From: Rob Herring <robh@kernel.org>
To: Mathew McBride <matt@traverse.com.au>
Cc: Shawn Guo <shawnguo@kernel.org>, Li Yang <leoyang.li@nxp.com>,
Ioana Ciornei <ioana.ciornei@nxp.com>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org
Subject: Re: [PATCH v2 5/5] arm64: dts: add device tree for Traverse Ten64 (LS1088A)
Date: Thu, 29 Jul 2021 16:45:25 -0600 [thread overview]
Message-ID: <YQMvhc374A4g6FWY@robh.at.kernel.org> (raw)
In-Reply-To: <20210726071216.22711-6-matt@traverse.com.au>
On Mon, Jul 26, 2021 at 07:12:16AM +0000, Mathew McBride wrote:
> The Traverse Technologies Ten64 is a Mini-ITX form factor
> networking board using the NXP LS1088A SoC.
>
> This device tree only describes features which the mainline
> kernel currently has support for, such as some I2C-connected
> devices that are not described at present.
>
> System documentation may be found at ten64doc.traverse.com.au
>
> Signed-off-by: Mathew McBride <matt@traverse.com.au>
> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> # for the MAC/PHY
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../boot/dts/freescale/fsl-ls1088a-ten64.dts | 377 ++++++++++++++++++
> 2 files changed, 378 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 25806c4924cb..2b3ee42e4a2a 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-ten64.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
> new file mode 100644
> index 000000000000..59fa344a8854
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
> @@ -0,0 +1,377 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for Travese Ten64 (LS1088) board
> + * Based on fsl-ls1088a-rdb.dts
> + * Copyright 2017-2020 NXP
> + * Copyright 2019-2021 Traverse Technologies
> + *
> + * Author: Mathew McBride <matt@traverse.com.au>
> + */
> +
> +/dts-v1/;
> +
> +#include "fsl-ls1088a.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Traverse Ten64";
> + compatible = "traverse,ten64", "fsl,ls1088a";
> +
> + aliases {
> + serial0 = &duart0;
> + serial1 = &duart1;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + buttons {
> + compatible = "gpio-keys";
> +
> + /* Fired by system controller when
> + * external power off (e.g ATX Power Button)
> + * asserted
> + */
> + powerdn {
> + label = "External Power Down";
> + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
> + interrupts = <&gpio1 17 IRQ_TYPE_EDGE_FALLING>;
> + linux,code = <KEY_POWER>;
> + };
> +
> + /* Rear Panel 'ADMIN' button (GPIO_H) */
> + admin {
> + label = "ADMIN button";
> + gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
> + interrupts = <&gpio3 8 IRQ_TYPE_EDGE_RISING>;
> + linux,code = <KEY_WPS_BUTTON>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + sfp1down {
> + label = "ten64:green:sfp1:down";
> + gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>;
> + };
> +
> + sfp2up {
> + label = "ten64:green:sfp2:up";
> + gpios = <&gpio3 12 GPIO_ACTIVE_HIGH>;
> + };
> +
> + admin {
> + label = "ten64:admin";
> + gpios = <&sfpgpio 12 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + sfp_xg0: dpmac2-sfp {
> + compatible = "sff,sfp";
> + i2c-bus = <&sfplower_i2c>;
> + tx-fault-gpios = <&sfpgpio 0 GPIO_ACTIVE_HIGH>;
> + tx-disable-gpios = <&sfpgpio 1 GPIO_ACTIVE_HIGH>;
> + mod-def0-gpios = <&sfpgpio 2 GPIO_ACTIVE_LOW>;
> + los-gpios = <&sfpgpio 3 GPIO_ACTIVE_HIGH>;
> + maximum-power-milliwatt = <2000>;
> + };
> +
> + sfp_xg1: dpmac1-sfp {
> + compatible = "sff,sfp";
> + i2c-bus = <&sfpupper_i2c>;
> + tx-fault-gpios = <&sfpgpio 4 GPIO_ACTIVE_HIGH>;
> + tx-disable-gpios = <&sfpgpio 5 GPIO_ACTIVE_HIGH>;
> + mod-def0-gpios = <&sfpgpio 6 GPIO_ACTIVE_LOW>;
> + los-gpios = <&sfpgpio 7 GPIO_ACTIVE_HIGH>;
> + maximum-power-milliwatt = <2000>;
> + };
> +};
> +
> +/* XG1 - Upper SFP */
> +&dpmac1 {
> + sfp = <&sfp_xg1>;
> + pcs-handle = <&pcs1>;
> + phy-connection-type = "10gbase-r";
> + managed = "in-band-status";
> +};
> +
> +/* XG0 - Lower SFP */
> +&dpmac2 {
> + sfp = <&sfp_xg0>;
> + pcs-handle = <&pcs2>;
> + phy-connection-type = "10gbase-r";
> + managed = "in-band-status";
> +};
> +
> +/* DPMAC3..6 is GE4 to GE8 */
> +&dpmac3 {
> + phy-handle = <&mdio1_phy5>;
> + phy-connection-type = "qsgmii";
> + managed = "in-band-status";
> + pcs-handle = <&pcs3_0>;
> +};
> +
> +&dpmac4 {
> + phy-handle = <&mdio1_phy6>;
> + phy-connection-type = "qsgmii";
> + managed = "in-band-status";
> + pcs-handle = <&pcs3_1>;
> +};
> +
> +&dpmac5 {
> + phy-handle = <&mdio1_phy7>;
> + phy-connection-type = "qsgmii";
> + managed = "in-band-status";
> + pcs-handle = <&pcs3_2>;
> +};
> +
> +&dpmac6 {
> + phy-handle = <&mdio1_phy8>;
> + phy-connection-type = "qsgmii";
> + managed = "in-band-status";
> + pcs-handle = <&pcs3_3>;
> +};
> +
> +/* DPMAC7..10 is GE0 to GE3 */
> +&dpmac7 {
> + phy-handle = <&mdio1_phy1>;
> + phy-connection-type = "qsgmii";
> + managed = "in-band-status";
> + pcs-handle = <&pcs7_0>;
> +};
> +
> +&dpmac8 {
> + phy-handle = <&mdio1_phy2>;
> + phy-connection-type = "qsgmii";
> + managed = "in-band-status";
> + pcs-handle = <&pcs7_1>;
> +};
> +
> +&dpmac9 {
> + phy-handle = <&mdio1_phy3>;
> + phy-connection-type = "qsgmii";
> + managed = "in-band-status";
> + pcs-handle = <&pcs7_2>;
> +};
> +
> +&dpmac10 {
> + phy-handle = <&mdio1_phy4>;
> + phy-connection-type = "qsgmii";
> + managed = "in-band-status";
> + pcs-handle = <&pcs7_3>;
> +};
> +
> +&duart0 {
> + status = "okay";
> +};
> +
> +&duart1 {
> + status = "okay";
> +};
> +
> +&emdio1 {
> + status = "okay";
> +
> + mdio1_phy5: ethernet-phy@c {
> + reg = <0xc>;
> + };
> +
> + mdio1_phy6: ethernet-phy@d {
> + reg = <0xd>;
> + };
> +
> + mdio1_phy7: ethernet-phy@e {
> + reg = <0xe>;
> + };
> +
> + mdio1_phy8: ethernet-phy@f {
> + reg = <0xf>;
> + };
> +
> + mdio1_phy1: ethernet-phy@1c {
> + reg = <0x1c>;
> + };
> +
> + mdio1_phy2: ethernet-phy@1d {
> + reg = <0x1d>;
> + };
> +
> + mdio1_phy3: ethernet-phy@1e {
> + reg = <0x1e>;
> + };
> +
> + mdio1_phy4: ethernet-phy@1f {
> + reg = <0x1f>;
> + };
> +};
> +
> +&esdhc {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + sfpgpio: gpio@76 {
> + compatible = "ti,tca9539";
> + reg = <0x76>;
> + #gpio-cells = <2>;
> + gpio-controller;
> +
> + admin_led_lower {
> + gpio-hog;
> + gpios = <13 GPIO_ACTIVE_HIGH>;
> + output-low;
> + };
> + };
> +
> + at97sc: tpm@29 {
> + compatible = "atmel,at97sc3204t";
> + reg = <0x29>;
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + rx8035: rtc@32 {
> + compatible = "epson,rx8035";
> + reg = <0x32>;
> + };
> +};
> +
> +&i2c3 {
> + status = "okay";
> +
> + i2c-switch@70 {
> + compatible = "nxp,pca9540";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x70>;
> +
> + sfpupper_i2c: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + sfplower_i2c: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> + };
> +};
> +
> +&pcs_mdio1 {
> + status = "okay";
> +};
> +
> +&pcs_mdio2 {
> + status = "okay";
> +};
> +
> +&pcs_mdio3 {
> + status = "okay";
> +};
> +
> +&pcs_mdio7 {
> + status = "okay";
> +};
> +
> +&qspi {
> + status = "okay";
> +
> + en25s64: flash@0 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> +
> + partition@0 {
New users should put all the partitions under a 'partitions' node.
> + label = "bl2";
> + reg = <0 0x100000>;
> + };
> +
> + partition@100000 {
> + label = "bl3";
> + reg = <0x100000 0x200000>;
> + };
> +
> + partition@300000 {
> + label = "mcfirmware";
> + reg = <0x300000 0x200000>;
> + };
> +
> + partition@500000 {
> + label = "ubootenv";
> + reg = <0x500000 0x80000>;
> + };
> +
> + partition@580000 {
> + label = "dpl";
> + reg = <0x580000 0x40000>;
> + };
> +
> + partition@5C0000 {
> + label = "dpc";
> + reg = <0x5C0000 0x40000>;
> + };
> +
> + partition@600000 {
> + label = "devicetree";
> + reg = <0x600000 0x40000>;
> + };
> + };
> +
> + nand: flash@1 {
> + compatible = "spi-nand";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <1>;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> +
> + /* reserved for future boot direct from NAND flash
> + * (this would use the same layout as the 8MiB NOR flash)
> + */
> + partition@0 {
> + label = "nand-boot-reserved";
> + reg = <0 0x800000>;
> + };
> +
> + /* recovery / install environment */
> + partition@800000 {
> + label = "recovery";
> + reg = <0x800000 0x2000000>;
> + };
> +
> + /* ubia (first OpenWrt) - a/b names to prevent confusion with ubi0/1/etc. */
> + partition@2800000 {
> + label = "ubia";
> + reg = <0x2800000 0x6C00000>;
> + };
> +
> + /* ubib (second OpenWrt) */
> + partition@9400000 {
> + label = "ubib";
> + reg = <0x9400000 0x6C00000>;
> + };
> + };
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb1 {
> + status = "okay";
> +};
> --
> 2.30.1
>
>
next prev parent reply other threads:[~2021-07-29 22:45 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-22 4:24 [PATCH 0/5] Add Traverse Technologies Ten64 board DTS Mathew McBride
2021-07-22 4:24 ` [PATCH 1/5] arm64: dts: ls1088a: add internal PCS for DPMAC1 node Mathew McBride
2021-07-22 7:48 ` Ioana Ciornei
2021-07-22 4:24 ` [PATCH 2/5] arm64: dts: ls1088a: add missing PMU node Mathew McBride
2021-07-23 8:36 ` Shawn Guo
2021-07-22 4:24 ` [PATCH 3/5] dt-bindings: vendor-prefixes: add Traverse Technologies Mathew McBride
2021-07-22 4:24 ` [PATCH 4/5] dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board Mathew McBride
2021-07-22 4:24 ` [PATCH 5/5] arm64: dts: add device tree for Traverse Ten64 (LS1088A) Mathew McBride
2021-07-22 8:44 ` Ioana Ciornei
2021-07-23 9:46 ` Shawn Guo
2021-07-26 7:12 ` [PATCH v2 0/5] Add Traverse Technologies Ten64 board DTS Mathew McBride
2021-07-26 7:12 ` [PATCH v2 1/5] arm64: dts: ls1088a: add internal PCS for DPMAC1 node Mathew McBride
2021-07-26 7:12 ` [PATCH v2 2/5] arm64: dts: ls1088a: add missing PMU node Mathew McBride
2021-07-26 7:12 ` [PATCH v2 3/5] dt-bindings: vendor-prefixes: add Traverse Technologies Mathew McBride
2021-07-29 22:41 ` Rob Herring
2021-07-26 7:12 ` [PATCH v2 4/5] dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board Mathew McBride
2021-07-29 22:45 ` Rob Herring
2021-07-26 7:12 ` [PATCH v2 5/5] arm64: dts: add device tree for Traverse Ten64 (LS1088A) Mathew McBride
2021-07-29 22:45 ` Rob Herring [this message]
2021-08-10 5:38 ` [PATCH v3 0/5] Add Traverse Technologies Ten64 board DTS Mathew McBride
2021-08-10 5:38 ` [PATCH v3 1/5] arm64: dts: ls1088a: add internal PCS for DPMAC1 node Mathew McBride
2021-08-10 5:38 ` [PATCH v3 2/5] arm64: dts: ls1088a: add missing PMU node Mathew McBride
2021-08-10 5:38 ` [PATCH v3 3/5] dt-bindings: vendor-prefixes: add Traverse Technologies Mathew McBride
2021-08-10 5:38 ` [PATCH v3 4/5] dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board Mathew McBride
2021-08-10 5:38 ` [PATCH v3 5/5] arm64: dts: add device tree for Traverse Ten64 (LS1088A) Mathew McBride
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YQMvhc374A4g6FWY@robh.at.kernel.org \
--to=robh@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=ioana.ciornei@nxp.com \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=matt@traverse.com.au \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).