[PATCH v8 0/6] Enable Linux guests on Hyper-V on ARM64

[PATCH v8 0/6] Enable Linux guests on Hyper-V on ARM64

[Michael Kelley]

This series enables Linux guests running on Hyper-V on ARM64
hardware. New ARM64-specific code in arch/arm64/hyperv initializes
Hyper-V, including its interrupts and hypercall mechanism.
Existing architecture independent drivers for Hyper-V's VMbus and
synthetic devices just work when built for ARM64. Hyper-V code is
built and included in the image and modules only if CONFIG_HYPERV
is enabled.

The six patches are organized as follows:

1) Add definitions and functions for making Hyper-V hypercalls
   and getting/setting virtual processor registers provided by
   Hyper-V

2) Add architecture specific definitions needed by the
   architecture independent Hyper-V clocksource driver in
   drivers/clocksource/hyperv_timer.c. Update the clocksource
   driver to be initialized on ARM64.

3) Add functions needed by the arch independent VMbus driver
   for reporting a panic to Hyper-V and as stubs for the kexec
   and crash handlers.

4) Add Hyper-V initialization code and utility functions that
   report Hyper-v status.

5) Export screen_info so it may be used by the Hyper-V frame buffer
   driver built as a module. It is already exported for x86,
   powerpc, and alpha architectures.

6) Make CONFIG_HYPERV selectable on ARM64 in addition to x86/x64.

Hyper-V on ARM64 runs with a 4 Kbyte page size, but allows guests
with 4K/16K/64K page size. Linux guests with this ARM64 enablement
code work with all three supported ARM64 page sizes.

The Hyper-V vPCI driver at drivers/pci/host/pci-hyperv.c has
x86/x64-specific code and is not being built for ARM64. Fixing
this driver to enable vPCI devices on ARM64 will be done later.

In a few cases, terminology from the x86/x64 world has been carried
over into the ARM64 code ("MSR", "TSC").  Hyper-V still uses the
x86/x64 terminology and has not replaced it with something more
generic, so the code uses the Hyper-V terminology.  This will be
fixed when Hyper-V updates the usage in the TLFS.

This patch set is based on the 5.11.0 code tree, plus this patch series
https://lore.kernel.org/lkml/1611779025-21503-1-git-send-email-mikelley@microsoft.com/
that refactors the boundary between arch independent and arch
dependent code for Hyper-V.

Changes in v8:
* Removed a fair amount of code based on refactoring the boundary between
  arch independent and arch dependent code for Hyper-V, per comments
  from Arnd Bergmann. The removed code was either duplicated on
  the x86 side, or has been folded into architecture independent
  code as not really being architecture dependent.
* Added config dependency on !CONFIG_CPU_BIG_ENDIAN [Arnd Bergmann]
* Reworked the approach to Hyper-V initialization. The functionality
  is the same, but is now structured like the Xen code with an early
  init function called in setup_arch() and an early initcall to
  finish the initialization. [Arnd Bergmann]

Changes in v7:
* Separately upstreamed split of hyperv-tlfs.h into arch dependent
  and independent versions.  In this patch set, update the ARM64
  hyperv-tlfs.h to include architecture independent definitions.
  This approach eliminates a lot of lines of otherwise duplicated
  code on the ARM64 side.
* Break ARM64 mshyperv.h into smaller pieces. Have an initial
  baseline, and add code along with patches for a particular
  functional area. [Marc Zyngier]
* In mshyperv.h, use static inline functions instead of #defines
  where possible. [Arnd Bergmann]
* Use VMbus INTID obtained from ACPI DSDT instead of hardcoding.
  The STIMER INTID is still hardcoded because it is needed
  before Linux has initialized the ACPI subsystem, so it can't
  be obtained from the DSDT.  Wedging it into the GTDT seems
  dubious, so was not done. [Marc Zyngier]
* Update Hyper-V page size allocation functions to use
  alloc_page() if PAGE_SIZE == HV_HYP_PAGE_SIZE [Arnd
  Bergmann]
* Various other minor changes based on feedback and to rebase
  to latest linux-next [Marc Zyngier and Arnd Bergmann]

Changes in v6:
* Use SMCCC hypercall interface instead of direct invocation
  of HVC instruction and the Hyper-V hypercall interface
  [Marc Zyngier]
* Reimplemented functions to alloc/free Hyper-V size pages
  using kmalloc/kfree since kmalloc now guarantees alignment of
  power of 2 size allocations [Marc Zyngier]
* Export screen_info in arm64 architecture so it can be used
  by the Hyper-V buffer driver built as a module
* Renamed source file arch/arm64/hyperv/hv_init.c to hv_core.c
  to better reflect its content
* Fixed the bit position of certain feature flags presented by
  Hyper-V to the guest.  The bit positions on ARM64 don't match
  the position on x86 like originally thought.
* Minor fixups to rebase to 5.6-rc5 linux-next

Changes in v5:
* Minor fixups to rebase to 5.4-rc1 linux-next

Changes in v4:
* Moved clock-related code into an architecture independent
  Hyper-V clocksource driver that is already upstream. Clock
  related code is removed from this patch set except for the
  ARM64 specific interrupt handler. [Marc Zyngier]
* Separately upstreamed the split of mshyperv.h into arch independent
  and arch dependent portions. The arch independent portion has been
  removed from this patch set.
* Divided patch #2 of the series into multiple smaller patches
  [Marc Zyngier]
* Changed a dozen or so smaller things based on feedback
  [Marc Zyngier, Will Deacon]
* Added functions to alloc/free Hyper-V size pages for use by
  drivers for Hyper-V synthetic devices when updated to not assume
  guest page size and Hyper-v page size are the same

Changes in v3:
* Added initialization of hv_vp_index array like was recently
  added on x86 branch [KY Srinivasan]
* Changed Hyper-V ARM64 register symbols to be all uppercase 
  instead of mixed case [KY Srinivasan]
* Separated mshyperv.h into two files, one architecture
  independent and one architecture dependent. After this code
  is upstream, will make changes to the x86 code to use the
  architecture independent file and remove duplication. And
  once we have a multi-architecture Hyper-V TLFS, will do a
  separate patch to split hyperv-tlfs.h in the same way.
  [KY Srinivasan]
* Minor tweaks to rebase to latest linux-next code

Changes in v2:
* Removed patch to implement slow_virt_to_phys() on ARM64.
  Use of slow_virt_to_phys() in arch independent Hyper-V
  drivers has been eliminated by commit 6ba34171bcbd
  ("Drivers: hv: vmbus: Remove use of slow_virt_to_phys()")
* Minor tweaks to rebase to latest linux-next code

Michael Kelley (6):
  arm64: hyperv: Add Hyper-V hypercall and register access utilities
  arm64: hyperv: Add Hyper-V clocksource/clockevent support
  arm64: hyperv: Add kexec and panic handlers
  arm64: hyperv: Initialize hypervisor on boot
  arm64: efi: Export screen_info
  Drivers: hv: Enable Hyper-V code to be built on ARM64

 MAINTAINERS                          |   3 +
 arch/arm64/Kbuild                    |   1 +
 arch/arm64/hyperv/Makefile           |   2 +
 arch/arm64/hyperv/hv_core.c          | 220 +++++++++++++++++++++++++++++++++++
 arch/arm64/hyperv/mshyperv.c         | 194 ++++++++++++++++++++++++++++++
 arch/arm64/include/asm/hyperv-tlfs.h |  69 +++++++++++
 arch/arm64/include/asm/mshyperv.h    |  73 ++++++++++++
 arch/arm64/kernel/efi.c              |   1 +
 arch/arm64/kernel/setup.c            |   4 +
 drivers/clocksource/hyperv_timer.c   |  14 +++
 drivers/hv/Kconfig                   |   3 +-
 11 files changed, 583 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/hyperv/Makefile
 create mode 100644 arch/arm64/hyperv/hv_core.c
 create mode 100644 arch/arm64/hyperv/mshyperv.c
 create mode 100644 arch/arm64/include/asm/hyperv-tlfs.h
 create mode 100644 arch/arm64/include/asm/mshyperv.h

-- 
1.8.3.1

[PATCH v8 1/6] arm64: hyperv: Add Hyper-V hypercall and register access utilities

[Michael Kelley]

hyperv-tlfs.h defines Hyper-V interfaces from the Hyper-V Top Level
Functional Spec (TLFS), and #includes the architecture-independent
part of hyperv-tlfs.h in include/asm-generic.  The published TLFS
is distinctly oriented to x86/x64, so the ARM64-specific
hyperv-tlfs.h includes information for ARM64 that is not yet formally
published. The TLFS is available here:

  docs.microsoft.com/en-us/virtualization/hyper-v-on-windows/reference/tlfs

mshyperv.h defines Linux-specific structures and routines for
interacting with Hyper-V on ARM64, and #includes the architecture-
independent part of mshyperv.h in include/asm-generic.

Use these definitions to provide utility functions to make
Hyper-V hypercalls and to get and set Hyper-V provided
registers associated with a virtual processor.

Signed-off-by: Michael Kelley <mikelley@microsoft.com>
---
 MAINTAINERS                          |   3 +
 arch/arm64/Kbuild                    |   1 +
 arch/arm64/hyperv/Makefile           |   2 +
 arch/arm64/hyperv/hv_core.c          | 167 +++++++++++++++++++++++++++++++++++
 arch/arm64/include/asm/hyperv-tlfs.h |  69 +++++++++++++++
 arch/arm64/include/asm/mshyperv.h    |  55 ++++++++++++
 6 files changed, 297 insertions(+)
 create mode 100644 arch/arm64/hyperv/Makefile
 create mode 100644 arch/arm64/hyperv/hv_core.c
 create mode 100644 arch/arm64/include/asm/hyperv-tlfs.h
 create mode 100644 arch/arm64/include/asm/mshyperv.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 546aa66..0a22f3a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8235,6 +8235,9 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux.git
 F:	Documentation/ABI/stable/sysfs-bus-vmbus
 F:	Documentation/ABI/testing/debugfs-hyperv
 F:	Documentation/networking/device_drivers/ethernet/microsoft/netvsc.rst
+F:	arch/arm64/hyperv
+F:	arch/arm64/include/asm/hyperv-tlfs.h
+F:	arch/arm64/include/asm/mshyperv.h
 F:	arch/x86/hyperv
 F:	arch/x86/include/asm/hyperv-tlfs.h
 F:	arch/x86/include/asm/mshyperv.h
diff --git a/arch/arm64/Kbuild b/arch/arm64/Kbuild
index d646582..7a37608 100644
--- a/arch/arm64/Kbuild
+++ b/arch/arm64/Kbuild
@@ -3,4 +3,5 @@ obj-y			+= kernel/ mm/
 obj-$(CONFIG_NET)	+= net/
 obj-$(CONFIG_KVM)	+= kvm/
 obj-$(CONFIG_XEN)	+= xen/
+obj-$(subst m,y,$(CONFIG_HYPERV))	+= hyperv/
 obj-$(CONFIG_CRYPTO)	+= crypto/
diff --git a/arch/arm64/hyperv/Makefile b/arch/arm64/hyperv/Makefile
new file mode 100644
index 0000000..1697d30
--- /dev/null
+++ b/arch/arm64/hyperv/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-y		:= hv_core.o
diff --git a/arch/arm64/hyperv/hv_core.c b/arch/arm64/hyperv/hv_core.c
new file mode 100644
index 0000000..9a37124
--- /dev/null
+++ b/arch/arm64/hyperv/hv_core.c
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/*
+ * Low level utility routines for interacting with Hyper-V.
+ *
+ * Copyright (C) 2021, Microsoft, Inc.
+ *
+ * Author : Michael Kelley <mikelley@microsoft.com>
+ */
+
+
+#include <linux/types.h>
+#include <linux/log2.h>
+#include <linux/export.h>
+#include <linux/mm.h>
+#include <linux/slab.h>
+#include <linux/hyperv.h>
+#include <linux/arm-smccc.h>
+#include <linux/vmalloc.h>
+#include <linux/module.h>
+#include <asm-generic/bug.h>
+#include <asm/hyperv-tlfs.h>
+#include <asm/mshyperv.h>
+
+/*
+ * hv_do_hypercall- Invoke the specified hypercall
+ */
+u64 hv_do_hypercall(u64 control, void *input, void *output)
+{
+	u64 input_address;
+	u64 output_address;
+	struct arm_smccc_res res;
+
+	input_address = input ? virt_to_phys(input) : 0;
+	output_address = output ? virt_to_phys(output) : 0;
+
+	arm_smccc_1_1_hvc(HV_FUNC_ID, control,
+			  input_address, output_address, &res);
+	return res.a0;
+}
+EXPORT_SYMBOL_GPL(hv_do_hypercall);
+
+/*
+ * hv_do_fast_hypercall8 -- Invoke the specified hypercall
+ * with arguments in registers instead of physical memory.
+ * Avoids the overhead of virt_to_phys for simple hypercalls.
+ */
+
+u64 hv_do_fast_hypercall8(u16 code, u64 input)
+{
+	u64 control;
+	struct arm_smccc_res res;
+
+	control = (u64)code | HV_HYPERCALL_FAST_BIT;
+
+	arm_smccc_1_1_hvc(HV_FUNC_ID, control, input, &res);
+	return res.a0;
+}
+EXPORT_SYMBOL_GPL(hv_do_fast_hypercall8);
+
+
+/*
+ * Set a single VP register to a 64-bit value.
+ */
+void hv_set_vpreg(u32 msr, u64 value)
+{
+	struct arm_smccc_res res;
+
+	arm_smccc_1_1_hvc(
+		HV_FUNC_ID,
+		HVCALL_SET_VP_REGISTERS | HV_HYPERCALL_FAST_BIT |
+			HV_HYPERCALL_REP_COMP_1,
+		HV_PARTITION_ID_SELF,
+		HV_VP_INDEX_SELF,
+		msr,
+		0,
+		value,
+		0,
+		&res);
+
+	/*
+	 * Something is fundamentally broken in the hypervisor if
+	 * setting a VP register fails. There's really no way to
+	 * continue as a guest VM, so panic.
+	 */
+	BUG_ON((res.a0 & HV_HYPERCALL_RESULT_MASK) != HV_STATUS_SUCCESS);
+}
+EXPORT_SYMBOL_GPL(hv_set_vpreg);
+
+/*
+ * Get the value of a single VP register.  One version
+ * returns just 64 bits and another returns the full 128 bits.
+ * The two versions are separate to avoid complicating the
+ * calling sequence for the more frequently used 64 bit version.
+ */
+
+void __hv_get_vpreg_128(u32 msr,
+			struct hv_get_vp_registers_input  *input,
+			struct hv_get_vp_registers_output *res)
+{
+	u64	status;
+
+	input->header.partitionid = HV_PARTITION_ID_SELF;
+	input->header.vpindex = HV_VP_INDEX_SELF;
+	input->header.inputvtl = 0;
+	input->element[0].name0 = msr;
+	input->element[0].name1 = 0;
+
+
+	status = hv_do_hypercall(
+		HVCALL_GET_VP_REGISTERS | HV_HYPERCALL_REP_COMP_1,
+		input, res);
+
+	/*
+	 * Something is fundamentally broken in the hypervisor if
+	 * getting a VP register fails. There's really no way to
+	 * continue as a guest VM, so panic.
+	 */
+	BUG_ON((status & HV_HYPERCALL_RESULT_MASK) != HV_STATUS_SUCCESS);
+}
+
+u64 hv_get_vpreg(u32 msr)
+{
+	struct hv_get_vp_registers_input	*input;
+	struct hv_get_vp_registers_output	*output;
+	u64					result;
+
+	/*
+	 * Allocate a power of 2 size so alignment to that size is
+	 * guaranteed, since the hypercall input and output areas
+	 * must not cross a page boundary.
+	 */
+	input = kzalloc(roundup_pow_of_two(sizeof(input->header) +
+				sizeof(input->element[0])), GFP_ATOMIC);
+	output = kmalloc(roundup_pow_of_two(sizeof(*output)), GFP_ATOMIC);
+
+	__hv_get_vpreg_128(msr, input, output);
+
+	result = output->as64.low;
+	kfree(input);
+	kfree(output);
+	return result;
+}
+EXPORT_SYMBOL_GPL(hv_get_vpreg);
+
+void hv_get_vpreg_128(u32 msr, struct hv_get_vp_registers_output *res)
+{
+	struct hv_get_vp_registers_input	*input;
+	struct hv_get_vp_registers_output	*output;
+
+	/*
+	 * Allocate a power of 2 size so alignment to that size is
+	 * guaranteed, since the hypercall input and output areas
+	 * must not cross a page boundary.
+	 */
+	input = kzalloc(roundup_pow_of_two(sizeof(input->header) +
+				sizeof(input->element[0])), GFP_ATOMIC);
+	output = kmalloc(roundup_pow_of_two(sizeof(*output)), GFP_ATOMIC);
+
+	__hv_get_vpreg_128(msr, input, output);
+
+	res->as64.low = output->as64.low;
+	res->as64.high = output->as64.high;
+	kfree(input);
+	kfree(output);
+}
+EXPORT_SYMBOL_GPL(hv_get_vpreg_128);
diff --git a/arch/arm64/include/asm/hyperv-tlfs.h b/arch/arm64/include/asm/hyperv-tlfs.h
new file mode 100644
index 0000000..4d964a7
--- /dev/null
+++ b/arch/arm64/include/asm/hyperv-tlfs.h
@@ -0,0 +1,69 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+/*
+ * This file contains definitions from the Hyper-V Hypervisor Top-Level
+ * Functional Specification (TLFS):
+ * https://docs.microsoft.com/en-us/virtualization/hyper-v-on-windows/reference/tlfs
+ *
+ * Copyright (C) 2021, Microsoft, Inc.
+ *
+ * Author : Michael Kelley <mikelley@microsoft.com>
+ */
+
+#ifndef _ASM_HYPERV_TLFS_H
+#define _ASM_HYPERV_TLFS_H
+
+#include <linux/types.h>
+
+/*
+ * All data structures defined in the TLFS that are shared between Hyper-V
+ * and a guest VM use Little Endian byte ordering.  This matches the default
+ * byte ordering of Linux running on ARM64, so no special handling is required.
+ */
+
+/*
+ * These Hyper-V registers provide information equivalent to the CPUID
+ * instruction on x86/x64.
+ */
+#define HV_REGISTER_HYPERVISOR_VERSION		0x00000100 /*CPUID 0x40000002 */
+#define HV_REGISTER_FEATURES			0x00000200 /*CPUID 0x40000003 */
+#define HV_REGISTER_ENLIGHTENMENTS		0x00000201 /*CPUID 0x40000004 */
+
+/*
+ * Group C Features. See the asm-generic version of hyperv-tlfs.h
+ * for a description of Feature Groups.
+ */
+
+/* Crash MSRs available */
+#define HV_FEATURE_GUEST_CRASH_MSR_AVAILABLE	BIT(8)
+
+/* STIMER direct mode is available */
+#define HV_STIMER_DIRECT_MODE_AVAILABLE		BIT(13)
+
+/*
+ * Synthetic register definitions equivalent to MSRs on x86/x64
+ */
+#define HV_REGISTER_CRASH_P0		0x00000210
+#define HV_REGISTER_CRASH_P1		0x00000211
+#define HV_REGISTER_CRASH_P2		0x00000212
+#define HV_REGISTER_CRASH_P3		0x00000213
+#define HV_REGISTER_CRASH_P4		0x00000214
+#define HV_REGISTER_CRASH_CTL		0x00000215
+
+#define HV_REGISTER_GUEST_OSID		0x00090002
+#define HV_REGISTER_VP_INDEX		0x00090003
+#define HV_REGISTER_TIME_REF_COUNT	0x00090004
+#define HV_REGISTER_REFERENCE_TSC	0x00090017
+
+#define HV_REGISTER_SINT0		0x000A0000
+#define HV_REGISTER_SCONTROL		0x000A0010
+#define HV_REGISTER_SIEFP		0x000A0012
+#define HV_REGISTER_SIMP		0x000A0013
+#define HV_REGISTER_EOM			0x000A0014
+
+#define HV_REGISTER_STIMER0_CONFIG	0x000B0000
+#define HV_REGISTER_STIMER0_COUNT	0x000B0001
+
+#include <asm-generic/hyperv-tlfs.h>
+
+#endif
diff --git a/arch/arm64/include/asm/mshyperv.h b/arch/arm64/include/asm/mshyperv.h
new file mode 100644
index 0000000..44ee012
--- /dev/null
+++ b/arch/arm64/include/asm/mshyperv.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+/*
+ * Linux-specific definitions for managing interactions with Microsoft's
+ * Hyper-V hypervisor. The definitions in this file are specific to
+ * the ARM64 architecture.  See include/asm-generic/mshyperv.h for
+ * definitions are that architecture independent.
+ *
+ * Definitions that are specified in the Hyper-V Top Level Functional
+ * Spec (TLFS) should not go in this file, but should instead go in
+ * hyperv-tlfs.h.
+ *
+ * Copyright (C) 2021, Microsoft, Inc.
+ *
+ * Author : Michael Kelley <mikelley@microsoft.com>
+ */
+
+#ifndef _ASM_MSHYPERV_H
+#define _ASM_MSHYPERV_H
+
+#include <linux/types.h>
+#include <linux/arm-smccc.h>
+#include <asm/hyperv-tlfs.h>
+
+/*
+ * Declare calls to get and set Hyper-V VP register values on ARM64, which
+ * requires a hypercall.
+ */
+
+extern void hv_set_vpreg(u32 reg, u64 value);
+extern u64 hv_get_vpreg(u32 reg);
+extern void __hv_get_vpreg_128(u32 reg, struct hv_get_vp_registers_input *input,
+					struct hv_get_vp_registers_output *result);
+
+static inline void hv_set_register(unsigned int reg, u64 value)
+{
+	hv_set_vpreg(reg, value);
+}
+
+static inline u64 hv_get_register(unsigned int reg)
+{
+	return hv_get_vpreg(reg);
+}
+
+/* SMCCC hypercall parameters */
+#define HV_SMCCC_FUNC_NUMBER	1
+#define HV_FUNC_ID	ARM_SMCCC_CALL_VAL(			\
+				ARM_SMCCC_STD_CALL,		\
+				ARM_SMCCC_SMC_64,		\
+				ARM_SMCCC_OWNER_VENDOR_HYP,	\
+				HV_SMCCC_FUNC_NUMBER)
+
+#include <asm-generic/mshyperv.h>
+
+#endif
-- 
1.8.3.1

[PATCH v8 2/6] arm64: hyperv: Add Hyper-V clocksource/clockevent support

[Michael Kelley]

Add architecture specific definitions and functions needed
by the architecture independent Hyper-V clocksource driver.
Update the Hyper-V clocksource driver to be initialized
on ARM64.

Signed-off-by: Michael Kelley <mikelley@microsoft.com>
---
 arch/arm64/include/asm/mshyperv.h  | 12 ++++++++++++
 drivers/clocksource/hyperv_timer.c | 14 ++++++++++++++
 2 files changed, 26 insertions(+)

diff --git a/arch/arm64/include/asm/mshyperv.h b/arch/arm64/include/asm/mshyperv.h
index 44ee012..d6ff2ee 100644
--- a/arch/arm64/include/asm/mshyperv.h
+++ b/arch/arm64/include/asm/mshyperv.h
@@ -21,6 +21,7 @@
 #include <linux/types.h>
 #include <linux/arm-smccc.h>
 #include <asm/hyperv-tlfs.h>
+#include <clocksource/arm_arch_timer.h>
 
 /*
  * Declare calls to get and set Hyper-V VP register values on ARM64, which
@@ -42,6 +43,17 @@ static inline u64 hv_get_register(unsigned int reg)
 	return hv_get_vpreg(reg);
 }
 
+/* Define the interrupt ID used by STIMER0 Direct Mode interrupts. This
+ * value can't come from ACPI tables because it is needed before the
+ * Linux ACPI subsystem is initialized.
+ */
+#define HYPERV_STIMER0_VECTOR	31
+
+static inline u64 hv_get_raw_timer(void)
+{
+	return arch_timer_read_counter();
+}
+
 /* SMCCC hypercall parameters */
 #define HV_SMCCC_FUNC_NUMBER	1
 #define HV_FUNC_ID	ARM_SMCCC_CALL_VAL(			\
diff --git a/drivers/clocksource/hyperv_timer.c b/drivers/clocksource/hyperv_timer.c
index c553b8c..f8bb5df 100644
--- a/drivers/clocksource/hyperv_timer.c
+++ b/drivers/clocksource/hyperv_timer.c
@@ -567,3 +567,17 @@ void __init hv_init_clocksource(void)
 	hv_setup_sched_clock(read_hv_sched_clock_msr);
 }
 EXPORT_SYMBOL_GPL(hv_init_clocksource);
+
+/* Initialize everything on ARM64 */
+static int __init hyperv_timer_init(struct acpi_table_header *table)
+{
+	if (!hv_is_hyperv_initialized())
+		return -EINVAL;
+
+	hv_init_clocksource();
+	if (hv_stimer_alloc(true))
+		return -EINVAL;
+
+	return 0;
+}
+TIMER_ACPI_DECLARE(hyperv, ACPI_SIG_GTDT, hyperv_timer_init);
-- 
1.8.3.1

[PATCH v8 3/6] arm64: hyperv: Add kexec and panic handlers

[Michael Kelley]

Add function to inform Hyper-V about a guest panic.

Also add functions to set up and remove kexec and panic
handlers, which are currently unused on ARM64 but are
called from architecture independent code in the VMbus
driver.

This code is built only when CONFIG_HYPERV is enabled.

Signed-off-by: Michael Kelley <mikelley@microsoft.com>
---
 arch/arm64/hyperv/Makefile   |  2 +-
 arch/arm64/hyperv/hv_core.c  | 53 +++++++++++++++++++++++++++++++++++++++++++
 arch/arm64/hyperv/mshyperv.c | 54 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 108 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/hyperv/mshyperv.c

diff --git a/arch/arm64/hyperv/Makefile b/arch/arm64/hyperv/Makefile
index 1697d30..87c31c0 100644
--- a/arch/arm64/hyperv/Makefile
+++ b/arch/arm64/hyperv/Makefile
@@ -1,2 +1,2 @@
 # SPDX-License-Identifier: GPL-2.0
-obj-y		:= hv_core.o
+obj-y		:= hv_core.o mshyperv.o
diff --git a/arch/arm64/hyperv/hv_core.c b/arch/arm64/hyperv/hv_core.c
index 9a37124..d4e3808 100644
--- a/arch/arm64/hyperv/hv_core.c
+++ b/arch/arm64/hyperv/hv_core.c
@@ -165,3 +165,56 @@ void hv_get_vpreg_128(u32 msr, struct hv_get_vp_registers_output *res)
 	kfree(output);
 }
 EXPORT_SYMBOL_GPL(hv_get_vpreg_128);
+
+/*
+ * hyperv_report_panic - report a panic to Hyper-V.  This function uses
+ * the older version of the Hyper-V interface that admittedly doesn't
+ * pass enough information to be useful beyond just recording the
+ * occurrence of a panic. The parallel hv_kmsg_dump() uses the
+ * new interface that allows reporting 4 Kbytes of data, which is much
+ * more useful. Hyper-V on ARM64 always supports the newer interface, but
+ * we retain support for the older version because the sysadmin is allowed
+ * to disable the newer version via sysctl in case of information security
+ * concerns about the more verbose version.
+ */
+void hyperv_report_panic(struct pt_regs *regs, long err, bool in_die)
+{
+	static bool panic_reported;
+	u64 guest_id;
+
+	/* Don't report a panic to Hyper-V if we're not going to panic */
+	if (in_die && !panic_on_oops)
+		return;
+
+	/*
+	 * We prefer to report panic on 'die' chain as we have proper
+	 * registers to report, but if we miss it (e.g. on BUG()) we need
+	 * to report it on 'panic'.
+	 *
+	 * Calling code in the 'die' and 'panic' paths ensures that only
+	 * one CPU is running this code, so no atomicity is needed.
+	 */
+	if (panic_reported)
+		return;
+	panic_reported = true;
+
+	guest_id = hv_get_vpreg(HV_REGISTER_GUEST_OSID);
+
+	/*
+	 * Hyper-V provides the ability to store only 5 values.
+	 * Pick the passed in error value, the guest_id, and the PC.
+	 * The first two general registers are added arbitrarily.
+	 */
+	hv_set_vpreg(HV_REGISTER_CRASH_P0, err);
+	hv_set_vpreg(HV_REGISTER_CRASH_P1, guest_id);
+	hv_set_vpreg(HV_REGISTER_CRASH_P2, regs->pc);
+	hv_set_vpreg(HV_REGISTER_CRASH_P3, regs->regs[0]);
+	hv_set_vpreg(HV_REGISTER_CRASH_P4, regs->regs[1]);
+
+	/*
+	 * Let Hyper-V know there is crash data available
+	 */
+	hv_set_vpreg(HV_REGISTER_CRASH_CTL, HV_CRASH_CTL_CRASH_NOTIFY);
+}
+EXPORT_SYMBOL_GPL(hyperv_report_panic);
+
diff --git a/arch/arm64/hyperv/mshyperv.c b/arch/arm64/hyperv/mshyperv.c
new file mode 100644
index 0000000..d202b4c
--- /dev/null
+++ b/arch/arm64/hyperv/mshyperv.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/*
+ * Core routines for interacting with Microsoft's Hyper-V hypervisor.
+ * Includes hypervisor initialization, and handling of crashes and
+ * kexecs through a set of static "handler" variables set by the
+ * architecture independent VMbus driver.
+ *
+ * Copyright (C) 2021, Microsoft, Inc.
+ *
+ * Author : Michael Kelley <mikelley@microsoft.com>
+ */
+
+#include <linux/types.h>
+#include <linux/export.h>
+#include <linux/ptrace.h>
+
+/*
+ * The VMbus handler functions are no-ops on ARM64 because
+ * VMbus interrupts are handled as percpu IRQs.
+ */
+void hv_setup_vmbus_handler(void (*handler)(void))
+{
+}
+EXPORT_SYMBOL_GPL(hv_setup_vmbus_handler);
+
+void hv_remove_vmbus_handler(void)
+{
+}
+EXPORT_SYMBOL_GPL(hv_remove_vmbus_handler);
+
+/*
+ * The kexec and crash handler functions are
+ * currently no-ops on ARM64.
+ */
+void hv_setup_kexec_handler(void (*handler)(void))
+{
+}
+EXPORT_SYMBOL_GPL(hv_setup_kexec_handler);
+
+void hv_remove_kexec_handler(void)
+{
+}
+EXPORT_SYMBOL_GPL(hv_remove_kexec_handler);
+
+void hv_setup_crash_handler(void (*handler)(struct pt_regs *regs))
+{
+}
+EXPORT_SYMBOL_GPL(hv_setup_crash_handler);
+
+void hv_remove_crash_handler(void)
+{
+}
+EXPORT_SYMBOL_GPL(hv_remove_crash_handler);
-- 
1.8.3.1

[PATCH v8 4/6] arm64: hyperv: Initialize hypervisor on boot

[Michael Kelley]

Add ARM64-specific code to initialize the Hyper-V
hypervisor when booting as a guest VM. Provide functions
and data structures indicating hypervisor status that
are needed by VMbus driver.

This code is built only when CONFIG_HYPERV is enabled.

Signed-off-by: Michael Kelley <mikelley@microsoft.com>
---
 arch/arm64/hyperv/mshyperv.c      | 140 ++++++++++++++++++++++++++++++++++++++
 arch/arm64/include/asm/mshyperv.h |   6 ++
 arch/arm64/kernel/setup.c         |   4 ++
 3 files changed, 150 insertions(+)

diff --git a/arch/arm64/hyperv/mshyperv.c b/arch/arm64/hyperv/mshyperv.c
index d202b4c..c72bc66 100644
--- a/arch/arm64/hyperv/mshyperv.c
+++ b/arch/arm64/hyperv/mshyperv.c
@@ -14,6 +14,146 @@
 #include <linux/types.h>
 #include <linux/export.h>
 #include <linux/ptrace.h>
+#include <linux/errno.h>
+#include <linux/acpi.h>
+#include <linux/version.h>
+#include <linux/log2.h>
+#include <asm/mshyperv.h>
+
+static bool	hyperv_initialized;
+
+struct	ms_hyperv_info ms_hyperv __ro_after_init;
+EXPORT_SYMBOL_GPL(ms_hyperv);
+
+u32	*hv_vp_index;
+EXPORT_SYMBOL_GPL(hv_vp_index);
+
+u32	hv_max_vp_index;
+EXPORT_SYMBOL_GPL(hv_max_vp_index);
+
+/*
+ * As hypercall input and output, align to a power of 2 to ensure they
+ * don't cross a page boundary. Initialize the first element of the
+ * variable size array in the input to ensure enough space is allocated.
+ */
+static struct hv_get_vp_registers_input  input __initdata __aligned(
+		roundup_pow_of_two(sizeof(struct hv_get_vp_registers_input) +
+		sizeof(struct input))) = {.element[0].name0 = 1};
+static struct hv_get_vp_registers_output result __initdata __aligned(
+		roundup_pow_of_two(sizeof(struct hv_get_vp_registers_output)));
+
+void __init hyperv_early_init(void)
+{
+	u32	a, b, c, d;
+	u64	guest_id;
+
+	/*
+	 * If we're in a VM on Hyper-V, the ACPI hypervisor_id field will
+	 * have the string "MsHyperV".
+	 */
+	if (strncmp((char *)&acpi_gbl_FADT.hypervisor_id, "MsHyperV", 8))
+		return;
+
+	/* Setup the guest ID */
+	guest_id = generate_guest_id(0, LINUX_VERSION_CODE, 0);
+	hv_set_vpreg(HV_REGISTER_GUEST_OSID, guest_id);
+
+	/* Get the features and hints from Hyper-V */
+	__hv_get_vpreg_128(HV_REGISTER_FEATURES, &input, &result);
+	ms_hyperv.features = result.as32.a;
+	ms_hyperv.misc_features = result.as32.c;
+
+	__hv_get_vpreg_128(HV_REGISTER_ENLIGHTENMENTS, &input, &result);
+	ms_hyperv.hints = result.as32.a;
+
+	pr_info("Hyper-V: Features 0x%x, hints 0x%x, misc 0x%x\n",
+		ms_hyperv.features, ms_hyperv.hints, ms_hyperv.misc_features);
+
+	/*
+	 * If Hyper-V has crash notifications, set crash_kexec_post_notifiers
+	 * so that we will report the panic to Hyper-V before running kdump.
+	 */
+	if (ms_hyperv.misc_features & HV_FEATURE_GUEST_CRASH_MSR_AVAILABLE)
+		crash_kexec_post_notifiers = true;
+
+	/* Get information about the Hyper-V host version */
+	__hv_get_vpreg_128(HV_REGISTER_HYPERVISOR_VERSION, &input, &result);
+	a = result.as32.a;
+	b = result.as32.b;
+	c = result.as32.c;
+	d = result.as32.d;
+	pr_info("Hyper-V: Host Build %d.%d.%d.%d-%d-%d\n",
+		b >> 16, b & 0xFFFF, a,	d & 0xFFFFFF, c, d >> 24);
+
+	hyperv_initialized = true;
+}
+
+static u64 hypercall_output __initdata;
+
+static int __init hyperv_init(void)
+{
+	struct hv_get_vpindex_from_apicid_input *input;
+	u64	status;
+	int	i;
+
+	/*
+	 * Hypercall inputs must not cross a page boundary, so allocate
+	 * power of 2 size, which will be aligned to that size.
+	 */
+	input = kzalloc(roundup_pow_of_two(sizeof(input->header) +
+				sizeof(input->element[0])), GFP_KERNEL);
+	if (!input)
+		return -ENOMEM;
+
+	/* Allocate and initialize percpu VP index array */
+	hv_max_vp_index = num_possible_cpus();
+	hv_vp_index = kmalloc_array(hv_max_vp_index, sizeof(*hv_vp_index),
+				    GFP_KERNEL);
+	if (!hv_vp_index) {
+		kfree(input);
+		return -ENOMEM;
+	}
+
+	input->header.partitionid = HV_PARTITION_ID_SELF;
+	for (i = 0; i < hv_max_vp_index; i++) {
+		input->element[0].mpidr = cpu_logical_map(i);
+		status = hv_do_hypercall(HVCALL_VPINDEX_FROM_APICID |
+				HV_HYPERCALL_REP_COMP_1, input,
+				&hypercall_output);
+		if ((status & HV_HYPERCALL_RESULT_MASK) == HV_STATUS_SUCCESS)
+			hv_vp_index[i] = hypercall_output;
+		else {
+			pr_warn("Hyper-V: No VP index for CPU %d MPIDR %llx status %llx\n",
+				i, cpu_logical_map(i), status);
+			hv_vp_index[i] = VP_INVAL;
+		}
+	}
+
+	kfree(input);
+	return 0;
+}
+
+early_initcall(hyperv_init);
+
+/* This routine is called before kexec/kdump. It does required cleanup. */
+void hyperv_cleanup(void)
+{
+	hv_set_vpreg(HV_REGISTER_GUEST_OSID, 0);
+
+}
+EXPORT_SYMBOL_GPL(hyperv_cleanup);
+
+bool hv_is_hyperv_initialized(void)
+{
+	return hyperv_initialized;
+}
+EXPORT_SYMBOL_GPL(hv_is_hyperv_initialized);
+
+bool hv_is_hibernation_supported(void)
+{
+	return false;
+}
+EXPORT_SYMBOL_GPL(hv_is_hibernation_supported);
 
 /*
  * The VMbus handler functions are no-ops on ARM64 because
diff --git a/arch/arm64/include/asm/mshyperv.h b/arch/arm64/include/asm/mshyperv.h
index d6ff2ee..55a61a8 100644
--- a/arch/arm64/include/asm/mshyperv.h
+++ b/arch/arm64/include/asm/mshyperv.h
@@ -23,6 +23,12 @@
 #include <asm/hyperv-tlfs.h>
 #include <clocksource/arm_arch_timer.h>
 
+#if IS_ENABLED(CONFIG_HYPERV)
+void __init hyperv_early_init(void);
+#else
+static inline void hyperv_early_init(void) {};
+#endif
+
 /*
  * Declare calls to get and set Hyper-V VP register values on ARM64, which
  * requires a hypercall.
diff --git a/arch/arm64/kernel/setup.c b/arch/arm64/kernel/setup.c
index c18aacd..1df8285 100644
--- a/arch/arm64/kernel/setup.c
+++ b/arch/arm64/kernel/setup.c
@@ -49,6 +49,7 @@
 #include <asm/traps.h>
 #include <asm/efi.h>
 #include <asm/xen/hypervisor.h>
+#include <asm/mshyperv.h>
 #include <asm/mmu_context.h>
 
 static int num_standard_resources;
@@ -340,6 +341,9 @@ void __init __no_sanitize_address setup_arch(char **cmdline_p)
 	if (acpi_disabled)
 		unflatten_device_tree();
 
+	/* Do after acpi_boot_table_init() so local FADT is available */
+	hyperv_early_init();
+
 	bootmem_init();
 
 	kasan_init();
-- 
1.8.3.1

[PATCH v8 5/6] arm64: efi: Export screen_info

[Michael Kelley]

The Hyper-V frame buffer driver may be built as a module, and
it needs access to screen_info. So export screen_info.

Signed-off-by: Michael Kelley <mikelley@microsoft.com>
---
 arch/arm64/kernel/efi.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/kernel/efi.c b/arch/arm64/kernel/efi.c
index fa02efb..e1be6c4 100644
--- a/arch/arm64/kernel/efi.c
+++ b/arch/arm64/kernel/efi.c
@@ -55,6 +55,7 @@ static __init pteval_t create_mapping_protection(efi_memory_desc_t *md)
 
 /* we will fill this structure from the stub, so don't put it in .bss */
 struct screen_info screen_info __section(".data");
+EXPORT_SYMBOL(screen_info);
 
 int __init efi_create_mapping(struct mm_struct *mm, efi_memory_desc_t *md)
 {
-- 
1.8.3.1

[PATCH v8 6/6] Drivers: hv: Enable Hyper-V code to be built on ARM64

[Michael Kelley]

Update drivers/hv/Kconfig so CONFIG_HYPERV can be selected on
ARM64, causing the Hyper-V specific code to be built.

Signed-off-by: Michael Kelley <mikelley@microsoft.com>
---
 drivers/hv/Kconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/hv/Kconfig b/drivers/hv/Kconfig
index 79e5356..d492682 100644
--- a/drivers/hv/Kconfig
+++ b/drivers/hv/Kconfig
@@ -4,7 +4,8 @@ menu "Microsoft Hyper-V guest support"
 
 config HYPERV
 	tristate "Microsoft Hyper-V client drivers"
-	depends on X86 && ACPI && X86_LOCAL_APIC && HYPERVISOR_GUEST
+	depends on ACPI && ((X86 && X86_LOCAL_APIC && HYPERVISOR_GUEST) \
+		|| (ARM64 && !CPU_BIG_ENDIAN))
 	select PARAVIRT
 	select X86_HV_CALLBACK_VECTOR
 	help
-- 
1.8.3.1

Re: [PATCH v8 2/6] arm64: hyperv: Add Hyper-V clocksource/clockevent support

[kernel test robot]

[-- Attachment #1: Type: text/plain, Size: 3128 bytes --]

Hi Michael,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on arm64/for-next/core]
[also build test WARNING on tip/timers/core efi/next linus/master v5.11 next-20210218]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Michael-Kelley/Enable-Linux-guests-on-Hyper-V-on-ARM64/20210219-072336
base:   https://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux.git for-next/core
config: i386-randconfig-a003-20210218 (attached as .config)
compiler: gcc-9 (Debian 9.3.0-15) 9.3.0
reproduce (this is a W=1 build):
        # https://github.com/0day-ci/linux/commit/a8eb25332c441e0965c0ecdfb1a86b507e3465e1
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Michael-Kelley/Enable-Linux-guests-on-Hyper-V-on-ARM64/20210219-072336
        git checkout a8eb25332c441e0965c0ecdfb1a86b507e3465e1
        # save the attached .config to linux build tree
        make W=1 ARCH=i386 

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All warnings (new ones prefixed by >>):

>> drivers/clocksource/hyperv_timer.c:478:44: warning: 'struct acpi_table_header' declared inside parameter list will not be visible outside of this definition or declaration
     478 | static int __init hyperv_timer_init(struct acpi_table_header *table)
         |                                            ^~~~~~~~~~~~~~~~~
   drivers/clocksource/hyperv_timer.c: In function 'hyperv_timer_init':
   drivers/clocksource/hyperv_timer.c:484:6: error: too many arguments to function 'hv_stimer_alloc'
     484 |  if (hv_stimer_alloc(true))
         |      ^~~~~~~~~~~~~~~
   drivers/clocksource/hyperv_timer.c:173:5: note: declared here
     173 | int hv_stimer_alloc(void)
         |     ^~~~~~~~~~~~~~~
   In file included from include/linux/clockchips.h:14,
                    from drivers/clocksource/hyperv_timer.c:16:
   drivers/clocksource/hyperv_timer.c: At top level:
   include/linux/clocksource.h:283:50: error: expected ')' before numeric constant
     283 |  ACPI_DECLARE_PROBE_ENTRY(timer, name, table_id, 0, NULL, 0, fn)
         |                                                  ^
   drivers/clocksource/hyperv_timer.c:489:1: note: in expansion of macro 'TIMER_ACPI_DECLARE'
     489 | TIMER_ACPI_DECLARE(hyperv, ACPI_SIG_GTDT, hyperv_timer_init);
         | ^~~~~~~~~~~~~~~~~~
   drivers/clocksource/hyperv_timer.c:478:19: warning: 'hyperv_timer_init' defined but not used [-Wunused-function]
     478 | static int __init hyperv_timer_init(struct acpi_table_header *table)
         |                   ^~~~~~~~~~~~~~~~~


vim +478 drivers/clocksource/hyperv_timer.c

   476	
   477	/* Initialize everything on ARM64 */
 > 478	static int __init hyperv_timer_init(struct acpi_table_header *table)

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 29415 bytes --]

Re: [PATCH v8 2/6] arm64: hyperv: Add Hyper-V clocksource/clockevent support

[kernel test robot]

[-- Attachment #1: Type: text/plain, Size: 3285 bytes --]

Hi Michael,

Thank you for the patch! Yet something to improve:

[auto build test ERROR on arm64/for-next/core]
[also build test ERROR on tip/timers/core efi/next linus/master v5.11 next-20210218]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Michael-Kelley/Enable-Linux-guests-on-Hyper-V-on-ARM64/20210219-072336
base:   https://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux.git for-next/core
config: i386-randconfig-a003-20210218 (attached as .config)
compiler: gcc-9 (Debian 9.3.0-15) 9.3.0
reproduce (this is a W=1 build):
        # https://github.com/0day-ci/linux/commit/a8eb25332c441e0965c0ecdfb1a86b507e3465e1
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Michael-Kelley/Enable-Linux-guests-on-Hyper-V-on-ARM64/20210219-072336
        git checkout a8eb25332c441e0965c0ecdfb1a86b507e3465e1
        # save the attached .config to linux build tree
        make W=1 ARCH=i386 

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All errors (new ones prefixed by >>):

   drivers/clocksource/hyperv_timer.c:478:44: warning: 'struct acpi_table_header' declared inside parameter list will not be visible outside of this definition or declaration
     478 | static int __init hyperv_timer_init(struct acpi_table_header *table)
         |                                            ^~~~~~~~~~~~~~~~~
   drivers/clocksource/hyperv_timer.c: In function 'hyperv_timer_init':
>> drivers/clocksource/hyperv_timer.c:484:6: error: too many arguments to function 'hv_stimer_alloc'
     484 |  if (hv_stimer_alloc(true))
         |      ^~~~~~~~~~~~~~~
   drivers/clocksource/hyperv_timer.c:173:5: note: declared here
     173 | int hv_stimer_alloc(void)
         |     ^~~~~~~~~~~~~~~
   In file included from include/linux/clockchips.h:14,
                    from drivers/clocksource/hyperv_timer.c:16:
   drivers/clocksource/hyperv_timer.c: At top level:
>> include/linux/clocksource.h:283:50: error: expected ')' before numeric constant
     283 |  ACPI_DECLARE_PROBE_ENTRY(timer, name, table_id, 0, NULL, 0, fn)
         |                                                  ^
   drivers/clocksource/hyperv_timer.c:489:1: note: in expansion of macro 'TIMER_ACPI_DECLARE'
     489 | TIMER_ACPI_DECLARE(hyperv, ACPI_SIG_GTDT, hyperv_timer_init);
         | ^~~~~~~~~~~~~~~~~~
   drivers/clocksource/hyperv_timer.c:478:19: warning: 'hyperv_timer_init' defined but not used [-Wunused-function]
     478 | static int __init hyperv_timer_init(struct acpi_table_header *table)
         |                   ^~~~~~~~~~~~~~~~~


vim +/hv_stimer_alloc +484 drivers/clocksource/hyperv_timer.c

   476	
   477	/* Initialize everything on ARM64 */
   478	static int __init hyperv_timer_init(struct acpi_table_header *table)
   479	{
   480		if (!hv_is_hyperv_initialized())
   481			return -EINVAL;
   482	
   483		hv_init_clocksource();
 > 484		if (hv_stimer_alloc(true))

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 29415 bytes --]

Re: [PATCH v8 1/6] arm64: hyperv: Add Hyper-V hypercall and register access utilities

[Wei Liu]

On Thu, Feb 18, 2021 at 03:16:29PM -0800, Michael Kelley wrote:
> hyperv-tlfs.h defines Hyper-V interfaces from the Hyper-V Top Level
> Functional Spec (TLFS), and #includes the architecture-independent
> part of hyperv-tlfs.h in include/asm-generic.  The published TLFS
> is distinctly oriented to x86/x64, so the ARM64-specific
> hyperv-tlfs.h includes information for ARM64 that is not yet formally
> published. The TLFS is available here:
> 
>   docs.microsoft.com/en-us/virtualization/hyper-v-on-windows/reference/tlfs
> 
> mshyperv.h defines Linux-specific structures and routines for
> interacting with Hyper-V on ARM64, and #includes the architecture-
> independent part of mshyperv.h in include/asm-generic.
> 
> Use these definitions to provide utility functions to make
> Hyper-V hypercalls and to get and set Hyper-V provided
> registers associated with a virtual processor.
> 
> Signed-off-by: Michael Kelley <mikelley@microsoft.com>

Reviewed-by: Wei Liu <wei.liu@kernel.org>

Re: [PATCH v8 1/6] arm64: hyperv: Add Hyper-V hypercall and register access utilities

[Boqun Feng]

On Thu, Feb 18, 2021 at 03:16:29PM -0800, Michael Kelley wrote:
[...]
> +
> +/*
> + * Get the value of a single VP register.  One version
> + * returns just 64 bits and another returns the full 128 bits.
> + * The two versions are separate to avoid complicating the
> + * calling sequence for the more frequently used 64 bit version.
> + */
> +
> +void __hv_get_vpreg_128(u32 msr,
> +			struct hv_get_vp_registers_input  *input,
> +			struct hv_get_vp_registers_output *res)
> +{
> +	u64	status;
> +
> +	input->header.partitionid = HV_PARTITION_ID_SELF;
> +	input->header.vpindex = HV_VP_INDEX_SELF;
> +	input->header.inputvtl = 0;
> +	input->element[0].name0 = msr;
> +	input->element[0].name1 = 0;
> +
> +
> +	status = hv_do_hypercall(
> +		HVCALL_GET_VP_REGISTERS | HV_HYPERCALL_REP_COMP_1,
> +		input, res);
> +
> +	/*
> +	 * Something is fundamentally broken in the hypervisor if
> +	 * getting a VP register fails. There's really no way to
> +	 * continue as a guest VM, so panic.
> +	 */
> +	BUG_ON((status & HV_HYPERCALL_RESULT_MASK) != HV_STATUS_SUCCESS);
> +}
> +
> +u64 hv_get_vpreg(u32 msr)
> +{
> +	struct hv_get_vp_registers_input	*input;
> +	struct hv_get_vp_registers_output	*output;
> +	u64					result;
> +
> +	/*
> +	 * Allocate a power of 2 size so alignment to that size is
> +	 * guaranteed, since the hypercall input and output areas
> +	 * must not cross a page boundary.
> +	 */
> +	input = kzalloc(roundup_pow_of_two(sizeof(input->header) +
> +				sizeof(input->element[0])), GFP_ATOMIC);
> +	output = kmalloc(roundup_pow_of_two(sizeof(*output)), GFP_ATOMIC);
> +

Do we need to BUG_ON(!input || !output)? Or we expect the page fault
(for input being NULL) or the failure of hypercall (for output being
NULL) to tell us the allocation failed?

Hmm.. think a bit more on this, maybe we'd better retry the allocation
if it failed. Because say we are under memory pressusre, and only have
memory enough for doing one hvcall, and one thread allocates that memory
but gets preempted by another thread trying to do another hvcall:

	<thread 1>
	hv_get_vpreg():
	  input = kzalloc(...);
	  output = kmalloc(...);
	<preempted and switch to thread 2>
	hv_get_vpreg():
	  intput = kzalloc(...); // allocation fails, but actually if
	                         // we wait for thread 1 to finish its
				 // hvcall, we can get enough memory.

, in this case, if thread 2 retried, it might get the enough memory,
therefore there is no need to BUG_ON() on allocation failure. That said,
I don't think this is likely to happen, and there may be better
solutions for this, so maybe we can keep it as it is (assuming that
memory allocation for hvcall never fails) and improve later.

Regards,
Boqun

> +	__hv_get_vpreg_128(msr, input, output);
> +
> +	result = output->as64.low;
> +	kfree(input);
> +	kfree(output);
> +	return result;
> +}
> +EXPORT_SYMBOL_GPL(hv_get_vpreg);
> +
> +void hv_get_vpreg_128(u32 msr, struct hv_get_vp_registers_output *res)
> +{
> +	struct hv_get_vp_registers_input	*input;
> +	struct hv_get_vp_registers_output	*output;
> +
> +	/*
> +	 * Allocate a power of 2 size so alignment to that size is
> +	 * guaranteed, since the hypercall input and output areas
> +	 * must not cross a page boundary.
> +	 */
> +	input = kzalloc(roundup_pow_of_two(sizeof(input->header) +
> +				sizeof(input->element[0])), GFP_ATOMIC);
> +	output = kmalloc(roundup_pow_of_two(sizeof(*output)), GFP_ATOMIC);
> +
> +	__hv_get_vpreg_128(msr, input, output);
> +
> +	res->as64.low = output->as64.low;
> +	res->as64.high = output->as64.high;
> +	kfree(input);
> +	kfree(output);
> +}
[...]

RE: [PATCH v8 1/6] arm64: hyperv: Add Hyper-V hypercall and register access utilities

[Michael Kelley]

From: Boqun Feng <boqun.feng@gmail.com> Sent: Tuesday, February 23, 2021 6:37 PM
> 
> On Thu, Feb 18, 2021 at 03:16:29PM -0800, Michael Kelley wrote:
> [...]
> > +
> > +/*
> > + * Get the value of a single VP register.  One version
> > + * returns just 64 bits and another returns the full 128 bits.
> > + * The two versions are separate to avoid complicating the
> > + * calling sequence for the more frequently used 64 bit version.
> > + */
> > +
> > +void __hv_get_vpreg_128(u32 msr,
> > +			struct hv_get_vp_registers_input  *input,
> > +			struct hv_get_vp_registers_output *res)
> > +{
> > +	u64	status;
> > +
> > +	input->header.partitionid = HV_PARTITION_ID_SELF;
> > +	input->header.vpindex = HV_VP_INDEX_SELF;
> > +	input->header.inputvtl = 0;
> > +	input->element[0].name0 = msr;
> > +	input->element[0].name1 = 0;
> > +
> > +
> > +	status = hv_do_hypercall(
> > +		HVCALL_GET_VP_REGISTERS | HV_HYPERCALL_REP_COMP_1,
> > +		input, res);
> > +
> > +	/*
> > +	 * Something is fundamentally broken in the hypervisor if
> > +	 * getting a VP register fails. There's really no way to
> > +	 * continue as a guest VM, so panic.
> > +	 */
> > +	BUG_ON((status & HV_HYPERCALL_RESULT_MASK) != HV_STATUS_SUCCESS);
> > +}
> > +
> > +u64 hv_get_vpreg(u32 msr)
> > +{
> > +	struct hv_get_vp_registers_input	*input;
> > +	struct hv_get_vp_registers_output	*output;
> > +	u64					result;
> > +
> > +	/*
> > +	 * Allocate a power of 2 size so alignment to that size is
> > +	 * guaranteed, since the hypercall input and output areas
> > +	 * must not cross a page boundary.
> > +	 */
> > +	input = kzalloc(roundup_pow_of_two(sizeof(input->header) +
> > +				sizeof(input->element[0])), GFP_ATOMIC);
> > +	output = kmalloc(roundup_pow_of_two(sizeof(*output)), GFP_ATOMIC);
> > +
> 
> Do we need to BUG_ON(!input || !output)? Or we expect the page fault
> (for input being NULL) or the failure of hypercall (for output being
> NULL) to tell us the allocation failed?
> 
> Hmm.. think a bit more on this, maybe we'd better retry the allocation
> if it failed. Because say we are under memory pressusre, and only have
> memory enough for doing one hvcall, and one thread allocates that memory
> but gets preempted by another thread trying to do another hvcall:
> 
> 	<thread 1>
> 	hv_get_vpreg():
> 	  input = kzalloc(...);
> 	  output = kmalloc(...);
> 	<preempted and switch to thread 2>
> 	hv_get_vpreg():
> 	  intput = kzalloc(...); // allocation fails, but actually if
> 	                         // we wait for thread 1 to finish its
> 				 // hvcall, we can get enough memory.
> 
> , in this case, if thread 2 retried, it might get the enough memory,
> therefore there is no need to BUG_ON() on allocation failure. That said,
> I don't think this is likely to happen, and there may be better
> solutions for this, so maybe we can keep it as it is (assuming that
> memory allocation for hvcall never fails) and improve later.
> 
> Regards,
> Boqun

Having to do these memory allocations in order to make a
hypercall results in a lot of messiness.  I've just gone back to
try again at doing hv_get_vpreg() and hv_get_vpreg_128()
as "fast" hypercalls that pass inputs (and outputs) in registers
like hv_set_vpreg().  I have it working now, with some tweaks
to arm_smccc_1_1_hvc() to allow outputs in a wider range
of registers than just X0 thru X3.  This wider range of registers
is allowed by the SMCCC version 1.2 and 1.3 specs, so hopefully
is acceptable.  I'll send out a new version using this "fast"
hypercall approach that completely avoids all these memory
allocation problems.

Michael

> 
> > +	__hv_get_vpreg_128(msr, input, output);
> > +
> > +	result = output->as64.low;
> > +	kfree(input);
> > +	kfree(output);
> > +	return result;
> > +}
> > +EXPORT_SYMBOL_GPL(hv_get_vpreg);
> > +
> > +void hv_get_vpreg_128(u32 msr, struct hv_get_vp_registers_output *res)
> > +{
> > +	struct hv_get_vp_registers_input	*input;
> > +	struct hv_get_vp_registers_output	*output;
> > +
> > +	/*
> > +	 * Allocate a power of 2 size so alignment to that size is
> > +	 * guaranteed, since the hypercall input and output areas
> > +	 * must not cross a page boundary.
> > +	 */
> > +	input = kzalloc(roundup_pow_of_two(sizeof(input->header) +
> > +				sizeof(input->element[0])), GFP_ATOMIC);
> > +	output = kmalloc(roundup_pow_of_two(sizeof(*output)), GFP_ATOMIC);
> > +
> > +	__hv_get_vpreg_128(msr, input, output);
> > +
> > +	res->as64.low = output->as64.low;
> > +	res->as64.high = output->as64.high;
> > +	kfree(input);
> > +	kfree(output);
> > +}
> [...]