From: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Sibi Sankar <sibis@codeaurora.org>,
Jeffrey Hugo <jhugo@codeaurora.org>,
Rob Herring <robh+dt@kernel.org>,
Ohad Ben-Cohen <ohad@wizery.com>,
Mark Rutland <mark.rutland@arm.com>,
MSM <linux-arm-msm@vger.kernel.org>,
linux-remoteproc@vger.kernel.org,
DTML <devicetree@vger.kernel.org>,
lkml <linux-kernel@vger.kernel.org>,
Andy Gross <agross@kernel.org>
Subject: Re: [PATCH v2 5/5] arm64: dts: qcom: msm8998: Add ADSP, MPSS and SLPI nodes
Date: Fri, 20 Dec 2019 07:33:11 -0700 [thread overview]
Message-ID: <CAOCk7NoaWw8Tor-P02SESztWEGpGMK6GbRNG45yMVYhMdDCEnQ@mail.gmail.com> (raw)
In-Reply-To: <20191220065954.GA1908628@ripper>
On Fri, Dec 20, 2019 at 12:00 AM Bjorn Andersson
<bjorn.andersson@linaro.org> wrote:
>
> On Wed 18 Dec 05:22 PST 2019, Sibi Sankar wrote:
>
> > This patch adds ADSP, MPSS and SLPI nodes for MSM8998 SoCs.
> >
> > Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
> > ---
> > arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi | 8 ++
> > arch/arm64/boot/dts/qcom/msm8998.dtsi | 124 ++++++++++++++++++++++
> > 2 files changed, 132 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
> > index 6db3f9e0344d1..e87094665c52c 100644
> > --- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
> > @@ -312,6 +312,14 @@
> > };
> > };
> >
> > +&remoteproc_adsp {
> > + status = "okay";
> > +};
> > +
> > +&remoteproc_slpi {
> > + status = "okay";
> > +};
> > +
> > &tlmm {
> > gpio-reserved-ranges = <0 4>, <81 4>;
> > };
> > diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
> > index 8d799e868a5d3..014127700afb0 100644
> > --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
> > @@ -1075,6 +1075,61 @@
> > #interrupt-cells = <0x2>;
> > };
> >
> > + remoteproc_mss: remoteproc@4080000 {
> > + compatible = "qcom,msm8998-mss-pil";
> > + reg = <0x04080000 0x100>, <0x04180000 0x20>;
> > + reg-names = "qdsp6", "rmb";
> > +
> > + interrupts-extended =
> > + <&intc GIC_SPI 448 IRQ_TYPE_EDGE_RISING>,
> > + <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> > + <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> > + <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> > + <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
> > + <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
> > + interrupt-names = "wdog", "fatal", "ready",
> > + "handover", "stop-ack",
> > + "shutdown-ack";
> > +
> > + clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
> > + <&gcc GCC_BIMC_MSS_Q6_AXI_CLK>,
> > + <&gcc GCC_BOOT_ROM_AHB_CLK>,
> > + <&gcc GCC_MSS_GPLL0_DIV_CLK_SRC>,
> > + <&gcc GCC_MSS_SNOC_AXI_CLK>,
> > + <&gcc GCC_MSS_MNOC_BIMC_AXI_CLK>,
> > + <&rpmcc RPM_SMD_QDSS_CLK>,
> > + <&rpmcc RPM_SMD_XO_CLK_SRC>;
>
> RPM_SMD_XO_CLK_SRC doesn't seem to be implemented...
>
> I did pull in a patch from Jeff that defines it, but when I boot the
> modem I see the following error repeatedly:
Yeah, we need to figure out a solution for rpmcc to actually provide
this since the previous N solutions were not acceptable. Its on my
todo list to look into in Jan. However, I really think the DT should
be defined this way, since it replicates the hardware config.
>
> [ 616.632227] qcom-q6v5-mss 4080000.remoteproc: fatal error received: dog_hb.c:266:DOG_HB detects starvation of task 0xda172640, triage with its own
Maybe the BIMC fix will address this?
>
>
>
> All the qrtr services seems registered nicely, so the remote does come
> up before it goes down.
>
> Also, adsp comes up nicely.
>
> Regards,
> Bjorn
>
> > + clock-names = "iface", "bus", "mem", "gpll0_mss",
> > + "snoc_axi", "mnoc_axi", "qdss", "xo";
> > +
> > + qcom,smem-states = <&modem_smp2p_out 0>;
> > + qcom,smem-state-names = "stop";
> > +
> > + resets = <&gcc GCC_MSS_RESTART>;
> > + reset-names = "mss_restart";
> > +
> > + qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
> > +
> > + power-domains = <&rpmpd MSM8998_VDDCX>,
> > + <&rpmpd MSM8998_VDDMX>;
> > + power-domain-names = "cx", "mx";
> > +
> > + mba {
> > + memory-region = <&mba_mem>;
> > + };
> > +
> > + mpss {
> > + memory-region = <&mpss_mem>;
> > + };
> > +
> > + glink-edge {
> > + interrupts = <GIC_SPI 452 IRQ_TYPE_EDGE_RISING>;
> > + label = "modem";
> > + qcom,remote-pid = <1>;
> > + mboxes = <&apcs_glb 15>;
> > + };
> > + };
> > +
> > gpucc: clock-controller@5065000 {
> > compatible = "qcom,msm8998-gpucc";
> > #clock-cells = <1>;
> > @@ -1088,6 +1143,42 @@
> > "gpll0";
> > };
> >
> > + remoteproc_slpi: remoteproc@5800000 {
> > + compatible = "qcom,msm8998-slpi-pas";
> > + reg = <0x05800000 0x4040>;
> > +
> > + interrupts-extended = <&intc GIC_SPI 390 IRQ_TYPE_EDGE_RISING>,
> > + <&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> > + <&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> > + <&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> > + <&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> > + interrupt-names = "wdog", "fatal", "ready",
> > + "handover", "stop-ack";
> > +
> > + px-supply = <&vreg_lvs2a_1p8>;
> > +
> > + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
> > + <&rpmcc RPM_SMD_AGGR2_NOC_CLK>;
> > + clock-names = "xo", "aggre2";
> > +
> > + memory-region = <&slpi_mem>;
> > +
> > + qcom,smem-states = <&slpi_smp2p_out 0>;
> > + qcom,smem-state-names = "stop";
> > +
> > + power-domains = <&rpmpd MSM8998_SSCCX>;
> > + power-domain-names = "ssc_cx";
> > +
> > + status = "disabled";
> > +
> > + glink-edge {
> > + interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
> > + label = "dsps";
> > + qcom,remote-pid = <3>;
> > + mboxes = <&apcs_glb 27>;
> > + };
> > + };
> > +
> > stm: stm@6002000 {
> > compatible = "arm,coresight-stm", "arm,primecell";
> > reg = <0x06002000 0x1000>,
> > @@ -1880,6 +1971,39 @@
> > #size-cells = <0>;
> > };
> >
> > + remoteproc_adsp: remoteproc@17300000 {
> > + compatible = "qcom,msm8998-adsp-pas";
> > + reg = <0x17300000 0x4040>;
> > +
> > + interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
> > + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> > + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> > + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> > + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> > + interrupt-names = "wdog", "fatal", "ready",
> > + "handover", "stop-ack";
> > +
> > + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
> > + clock-names = "xo";
> > +
> > + memory-region = <&adsp_mem>;
> > +
> > + qcom,smem-states = <&adsp_smp2p_out 0>;
> > + qcom,smem-state-names = "stop";
> > +
> > + power-domains = <&rpmpd MSM8998_VDDCX>;
> > + power-domain-names = "cx";
> > +
> > + status = "disabled";
> > +
> > + glink-edge {
> > + interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
> > + label = "lpass";
> > + qcom,remote-pid = <2>;
> > + mboxes = <&apcs_glb 9>;
> > + };
> > + };
> > +
> > apcs_glb: mailbox@17911000 {
> > compatible = "qcom,msm8998-apcs-hmss-global";
> > reg = <0x17911000 0x1000>;
> > --
> > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> > a Linux Foundation Collaborative Project
next prev parent reply other threads:[~2019-12-20 14:33 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-18 13:22 [PATCH v2 0/5] Add the missing remoteprocs on MSM8998 Sibi Sankar
2019-12-18 13:22 ` [PATCH v2 1/5] remoteproc: q6v5-mss: Remove mem clk from the active pool Sibi Sankar
2019-12-18 13:22 ` [PATCH v2 2/5] dt-bindings: remoteproc: qcom: Add ADSP and SLPI support for MSM8998 SoC Sibi Sankar
2019-12-18 13:22 ` [PATCH v2 3/5] remoteproc: qcom: pas: Add MSM8998 ADSP and SLPI support Sibi Sankar
2019-12-18 13:22 ` [PATCH v2 4/5] arm64: dts: qcom: msm8998: Update reserved memory map Sibi Sankar
2019-12-18 13:22 ` [PATCH v2 5/5] arm64: dts: qcom: msm8998: Add ADSP, MPSS and SLPI nodes Sibi Sankar
2019-12-20 6:59 ` Bjorn Andersson
2019-12-20 14:33 ` Jeffrey Hugo [this message]
2019-12-20 17:05 ` Bjorn Andersson
2019-12-20 17:10 ` Jeffrey Hugo
2019-12-20 18:02 ` Bjorn Andersson
2019-12-20 18:04 ` Jeffrey Hugo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAOCk7NoaWw8Tor-P02SESztWEGpGMK6GbRNG45yMVYhMdDCEnQ@mail.gmail.com \
--to=jeffrey.l.hugo@gmail.com \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jhugo@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=ohad@wizery.com \
--cc=robh+dt@kernel.org \
--cc=sibis@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).