From: Rob Clark <robdclark@gmail.com>
To: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Sean Paul <sean@poorly.run>, Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
dri-devel <dri-devel@lists.freedesktop.org>,
linux-arm-msm <linux-arm-msm@vger.kernel.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Matthias Kaehlcke <mka@chromium.org>
Subject: Re: [PATCH v3 3/4] arm64: dts: sdm845: Add DSI and MDP OPP tables and power-domains
Date: Fri, 17 Jul 2020 10:47:51 -0700 [thread overview]
Message-ID: <CAF6AEGvioVKKSN-UP35OfJcfUXeHy34Y6w2eM_FZU+zpTaRE7A@mail.gmail.com> (raw)
In-Reply-To: <1594292674-15632-4-git-send-email-rnayak@codeaurora.org>
On Thu, Jul 9, 2020 at 4:05 AM Rajendra Nayak <rnayak@codeaurora.org> wrote:
>
> Add the OPP tables for DSI and MDP based on the perf state/clk
> requirements, and add the power-domains property to specify the
> scalable power domain.
>
> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Bjorn, the two driver patches are queued up in msm-next, I assume
you'll pickup the two dt patches?
BR,
-R
> ---
> arch/arm64/boot/dts/qcom/sdm845.dtsi | 59 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 59 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> index fee50d9..3efdd70 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -3296,6 +3296,35 @@
> #power-domain-cells = <1>;
> };
>
> + dsi_opp_table: dsi-opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-19200000 {
> + opp-hz = /bits/ 64 <19200000>;
> + required-opps = <&rpmhpd_opp_min_svs>;
> + };
> +
> + opp-180000000 {
> + opp-hz = /bits/ 64 <180000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-275000000 {
> + opp-hz = /bits/ 64 <275000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-328580000 {
> + opp-hz = /bits/ 64 <328580000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-358000000 {
> + opp-hz = /bits/ 64 <358000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> +
> mdss: mdss@ae00000 {
> compatible = "qcom,sdm845-mdss";
> reg = <0 0x0ae00000 0 0x1000>;
> @@ -3340,6 +3369,8 @@
> <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> assigned-clock-rates = <300000000>,
> <19200000>;
> + operating-points-v2 = <&mdp_opp_table>;
> + power-domains = <&rpmhpd SDM845_CX>;
>
> interrupt-parent = <&mdss>;
> interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> @@ -3364,6 +3395,30 @@
> };
> };
> };
> +
> + mdp_opp_table: mdp-opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-19200000 {
> + opp-hz = /bits/ 64 <19200000>;
> + required-opps = <&rpmhpd_opp_min_svs>;
> + };
> +
> + opp-171428571 {
> + opp-hz = /bits/ 64 <171428571>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-344000000 {
> + opp-hz = /bits/ 64 <344000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-430000000 {
> + opp-hz = /bits/ 64 <430000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> };
>
> dsi0: dsi@ae94000 {
> @@ -3386,6 +3441,8 @@
> "core",
> "iface",
> "bus";
> + operating-points-v2 = <&dsi_opp_table>;
> + power-domains = <&rpmhpd SDM845_CX>;
>
> phys = <&dsi0_phy>;
> phy-names = "dsi";
> @@ -3450,6 +3507,8 @@
> "core",
> "iface",
> "bus";
> + operating-points-v2 = <&dsi_opp_table>;
> + power-domains = <&rpmhpd SDM845_CX>;
>
> phys = <&dsi1_phy>;
> phy-names = "dsi";
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>
next prev parent reply other threads:[~2020-07-17 17:47 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-09 11:04 [PATCH v3 0/4] DVFS support for dpu and dsi Rajendra Nayak
2020-07-09 11:04 ` [PATCH v3 1/4] drm/msm/dpu: Use OPP API to set clk/perf state Rajendra Nayak
2020-07-09 11:04 ` [PATCH v3 2/4] drm/msm: dsi: " Rajendra Nayak
2020-07-09 11:04 ` [PATCH v3 3/4] arm64: dts: sdm845: Add DSI and MDP OPP tables and power-domains Rajendra Nayak
2020-07-17 17:47 ` Rob Clark [this message]
2020-07-09 11:04 ` [PATCH v3 4/4] arm64: dts: sc7180: " Rajendra Nayak
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAF6AEGvioVKKSN-UP35OfJcfUXeHy34Y6w2eM_FZU+zpTaRE7A@mail.gmail.com \
--to=robdclark@gmail.com \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mka@chromium.org \
--cc=rnayak@codeaurora.org \
--cc=sean@poorly.run \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).