Re: [PATCH 5/6] arm64: dts: qcom: add sm8150 hdk dts

[Jonathan Marek <jonathan@marek.ca>]

On 5/28/20 11:01 PM, Bjorn Andersson wrote:
> On Sat 23 May 19:38 PDT 2020, Jonathan Marek wrote:
> 
>> Add initial HDK855 dts, based on sm8150-mtp, with a few changes.
>>
> 
> Happy to see this on the list Jonathan, just some minor things on the
> remoteproc nodes below.
> 
>> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
>> ---
>>   arch/arm64/boot/dts/qcom/Makefile       |   1 +
>>   arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 461 ++++++++++++++++++++++++
>>   2 files changed, 462 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/qcom/sm8150-hdk.dts
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index cc103f7020fd..e5dbd8b63951 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
>> +dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-mtp.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
> [..]
>> +/ {
>> +	model = "Qualcomm Technologies, Inc. SM8150 HDK";
>> +	compatible = "qcom,sm8150-hdk";
>> +
>> +	aliases {
>> +		serial0 = &uart2;
>> +	};
>> +
>> +	chosen {
>> +		stdout-path = "serial0:115200n8";
>> +	};
>> +
>> +	vph_pwr: vph-pwr-regulator {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vph_pwr";
>> +		regulator-min-microvolt = <3700000>;
>> +		regulator-max-microvolt = <3700000>;
>> +	};
>> +
>> +	/*
>> +	 * Apparently RPMh does not provide support for PM8150 S4 because it
>> +	 * is always-on; model it as a fixed regulator.
>> +	 */
> 
> One day we should stop being surprised by this and drop the "Apparently"
> from this comment ;)
> 

Had this copied from sm8150-mtp, dropped the comment entirely (to match 
sm8250-mtp dts).

>> +	vreg_s4a_1p8: pm8150-s4 {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vreg_s4a_1p8";
>> +
>> +		regulator-min-microvolt = <1800000>;
>> +		regulator-max-microvolt = <1800000>;
>> +
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +
>> +		vin-supply = <&vph_pwr>;
>> +	};
> [..]
>> +&remoteproc_adsp {
>> +	status = "okay";
> 
> It would be nice to see a
> 	firmware-name = "qcom/sm8150/adsp.mbn";
> 
> here. Because if we ever end up pushing firmware to linux-firmware this
> DTB would continue to work.
> 
> Use https://github.com/andersson/pil-squasher to get mbn files out of
> the mdt+bXX files for your testing (or just rename/symlink the mdt to
> mbn for now).
> 

Added the firmware-name fields as you suggested. One thing to note (it 
shouldn't matter for HDK), these firmwares can be modified by the device 
maker, so not all sm8150 will have the same adsp/cdsp/slpi firmware.

>> +};
>> +
>> +&remoteproc_cdsp {
>> +	status = "okay";
> 
> 	firmware-name = "qcom/sm8150/cdsp.mbn";
> 
>> +};
>> +
>> +&remoteproc_slpi {
>> +	status = "okay";
> 
> 	firmware-name = "qcom/sm8150/slpi.mbn";
> 
> Regards,
> Bjorn
> 
>> +};
>> +
>> +&tlmm {
>> +	gpio-reserved-ranges = <0 4>, <126 4>;
>> +};
>> +
>> +&uart2 {
>> +	status = "okay";
>> +};
>> +
>> +&ufs_mem_hc {
>> +	status = "okay";
>> +
>> +	reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
>> +
>> +	vcc-supply = <&vreg_l10a_2p5>;
>> +	vcc-max-microamp = <750000>;
>> +	vccq-supply = <&vreg_l9a_1p2>;
>> +	vccq-max-microamp = <700000>;
>> +	vccq2-supply = <&vreg_s4a_1p8>;
>> +	vccq2-max-microamp = <750000>;
>> +};
>> +
>> +&ufs_mem_phy {
>> +	status = "okay";
>> +
>> +	vdda-phy-supply = <&vdda_ufs_2ln_core_1>;
>> +	vdda-max-microamp = <90200>;
>> +	vdda-pll-supply = <&vreg_l3c_1p2>;
>> +	vdda-pll-max-microamp = <19000>;
>> +};
>> +
>> +&usb_1_hsphy {
>> +	status = "okay";
>> +	vdda-pll-supply = <&vdd_usb_hs_core>;
>> +	vdda33-supply = <&vdda_usb_hs_3p1>;
>> +	vdda18-supply = <&vdda_usb_hs_1p8>;
>> +};
>> +
>> +&usb_2_hsphy {
>> +	status = "okay";
>> +	vdda-pll-supply = <&vdd_usb_hs_core>;
>> +	vdda33-supply = <&vdda_usb_hs_3p1>;
>> +	vdda18-supply = <&vdda_usb_hs_1p8>;
>> +};
>> +
>> +&usb_1_qmpphy {
>> +	status = "okay";
>> +	vdda-phy-supply = <&vreg_l3c_1p2>;
>> +	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
>> +};
>> +
>> +&usb_2_qmpphy {
>> +	status = "okay";
>> +	vdda-phy-supply = <&vreg_l3c_1p2>;
>> +	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
>> +};
>> +
>> +&usb_1 {
>> +	status = "okay";
>> +};
>> +
>> +&usb_2 {
>> +	status = "okay";
>> +};
>> +
>> +&usb_1_dwc3 {
>> +	dr_mode = "peripheral";
>> +};
>> +
>> +&usb_2_dwc3 {
>> +	dr_mode = "host";
>> +};
>> -- 
>> 2.26.1
>>