Re: [PATCH v3 1/2] dt-bindings: edac: arm-dmc520.txt

Re: [PATCH v3 1/2] dt-bindings: edac: arm-dmc520.txt

[James Morse]

Hi Lei,

On 16/05/2019 03:35, Lei Wang wrote:
> From: Lei Wang <leiwang_git@outlook.com>
> 
> This is the device tree bindings for new EDAC driver dmc520_edac.c.

> diff --git a/Documentation/devicetree/bindings/edac/arm-dmc520.txt b/Documentation/devicetree/bindings/edac/arm-dmc520.txt
> new file mode 100644
> index 0000000..71e7aa3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/edac/arm-dmc520.txt
> @@ -0,0 +1,26 @@
> +* ARM DMC-520 EDAC node
> +

> +Required properties:
> +- compatible		: "brcm,dmc-520", "arm,dmc-520".
> +- reg			: Address range of the DMC-520 registers.
> +- interrupts		: DMC-520 interrupt numbers. The example below specifies
> +			  two interrupt lines for dram_ecc_errc_int and
> +			  dram_ecc_errd_int.
> +- interrupt-config	: This is an array of interrupt masks. For each of the
> +			  above interrupt line, add one interrupt mask element to
> +			  it. That is, there is a 1:1 mapping from each interrupt
> +			  line to an interrupt mask. An interrupt mask can represent
> +			  multiple interrupts being enabled.

Cunning!


> +			  Refer to interrupt_control
> +			  register in DMC-520 TRM for interrupt mapping. In the example
> +			  below, the interrupt configuration enables dram_ecc_errc_int
> +			  and dram_ecc_errd_int. And each interrupt is connected to
> +			  a separate interrupt line.
> +
> +Example:
> +
> +dmc0: dmc@200000 {
> +	compatible = "brcm,dmc-520", "arm,dmc-520";
> +	reg = <0x200000 0x80000>;
> +	interrupts = <0x0 0x349 0x4>, <0x0 0x34B 0x4>;
> +	interrupt-config = <0x4>, <0x8>;
> +};
> 

For what its worth:
Acked-by: James Morse <james.morse@arm.com>


Thanks,

James

Re: [PATCH v3 1/2] dt-bindings: edac: arm-dmc520.txt

[Mark Rutland]

On Thu, May 16, 2019 at 02:35:47AM +0000, Lei Wang wrote:
> From: Lei Wang <leiwang_git@outlook.com>
> 
> This is the device tree bindings for new EDAC driver dmc520_edac.c.
> 
> Signed-off-by: Lei Wang <leiwang_git@outlook.com>
> ---
>  .../devicetree/bindings/edac/arm-dmc520.txt        | 26 ++++++++++++++++++++++
>  1 file changed, 26 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/edac/arm-dmc520.txt
> 
> diff --git a/Documentation/devicetree/bindings/edac/arm-dmc520.txt b/Documentation/devicetree/bindings/edac/arm-dmc520.txt
> new file mode 100644
> index 0000000..71e7aa3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/edac/arm-dmc520.txt
> @@ -0,0 +1,26 @@
> +* ARM DMC-520 EDAC node
> +
> +Required properties:
> +- compatible		: "brcm,dmc-520", "arm,dmc-520".
> +- reg			: Address range of the DMC-520 registers.
> +- interrupts		: DMC-520 interrupt numbers. The example below specifies
> +			  two interrupt lines for dram_ecc_errc_int and
> +			  dram_ecc_errd_int.
> +- interrupt-config	: This is an array of interrupt masks. For each of the
> +			  above interrupt line, add one interrupt mask element to
> +			  it. That is, there is a 1:1 mapping from each interrupt
> +			  line to an interrupt mask. An interrupt mask can represent
> +			  multiple interrupts being enabled. Refer to interrupt_control
> +			  register in DMC-520 TRM for interrupt mapping. In the example
> +			  below, the interrupt configuration enables dram_ecc_errc_int
> +			  and dram_ecc_errd_int. And each interrupt is connected to
> +			  a separate interrupt line.

Generally we use interrupt-names to distinguish interrupts.

Do you really have arbitary subsets of lines muxed together?

Thanks,
Mark.

> +
> +Example:
> +
> +dmc0: dmc@200000 {
> +	compatible = "brcm,dmc-520", "arm,dmc-520";
> +	reg = <0x200000 0x80000>;
> +	interrupts = <0x0 0x349 0x4>, <0x0 0x34B 0x4>;
> +	interrupt-config = <0x4>, <0x8>;
> +};
> -- 
> 2.7.4
> 

RE: [PATCH v3 1/2] dt-bindings: edac: arm-dmc520.txt

[Lei Wang (BSP)]

(+Rui/Hang/Sasha)

Hi Mark, please see inline with "[Lei]" tag. Thanks! -Lei

-----Original Message-----
From: Mark Rutland <mark.rutland@arm.com> 
Sent: Thursday, May 23, 2019 9:59 AM
To: Lei Wang <leiwang_git@outlook.com>
Cc: bp@alien8.de; james.morse@arm.com; robh+dt@kernel.org; devicetree@vger.kernel.org; linux-kernel@vger.kernel.org; linux-edac@vger.kernel.org; Lei Wang (BSP) <Wang.Lei@microsoft.com>
Subject: Re: [PATCH v3 1/2] dt-bindings: edac: arm-dmc520.txt

On Thu, May 16, 2019 at 02:35:47AM +0000, Lei Wang wrote:
> From: Lei Wang <leiwang_git@outlook.com>
> 
> This is the device tree bindings for new EDAC driver dmc520_edac.c.
> 
> Signed-off-by: Lei Wang <leiwang_git@outlook.com>
> ---
>  .../devicetree/bindings/edac/arm-dmc520.txt        | 26 ++++++++++++++++++++++
>  1 file changed, 26 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/edac/arm-dmc520.txt
> 
> diff --git a/Documentation/devicetree/bindings/edac/arm-dmc520.txt b/Documentation/devicetree/bindings/edac/arm-dmc520.txt
> new file mode 100644
> index 0000000..71e7aa3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/edac/arm-dmc520.txt
> @@ -0,0 +1,26 @@
> +* ARM DMC-520 EDAC node
> +
> +Required properties:
> +- compatible		: "brcm,dmc-520", "arm,dmc-520".
> +- reg			: Address range of the DMC-520 registers.
> +- interrupts		: DMC-520 interrupt numbers. The example below specifies
> +			  two interrupt lines for dram_ecc_errc_int and
> +			  dram_ecc_errd_int.
> +- interrupt-config	: This is an array of interrupt masks. For each of the
> +			  above interrupt line, add one interrupt mask element to
> +			  it. That is, there is a 1:1 mapping from each interrupt
> +			  line to an interrupt mask. An interrupt mask can represent
> +			  multiple interrupts being enabled. Refer to interrupt_control
> +			  register in DMC-520 TRM for interrupt mapping. In the example
> +			  below, the interrupt configuration enables dram_ecc_errc_int
> +			  and dram_ecc_errd_int. And each interrupt is connected to
> +			  a separate interrupt line.

Generally we use interrupt-names to distinguish interrupts.

Do you really have arbitary subsets of lines muxed together?

-----------------------------------------------
[Lei] Yes it is possible to mux multiple interrupt sources into one interrupt line for dmc520. For example, in this particular brcm implementation, 

Line 841: source dram_ecc_errc_int
Line 843: source dram_ecc_errd_int
Line 839: source dram_ecc_errc_int and dram_ecc_errd_int

There are two possibilities for implementing ecc counts for ce/ue. And we chose to use the single source line. But it's possible to implement using the combined-source line too. This dt binding can support both by modifying the properties.
-------------------------------------------------

Thanks,
Mark.

> +
> +Example:
> +
> +dmc0: dmc@200000 {
> +	compatible = "brcm,dmc-520", "arm,dmc-520";
> +	reg = <0x200000 0x80000>;
> +	interrupts = <0x0 0x349 0x4>, <0x0 0x34B 0x4>;
> +	interrupt-config = <0x4>, <0x8>;
> +};
> -- 
> 2.7.4
>