From mboxrd@z Thu Jan 1 00:00:00 1970 From: "dbasehore ." Subject: Re: [PATCH v5 4/4] irqchip/gic-v3-its: add ability to resend MAPC on resume Date: Wed, 7 Feb 2018 16:00:53 -0800 Message-ID: References: <20180207014117.62611-1-dbasehore@chromium.org> <20180207014117.62611-5-dbasehore@chromium.org> <8276f426-e4a0-c400-9f87-31be3d6b1733@arm.com> <20180207232201.GB106856@ban.mtv.corp.google.com> Mime-Version: 1.0 Content-Type: text/plain; charset="UTF-8" Return-path: In-Reply-To: <20180207232201.GB106856@ban.mtv.corp.google.com> Sender: linux-pm-owner@vger.kernel.org To: Brian Norris Cc: Marc Zyngier , linux-kernel , Soby Mathew , Sudeep Holla , devicetree@vger.kernel.org, robh+dt@kernel.org, Mark Rutland , Linux-pm mailing list , "Wysocki, Rafael J" , Thomas Gleixner List-Id: devicetree@vger.kernel.org On Wed, Feb 7, 2018 at 3:22 PM, Brian Norris wrote: > Hi Marc, > > I'm really not an expert on this, so take my observations with a large > grain of salt: > > On Wed, Feb 07, 2018 at 08:46:42AM +0000, Marc Zyngier wrote: >> On 07/02/18 01:41, Derek Basehore wrote: >> > This adds functionality to resend the MAPC command to an ITS node on >> > resume. If the ITS is powered down during suspend and the collections >> > are not backed by memory, the ITS will lose that state. This just sets >> > up the known state for the collections after the ITS is restored. >> > >> > This is enabled via the reset-on-suspend flag in the DTS for an ITS >> > that has a non-zero number of collections stored in it. >> > >> > Signed-off-by: Derek Basehore >> > --- >> > drivers/irqchip/irq-gic-v3-its.c | 80 ++++++++++++++++++++------------------ >> > include/linux/irqchip/arm-gic-v3.h | 1 + >> > 2 files changed, 43 insertions(+), 38 deletions(-) >> > >> > diff --git a/drivers/irqchip/irq-gic-v3-its.c b/drivers/irqchip/irq-gic-v3-its.c >> > index 5e63635e2a7b..dd6cd6e68ed0 100644 >> > --- a/drivers/irqchip/irq-gic-v3-its.c >> > +++ b/drivers/irqchip/irq-gic-v3-its.c >> > @@ -1942,52 +1942,53 @@ static void its_cpu_init_lpis(void) >> > dsb(sy); >> > } >> > >> > -static void its_cpu_init_collection(void) >> > +static void its_cpu_init_collection(struct its_node *its) > > ... > >> > @@ -3127,6 +3128,9 @@ static void its_restore_enable(void) >> > its_write_baser(its, baser, baser->val); >> > } >> > writel_relaxed(its->ctlr_save, base + GITS_CTLR); >> > + >> > + if (GITS_TYPER_HWCOLLCNT(gic_read_typer(base + GITS_TYPER)) > 0) >> > + its_cpu_init_collection(its); >> >> This isn't correct. Think of a system where half the collections are in >> HW, and the other half memory based (nothing in the spec forbids this). >> You must evaluate the CID of each collection and replay the MAPC *only* >> if it falls into the range [0..HCC-1]. The memory-based collections are >> already mapped, and remapping an already mapped collection requires >> extra care (see MAPC and the UNPREDICTABLE behaviour when V=1), so don't >> go there. > > IIUC, this is only run on CPU0 (it's in syscore resume), so implicitly, > CID is 0. Thus, the current condition is already doing what you ask: > > HCC > 0 == CID > > which is equivalent to: > > HCC - 1 >= CID > > Or should we really double check what CPU we're running on? There seems to be the edge case where you hotplug CPU 0 before suspending. In that case, I believe you're on the lowest number CPU left? It seems that all of the CPUs that are disabled have the ITS reinitialized from scratch via enable_nonboot_cpus(). This code runs on only the CPU that firmware resumes with. If that CPU isn't CPU 0 for whatever reason, we need to make sure that it's processor ID is less than HCC. > > Brian