Re: [PATCH 11/53] docs: trace: coresight: coresight-etm4x-reference.rst: avoid using UTF-8 chars

[Mathieu Poirier <mathieu.poirier@linaro.org>]

On Mon, May 10, 2021 at 12:26:23PM +0200, Mauro Carvalho Chehab wrote:
> While UTF-8 characters can be used at the Linux documentation,
> the best is to use them only when ASCII doesn't offer a good replacement.
> So, replace the occurences of the following UTF-8 characters:
> 
> 	- U+00a0 (' '): NO-BREAK SPACE
> 	- U+2018 ('‘'): LEFT SINGLE QUOTATION MARK
> 	- U+2019 ('’'): RIGHT SINGLE QUOTATION MARK
> 
> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>

> ---
>  .../coresight/coresight-etm4x-reference.rst      | 16 ++++++++--------
>  1 file changed, 8 insertions(+), 8 deletions(-)
> 
> diff --git a/Documentation/trace/coresight/coresight-etm4x-reference.rst b/Documentation/trace/coresight/coresight-etm4x-reference.rst
> index b64d9a9c79df..e8ddfc144d9a 100644
> --- a/Documentation/trace/coresight/coresight-etm4x-reference.rst
> +++ b/Documentation/trace/coresight/coresight-etm4x-reference.rst
> @@ -15,14 +15,14 @@ Root: ``/sys/bus/coresight/devices/etm<N>``
>  
>  The following paragraphs explain the association between sysfs files and the
>  ETMv4 registers that they effect. Note the register names are given without
> -the ‘TRC’ prefix.
> +the 'TRC' prefix.
>  
>  ----
>  
>  :File:            ``mode`` (rw)
>  :Trace Registers: {CONFIGR + others}
>  :Notes:
> -    Bit select trace features. See ‘mode’ section below. Bits
> +    Bit select trace features. See 'mode' section below. Bits
>      in this will cause equivalent programming of trace config and
>      other registers to enable the features requested.
>  
> @@ -89,7 +89,7 @@ the ‘TRC’ prefix.
>  :Notes:
>      Pair of addresses for a range selected by addr_idx. Include
>      / exclude according to the optional parameter, or if omitted
> -    uses the current ‘mode’ setting. Select comparator range in
> +    uses the current 'mode' setting. Select comparator range in
>      control register. Error if index is odd value.
>  
>  :Depends: ``mode, addr_idx``
> @@ -277,7 +277,7 @@ the ‘TRC’ prefix.
>  :Trace Registers: VICTLR{23:20}
>  :Notes:
>      Program non-secure exception level filters. Set / clear NS
> -    exception filter bits. Setting ‘1’ excludes trace from the
> +    exception filter bits. Setting '1' excludes trace from the
>      exception level.
>  
>  :Syntax:
> @@ -427,7 +427,7 @@ the ‘TRC’ prefix.
>  :Syntax:
>      ``echo idx > vmid_idx``
>  
> -    Where idx <  numvmidc
> +    Where idx <  numvmidc
>  
>  ----
>  
> @@ -628,7 +628,7 @@ the reset parameter::
>  
>  
>  
> -The ‘mode’ sysfs parameter.
> +The 'mode' sysfs parameter.
>  ---------------------------
>  
>  This is a bitfield selection parameter that sets the overall trace mode for the
> @@ -696,7 +696,7 @@ Bit assignments shown below:-
>      ETM_MODE_QELEM(val)
>  
>  **description:**
> -    ‘val’ determines level of Q element support enabled if
> +    'val' determines level of Q element support enabled if
>      implemented by the ETM [IDR0]
>  
>  
> @@ -780,7 +780,7 @@ Bit assignments shown below:-
>  ----
>  
>  *Note a)* On startup the ETM is programmed to trace the complete address space
> -using address range comparator 0. ‘mode’ bits 30 / 31 modify this setting to
> +using address range comparator 0. 'mode' bits 30 / 31 modify this setting to
>  set EL exclude bits for NS state in either user space (EL0) or kernel space
>  (EL1) in the address range comparator. (the default setting excludes all
>  secure EL, and NS EL2)
> -- 
> 2.30.2
>