From: Andrey Konovalov <andrey.konovalov@linaro.org>
To: Rob Herring <robh@kernel.org>
Cc: mchehab@kernel.org, linux-media@vger.kernel.org,
devicetree@vger.kernel.org, peter.griffin@linaro.org,
ezequiel@collabora.com
Subject: Re: [PATCH v2 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding
Date: Fri, 10 Jan 2020 23:18:03 +0300 [thread overview]
Message-ID: <530e69f9-cfda-5a4a-e5d5-42401ea74d32@linaro.org> (raw)
In-Reply-To: <20200104215322.GA548@bogus>
Hi Rob,
Thanks for the review!
On 05.01.2020 00:53, Rob Herring wrote:
> On Fri, Dec 27, 2019 at 03:21:13PM +0300, Andrey Konovalov wrote:
>> Add YAML device tree binding for IMX219 CMOS image sensor, and
>> the relevant MAINTAINERS entries.
>>
>> Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
>> ---
>> .../devicetree/bindings/media/i2c/imx219.yaml | 134 ++++++++++++++++++
>> MAINTAINERS | 8 ++
>> 2 files changed, 142 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/media/i2c/imx219.yaml b/Documentation/devicetree/bindings/media/i2c/imx219.yaml
>> new file mode 100644
>> index 000000000000..b58aa49a7c03
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/i2c/imx219.yaml
>> @@ -0,0 +1,134 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/media/i2c/imx219.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
>> +
>> +maintainers:
>> + - Dave Stevenson <dave.stevenson@raspberrypi.com>
>> +
>> +description: |-
>> + The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor
>> + with an active array size of 3280H x 2464V. It is programmable through
>> + I2C interface. The I2C address is fixed to 0x10 as per sensor data sheet.
>> + Image data is sent through MIPI CSI-2, which is configured as either 2 or
>> + 4 data lanes.
>> +
>> +properties:
>> + compatible:
>> + const: sony,imx219
>> +
>> + reg:
>> + description: I2C device address
>> + maxItems: 1
>> +
>> + clocks:
>> + maxItems: 1
>> +
>> + clock-names:
>> + items:
>> + - const: xclk
>> +
>> + VDIG-supply:
>> + description:
>> + Digital I/O voltage supply, 1.8 volts
>> +
>> + VANA-supply:
>> + description:
>> + Analog voltage supply, 2.8 volts
>> +
>> + VDDL-supply:
>> + description:
>> + Digital core voltage supply, 1.2 volts
>> +
>> + xclr-gpios:
>> + description: |-
>> + Reference to the GPIO connected to the xclr pin, if any.
>> + Must be released (set high) after all supplies are applied.
>> +
>> + camera-clk:
>> + type: object
>> +
>> + description: Clock source for imx219
>
> This clock is external to the sensor, so a node for a fixed clock should
> be too.
Done in v3.
>> +
>> + properties:
>> + clock-frequency: true
>> +
>> + required:
>> + - clock-frequency
>> +
>> + # See ../video-interfaces.txt for more details
>> + port:
>> + type: object
>> + properties:
>> + endpoint:
>> + type: object
>> + properties:
>> + clock-lanes:
>> + const: 0
>> +
>> + data-lanes:
>> + description: |-
>> + Should be <1 2> for two-lane operation, or <1 2 3 4> for
>> + four-lane operation.
>> + oneOf:
>> + - const: [[ 1, 2 ]]
>> + - const: [[ 1, 2, 3, 4 ]]
>
> Not sure if this actually works. If it does, it exposes how we encode
> the DT yaml format which we don't want to do here.
It does work - I am still not quite comfortable with json schema, and got
to the above by looking at the files produced by 'make dt_binding_check'.
> It should be:
>
> oneOf:
> - items:
> - const: 1
> - const: 2
> - items:
> - const: 1
> - const: 2
> - const: 3
> - const: 4
Thanks, got it.
> Really, I think you shouldn't need the 2nd case as that should be the
> default.
I've tried to implement that in v3 of the patch set.
Thanks,
Andrey
>> +
>> + clock-noncontinuous:
>> + type: boolean
>> + description: |-
>> + Presence of this boolean property decides whether the MIPI CSI-2
>> + clock is continuous or non-continuous.
>> +
>> + required:
>> + - clock-lanes
>> + - data-lanes
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - clocks
>> + - clock-names
>> + - VANA-supply
>> + - VDIG-supply
>> + - VDDL-supply
>> + - port
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> + - |
>> + i2c0 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + imx219: sensor@10 {
>> + compatible = "sony,imx219";
>> + reg = <0x10>;
>> + clocks = <&imx219_clk>;
>> + clock-names = "xclk";
>> + VANA-supply = <&imx219_vana>; /* 2.8v */
>> + VDIG-supply = <&imx219_vdig>; /* 1.8v */
>> + VDDL-supply = <&imx219_vddl>; /* 1.2v */
>> +
>> + imx219_clk: camera-clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <24000000>;
>> + };
>> +
>> + port {
>> + imx219_0: endpoint {
>> + remote-endpoint = <&csi1_ep>;
>> + clock-lanes = <0>;
>> + data-lanes = <1 2>;
>> + clock-noncontinuous;
>> + };
>> + };
>> + };
>> + };
>> +
>> +...
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index ffa3371bc750..f7b6c24ec081 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -15350,6 +15350,14 @@ S: Maintained
>> F: drivers/media/i2c/imx214.c
>> F: Documentation/devicetree/bindings/media/i2c/sony,imx214.txt
>>
>> +SONY IMX219 SENSOR DRIVER
>> +M: Dave Stevenson <dave.stevenson@raspberrypi.com>
>> +L: linux-media@vger.kernel.org
>> +T: git git://linuxtv.org/media_tree.git
>> +S: Maintained
>> +F: drivers/media/i2c/imx219.c
>> +F: Documentation/devicetree/bindings/media/i2c/imx219.yaml
>> +
>> SONY IMX258 SENSOR DRIVER
>> M: Sakari Ailus <sakari.ailus@linux.intel.com>
>> L: linux-media@vger.kernel.org
>> --
>> 2.17.1
>>
next prev parent reply other threads:[~2020-01-10 20:18 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-27 12:21 [PATCH v2 0/2] Add IMX219 CMOS image sensor support Andrey Konovalov
2019-12-27 12:21 ` [PATCH v2 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding Andrey Konovalov
2019-12-27 14:17 ` Sakari Ailus
2019-12-27 18:26 ` Andrey Konovalov
2019-12-30 9:24 ` Sakari Ailus
2020-01-06 14:56 ` Dave Stevenson
2020-01-04 21:53 ` Rob Herring
2020-01-10 20:18 ` Andrey Konovalov [this message]
2019-12-27 12:21 ` [PATCH v2 2/2] media: i2c: Add driver for Sony IMX219 sensor Andrey Konovalov
2019-12-27 14:55 ` Sakari Ailus
2020-01-13 19:16 ` Andrey Konovalov
2020-01-14 11:34 ` Dave Stevenson
2020-01-17 8:49 ` Sakari Ailus
2020-01-17 8:39 ` Sakari Ailus
2019-12-30 16:33 ` Ezequiel Garcia
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=530e69f9-cfda-5a4a-e5d5-42401ea74d32@linaro.org \
--to=andrey.konovalov@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=ezequiel@collabora.com \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=peter.griffin@linaro.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).