK>;
>  			clock-names = "ref";
>  			resets = <&gcc GCC_QUSB2PHY_BCR>;
> +			status = "disabled";
>  		};
>  
>  		usb_qmpphy: phy@ff6000 {
>  			compatible = "qcom,sdx65-qmp-usb3-uni-phy";
>  			reg = <0x00ff6000 0x1c8>;
> -			status = "disabled";
>  			#address-cells = <1>;
>  			#size-cells = <1>;
>  			ranges;
> @@ -247,6 +246,8 @@ usb_qmpphy: phy@ff6000 {
>  				 <&gcc GCC_USB3_PHY_BCR>;
>  			reset-names = "phy", "common";
>  
> +			status = "disabled";
> +
>  			usb_ssphy: phy@ff6200 {
>  				reg = <0x00ff6e00 0x160>,
>  				      <0x00ff7000 0x1ec>,
> @@ -393,7 +394,6 @@ mem_noc: interconnect@9680000 {
>  		usb: usb@a6f8800 {
>  			compatible = "qcom,sdx65-dwc3", "qcom,dwc3";
>  			reg = <0x0a6f8800 0x400>;
> -			status = "disabled";
>  			#address-cells = <1>;
>  			#size-cells = <1>;
>  			ranges;
> @@ -423,6 +423,8 @@ usb: usb@a6f8800 {
>  
>  			resets = <&gcc GCC_USB30_BCR>;
>  
> +			status = "disabled";
> +
>  			usb_dwc3: usb@a600000 {
>  				compatible = "snps,dwc3";
>  				reg = <0x0a600000 0xcd00>;

Re: [PATCH 1/2] ARM: dts: qcom: sdx65: add IPA information

[Alex Elder]

On 3/25/23 6:14 AM, Krzysztof Kozlowski wrote:
> On 24/03/2023 21:15, Alex Elder wrote:
>> Add IPA-related nodes and definitions to "sdx65.dtsi".  The SMP2P
>> nodes (ipa_smp2p_out and ipa_smp2p_in) are already present.
>>
>> Enable IPA in "sdx65-mtp.dts"; this GSI firmware is loaded by Trust
>> Zone on this platform.
>>
>> Tested-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
>> Signed-off-by: Alex Elder <elder@linaro.org>
>> ---
>>   arch/arm/boot/dts/qcom-sdx65-mtp.dts |  5 ++++
>>   arch/arm/boot/dts/qcom-sdx65.dtsi    | 38 ++++++++++++++++++++++++++++
>>   2 files changed, 43 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>> index ed98c83c141fc..72e25de0db5fc 100644
>> --- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>> +++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>> @@ -245,6 +245,11 @@ &blsp1_uart3 {
>>   	status = "okay";
>>   };
>>   
>> +&ipa {
>> +	qcom,gsi-loader = "skip";
>> +	status = "okay";
>> +};
>> +
>>   &qpic_bam {
>>   	status = "okay";
>>   };
>> diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
>> index 192f9f94bc8b4..360d6dc144811 100644
>> --- a/arch/arm/boot/dts/qcom-sdx65.dtsi
>> +++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
>> @@ -11,6 +11,7 @@
>>   #include <dt-bindings/interrupt-controller/arm-gic.h>
>>   #include <dt-bindings/power/qcom-rpmpd.h>
>>   #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>> +#include <dt-bindings/interconnect/qcom,sdx65.h>
>>   
>>   / {
>>   	#address-cells = <1>;
>> @@ -299,6 +300,43 @@ tcsr_mutex: hwlock@1f40000 {
>>   			#hwlock-cells = <1>;
>>   		};
>>   
>> +		ipa: ipa@3e04000 {
>> +			compatible = "qcom,sdx65-ipa";
>> +
>> +			iommus = <&apps_smmu 0x5e0 0x0>,
>> +				 <&apps_smmu 0x5e2 0x0>;
>> +			reg = <0x3f40000 0x10000>,
>> +			      <0x3f50000 0x5000>,
>> +			      <0x3e04000 0xfc000>;
>> +			reg-names = "ipa-reg",
>> +				    "ipa-shared",
>> +				    "gsi";
>> +
>> +			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
>> +					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
>> +					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>> +					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
>> +			interrupt-names = "ipa",
>> +					   "gsi",
>> +					   "ipa-clock-query",
>> +					   "ipa-setup-ready";
> 
> These look misaligned.

I believe this is the alignment convention used by all IPA nodes
in DTS files.  It's possible I'm not seeing something you are,
but...  what alignment should be used?  And if I change this,
should I change all others?

Thanks.

					-Alex

> 
> With above:
> 
> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
> 
> 
> Best regards,
> Krzysztof
> 

Re: [PATCH 1/2] ARM: dts: qcom: sdx65: add IPA information

[Krzysztof Kozlowski]

On 26/03/2023 18:01, Alex Elder wrote:
> On 3/25/23 6:14 AM, Krzysztof Kozlowski wrote:
>> On 24/03/2023 21:15, Alex Elder wrote:
>>> Add IPA-related nodes and definitions to "sdx65.dtsi".  The SMP2P
>>> nodes (ipa_smp2p_out and ipa_smp2p_in) are already present.
>>>
>>> Enable IPA in "sdx65-mtp.dts"; this GSI firmware is loaded by Trust
>>> Zone on this platform.
>>>
>>> Tested-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
>>> Signed-off-by: Alex Elder <elder@linaro.org>
>>> ---
>>>   arch/arm/boot/dts/qcom-sdx65-mtp.dts |  5 ++++
>>>   arch/arm/boot/dts/qcom-sdx65.dtsi    | 38 ++++++++++++++++++++++++++++
>>>   2 files changed, 43 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>> index ed98c83c141fc..72e25de0db5fc 100644
>>> --- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>> +++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>> @@ -245,6 +245,11 @@ &blsp1_uart3 {
>>>   	status = "okay";
>>>   };
>>>   
>>> +&ipa {
>>> +	qcom,gsi-loader = "skip";
>>> +	status = "okay";
>>> +};
>>> +
>>>   &qpic_bam {
>>>   	status = "okay";
>>>   };
>>> diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
>>> index 192f9f94bc8b4..360d6dc144811 100644
>>> --- a/arch/arm/boot/dts/qcom-sdx65.dtsi
>>> +++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
>>> @@ -11,6 +11,7 @@
>>>   #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>   #include <dt-bindings/power/qcom-rpmpd.h>
>>>   #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>>> +#include <dt-bindings/interconnect/qcom,sdx65.h>
>>>   
>>>   / {
>>>   	#address-cells = <1>;
>>> @@ -299,6 +300,43 @@ tcsr_mutex: hwlock@1f40000 {
>>>   			#hwlock-cells = <1>;
>>>   		};
>>>   
>>> +		ipa: ipa@3e04000 {
>>> +			compatible = "qcom,sdx65-ipa";
>>> +
>>> +			iommus = <&apps_smmu 0x5e0 0x0>,
>>> +				 <&apps_smmu 0x5e2 0x0>;
>>> +			reg = <0x3f40000 0x10000>,
>>> +			      <0x3f50000 0x5000>,
>>> +			      <0x3e04000 0xfc000>;
>>> +			reg-names = "ipa-reg",
>>> +				    "ipa-shared",
>>> +				    "gsi";
>>> +
>>> +			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
>>> +					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
>>> +					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>>> +					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
>>> +			interrupt-names = "ipa",
>>> +					   "gsi",
>>> +					   "ipa-clock-query",
>>> +					   "ipa-setup-ready";
>>
>> These look misaligned.
> 
> I believe this is the alignment convention used by all IPA nodes
> in DTS files.  It's possible I'm not seeing something you are,
> but...  what alignment should be used?  And if I change this,
> should I change all others?

If this is aligned, then fine. The diff points it is not, but the diff
might be a bit tricky sometimes.

Alignment is till " in previous line. For example sdm845 looks fine.


Best regards,
Krzysztof

Re: [PATCH 1/2] ARM: dts: qcom: sdx65: add IPA information

[Alex Elder]

On 3/25/23 7:12 AM, Konrad Dybcio wrote:
> 
> 
> On 25.03.2023 12:14, Krzysztof Kozlowski wrote:
>> On 24/03/2023 21:15, Alex Elder wrote:
>>> Add IPA-related nodes and definitions to "sdx65.dtsi".  The SMP2P
>>> nodes (ipa_smp2p_out and ipa_smp2p_in) are already present.
>>>
>>> Enable IPA in "sdx65-mtp.dts"; this GSI firmware is loaded by Trust
>>> Zone on this platform.
>>>
>>> Tested-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
>>> Signed-off-by: Alex Elder <elder@linaro.org>
>>> ---
>>>   arch/arm/boot/dts/qcom-sdx65-mtp.dts |  5 ++++
>>>   arch/arm/boot/dts/qcom-sdx65.dtsi    | 38 ++++++++++++++++++++++++++++
>>>   2 files changed, 43 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>> index ed98c83c141fc..72e25de0db5fc 100644
>>> --- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>> +++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>> @@ -245,6 +245,11 @@ &blsp1_uart3 {
>>>   	status = "okay";
>>>   };
>>>   
>>> +&ipa {
>>> +	qcom,gsi-loader = "skip";
>>> +	status = "okay";
>>> +};
>>> +
>>>   &qpic_bam {
>>>   	status = "okay";
>>>   };
>>> diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
>>> index 192f9f94bc8b4..360d6dc144811 100644
>>> --- a/arch/arm/boot/dts/qcom-sdx65.dtsi
>>> +++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
>>> @@ -11,6 +11,7 @@
>>>   #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>   #include <dt-bindings/power/qcom-rpmpd.h>
>>>   #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>>> +#include <dt-bindings/interconnect/qcom,sdx65.h>
>>>   
>>>   / {
>>>   	#address-cells = <1>;
>>> @@ -299,6 +300,43 @@ tcsr_mutex: hwlock@1f40000 {
>>>   			#hwlock-cells = <1>;
>>>   		};
>>>   
>>> +		ipa: ipa@3e04000 {
>>> +			compatible = "qcom,sdx65-ipa";
>>> +
>>> +			iommus = <&apps_smmu 0x5e0 0x0>,
>>> +				 <&apps_smmu 0x5e2 0x0>;
>>> +			reg = <0x3f40000 0x10000>,
>>> +			      <0x3f50000 0x5000>,
>>> +			      <0x3e04000 0xfc000>;
>>> +			reg-names = "ipa-reg",
>>> +				    "ipa-shared",
>>> +				    "gsi";
>>> +
>>> +			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
>>> +					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
>>> +					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>>> +					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
>>> +			interrupt-names = "ipa",
>>> +					   "gsi",
>>> +					   "ipa-clock-query",
>>> +					   "ipa-setup-ready";
>>
>> These look misaligned.
>>
>> With above:
>>
>> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
> With this and moving iommus below interconnect:

Is there guidance somewhere that states what order should be
used for these properties?  Why should iommus be below
interconnects?

As I said to Krzysztof, I *think* all of the IPA nodes look
like this; should all of them be updated to follow whatever
the preferred convention is?

Thanks.

					-Alex


> 
> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> 
> Konrad
>>
>>
>> Best regards,
>> Krzysztof
>>

Re: [PATCH 1/2] ARM: dts: qcom: sdx65: add IPA information

[Alex Elder]

On 3/26/23 11:04 AM, Krzysztof Kozlowski wrote:
> On 26/03/2023 18:01, Alex Elder wrote:
>> On 3/25/23 6:14 AM, Krzysztof Kozlowski wrote:
>>> On 24/03/2023 21:15, Alex Elder wrote:
>>>> Add IPA-related nodes and definitions to "sdx65.dtsi".  The SMP2P
>>>> nodes (ipa_smp2p_out and ipa_smp2p_in) are already present.
>>>>
>>>> Enable IPA in "sdx65-mtp.dts"; this GSI firmware is loaded by Trust
>>>> Zone on this platform.
>>>>
>>>> Tested-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
>>>> Signed-off-by: Alex Elder <elder@linaro.org>
>>>> ---
>>>>    arch/arm/boot/dts/qcom-sdx65-mtp.dts |  5 ++++
>>>>    arch/arm/boot/dts/qcom-sdx65.dtsi    | 38 ++++++++++++++++++++++++++++
>>>>    2 files changed, 43 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>>> index ed98c83c141fc..72e25de0db5fc 100644
>>>> --- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>>> +++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>>> @@ -245,6 +245,11 @@ &blsp1_uart3 {
>>>>    	status = "okay";
>>>>    };
>>>>    
>>>> +&ipa {
>>>> +	qcom,gsi-loader = "skip";
>>>> +	status = "okay";
>>>> +};
>>>> +
>>>>    &qpic_bam {
>>>>    	status = "okay";
>>>>    };
>>>> diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
>>>> index 192f9f94bc8b4..360d6dc144811 100644
>>>> --- a/arch/arm/boot/dts/qcom-sdx65.dtsi
>>>> +++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
>>>> @@ -11,6 +11,7 @@
>>>>    #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>>    #include <dt-bindings/power/qcom-rpmpd.h>
>>>>    #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>>>> +#include <dt-bindings/interconnect/qcom,sdx65.h>
>>>>    
>>>>    / {
>>>>    	#address-cells = <1>;
>>>> @@ -299,6 +300,43 @@ tcsr_mutex: hwlock@1f40000 {
>>>>    			#hwlock-cells = <1>;
>>>>    		};
>>>>    
>>>> +		ipa: ipa@3e04000 {
>>>> +			compatible = "qcom,sdx65-ipa";
>>>> +
>>>> +			iommus = <&apps_smmu 0x5e0 0x0>,
>>>> +				 <&apps_smmu 0x5e2 0x0>;
>>>> +			reg = <0x3f40000 0x10000>,
>>>> +			      <0x3f50000 0x5000>,
>>>> +			      <0x3e04000 0xfc000>;
>>>> +			reg-names = "ipa-reg",
>>>> +				    "ipa-shared",
>>>> +				    "gsi";
>>>> +
>>>> +			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
>>>> +					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
>>>> +					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>>>> +					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
>>>> +			interrupt-names = "ipa",
>>>> +					   "gsi",
>>>> +					   "ipa-clock-query",
>>>> +					   "ipa-setup-ready";
>>>
>>> These look misaligned.
>>
>> I believe this is the alignment convention used by all IPA nodes
>> in DTS files.  It's possible I'm not seeing something you are,
>> but...  what alignment should be used?  And if I change this,
>> should I change all others?
> 
> If this is aligned, then fine. The diff points it is not, but the diff
> might be a bit tricky sometimes.
> 
> Alignment is till " in previous line. For example sdm845 looks fine.

OK thank you.  I will send v2 of this series after I hear back
from Konrad, adding your reviewed-by, and will double-check
the alignment as well.

					-Alex

> 
> 
> Best regards,
> Krzysztof
> 

Re: [PATCH 1/2] ARM: dts: qcom: sdx65: add IPA information

[Konrad Dybcio]

On 26.03.2023 18:04, Alex Elder wrote:
> On 3/25/23 7:12 AM, Konrad Dybcio wrote:
>>
>>
>> On 25.03.2023 12:14, Krzysztof Kozlowski wrote:
>>> On 24/03/2023 21:15, Alex Elder wrote:
>>>> Add IPA-related nodes and definitions to "sdx65.dtsi".  The SMP2P
>>>> nodes (ipa_smp2p_out and ipa_smp2p_in) are already present.
>>>>
>>>> Enable IPA in "sdx65-mtp.dts"; this GSI firmware is loaded by Trust
>>>> Zone on this platform.
>>>>
>>>> Tested-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
>>>> Signed-off-by: Alex Elder <elder@linaro.org>
>>>> ---
>>>>   arch/arm/boot/dts/qcom-sdx65-mtp.dts |  5 ++++
>>>>   arch/arm/boot/dts/qcom-sdx65.dtsi    | 38 ++++++++++++++++++++++++++++
>>>>   2 files changed, 43 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>>> index ed98c83c141fc..72e25de0db5fc 100644
>>>> --- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>>> +++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
>>>> @@ -245,6 +245,11 @@ &blsp1_uart3 {
>>>>       status = "okay";
>>>>   };
>>>>   +&ipa {
>>>> +    qcom,gsi-loader = "skip";
>>>> +    status = "okay";
>>>> +};
>>>> +
>>>>   &qpic_bam {
>>>>       status = "okay";
>>>>   };
>>>> diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
>>>> index 192f9f94bc8b4..360d6dc144811 100644
>>>> --- a/arch/arm/boot/dts/qcom-sdx65.dtsi
>>>> +++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
>>>> @@ -11,6 +11,7 @@
>>>>   #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>>   #include <dt-bindings/power/qcom-rpmpd.h>
>>>>   #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>>>> +#include <dt-bindings/interconnect/qcom,sdx65.h>
>>>>     / {
>>>>       #address-cells = <1>;
>>>> @@ -299,6 +300,43 @@ tcsr_mutex: hwlock@1f40000 {
>>>>               #hwlock-cells = <1>;
>>>>           };
>>>>   +        ipa: ipa@3e04000 {
>>>> +            compatible = "qcom,sdx65-ipa";
>>>> +
>>>> +            iommus = <&apps_smmu 0x5e0 0x0>,
>>>> +                 <&apps_smmu 0x5e2 0x0>;
>>>> +            reg = <0x3f40000 0x10000>,
>>>> +                  <0x3f50000 0x5000>,
>>>> +                  <0x3e04000 0xfc000>;
>>>> +            reg-names = "ipa-reg",
>>>> +                    "ipa-shared",
>>>> +                    "gsi";
>>>> +
>>>> +            interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
>>>> +                          <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
>>>> +                          <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>>>> +                          <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
>>>> +            interrupt-names = "ipa",
>>>> +                       "gsi",
>>>> +                       "ipa-clock-query",
>>>> +                       "ipa-setup-ready";
>>>
>>> These look misaligned.
>>>
>>> With above:
>>>
>>> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
>> With this and moving iommus below interconnect:
> 
> Is there guidance somewhere that states what order should be
> used for these properties?
This is a very slippery topic, but..

 Why should iommus be below
> interconnects?
..everybody agrees iommus shouldn't between compatible and
reg (these two go first hand-in-hand) and most of our DTs
have it somewhere low, often below interconnect.

In a perfect world we'd have a computer taking care of this
but for now it remains an open question.

> 
> As I said to Krzysztof, I *think* all of the IPA nodes look
> like this; should all of them be updated to follow whatever
> the preferred convention is?
This is the ugly part of this, we don't have a solid,
widely-agreed-upon scheme of ordering properties other than
some loose guidelines (e.g. compatible, reg, ...,  status),
so I think it's not worth making extra noise in existing files
until figure it out.

Konrad
> 
> Thanks.
> 
>                     -Alex
> 
> 
>>
>> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>>
>> Konrad
>>>
>>>
>>> Best regards,
>>> Krzysztof
>>>
> 

Re: [PATCH 1/2] ARM: dts: qcom: sdx65: add IPA information

[Alex Elder]

On 3/27/23 3:57 AM, Konrad Dybcio wrote:
> so I think it's not worth making extra noise in existing files
> until figure it out.

In that case, would you be OK if I leave this consistent
with the rest, and once it's figured out, I'll fix them
all at once?

					-Alex