* [PATCH] arm64: dts: rockchip: add ROCK Pi S DTS support
@ 2019-12-15 17:33 Akash Gajjar
2019-12-15 17:50 ` akash
2019-12-16 2:47 ` Andy Yan
0 siblings, 2 replies; 5+ messages in thread
From: Akash Gajjar @ 2019-12-15 17:33 UTC (permalink / raw)
To: heiko
Cc: jagan, Akash Gajjar, Rob Herring, Mark Rutland, Douglas Anderson,
Robin Murphy, Andy Yan, Nick Xie, Matthias Kaehlcke, Kever Yang,
Markus Reichl, Tomeu Vizoso, Vivek Unune, devicetree,
linux-arm-kernel, linux-rockchip, linux-kernel
ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
- 256MB/512MB DDR3 RAM
- SD, NAND flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
- USB2.0 Type-A HOST x1
- USB3.0 Type-C OTG x1
- 26-pin expansion header
- USB Type-C DC 5V Power Supply
This patch enables
- Console
- NAND Flash
- SD Card
Signed-off-by: Akash Gajjar <akash@openedev.com>
---
.../devicetree/bindings/arm/rockchip.yaml | 5 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3308-rock-pi-S.dts | 221 ++++++++++++++++++
3 files changed, 227 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index d9847b306b83..48d40c928d45 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -422,6 +422,11 @@ properties:
- const: radxa,rockpi4
- const: rockchip,rk3399
+ - description: Radxa ROCK Pi S
+ items:
+ - const: radxa,rockpis
+ - const: rockchip,rk3308
+
- description: Radxa Rock2 Square
items:
- const: radxa,rock2-square
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 48fb631d5451..cc9e8c824980 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -2,6 +2,7 @@
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-rock-pi-S.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts
new file mode 100644
index 000000000000..e5fae451c631
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Akash Gajjar <akash@openedev.com>
+ * Copyright (c) 2019 Jagan Teki <jagan@openedev.com>
+ */
+
+/dts-v1/;
+#include "rk3308.dtsi"
+
+/ {
+ model = "Radxa ROCK Pi S";
+ compatible = "radxa,rockpis", "rockchip,rk3308";
+
+ chosen {
+ stdout-path = "serial0:1500000n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&green_led_gio>, <&heartbeat_led_gpio>;
+
+ green-led {
+ label = "rockpis:green:power";
+ gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ default-state = "on";
+ };
+
+ blue-led {
+ label = "rockpis:blue:user";
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ reset-gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vdd_core: vdd-core {
+ compatible = "pwm-regulator";
+ pwms = <&pwm0 0 5000 1>;
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <827000>;
+ regulator-max-microvolt = <1340000>;
+ regulator-init-microvolt = <1015000>;
+ regulator-settling-time-up-us = <250>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vdd_log: vdd-log {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc_ddr: vcc-ddr {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc_1v8: vcc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_io: vcc-io {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_io";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_otg: vcc5v0-otg {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_otg";
+ regulator-always-on;
+ gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_core>;
+};
+
+&emmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ supports-sd;
+ disable-wp;
+ non-removable;
+ num-slots = <1>;
+ vin-supply = <&vcc_io>;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ max-frequeency = <150000000>;
+ supports-sd;
+ disable-wp;
+ num-slots = <1>;
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_det &sdmmc_bus4>;
+ card-detect-delay = <800>;
+ status = "okay";
+};
+
+&spi2 {
+ status = "okay";
+ max-freq = <10000000>;
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtc_32k>;
+
+ leds {
+ green_led_gio: green-led-gpio {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ heartbeat_led_gpio: heartbeat-led-gpio {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wifi_host_wake: wifi-host-wake {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+ pinctrl-0 = <&pwm0_pin_pull_down>;
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ max-frequency = <1000000>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ supports-sdio;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_xfer &uart4_rts &uart4_cts>;
+ status = "okay";
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: add ROCK Pi S DTS support
2019-12-15 17:33 [PATCH] arm64: dts: rockchip: add ROCK Pi S DTS support Akash Gajjar
@ 2019-12-15 17:50 ` akash
2019-12-16 2:47 ` Andy Yan
1 sibling, 0 replies; 5+ messages in thread
From: akash @ 2019-12-15 17:50 UTC (permalink / raw)
To: heiko
Cc: jagan, Rob Herring, Mark Rutland, Douglas Anderson, Robin Murphy,
Andy Yan, Nick Xie, Matthias Kaehlcke, Kever Yang, Markus Reichl,
Tomeu Vizoso, Vivek Unune, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel
Rock Pi S Linux 5.5.0-rc1 Boot Logs available on
https://paste.ubuntu.com/p/2K9NpWJYpb/
On 15/12/19 11:03 pm, Akash Gajjar wrote:
> ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
> - 256MB/512MB DDR3 RAM
> - SD, NAND flash (optional on board 1/2/4/8Gb)
> - 100MB ethernet, PoE (optional)
> - Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
> - USB2.0 Type-A HOST x1
> - USB3.0 Type-C OTG x1
> - 26-pin expansion header
> - USB Type-C DC 5V Power Supply
>
> This patch enables
> - Console
> - NAND Flash
> - SD Card
>
> Signed-off-by: Akash Gajjar <akash@openedev.com>
> ---
> .../devicetree/bindings/arm/rockchip.yaml | 5 +
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3308-rock-pi-S.dts | 221 ++++++++++++++++++
> 3 files changed, 227 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
> index d9847b306b83..48d40c928d45 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.yaml
> +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
> @@ -422,6 +422,11 @@ properties:
> - const: radxa,rockpi4
> - const: rockchip,rk3399
>
> + - description: Radxa ROCK Pi S
> + items:
> + - const: radxa,rockpis
> + - const: rockchip,rk3308
> +
> - description: Radxa Rock2 Square
> items:
> - const: radxa,rock2-square
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 48fb631d5451..cc9e8c824980 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -2,6 +2,7 @@
> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-rock-pi-S.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts
> new file mode 100644
> index 000000000000..e5fae451c631
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts
> @@ -0,0 +1,221 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Akash Gajjar <akash@openedev.com>
> + * Copyright (c) 2019 Jagan Teki <jagan@openedev.com>
> + */
> +
> +/dts-v1/;
> +#include "rk3308.dtsi"
> +
> +/ {
> + model = "Radxa ROCK Pi S";
> + compatible = "radxa,rockpis", "rockchip,rk3308";
> +
> + chosen {
> + stdout-path = "serial0:1500000n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&green_led_gio>, <&heartbeat_led_gpio>;
> +
> + green-led {
> + label = "rockpis:green:power";
> + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + default-state = "on";
> + };
> +
> + blue-led {
> + label = "rockpis:blue:user";
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_h>;
> + reset-gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
> + };
> +
> + vcc5v0_sys: vcc5v0-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + vdd_core: vdd-core {
> + compatible = "pwm-regulator";
> + pwms = <&pwm0 0 5000 1>;
> + regulator-name = "vdd_core";
> + regulator-min-microvolt = <827000>;
> + regulator-max-microvolt = <1340000>;
> + regulator-init-microvolt = <1015000>;
> + regulator-settling-time-up-us = <250>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vdd_log: vdd-log {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_log";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1050000>;
> + regulator-max-microvolt = <1050000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc_ddr: vcc-ddr {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc_1v8: vcc-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_1v8";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_io: vcc-io {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_io";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc5v0_otg: vcc5v0-otg {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_otg";
> + regulator-always-on;
> + gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + pinctrl-names = "default";
> + pinctrl-0 = <&otg_vbus_drv>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_core>;
> +};
> +
> +&emmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + supports-sd;
> + disable-wp;
> + non-removable;
> + num-slots = <1>;
> + vin-supply = <&vcc_io>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + max-frequeency = <150000000>;
> + supports-sd;
> + disable-wp;
> + num-slots = <1>;
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_det &sdmmc_bus4>;
> + card-detect-delay = <800>;
> + status = "okay";
> +};
> +
> +&spi2 {
> + status = "okay";
> + max-freq = <10000000>;
> +};
> +
> +&pinctrl {
> + pinctrl-names = "default";
> + pinctrl-0 = <&rtc_32k>;
> +
> + leds {
> + green_led_gio: green-led-gpio {
> + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + heartbeat_led_gpio: heartbeat-led-gpio {
> + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + otg_vbus_drv: otg-vbus-drv {
> + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + wifi_host_wake: wifi-host-wake {
> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +};
> +
> +&pwm0 {
> + status = "okay";
> + pinctrl-0 = <&pwm0_pin_pull_down>;
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + bus-width = <4>;
> + max-frequency = <1000000>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + supports-sdio;
> + keep-power-in-suspend;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + sd-uhs-sdr104;
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_xfer &uart4_rts &uart4_cts>;
> + status = "okay";
> +};
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: add ROCK Pi S DTS support
2019-12-15 17:33 [PATCH] arm64: dts: rockchip: add ROCK Pi S DTS support Akash Gajjar
2019-12-15 17:50 ` akash
@ 2019-12-16 2:47 ` Andy Yan
1 sibling, 0 replies; 5+ messages in thread
From: Andy Yan @ 2019-12-16 2:47 UTC (permalink / raw)
To: Akash Gajjar, heiko
Cc: jagan, Rob Herring, Mark Rutland, Douglas Anderson, Robin Murphy,
Nick Xie, Matthias Kaehlcke, Kever Yang, Markus Reichl,
Tomeu Vizoso, Vivek Unune, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel
Hi Akash:
On 12/16/19 1:33 AM, Akash Gajjar wrote:
> ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
> - 256MB/512MB DDR3 RAM
> - SD, NAND flash (optional on board 1/2/4/8Gb)
> - 100MB ethernet, PoE (optional)
> - Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
> - USB2.0 Type-A HOST x1
> - USB3.0 Type-C OTG x1
> - 26-pin expansion header
> - USB Type-C DC 5V Power Supply
>
> This patch enables
> - Console
> - NAND Flash
> - SD Card
>
> Signed-off-by: Akash Gajjar <akash@openedev.com>
> ---
> .../devicetree/bindings/arm/rockchip.yaml | 5 +
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3308-rock-pi-S.dts | 221 ++++++++++++++++++
> 3 files changed, 227 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
> index d9847b306b83..48d40c928d45 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.yaml
> +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
> @@ -422,6 +422,11 @@ properties:
> - const: radxa,rockpi4
> - const: rockchip,rk3399
>
> + - description: Radxa ROCK Pi S
> + items:
> + - const: radxa,rockpis
> + - const: rockchip,rk3308
> +
> - description: Radxa Rock2 Square
> items:
> - const: radxa,rock2-square
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 48fb631d5451..cc9e8c824980 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -2,6 +2,7 @@
> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-rock-pi-S.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts
> new file mode 100644
> index 000000000000..e5fae451c631
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-S.dts
> @@ -0,0 +1,221 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Akash Gajjar <akash@openedev.com>
> + * Copyright (c) 2019 Jagan Teki <jagan@openedev.com>
> + */
> +
> +/dts-v1/;
> +#include "rk3308.dtsi"
> +
> +/ {
> + model = "Radxa ROCK Pi S";
> + compatible = "radxa,rockpis", "rockchip,rk3308";
> +
> + chosen {
> + stdout-path = "serial0:1500000n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&green_led_gio>, <&heartbeat_led_gpio>;
> +
> + green-led {
> + label = "rockpis:green:power";
> + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + default-state = "on";
> + };
> +
> + blue-led {
> + label = "rockpis:blue:user";
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_h>;
> + reset-gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
> + };
> +
> + vcc5v0_sys: vcc5v0-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + vdd_core: vdd-core {
> + compatible = "pwm-regulator";
> + pwms = <&pwm0 0 5000 1>;
> + regulator-name = "vdd_core";
> + regulator-min-microvolt = <827000>;
> + regulator-max-microvolt = <1340000>;
> + regulator-init-microvolt = <1015000>;
> + regulator-settling-time-up-us = <250>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc5v0_sys>;
I think this should be pwm-supply = <&vcc5v0_sys>
see:
drivers/regulator/pwm-regulator.c
static const struct regulator_desc pwm_regulator_desc = {
.name = "pwm-regulator",
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
.supply_name = "pwm",
};
> + };
> +
> + vdd_log: vdd-log {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_log";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1050000>;
> + regulator-max-microvolt = <1050000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc_ddr: vcc-ddr {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc_1v8: vcc-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_1v8";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_io: vcc-io {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_io";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc5v0_otg: vcc5v0-otg {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_otg";
> + regulator-always-on;
> + gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + pinctrl-names = "default";
> + pinctrl-0 = <&otg_vbus_drv>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_core>;
> +};
> +
> +&emmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + supports-sd;
> + disable-wp;
> + non-removable;
> + num-slots = <1>;
> + vin-supply = <&vcc_io>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + max-frequeency = <150000000>;
> + supports-sd;
> + disable-wp;
> + num-slots = <1>;
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_det &sdmmc_bus4>;
> + card-detect-delay = <800>;
> + status = "okay";
> +};
> +
> +&spi2 {
> + status = "okay";
> + max-freq = <10000000>;
> +};
> +
> +&pinctrl {
> + pinctrl-names = "default";
> + pinctrl-0 = <&rtc_32k>;
> +
> + leds {
> + green_led_gio: green-led-gpio {
> + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + heartbeat_led_gpio: heartbeat-led-gpio {
> + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + otg_vbus_drv: otg-vbus-drv {
> + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + wifi_host_wake: wifi-host-wake {
> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +};
> +
> +&pwm0 {
> + status = "okay";
> + pinctrl-0 = <&pwm0_pin_pull_down>;
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + bus-width = <4>;
> + max-frequency = <1000000>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + supports-sdio;
> + keep-power-in-suspend;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + sd-uhs-sdr104;
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_xfer &uart4_rts &uart4_cts>;
> + status = "okay";
> +};
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add rock pi s dts support
2021-11-04 7:52 [PATCH] arm64: dts: rockchip: Add rock pi s dts support Akash Gajjar
@ 2021-11-04 16:12 ` Rob Herring
0 siblings, 0 replies; 5+ messages in thread
From: Rob Herring @ 2021-11-04 16:12 UTC (permalink / raw)
To: Akash Gajjar
Cc: Liang Chen, Johan Jonker, devicetree, Chen-Yu Tsai,
linux-rockchip, Peter Geis, Levin Du, heiko, linux-arm-kernel,
Rob Herring, Uwe Kleine-König, Jagan Teki, Alex Bee,
linux-kernel
On Thu, 04 Nov 2021 13:22:24 +0530, Akash Gajjar wrote:
> Rock pi s is RK3308 SBC from radxa. Rock pi s has a,
> - 256MB/512MB DDR3 RAM
> - micro sd, sd nand flash (optional on board 1/2/4/8Gb)
> - 100MB ethernet, PoE (optional)
> - onboard RTL8723DS 802.11 b/g/n wifi + Bluetooth 4.0 Module
> - 26-pin expansion header
> - USB2.0 Type-A HOST x1
> - USB Type-C DC 5V Power Supply
> - 2 LEDS, 2 Keys
>
> This patch enables
> - console on UART-2
> - nand flash
> - sd card
> - 100Mbps ethernet
> - USB2.0
>
> Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
> ---
> .../devicetree/bindings/arm/rockchip.yaml | 5 +
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3308-rock-pi-s.dts | 208 ++++++++++++++++++
> 3 files changed, 214 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
./Documentation/devicetree/bindings/arm/rockchip.yaml:473:1: [error] syntax error: found character '\t' that cannot start any token (syntax)
dtschema/dtc warnings/errors:
make[1]: *** Deleting file 'Documentation/devicetree/bindings/arm/rockchip.example.dts'
Traceback (most recent call last):
File "/usr/local/bin/dt-extract-example", line 45, in <module>
binding = yaml.load(open(args.yamlfile, encoding='utf-8').read())
File "/usr/local/lib/python3.8/dist-packages/ruamel/yaml/main.py", line 434, in load
return constructor.get_single_data()
File "/usr/local/lib/python3.8/dist-packages/ruamel/yaml/constructor.py", line 119, in get_single_data
node = self.composer.get_single_node()
File "_ruamel_yaml.pyx", line 706, in _ruamel_yaml.CParser.get_single_node
File "_ruamel_yaml.pyx", line 724, in _ruamel_yaml.CParser._compose_document
File "_ruamel_yaml.pyx", line 775, in _ruamel_yaml.CParser._compose_node
File "_ruamel_yaml.pyx", line 889, in _ruamel_yaml.CParser._compose_mapping_node
File "_ruamel_yaml.pyx", line 775, in _ruamel_yaml.CParser._compose_node
File "_ruamel_yaml.pyx", line 889, in _ruamel_yaml.CParser._compose_mapping_node
File "_ruamel_yaml.pyx", line 775, in _ruamel_yaml.CParser._compose_node
File "_ruamel_yaml.pyx", line 889, in _ruamel_yaml.CParser._compose_mapping_node
File "_ruamel_yaml.pyx", line 773, in _ruamel_yaml.CParser._compose_node
File "_ruamel_yaml.pyx", line 850, in _ruamel_yaml.CParser._compose_sequence_node
File "_ruamel_yaml.pyx", line 775, in _ruamel_yaml.CParser._compose_node
File "_ruamel_yaml.pyx", line 889, in _ruamel_yaml.CParser._compose_mapping_node
File "_ruamel_yaml.pyx", line 731, in _ruamel_yaml.CParser._compose_node
File "_ruamel_yaml.pyx", line 904, in _ruamel_yaml.CParser._parse_next_event
ruamel.yaml.scanner.ScannerError: while scanning a plain scalar
in "<unicode string>", line 472, column 22
found a tab character that violates indentation
in "<unicode string>", line 473, column 1
make[1]: *** [Documentation/devicetree/bindings/Makefile:20: Documentation/devicetree/bindings/arm/rockchip.example.dts] Error 1
make[1]: *** Waiting for unfinished jobs....
./Documentation/devicetree/bindings/arm/rockchip.yaml: while scanning a plain scalar
in "<unicode string>", line 472, column 22
found a tab character that violates indentation
in "<unicode string>", line 473, column 1
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/arm/rockchip.yaml: ignoring, error parsing file
warning: no schema found in file: ./Documentation/devicetree/bindings/arm/rockchip.yaml
make: *** [Makefile:1441: dt_binding_check] Error 2
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/1550787
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH] arm64: dts: rockchip: Add rock pi s dts support
@ 2021-11-04 7:52 Akash Gajjar
2021-11-04 16:12 ` Rob Herring
0 siblings, 1 reply; 5+ messages in thread
From: Akash Gajjar @ 2021-11-04 7:52 UTC (permalink / raw)
To: heiko
Cc: Akash Gajjar, Rob Herring, Chen-Yu Tsai, Jagan Teki, Levin Du,
Uwe Kleine-König, Alex Bee, Peter Geis, Liang Chen,
Johan Jonker, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Rock pi s is RK3308 SBC from radxa. Rock pi s has a,
- 256MB/512MB DDR3 RAM
- micro sd, sd nand flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- onboard RTL8723DS 802.11 b/g/n wifi + Bluetooth 4.0 Module
- 26-pin expansion header
- USB2.0 Type-A HOST x1
- USB Type-C DC 5V Power Supply
- 2 LEDS, 2 Keys
This patch enables
- console on UART-2
- nand flash
- sd card
- 100Mbps ethernet
- USB2.0
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
---
.../devicetree/bindings/arm/rockchip.yaml | 5 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3308-rock-pi-s.dts | 208 ++++++++++++++++++
3 files changed, 214 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 4aed16176434..69072db24cd6 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -515,6 +515,11 @@ properties:
- const: radxa,rockpi4
- const: rockchip,rk3399
+ - description: Radxa ROCK Pi S
+ items:
+ - const: radxa,rockpis
+ - const: rockchip,rk3308
+
- description: Radxa ROCK Pi E
items:
- const: radxa,rockpi-e
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 479906f3ad7b..c852bfb35387 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-ctouch2-of10.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-edimm2.2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-rock-pi-s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3318-a95x-z2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts
new file mode 100644
index 000000000000..0a8736de3fb3
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Akash Gajjar <gajjar04akash@gmail.com>
+ */
+
+/dts-v1/;
+#include "rk3308.dtsi"
+
+/ {
+ model = "Radxa ROCK Pi S";
+ compatible = "radxa,rockpis", "rockchip,rk3308";
+
+ aliases {
+ ethernet0 = &gmac;
+ mmc0 = &sdmmc;
+ mmc1 = &emmc;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&green_led_gio>, <&heartbeat_led_gpio>;
+
+ green-led {
+ label = "rockpis:green:power";
+ gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ default-state = "on";
+ };
+
+ blue-led {
+ label = "rockpis:blue:user";
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vdd_core: vdd-core {
+ compatible = "pwm-regulator";
+ pwms = <&pwm0 0 5000 1>;
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <827000>;
+ regulator-max-microvolt = <1340000>;
+ regulator-init-microvolt = <1015000>;
+ regulator-settling-time-up-us = <250>;
+ regulator-always-on;
+ regulator-boot-on;
+ pwm-supply = <&vcc5v0_sys>;
+ };
+
+ vdd_log: vdd-log {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc_ddr: vcc-ddr {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc_1v8: vcc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_io: vcc-io {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_io";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_otg: vcc5v0-otg {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_otg";
+ regulator-always-on;
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_core>;
+};
+
+&emmc {
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ non-removable;
+ status = "okay";
+};
+
+&gmac {
+ phy-supply = <&vcc_io>;
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
+ tx_delay = <0x28>;
+ rx_delay = <0x11>;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtc_32k>;
+
+ leds {
+ green_led_gio: green-led-gpio {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ heartbeat_led_gpio: heartbeat-led-gpio {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+ pinctrl-0 = <&pwm0_pin_pull_down>;
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc {
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <300>;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_xfer &uart4_rts &uart4_cts>;
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+
+ u2phy_host: host-port {
+ status = "okay";
+ };
+};
+
+&usb_host_ehci {
+ status = "okay";
+};
+
+&usb_host_ohci {
+ status = "okay";
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
end of thread, other threads:[~2021-11-04 16:12 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-15 17:33 [PATCH] arm64: dts: rockchip: add ROCK Pi S DTS support Akash Gajjar
2019-12-15 17:50 ` akash
2019-12-16 2:47 ` Andy Yan
2021-11-04 7:52 [PATCH] arm64: dts: rockchip: Add rock pi s dts support Akash Gajjar
2021-11-04 16:12 ` Rob Herring
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).