Linux-EDAC Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH 0/2] Add EDAC support for Cadence ddr controller
@ 2020-02-25  9:38 Dhananjay Kangude
  2020-02-25  9:38 ` [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller Dhananjay Kangude
  2020-02-25  9:38 ` [PATCH 2/2] dt-bindings: edac: Add cadence ddr mc support Dhananjay Kangude
  0 siblings, 2 replies; 7+ messages in thread
From: Dhananjay Kangude @ 2020-02-25  9:38 UTC (permalink / raw)
  To: linux-edac
  Cc: bp, mchehab, tony.luck, james.morse, linux-kernel, mparab,
	robh+dt, devicetree, Dhananjay Kangude


These patches add new edac driver for Cadence ddr memory controller.
Cadence controller detects single(CE) and double(UE) bit errors during
memory operations(RMW). DDR controller raised the interrupt on detection
of the ecc error event and fill the data into registers. Driver handle
the interrupt event and notify edac subsystem about ecc errors.

The patch series has two patches:
1. Add driver support into edac subsystem
2. Add devicetree binding in yaml format

Dhananjay Kangude (2):
  EDAC/Cadence:Add EDAC driver for cadence memory controller
  dt-bindings: edac: Add cadence ddr mc support

 .../devicetree/bindings/edac/cdns,ddr-edac.yaml    |   56 ++
 drivers/edac/Kconfig                               |    7 +
 drivers/edac/Makefile                              |    1 +
 drivers/edac/cadence_edac.c                        |  615 ++++++++++++++++++++
 4 files changed, 679 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/edac/cdns,ddr-edac.yaml
 create mode 100644 drivers/edac/cadence_edac.c


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller
  2020-02-25  9:38 [PATCH 0/2] Add EDAC support for Cadence ddr controller Dhananjay Kangude
@ 2020-02-25  9:38 ` Dhananjay Kangude
  2020-02-25 22:04   ` kbuild test robot
                     ` (2 more replies)
  2020-02-25  9:38 ` [PATCH 2/2] dt-bindings: edac: Add cadence ddr mc support Dhananjay Kangude
  1 sibling, 3 replies; 7+ messages in thread
From: Dhananjay Kangude @ 2020-02-25  9:38 UTC (permalink / raw)
  To: linux-edac
  Cc: bp, mchehab, tony.luck, james.morse, linux-kernel, mparab,
	robh+dt, devicetree, Dhananjay Kangude

Added edac platform driver for Cadence DDR controller which
notify the ecc events based on the single or double bit errors
during memory operations.

Signed-off-by: Dhananjay Kangude <dkangude@cadence.com>
---
 drivers/edac/Kconfig        |    7 +
 drivers/edac/Makefile       |    1 +
 drivers/edac/cadence_edac.c |  615 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 623 insertions(+), 0 deletions(-)
 create mode 100644 drivers/edac/cadence_edac.c

diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
index fe2eb89..4bea379 100644
--- a/drivers/edac/Kconfig
+++ b/drivers/edac/Kconfig
@@ -530,4 +530,11 @@ config EDAC_DMC520
 	  Support for error detection and correction on the
 	  SoCs with ARM DMC-520 DRAM controller.
 
+config EDAC_CADENCE
+	tristate "Candence DDR Memory Controller ECC"
+	help
+	  Support for error detection and correction on the Cadence DDR
+	  memory controller. The driver provide the statistics  for single bit(CE)
+	  and double bit(UE) error correction.
+
 endif # EDAC
diff --git a/drivers/edac/Makefile b/drivers/edac/Makefile
index 269e151..a56cf2e 100644
--- a/drivers/edac/Makefile
+++ b/drivers/edac/Makefile
@@ -88,3 +88,4 @@ obj-$(CONFIG_EDAC_QCOM)			+= qcom_edac.o
 obj-$(CONFIG_EDAC_ASPEED)		+= aspeed_edac.o
 obj-$(CONFIG_EDAC_BLUEFIELD)		+= bluefield_edac.o
 obj-$(CONFIG_EDAC_DMC520)		+= dmc520_edac.o
+obj-$(CONFIG_EDAC_CADENCE)		+= cadence_edac.o
diff --git a/drivers/edac/cadence_edac.c b/drivers/edac/cadence_edac.c
new file mode 100644
index 0000000..3887db5
--- /dev/null
+++ b/drivers/edac/cadence_edac.c
@@ -0,0 +1,615 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Cadence DDR4-ECC EDAC Driver.
+ *
+ * * Copyright (C) 2018-2019 Cadence Design Systems.
+ *
+ * * Authors: Dhananjay Kangude <dkangude@cadence.com>,
+ */
+#include <linux/init.h>
+#include <linux/edac.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/module.h>
+#include <linux/uaccess.h>
+#include <linux/delay.h>
+#include "edac_module.h"
+
+#define CDNS_EDAC_MOD_NAME "cadence-edac"
+#define FORCED_ECC_ERR_EVENT_SUPPORT	1
+/* Number of cs_rows needed per memory controller */
+#define CDNS_EDAC_NR_CSROWS		2
+
+/* Number of channels per memory controller */
+#define CDNS_EDAC_NR_CHANS		1
+
+/* Granularity of reported error in bytes */
+#define CDNS_EDAC_ERR_GRAIN		1
+
+#define MEM_TYPE_DDR4			0xA
+/* CDNS DDR4 Controller Registers */
+#define DDR_CTL_MEM_TYPE_REG		0x000
+#define DDR_CTL_MEM_WIDTH_REG		0x00c
+#define DDR_CTL_CONTROLLER_BUSY		0x2f0
+
+/* ECC Controller Registers */
+#define ECC_CTL_CONTROL_0_REG		0x254
+#define ECC_CTL_CONTROL_1_REG		0x258
+
+#define ECC_CTL_SCRUB_CONTROL_0		0x280
+#define ECC_CTL_SCRUB_CONTROL_1		0x284
+#define ECC_CTL_SCRUB_CONTROL_2		0x288
+#define ECC_CTL_SCRUB_START_ADDR_L	0x28c
+#define ECC_CTL_SCRUB_START_ADDR_H	0x290
+#define ECC_CTL_SCRUB_END_ADDR_L	0x294
+#define ECC_CTL_SCRUB_END_ADDR_H	0x298
+
+#define ECC_SIG_ECC_C_ADDR_L		0x26c
+#define ECC_SIG_ECC_C_ADDR_H		0x270
+#define ECC_SIG_ECC_C_DATA_L		0x274
+#define ECC_SIG_ECC_C_DATA_H		0x278
+#define ECC_SIG_ECC_C_ID		0x27c
+#define ECC_SIG_ECC_C_SYND		0x270
+#define ECC_SIG_ECC_U_ADDR_L		0x25c
+#define ECC_SIG_ECC_U_ADDR_H		0x25c
+#define ECC_SIG_ECC_U_DATA_L		0x264
+#define ECC_SIG_ECC_U_DATA_H		0x268
+#define ECC_SIG_ECC_U_ID		0x27c
+#define ECC_SIG_ECC_U_SYND		0x260
+
+#define ECC_CTL_INT_STATUS_L		0x310
+#define ECC_CTL_INT_ACK_L		0x330
+#define ECC_CTL_INT_MASK_0_L		0x350
+
+/*ECC Scrub Macros */
+#define ECC_SCRUB_IN_PROGRESS		BIT(8)
+#define ECC_SCRUB_MODE			BIT(0)
+#define ECC_SCRUB_START			BIT(0)
+#define ECC_SCRUB_LEN_SHIFT		(16)
+#define ECC_SCRUB_IDLE_CNT		GENMASK(15, 0)
+#define ECC_SCRUB_LEN			GENMASK(27, 16)
+#define ECC_CTL_SCRUB_ADDR_L_MASK	GENMASK(31, 0)
+#define ECC_CTL_SCRUB_ADDR_H_MASK	GENMASK(1, 0)
+
+/* Control register width definitions */
+#define WDTH_16				(2)
+#define WDTH_32				(1)
+#define WDTH_64				(0)
+#define CTL_REG_WIDTH_SHIFT		(32)
+#define USER_WORD_SPLIT_WIDTH		(8)
+#define CTL_CONTROLLER_BUSY_FLAG	BIT(16)
+#define CTL_MEM_MAX_WIDTH_MASK		GENMASK(4, 0)
+
+/* ECC Control Macros */
+#define ECC_CTL_FORCE_WC		BIT(16)
+#define ECC_CTL_AUTO_CURRUPT_DISABLE	BIT(16)
+#define ECC_CTL_AUTO_WRITEBACK_EN	BIT(24)
+#define ECC_CTL_ECC_ENABLE		GENMASK(9, 8)
+#define ECC_CTL_MTYPE_MASK		GENMASK(11, 8)
+#define ECC_CTL_XOR_BITS_MASK		GENMASK(15, 0)
+
+/* ECC Status Macros */
+
+/* ECC IRQ Macros */
+#define ECC_INT_CE_EVENT		BIT(0)
+#define ECC_INT_SECOND_CE_EVENT		BIT(1)
+#define ECC_INT_UE_EVENT		BIT(2)
+#define ECC_INT_SECOND_UE_EVENT		BIT(3)
+#define ECC_INT_WRITEBACK_UNHANDLED	BIT(6)
+#define ECC_INT_SCRUB_DONE		BIT(7)
+#define ECC_INT_SCRUB_CE_EVENT		BIT(8)
+#define ECC_INT_MASK_ALL_H		BIT(8)
+#define ECC_INT_CE_UE_MASK		GENMASK(3, 0)
+#define ECC_CE_INTR_MASK		GENMASK(1, 0)
+#define ECC_UE_INTR_MASK		GENMASK(3, 2)
+#define ECC_CTL_INT_ENABLE_MASK		GENMASK(15, 0)
+/* ECC Signature Macros */
+#define ECC_SIG_ECC_C_ID_SHIFT		8
+#define ECC_SIG_ECC_C_SYND_SHIFT	8
+#define ECC_SIG_ECC_C_ADDR_H_MASK	GENMASK(1, 0)
+#define ECC_SIG_ECC_C_ID_MASK		GENMASK(31, 16)
+#define ECC_SIG_ECC_C_SYND_MASK		GENMASK(15, 8)
+
+#define ECC_SIG_ECC_U_ID_SHIFT		0
+#define ECC_SIG_ECC_U_SYND_SHIFT	8
+#define ECC_SIG_ECC_U_ADDR_H_MASK	GENMASK(1, 0)
+#define ECC_SIG_ECC_U_ID_MASK		GENMASK(15, 0)
+#define ECC_SIG_ECC_U_SYND_MASK		GENMASK(15, 8)
+
+/* Syndrome values */
+#define ECC_DOUBLE_MULTI_ERR_SYND	0x03
+
+char data_synd[] = {
+			0xf4, 0xf1, 0xec, 0xea, 0xe9, 0xe6, 0xe5, 0xe3,
+			0xdc, 0xda, 0xd9, 0xd6, 0xd5, 0xd3, 0xce, 0xcb,
+			0xb5, 0xb0, 0xad, 0xab, 0xa8, 0xa7, 0xa4, 0xa2,
+			0x9d, 0x9b, 0x98, 0x97, 0x94, 0x92, 0x8f, 0x8a,
+			0x75, 0x70, 0x6d, 0x6b, 0x68, 0x67, 0x64, 0x62,
+			0x5e, 0x5b, 0x58, 0x57, 0x54, 0x52, 0x4f, 0x4a,
+			0x34, 0x31, 0x2c, 0x2a, 0x29, 0x26, 0x25, 0x23,
+			0x1c, 0x1a, 0x19, 0x16, 0x15, 0x13, 0x0e, 0x0b
+		  };
+
+char check_synd[] = {0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80};
+
+/**
+ * struct cdns_platform_data -  cadence platform data structure.
+ * @quirks:             To differentiate IP features.
+ */
+struct cdns_platform_data {
+	int quirks;
+};
+
+/**
+ * struct cdns_edac_priv_data - edac device private instance data.
+ * @reg:	        Base address of the DDR controller.
+ * @ce_cnt:             Correctable Error count.
+ * @ue_cnt:             Uncorrectable Error count.
+ */
+struct cdns_edac_priv_data {
+	void __iomem *reg;
+	u32 ce_cnt;
+	u32 ue_cnt;
+#ifdef CONFIG_EDAC_DEBUG
+	struct cdns_platform_data *p;
+#endif
+};
+
+/**
+ * init_mem_layout -  Set address Map as per the mc design.
+ * @mci:   memory controller information.
+ *
+ * Set Address Map as per mc instance .
+ *
+ * Return: none.
+ */
+static void init_mem_layout(struct mem_ctl_info *mci)
+{
+	struct cdns_edac_priv_data *priv = mci->pvt_info;
+	struct csrow_info *csi;
+	struct dimm_info *dimm;
+	struct sysinfo inf;
+	enum mem_type mtype;
+	u32 val, width;
+	u32 size, row;
+	u8 j;
+
+	dimm = EDAC_DIMM_PTR(mci->layers, mci->dimms, mci->n_layers, 0, 0, 0);
+
+	si_meminfo(&inf);
+	for (row = 0; row < mci->nr_csrows; row++) {
+		csi = mci->csrows[row];
+		size = inf.totalram * inf.mem_unit;
+
+		for (j = 0; j < csi->nr_channels; j++) {
+			dimm            = csi->channels[j]->dimm;
+			dimm->edac_mode = EDAC_FLAG_SECDED;
+			/* Get memory type by reading hw registers*/
+			val = readl(priv->reg + DDR_CTL_MEM_TYPE_REG);
+			mtype = val & ECC_CTL_MTYPE_MASK;
+
+			if (mtype == MEM_TYPE_DDR4)
+				dimm->mtype = MEM_DDR4;
+			else
+				dimm->mtype = MEM_EMPTY;
+
+			/*Get EDAC devtype width for the current mc*/
+			width = (readl(priv->reg + DDR_CTL_MEM_WIDTH_REG) &
+				       CTL_MEM_MAX_WIDTH_MASK);
+			switch (width) {
+			case WDTH_16:
+				dimm->dtype  = DEV_X2;
+				break;
+			case WDTH_32:
+				dimm->dtype  = DEV_X4;
+				break;
+			case WDTH_64:
+				dimm->dtype  = DEV_X8;
+				break;
+			default:
+				dimm->dtype = DEV_UNKNOWN;
+			}
+
+			dimm->nr_pages  = (size >> PAGE_SHIFT) /
+					   csi->nr_channels;
+			dimm->grain     = CDNS_EDAC_ERR_GRAIN;
+		}
+	}
+}
+
+/**
+ * edac_ecc_isr - Interrupt Handler for ECC interrupts.
+ * @irq:        IRQ number.
+ * @dev_id:     Device ID.
+ *
+ * Return: IRQ_NONE, if interrupt not set or IRQ_HANDLED otherwise.
+ */
+static irqreturn_t edac_ecc_isr(int irq, void *dev_id)
+{
+	struct mem_ctl_info *mci = dev_id;
+	struct cdns_edac_priv_data *priv;
+	u32 intr_status;
+	u32 val;
+	u32 sig_val_l, sig_val_h;
+	u32 err_c_id, err_u_id;
+	u32 err_c_synd, err_u_synd;
+	u64 err_c_addr = 0x0, err_u_addr = 0x0;
+	u64 err_c_data = 0x0, err_u_data = 0x0;
+
+	priv = mci->pvt_info;
+
+	/* Check the intr status and confirm ECC error intr */
+	intr_status = readl(priv->reg + ECC_CTL_INT_STATUS_L);
+
+	edac_dbg(3, "InterruptStatus : 0x%x\n", intr_status);
+	val = intr_status & (ECC_INT_CE_UE_MASK);
+	if (!((val & ECC_CE_INTR_MASK) || (val & ECC_UE_INTR_MASK)))
+		return IRQ_NONE;
+
+	if (val & ECC_CE_INTR_MASK) {
+		sig_val_l = readl(priv->reg + ECC_SIG_ECC_C_ADDR_L);
+		sig_val_h = (readl(priv->reg + ECC_SIG_ECC_C_ADDR_H) &
+			     ECC_SIG_ECC_C_ADDR_H_MASK);
+		err_c_addr = (((err_c_addr | sig_val_h) <<
+				CTL_REG_WIDTH_SHIFT) | sig_val_l);
+
+		sig_val_l = readl(priv->reg + ECC_SIG_ECC_C_DATA_L);
+		sig_val_h = readl(priv->reg + ECC_SIG_ECC_C_DATA_H);
+		err_c_data = (((err_c_data | sig_val_h) <<
+				CTL_REG_WIDTH_SHIFT) | sig_val_l);
+
+		err_c_id = ((readl(priv->reg + ECC_SIG_ECC_C_ID) &
+			     ECC_SIG_ECC_C_ID_MASK) >>
+			     ECC_SIG_ECC_C_ID_SHIFT);
+
+		err_c_synd = ((readl(priv->reg + ECC_SIG_ECC_C_SYND) &
+			       ECC_SIG_ECC_C_SYND_MASK) >>
+			       ECC_SIG_ECC_C_SYND_SHIFT);
+		priv->ce_cnt = priv->ce_cnt + 1;
+
+		edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci,
+				     1,
+				     err_c_addr >> PAGE_SHIFT,
+				     err_c_addr & ~PAGE_MASK,
+				     err_c_synd, 0, 0, -1,
+				     mci->ctl_name, "");
+
+		/* Clear the interrupt source */
+		if (val & ECC_INT_CE_EVENT)
+			writel(ECC_INT_CE_EVENT, priv->reg + ECC_CTL_INT_ACK_L);
+		else if (val & ECC_INT_SECOND_CE_EVENT)
+			writel(ECC_INT_SECOND_CE_EVENT,
+			       priv->reg + ECC_CTL_INT_ACK_L);
+		else
+			edac_printk(KERN_ERR, EDAC_MC, "Failed to clear IRQ\n");
+	}
+
+	if (val & ECC_UE_INTR_MASK) {
+		sig_val_l = readl(priv->reg + ECC_SIG_ECC_U_ADDR_L);
+		sig_val_h = (readl(priv->reg + ECC_SIG_ECC_U_ADDR_H) &
+			     ECC_SIG_ECC_U_ADDR_H_MASK);
+		err_u_addr = (((err_u_addr | sig_val_h) <<
+				CTL_REG_WIDTH_SHIFT) | sig_val_l);
+
+		sig_val_l = readl(priv->reg + ECC_SIG_ECC_U_DATA_L);
+		sig_val_h = readl(priv->reg + ECC_SIG_ECC_U_DATA_H);
+		err_u_data = (((err_u_data | sig_val_h) <<
+				CTL_REG_WIDTH_SHIFT) | sig_val_l);
+
+		err_u_id = ((readl(priv->reg + ECC_SIG_ECC_U_ID) &
+			     ECC_SIG_ECC_U_ID_MASK) >>
+			     ECC_SIG_ECC_U_ID_SHIFT);
+
+		err_u_synd = ((readl(priv->reg + ECC_SIG_ECC_U_SYND) &
+			       ECC_SIG_ECC_U_SYND_MASK) >>
+			       ECC_SIG_ECC_U_SYND_SHIFT);
+		priv->ue_cnt = priv->ue_cnt + 1;
+
+		edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci,
+				     1,
+				     err_u_addr >> PAGE_SHIFT,
+				     err_u_addr & ~PAGE_MASK,
+				     err_u_synd, 0, 0, -1,
+				     mci->ctl_name, "");
+
+		/* Clear the interrupt source */
+		if (val & ECC_INT_UE_EVENT)
+			writel(ECC_INT_UE_EVENT, priv->reg + ECC_CTL_INT_ACK_L);
+		else if (val & ECC_INT_SECOND_UE_EVENT)
+			writel(ECC_INT_SECOND_UE_EVENT,
+			       priv->reg + ECC_CTL_INT_ACK_L);
+		else
+			edac_printk(KERN_ERR, EDAC_MC, "Failed to clear IRQ\n");
+	}
+
+	edac_dbg(3, "Total error count CE %d UE %d\n",
+		 priv->ce_cnt, priv->ue_cnt);
+
+	return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_EDAC_DEBUG
+/**
+ * forced_ecc_error_show/store - Sysfs atrribute functions.
+ * @dev: Pointer to device structure.
+ * @mattr: Pointer to device attributes.
+ * @data : Data send by User space and stored in file.
+ * Return: as SUCCESS,Total number of characters written otherwise
+ *         negative value.
+ */
+static ssize_t forced_ecc_error_show(struct device *dev,
+				     struct device_attribute *mattr,
+				     char *data)
+{
+	return sprintf(data, "CDNS-DDR4 Force Injection Help:\n"
+		       "CE/UE: Corrected/Uncorrected\n"
+		       "checkcode/data:source\n"
+		       "user_word [0-1]:subpart of data\n"
+		       "bit [0-31]:bit number\n");
+}
+
+static ssize_t forced_ecc_error_store(struct device *dev,
+				      struct device_attribute *mattr,
+				      const char *data, size_t count)
+{
+	struct mem_ctl_info *mci = to_mci(dev);
+	struct cdns_edac_priv_data *priv = mci->pvt_info;
+	int	args_cnt;
+	int	ret;
+	char	**args;
+	char buf[1000];
+	u32	regval;
+	u8	user_word;
+	u8	bit_no;
+
+	/* Read sysfs params into buffer*/
+	snprintf(buf, min_t(size_t, sizeof(buf) - 1, count), "%s\n", data);
+	/*Split string buffer into separate parameters*/
+	args = argv_split(GFP_KERNEL, buf, &args_cnt);
+
+	ret = kstrtou8(args[2], 0, &user_word);
+	if (ret)
+		return ret;
+
+	ret = kstrtou8(args[3], 0, &bit_no);
+	if (ret)
+		return ret;
+
+	/* Check ecc enabled */
+	if (readl(priv->reg + ECC_CTL_CONTROL_0_REG) & ECC_CTL_ECC_ENABLE) {
+		/* Check no write operation pending to controller*/
+		while (readl(priv->reg + DDR_CTL_CONTROLLER_BUSY) &
+			     CTL_CONTROLLER_BUSY_FLAG) {
+			usleep_range(1000, 10000);
+		}
+		/* Write appropriate syndrome to xor_check_bit*/
+		if (!strcmp(args[0], "CE")) {
+			if (!strcmp(args[1], "checkcode")) {
+				regval = readl(priv->reg +
+					       ECC_CTL_CONTROL_1_REG);
+				regval = (regval & ~(ECC_CTL_XOR_BITS_MASK)) |
+					(check_synd[bit_no] <<
+					(USER_WORD_SPLIT_WIDTH * user_word));
+				writel(regval,
+				       priv->reg + ECC_CTL_CONTROL_1_REG);
+			} else if (!strcmp(args[1], "data")) {
+				regval = readl(priv->reg +
+					       ECC_CTL_CONTROL_1_REG);
+				regval = (regval & ~(ECC_CTL_XOR_BITS_MASK)) |
+					(data_synd[bit_no] <<
+					(USER_WORD_SPLIT_WIDTH * user_word));
+				writel(regval,
+				       priv->reg + ECC_CTL_CONTROL_1_REG);
+			}
+			/* Enable the ECC writeback_en for corrected error */
+			regval = readl(priv->reg + ECC_CTL_CONTROL_1_REG);
+			writel((regval | ECC_CTL_AUTO_WRITEBACK_EN),
+			       priv->reg + ECC_CTL_CONTROL_1_REG);
+		} else if (!strcmp(args[0], "UE")) {
+			writel(ECC_DOUBLE_MULTI_ERR_SYND,
+			       priv->reg + ECC_CTL_CONTROL_1_REG);
+		}
+
+		/* Assert fwc */
+		writel((ECC_CTL_FORCE_WC |
+			readl(priv->reg + ECC_CTL_CONTROL_0_REG)),
+			priv->reg + ECC_CTL_CONTROL_0_REG);
+	}
+	return count;
+}
+
+static DEVICE_ATTR_RW(forced_ecc_error);
+static int edac_create_sysfs_attributes(struct mem_ctl_info *mci)
+{
+	int rc;
+
+	rc = device_create_file(&mci->dev, &dev_attr_forced_ecc_error);
+	if (rc < 0)
+		return rc;
+	return 0;
+}
+
+static void edac_remove_sysfs_attributes(struct mem_ctl_info *mci)
+{
+	device_remove_file(&mci->dev, &dev_attr_forced_ecc_error);
+}
+
+#endif
+
+static const struct cdns_platform_data cdns_edac = {
+#ifdef CONFIG_EDAC_DEBUG
+	.quirks = FORCED_ECC_ERR_EVENT_SUPPORT,
+#endif
+};
+
+static const struct of_device_id cdns_edac_of_match[] = {
+	{ .compatible = "cdns,cadence-ddr4-mc-edac", .data = &cdns_edac },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, cdns_edac_of_match);
+
+/**
+ * cdns_edac_mc_probe - bind cdns mc controller driver to framework.
+ * @pdev:  platform device.
+ *
+ * Probe a memory controller for binding with the driver.
+ *
+ * Return: 0 if binding of the controller instance is successful;
+ * otherwise, < 0 on error.
+ */
+
+static int cdns_edac_mc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	void __iomem *reg;
+	struct mem_ctl_info *mci;
+	struct edac_mc_layer layers[1];
+	const struct of_device_id *id;
+	struct cdns_edac_priv_data *priv_data;
+	int irq, ret = -ENODEV;
+#ifdef CONFIG_EDAC_DEBUG
+	const struct cdns_platform_data *p;
+	struct dentry *root;
+#endif
+
+	id = of_match_device(cdns_edac_of_match, &pdev->dev);
+	if (!id)
+		return -ENODEV;
+
+#ifdef CONFIG_EDAC_DEBUG
+	p = of_device_get_match_data(&pdev->dev);
+	if (!p)
+		return -ENODEV;
+#endif
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	reg = devm_ioremap_resource(dev, res);
+	if (IS_ERR(reg)) {
+		edac_printk(KERN_ERR, CDNS_EDAC_MOD_NAME,
+			    "cdns DDR4 mc regs are not defined\n");
+		return PTR_ERR(reg);
+	}
+
+	edac_printk(KERN_ERR, CDNS_EDAC_MOD_NAME,
+		    "IO mapped reg addr: %p\n", reg);
+	layers[0].type = EDAC_MC_LAYER_CHIP_SELECT;
+	layers[0].size = 1;
+	layers[0].is_virt_csrow = true;
+
+	mci = edac_mc_alloc(0, ARRAY_SIZE(layers), layers,
+			    sizeof(struct cdns_edac_priv_data));
+	if (!mci) {
+		edac_printk(KERN_ERR, CDNS_EDAC_MOD_NAME,
+			    "Failed memory allocation for mc instance\n");
+		return -ENOMEM;
+	}
+	mci->pdev = &pdev->dev;
+	priv_data = mci->pvt_info;
+	priv_data->reg = reg;
+	priv_data->ce_cnt = 0;
+	priv_data->ue_cnt = 0;
+	platform_set_drvdata(pdev, mci);
+	/* Initialize controller capabilities */
+	mci->mtype_cap = MEM_FLAG_DDR4;
+	mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_SECDED;
+	mci->scrub_cap = SCRUB_UNKNOWN;
+	mci->scrub_mode = SCRUB_HW_PROG;
+	mci->edac_cap = EDAC_FLAG_SECDED;
+	mci->ctl_name = id->compatible;
+	mci->dev_name = dev_name(&pdev->dev);
+	mci->mod_name = CDNS_EDAC_MOD_NAME;
+	mci->ctl_page_to_phys = NULL;
+
+	/* Interrupt feature is supported by cadence mc */
+	edac_op_state = EDAC_OPSTATE_INT;
+	init_mem_layout(mci);
+
+	/* Setup Interrupt handler for ECC */
+	irq = platform_get_irq(pdev, 0);
+	if (!irq) {
+		edac_printk(KERN_ERR, CDNS_EDAC_MOD_NAME,
+			    "irq number not defined for ecc.\n");
+		goto err;
+	}
+	ret = devm_request_irq(dev, irq, edac_ecc_isr, 0,
+			       "cdns-edac-mc-ecc-irq", mci);
+	if (ret) {
+		edac_printk(KERN_ERR, CDNS_EDAC_MOD_NAME,
+			    "request_irq fail for CDNS_EDAC irq\n");
+		goto err;
+	}
+	ret = edac_mc_add_mc(mci);
+	if (ret) {
+		edac_printk(KERN_ERR, CDNS_EDAC_MOD_NAME,
+			    "Failed to register with EDAC core\n");
+		goto err;
+	}
+
+#ifdef CONFIG_EDAC_DEBUG
+	if (p->quirks && FORCED_ECC_ERR_EVENT_SUPPORT) {
+		if (edac_create_sysfs_attributes(mci)) {
+			edac_printk(KERN_ERR, CDNS_EDAC_MOD_NAME,
+				    "Failed to create sysfs entries\n");
+			goto err;
+		}
+	}
+#endif
+	/* Enable & set CE/UE Interrupts for DDR4 Controller */
+	writel(~(ECC_CTL_INT_ENABLE_MASK),
+	       priv_data->reg + ECC_CTL_INT_MASK_0_L);
+
+	/* Start capturing the correctable and uncorrectable errors.
+	 * Write 1 to enable.
+	 */
+	writel(ECC_CTL_ECC_ENABLE, priv_data->reg + ECC_CTL_CONTROL_0_REG);
+	return 0;
+
+err:
+	edac_mc_free(mci);
+	return ret;
+}
+
+/**
+ * cdns_edac_mc_remove - Unbind driver from controller.
+ * @pdev:  Platform device.
+ *
+ * Return: 0
+ */
+
+static int cdns_edac_mc_remove(struct platform_device *pdev)
+{
+	struct mem_ctl_info *mci = platform_get_drvdata(pdev);
+	struct cdns_edac_priv_data *priv = mci->pvt_info;
+
+	/* Disable All ECC Interrupts for DDR4 Controller */
+	writel(ECC_CTL_INT_ENABLE_MASK, priv->reg + ECC_CTL_INT_MASK_0_L);
+
+	/* Disable ecc feature before removing driver by writing 0.*/
+	writel(~(ECC_CTL_ECC_ENABLE), priv->reg + ECC_CTL_CONTROL_0_REG);
+
+#ifdef CONFIG_EDAC_DEBUG
+	edac_remove_sysfs_attributes(mci);
+#endif
+	edac_mc_del_mc(&pdev->dev);
+	edac_mc_free(mci);
+
+	return 0;
+}
+
+static struct platform_driver cdns_edac_mc_driver = {
+	.driver = {
+		   .name = "cadence-edac",
+		   .of_match_table = cdns_edac_of_match,
+	},
+	.probe = cdns_edac_mc_probe,
+	.remove = cdns_edac_mc_remove,
+};
+
+module_platform_driver(cdns_edac_mc_driver);
+
+MODULE_AUTHOR("Cadence");
+MODULE_DESCRIPTION("Cadence DDR4 Controller ECC driver");
+MODULE_LICENSE("GPL v2");
-- 
1.7.1


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH 2/2] dt-bindings: edac: Add cadence ddr mc support
  2020-02-25  9:38 [PATCH 0/2] Add EDAC support for Cadence ddr controller Dhananjay Kangude
  2020-02-25  9:38 ` [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller Dhananjay Kangude
@ 2020-02-25  9:38 ` Dhananjay Kangude
  2020-02-25 16:58   ` Rob Herring
  1 sibling, 1 reply; 7+ messages in thread
From: Dhananjay Kangude @ 2020-02-25  9:38 UTC (permalink / raw)
  To: linux-edac
  Cc: bp, mchehab, tony.luck, james.morse, linux-kernel, mparab,
	robh+dt, devicetree, Dhananjay Kangude

Add documentation for cadence ddr memory controller EDAC DTS bindings

Signed-off-by: Dhananjay Kangude <dkangude@cadence.com>
---
 .../devicetree/bindings/edac/cdns,ddr-edac.yaml    |   56 ++++++++++++++++++++
 1 files changed, 56 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/edac/cdns,ddr-edac.yaml

diff --git a/Documentation/devicetree/bindings/edac/cdns,ddr-edac.yaml b/Documentation/devicetree/bindings/edac/cdns,ddr-edac.yaml
new file mode 100644
index 0000000..df70647
--- /dev/null
+++ b/Documentation/devicetree/bindings/edac/cdns,ddr-edac.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/edac/cdns,ddr-edac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence DDR IP with ECC support (EDAC)
+
+description:
+  This binding describes the Cadence DDR/LPDDR IP with ECC feature enabled
+  to detect and correct CE/UE errors.
+
+maintainers:
+  - Dhananjay Kangdue <dkangude@cadence.com>
+
+properties:
+  compatible:
+    enum:
+      - cdns,cadence-ddr4-mc-edac
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 1
+
+  reg:
+    minItems: 1
+    maxItems: 2
+    items:
+      - description:
+          Register block of DDR/LPDDR apb registers up to mapped area.
+          Mapped area contains the register set for memory controller,
+          phy and PI module register set doesn't part of this mapping.
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    edac: edac@fd100000 {
+        compatible = "cdns,cadence-ddr4-mc-edac";
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges;
+        reg = <0xfd100000 0x4000>;
+        interrupts = <0x00 0x01 0x04>;
+        };
+...
-- 
1.7.1


^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH 2/2] dt-bindings: edac: Add cadence ddr mc support
  2020-02-25  9:38 ` [PATCH 2/2] dt-bindings: edac: Add cadence ddr mc support Dhananjay Kangude
@ 2020-02-25 16:58   ` Rob Herring
  0 siblings, 0 replies; 7+ messages in thread
From: Rob Herring @ 2020-02-25 16:58 UTC (permalink / raw)
  To: Dhananjay Kangude
  Cc: linux-edac, bp, mchehab, tony.luck, james.morse, linux-kernel,
	mparab, robh+dt, devicetree, Dhananjay Kangude

On Tue, 25 Feb 2020 10:38:56 +0100, Dhananjay Kangude wrote:
> Add documentation for cadence ddr memory controller EDAC DTS bindings
> 
> Signed-off-by: Dhananjay Kangude <dkangude@cadence.com>
> ---
>  .../devicetree/bindings/edac/cdns,ddr-edac.yaml    |   56 ++++++++++++++++++++
>  1 files changed, 56 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/edac/cdns,ddr-edac.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

Documentation/devicetree/bindings/display/simple-framebuffer.example.dts:21.16-37.11: Warning (chosen_node_is_root): /example-0/chosen: chosen node must be at root node
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/edac/cdns,ddr-edac.example.dt.yaml: edac@fd100000: 'ranges' does not match any of the regexes: 'pinctrl-[0-9]+'

See https://patchwork.ozlabs.org/patch/1243950
Please check and re-submit.

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller
  2020-02-25  9:38 ` [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller Dhananjay Kangude
@ 2020-02-25 22:04   ` kbuild test robot
  2020-02-26  2:11   ` [RFC PATCH] EDAC/Cadence: data_synd[] can be static kbuild test robot
  2020-02-26  3:26   ` [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller kbuild test robot
  2 siblings, 0 replies; 7+ messages in thread
From: kbuild test robot @ 2020-02-25 22:04 UTC (permalink / raw)
  To: Dhananjay Kangude; +Cc: kbuild-all, linux-edac

[-- Attachment #1: Type: text/plain, Size: 3799 bytes --]

Hi Dhananjay,

Thank you for the patch! Yet something to improve:

[auto build test ERROR on ras/edac-for-next]
[also build test ERROR on next-20200225]
[cannot apply to v5.6-rc3]
[if your patch is applied to the wrong git tree, please drop us a note to help
improve the system. BTW, we also suggest to use '--base' option to specify the
base tree in git format-patch, please see https://stackoverflow.com/a/37406982]

url:    https://github.com/0day-ci/linux/commits/Dhananjay-Kangude/Add-EDAC-support-for-Cadence-ddr-controller/20200225-185633
base:   https://git.kernel.org/pub/scm/linux/kernel/git/ras/ras.git edac-for-next
config: i386-allyesconfig (attached as .config)
compiler: gcc-7 (Debian 7.5.0-5) 7.5.0
reproduce:
        # save the attached .config to linux build tree
        make ARCH=i386 

If you fix the issue, kindly add following tag
Reported-by: kbuild test robot <lkp@intel.com>

All error/warnings (new ones prefixed by >>):

   drivers//edac/cadence_edac.c: In function 'init_mem_layout':
>> drivers//edac/cadence_edac.c:179:9: error: implicit declaration of function 'EDAC_DIMM_PTR' [-Werror=implicit-function-declaration]
     dimm = EDAC_DIMM_PTR(mci->layers, mci->dimms, mci->n_layers, 0, 0, 0);
            ^~~~~~~~~~~~~
>> drivers//edac/cadence_edac.c:179:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
     dimm = EDAC_DIMM_PTR(mci->layers, mci->dimms, mci->n_layers, 0, 0, 0);
          ^
   drivers//edac/cadence_edac.c: In function 'cdns_edac_mc_probe':
   drivers//edac/cadence_edac.c:476:17: warning: unused variable 'root' [-Wunused-variable]
     struct dentry *root;
                    ^~~~
   cc1: some warnings being treated as errors

vim +/EDAC_DIMM_PTR +179 drivers//edac/cadence_edac.c

   159	
   160	/**
   161	 * init_mem_layout -  Set address Map as per the mc design.
   162	 * @mci:   memory controller information.
   163	 *
   164	 * Set Address Map as per mc instance .
   165	 *
   166	 * Return: none.
   167	 */
   168	static void init_mem_layout(struct mem_ctl_info *mci)
   169	{
   170		struct cdns_edac_priv_data *priv = mci->pvt_info;
   171		struct csrow_info *csi;
   172		struct dimm_info *dimm;
   173		struct sysinfo inf;
   174		enum mem_type mtype;
   175		u32 val, width;
   176		u32 size, row;
   177		u8 j;
   178	
 > 179		dimm = EDAC_DIMM_PTR(mci->layers, mci->dimms, mci->n_layers, 0, 0, 0);
   180	
   181		si_meminfo(&inf);
   182		for (row = 0; row < mci->nr_csrows; row++) {
   183			csi = mci->csrows[row];
   184			size = inf.totalram * inf.mem_unit;
   185	
   186			for (j = 0; j < csi->nr_channels; j++) {
   187				dimm            = csi->channels[j]->dimm;
   188				dimm->edac_mode = EDAC_FLAG_SECDED;
   189				/* Get memory type by reading hw registers*/
   190				val = readl(priv->reg + DDR_CTL_MEM_TYPE_REG);
   191				mtype = val & ECC_CTL_MTYPE_MASK;
   192	
   193				if (mtype == MEM_TYPE_DDR4)
   194					dimm->mtype = MEM_DDR4;
   195				else
   196					dimm->mtype = MEM_EMPTY;
   197	
   198				/*Get EDAC devtype width for the current mc*/
   199				width = (readl(priv->reg + DDR_CTL_MEM_WIDTH_REG) &
   200					       CTL_MEM_MAX_WIDTH_MASK);
   201				switch (width) {
   202				case WDTH_16:
   203					dimm->dtype  = DEV_X2;
   204					break;
   205				case WDTH_32:
   206					dimm->dtype  = DEV_X4;
   207					break;
   208				case WDTH_64:
   209					dimm->dtype  = DEV_X8;
   210					break;
   211				default:
   212					dimm->dtype = DEV_UNKNOWN;
   213				}
   214	
   215				dimm->nr_pages  = (size >> PAGE_SHIFT) /
   216						   csi->nr_channels;
   217				dimm->grain     = CDNS_EDAC_ERR_GRAIN;
   218			}
   219		}
   220	}
   221	

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 71478 bytes --]

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [RFC PATCH] EDAC/Cadence: data_synd[] can be static
  2020-02-25  9:38 ` [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller Dhananjay Kangude
  2020-02-25 22:04   ` kbuild test robot
@ 2020-02-26  2:11   ` kbuild test robot
  2020-02-26  3:26   ` [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller kbuild test robot
  2 siblings, 0 replies; 7+ messages in thread
From: kbuild test robot @ 2020-02-26  2:11 UTC (permalink / raw)
  To: Dhananjay Kangude; +Cc: kbuild-all, linux-edac


Fixes: 201447a5db9b ("EDAC/Cadence:Add EDAC driver for cadence memory controller")
Signed-off-by: kbuild test robot <lkp@intel.com>
---
 cadence_edac.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/edac/cadence_edac.c b/drivers/edac/cadence_edac.c
index 3887db5665eee..17aa656a740ee 100644
--- a/drivers/edac/cadence_edac.c
+++ b/drivers/edac/cadence_edac.c
@@ -121,7 +121,7 @@
 /* Syndrome values */
 #define ECC_DOUBLE_MULTI_ERR_SYND	0x03
 
-char data_synd[] = {
+static char data_synd[] = {
 			0xf4, 0xf1, 0xec, 0xea, 0xe9, 0xe6, 0xe5, 0xe3,
 			0xdc, 0xda, 0xd9, 0xd6, 0xd5, 0xd3, 0xce, 0xcb,
 			0xb5, 0xb0, 0xad, 0xab, 0xa8, 0xa7, 0xa4, 0xa2,
@@ -132,7 +132,7 @@ char data_synd[] = {
 			0x1c, 0x1a, 0x19, 0x16, 0x15, 0x13, 0x0e, 0x0b
 		  };
 
-char check_synd[] = {0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80};
+static char check_synd[] = {0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80};
 
 /**
  * struct cdns_platform_data -  cadence platform data structure.

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller
  2020-02-25  9:38 ` [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller Dhananjay Kangude
  2020-02-25 22:04   ` kbuild test robot
  2020-02-26  2:11   ` [RFC PATCH] EDAC/Cadence: data_synd[] can be static kbuild test robot
@ 2020-02-26  3:26   ` kbuild test robot
  2 siblings, 0 replies; 7+ messages in thread
From: kbuild test robot @ 2020-02-26  3:26 UTC (permalink / raw)
  To: Dhananjay Kangude; +Cc: kbuild-all, clang-built-linux, linux-edac

[-- Attachment #1: Type: text/plain, Size: 3824 bytes --]

Hi Dhananjay,

Thank you for the patch! Yet something to improve:

[auto build test ERROR on ras/edac-for-next]
[also build test ERROR on next-20200225]
[cannot apply to v5.6-rc3]
[if your patch is applied to the wrong git tree, please drop us a note to help
improve the system. BTW, we also suggest to use '--base' option to specify the
base tree in git format-patch, please see https://stackoverflow.com/a/37406982]

url:    https://github.com/0day-ci/linux/commits/Dhananjay-Kangude/Add-EDAC-support-for-Cadence-ddr-controller/20200225-185633
base:   https://git.kernel.org/pub/scm/linux/kernel/git/ras/ras.git edac-for-next
config: arm64-allyesconfig (attached as .config)
compiler: clang version 11.0.0 (git://gitmirror/llvm_project 7f9f027c62623bff79730cd30d1a8a534e2ddb06)
reproduce:
        # FIXME the reproduce steps for clang is not ready yet

If you fix the issue, kindly add following tag
Reported-by: kbuild test robot <lkp@intel.com>

All error/warnings (new ones prefixed by >>):

>> drivers/edac/cadence_edac.c:179:9: error: implicit declaration of function 'EDAC_DIMM_PTR' [-Werror,-Wimplicit-function-declaration]
           dimm = EDAC_DIMM_PTR(mci->layers, mci->dimms, mci->n_layers, 0, 0, 0);
                  ^
>> drivers/edac/cadence_edac.c:179:7: warning: incompatible integer to pointer conversion assigning to 'struct dimm_info *' from 'int' [-Wint-conversion]
           dimm = EDAC_DIMM_PTR(mci->layers, mci->dimms, mci->n_layers, 0, 0, 0);
                ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
   drivers/edac/cadence_edac.c:476:17: warning: unused variable 'root' [-Wunused-variable]
           struct dentry *root;
                          ^
   2 warnings and 1 error generated.

vim +/EDAC_DIMM_PTR +179 drivers/edac/cadence_edac.c

   159	
   160	/**
   161	 * init_mem_layout -  Set address Map as per the mc design.
   162	 * @mci:   memory controller information.
   163	 *
   164	 * Set Address Map as per mc instance .
   165	 *
   166	 * Return: none.
   167	 */
   168	static void init_mem_layout(struct mem_ctl_info *mci)
   169	{
   170		struct cdns_edac_priv_data *priv = mci->pvt_info;
   171		struct csrow_info *csi;
   172		struct dimm_info *dimm;
   173		struct sysinfo inf;
   174		enum mem_type mtype;
   175		u32 val, width;
   176		u32 size, row;
   177		u8 j;
   178	
 > 179		dimm = EDAC_DIMM_PTR(mci->layers, mci->dimms, mci->n_layers, 0, 0, 0);
   180	
   181		si_meminfo(&inf);
   182		for (row = 0; row < mci->nr_csrows; row++) {
   183			csi = mci->csrows[row];
   184			size = inf.totalram * inf.mem_unit;
   185	
   186			for (j = 0; j < csi->nr_channels; j++) {
   187				dimm            = csi->channels[j]->dimm;
   188				dimm->edac_mode = EDAC_FLAG_SECDED;
   189				/* Get memory type by reading hw registers*/
   190				val = readl(priv->reg + DDR_CTL_MEM_TYPE_REG);
   191				mtype = val & ECC_CTL_MTYPE_MASK;
   192	
   193				if (mtype == MEM_TYPE_DDR4)
   194					dimm->mtype = MEM_DDR4;
   195				else
   196					dimm->mtype = MEM_EMPTY;
   197	
   198				/*Get EDAC devtype width for the current mc*/
   199				width = (readl(priv->reg + DDR_CTL_MEM_WIDTH_REG) &
   200					       CTL_MEM_MAX_WIDTH_MASK);
   201				switch (width) {
   202				case WDTH_16:
   203					dimm->dtype  = DEV_X2;
   204					break;
   205				case WDTH_32:
   206					dimm->dtype  = DEV_X4;
   207					break;
   208				case WDTH_64:
   209					dimm->dtype  = DEV_X8;
   210					break;
   211				default:
   212					dimm->dtype = DEV_UNKNOWN;
   213				}
   214	
   215				dimm->nr_pages  = (size >> PAGE_SHIFT) /
   216						   csi->nr_channels;
   217				dimm->grain     = CDNS_EDAC_ERR_GRAIN;
   218			}
   219		}
   220	}
   221	

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 70475 bytes --]

^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, back to index

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-02-25  9:38 [PATCH 0/2] Add EDAC support for Cadence ddr controller Dhananjay Kangude
2020-02-25  9:38 ` [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller Dhananjay Kangude
2020-02-25 22:04   ` kbuild test robot
2020-02-26  2:11   ` [RFC PATCH] EDAC/Cadence: data_synd[] can be static kbuild test robot
2020-02-26  3:26   ` [PATCH 1/2] EDAC/Cadence:Add EDAC driver for cadence memory controller kbuild test robot
2020-02-25  9:38 ` [PATCH 2/2] dt-bindings: edac: Add cadence ddr mc support Dhananjay Kangude
2020-02-25 16:58   ` Rob Herring

Linux-EDAC Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-edac/0 linux-edac/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-edac linux-edac/ https://lore.kernel.org/linux-edac \
		linux-edac@vger.kernel.org
	public-inbox-index linux-edac

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-edac


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git