From: Rob Herring <robh@kernel.org>
To: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Andy Gross <andy.gross@linaro.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
linux-arm-msm <linux-arm-msm@vger.kernel.org>,
"moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE"
<linux-arm-kernel@lists.infradead.org>,
devicetree@vger.kernel.org
Subject: Re: [PATCH 1/2] arm64: dts: sdm845: Add minimal dts/dtsi files for sdm845 SoC and MTP
Date: Tue, 6 Feb 2018 14:31:08 -0600 [thread overview]
Message-ID: <CAL_JsqLb4PQ+NkA_RBAgB-5MzFKd+6wBvfCjXvoH-i8pGzzdTg@mail.gmail.com> (raw)
In-Reply-To: <20180125163216.29018-2-rnayak@codeaurora.org>
On Thu, Jan 25, 2018 at 10:32 AM, Rajendra Nayak <rnayak@codeaurora.org> wrote:
> Add a skeletal sdm845 SoC dtsi and MTP board dts/dtsi files
>
> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 13 ++
> arch/arm64/boot/dts/qcom/sdm845-mtp.dtsi | 11 ++
> arch/arm64/boot/dts/qcom/sdm845.dtsi | 308 +++++++++++++++++++++++++++++++
> 4 files changed, 333 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> create mode 100644 arch/arm64/boot/dts/qcom/sdm845-mtp.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/sdm845.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 55ec5ee7f7e8..c57701bed084 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -6,3 +6,4 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8992-bullhead-rev-101.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8994-angler-rev-101.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> new file mode 100644
> index 000000000000..95e41e42bee1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> @@ -0,0 +1,13 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + */
> +
> +/dts-v1/;
> +
> +#include "sdm845-mtp.dtsi"
> +
> +/ {
> + model = "Qualcomm Technologies, Inc. SDM845 MTP";
> + compatible = "qcom,sdm845-mtp";
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dtsi b/arch/arm64/boot/dts/qcom/sdm845-mtp.dtsi
> new file mode 100644
> index 000000000000..5b1022c20bad
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dtsi
> @@ -0,0 +1,11 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + */
> +
> +#include "sdm845.dtsi"
> +
> +/ {
> + soc {
> + };
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> new file mode 100644
> index 000000000000..a21f4912b3e2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -0,0 +1,308 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> + model = "Qualcomm Technologies, Inc. SDM845";
This should only be in the board level file.
> +
> + interrupt-parent = <&intc>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + chosen { };
> +
> + memory {
> + device_type = "memory";
> + /* We expect the bootloader to fill in the reg */
The start address is variable? If not you should populate the base and
have a unit-address.
> + reg = <0 0 0 0>;
> + };
> +
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + CPU0: cpu@0 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x0>;
> + enable-method = "psci";
> + next-level-cache = <&L2_0>;
> + L2_0: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + L3_0: l3-cache {
> + compatible = "cache";
> + };
> + };
> + };
> +
> + CPU1: cpu@100 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x100>;
> + enable-method = "psci";
> + next-level-cache = <&L2_100>;
> + L2_100: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + CPU2: cpu@200 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x200>;
> + enable-method = "psci";
> + next-level-cache = <&L2_200>;
> + L2_200: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + CPU3: cpu@300 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x300>;
> + enable-method = "psci";
> + next-level-cache = <&L2_300>;
> + L2_300: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + CPU4: cpu@400 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x400>;
> + enable-method = "psci";
> + next-level-cache = <&L2_400>;
> + L2_400: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + CPU5: cpu@500 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x500>;
> + enable-method = "psci";
> + next-level-cache = <&L2_500>;
> + L2_500: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + CPU6: cpu@600 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x600>;
> + enable-method = "psci";
> + next-level-cache = <&L2_600>;
> + L2_600: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + CPU7: cpu@700 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x700>;
> + enable-method = "psci";
> + next-level-cache = <&L2_700>;
> + L2_700: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> +
> + core1 {
> + cpu = <&CPU1>;
> + };
> +
> + core2 {
> + cpu = <&CPU2>;
> + };
> +
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&CPU4>;
> + };
> +
> + core1 {
> + cpu = <&CPU5>;
> + };
> +
> + core2 {
> + cpu = <&CPU6>;
> + };
> +
> + core3 {
> + cpu = <&CPU7>;
> + };
> + };
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + clocks {
> + xo_board: xo_board {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <19200000>;
> + clock-output-names = "xo_board";
> + };
> +
> + sleep_clk: sleep_clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32764>;
> + clock-output-names = "sleep_clk";
> + };
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> + };
> +
> + soc: soc {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0 0 0xffffffff>;
> + compatible = "simple-bus";
> +
> + intc: interrupt-controller@17a00000 {
> + compatible = "arm,gic-v3";
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + #redistributor-regions = <1>;
> + redistributor-stride = <0x0 0x20000>;
> + reg = <0x17a00000 0x10000>, /* GICD */
> + <0x17a60000 0x100000>; /* GICR * 8 */
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gcc: clock-controller@100000 {
> + compatible = "qcom,gcc-sdm845";
sdm845-gcc is the preferred order.
> + reg = <0x100000 0x1f0000>;
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + };
> +
> + tlmm: pinctrl@03400000 {
> + compatible = "qcom,sdm845-pinctrl";
> + reg = <0x03400000 0xc00000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_NONE>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + timer@17C90000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + compatible = "arm,armv7-timer-mem";
> + reg = <0x17C90000 0x1000>;
> + clock-frequency = <19200000>;
> +
> + frame@17CA0000 {
> + frame-number = <0>;
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x17CA0000 0x1000>,
> + <0x17CB0000 0x1000>;
> + };
> +
> + frame@17cc0000 {
> + frame-number = <1>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x17cc0000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@17cd0000 {
> + frame-number = <2>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x17cd0000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@17ce0000 {
> + frame-number = <3>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x17ce0000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@17cf0000 {
> + frame-number = <4>;
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x17cf0000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@17d00000 {
> + frame-number = <5>;
> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x17d00000 0x1000>;
> + status = "disabled";
> + };
> +
> + frame@17d10000 {
> + frame-number = <6>;
> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x17d10000 0x1000>;
> + status = "disabled";
> + };
> + };
> +
> + spmi_bus: qcom,spmi@c440000 {
spmi@...
> + compatible = "qcom,spmi-pmic-arb";
> + reg = <0xc440000 0x1100>,
> + <0xc600000 0x2000000>,
> + <0xe600000 0x100000>,
> + <0xe700000 0xa0000>,
> + <0xc40a000 0x26000>;
> + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> + interrupt-names = "periph_irq";
> + interrupts = <GIC_SPI 481 IRQ_TYPE_NONE>;
> + qcom,ee = <0>;
> + qcom,channel = <0>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + interrupt-controller;
> + #interrupt-cells = <4>;
> + cell-index = <0>;
> + };
> +
> + };
> +};
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2018-02-06 20:31 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-25 16:32 [PATCH 0/2] Add DTS for SDM845 SoC and MTP Rajendra Nayak
[not found] ` <20180125163216.29018-1-rnayak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-01-25 16:32 ` [PATCH 1/2] arm64: dts: sdm845: Add minimal dts/dtsi files for sdm845 " Rajendra Nayak
[not found] ` <20180125163216.29018-2-rnayak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-01-26 20:31 ` Evan Green
2018-01-30 8:48 ` Rajendra Nayak
2018-01-26 22:15 ` Stephen Boyd
[not found] ` <20180126221501.GD28313-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-01-29 8:13 ` Rajendra Nayak
2018-01-30 9:48 ` Stephen Boyd
2018-01-30 10:25 ` Rajendra Nayak
2018-02-06 20:26 ` Rob Herring
[not found] ` <CAL_JsqJ1xjQ5ZP-KXeZQ0s=ib8GTfvfYjFqyy+Zcub-akCs7Bw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2018-02-07 4:14 ` Rajendra Nayak
2018-02-06 18:54 ` Bjorn Andersson
2018-02-07 4:15 ` Rajendra Nayak
2018-02-06 20:31 ` Rob Herring [this message]
2018-02-07 4:47 ` Rajendra Nayak
2018-02-07 17:37 ` Rob Herring
2018-01-25 16:32 ` [PATCH 2/2] arm64: dts: sdm845: Add serial console support Rajendra Nayak
2018-01-26 22:18 ` Stephen Boyd
2018-01-29 8:18 ` Rajendra Nayak
2018-02-06 19:00 ` Bjorn Andersson
2018-02-06 18:37 ` Doug Anderson
[not found] ` <CAD=FV=WcCnQJc25=sKWtOi=ZWi=ium6DVsexuQnsLDL=aJE6-Q-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2018-02-06 19:06 ` Bjorn Andersson
2018-02-06 19:49 ` Doug Anderson
[not found] ` <CAD=FV=Whxf1VRJ6qx9mioEEkTeS+uJfJKPbOMcGy-Wigh_NORw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2018-02-06 20:05 ` Bjorn Andersson
2018-02-07 4:12 ` Rajendra Nayak
[not found] ` <20180126221808.GE28313-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-02-06 20:36 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAL_JsqLb4PQ+NkA_RBAgB-5MzFKd+6wBvfCjXvoH-i8pGzzdTg@mail.gmail.com \
--to=robh@kernel.org \
--cc=andy.gross@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=rnayak@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).