linux-fscrypt.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Boris Burkov <boris@bur.io>
To: fstests@vger.kernel.org, linux-fscrypt@vger.kernel.org,
	linux-btrfs@vger.kernel.org, kernel-team@fb.com
Subject: [PATCH v4 3/4] btrfs: test verity orphans with dmlogwrites
Date: Wed,  5 May 2021 14:04:45 -0700	[thread overview]
Message-ID: <cb1ceb9bfafdbda7ea30ace02881f4045628bdb7.1620248200.git.boris@bur.io> (raw)
In-Reply-To: <cover.1620248200.git.boris@bur.io>

The behavior of orphans is most interesting across mounts, interrupted
at arbitrary points during fsverity enable. To cover as many such cases
as possible, use dmlogwrites and dmsnapshot as in
log-writes/replay-individual.sh. At each log entry, we want to assert a
somewhat complicated invariant:

If verity has not yet started: an orphan indicates that verity has
started.
If verity has started: mount should handle the orphan and blow away
verity data: expect 0 merkle items after mounting the snapshot dev. If
we can measure the file, verity has finished.
If verity has finished: the orphan should be gone, so mount should not
blow away merkle items. Expect the same number of merkle items before
and after mounting the snapshot dev.

Note that this relies on grepping btrfs inspect-internal dump-tree.
Until btrfs-progs has the ability to print the new Merkle items, they
will show up as UNKNOWN.36/37.

Signed-off-by: Boris Burkov <boris@bur.io>
---
 tests/btrfs/291     | 157 ++++++++++++++++++++++++++++++++++++++++++++
 tests/btrfs/291.out |   2 +
 tests/btrfs/group   |   1 +
 3 files changed, 160 insertions(+)
 create mode 100755 tests/btrfs/291
 create mode 100644 tests/btrfs/291.out

diff --git a/tests/btrfs/291 b/tests/btrfs/291
new file mode 100755
index 00000000..eab3a495
--- /dev/null
+++ b/tests/btrfs/291
@@ -0,0 +1,157 @@
+#! /bin/bash
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2021 Facebook, Inc. All Rights Reserved.
+#
+# FS QA Test 291
+#
+# Test btrfs consistency after each FUA while enabling verity on a file
+# This test works by following the pattern in log-writes/replay-individual.sh:
+# 1. run a workload (verity + sync) while logging to the log device
+# 2. replay an entry to the replay device
+# 3. snapshot the replay device to the snapshot device
+# 4. run destructive tests on the snapshot device (e.g. mount with orphans)
+# 5. goto 2
+#
+seq=`basename $0`
+seqres=$RESULT_DIR/$seq
+echo "QA output created by $seq"
+
+here=`pwd`
+tmp=/tmp/$$
+status=1	# failure is the default!
+trap "_cleanup; exit \$status" 0 1 2 3 15
+
+_cleanup()
+{
+	cd /
+	_log_writes_cleanup &> /dev/null
+	rm -f $tmp.*
+	$LVM_PROG vgremove -f -y $vgname >>$seqres.full 2>&1
+	losetup -d $loop_dev >>$seqres.full 2>&1
+}
+
+# get standard environment, filters and checks
+. ./common/rc
+. ./common/filter
+. ./common/attr
+. ./common/dmlogwrites
+. ./common/verity
+
+# remove previous $seqres.full before test
+rm -f $seqres.full
+
+# real QA test starts here
+
+_supported_fs btrfs
+
+_require_scratch
+_require_log_writes
+_require_dm_target snapshot
+_require_command $LVM_PROG lvm
+_require_scratch_verity
+
+sync_loop() {
+	i=$1
+	[ -z "$i" ] && _fail "sync loop needs a number of iterations"
+	while [ $i -gt 0 ]
+	do
+		$XFS_IO_PROG -c sync $SCRATCH_MNT
+		let i-=1
+	done
+}
+
+dump_tree() {
+	local dev=$1
+	$BTRFS_UTIL_PROG inspect-internal dump-tree $dev
+}
+
+count_item() {
+	local dev=$1
+	local item=$2
+	dump_tree $dev | grep -c $item
+}
+
+_log_writes_init $SCRATCH_DEV
+_log_writes_mkfs
+_log_writes_mount
+
+f=$SCRATCH_MNT/fsv
+MB=$((1024 * 1024))
+$XFS_IO_PROG -fc "pwrite -q 0 $((10 * $MB))" $f
+$XFS_IO_PROG -c sync $SCRATCH_MNT
+sync_loop 10 &
+_fsv_enable $f
+$XFS_IO_PROG -c sync $SCRATCH_MNT
+
+_log_writes_unmount
+_log_writes_remove
+
+$XFS_IO_PROG -fc "pwrite -q -S 0 $((8192 * $MB)) $MB" $tmp.loop-file
+loop_dev=$(losetup -f --show $tmp.loop-file)
+vgname=vg_replay
+lvname=lv_replay
+replay_dev=/dev/mapper/vg_replay-lv_replay
+snapname=lv_snap
+snap_dev=/dev/mapper/vg_replay-$snapname
+
+$LVM_PROG vgcreate -f $vgname $loop_dev >>$seqres.full 2>&1 || _fail "failed to vgcreate $vgname"
+$LVM_PROG lvcreate -L 4G -n $lvname $vgname -y >>$seqres.full 2>&1 || \
+	_fail "failed to lvcreate $lvname"
+$UDEV_SETTLE_PROG >>$seqres.full 2>&1
+
+replay_log_prog=$here/src/log-writes/replay-log
+num_entries=$($replay_log_prog --log $LOGWRITES_DEV --num-entries)
+entry=$($replay_log_prog --log $LOGWRITES_DEV --replay $replay_dev --find --end-mark mkfs | cut -d@ -f1)
+$replay_log_prog --log $LOGWRITES_DEV --replay $replay_dev --limit $entry || \
+	_fail "failed to replay to start entry $entry"
+let entry+=1
+
+# state = 0: verity hasn't started
+# state = 1: verity underway
+# state = 2: verity done
+state=0
+while [ $entry -lt $num_entries ];
+do
+	$replay_log_prog --limit 1 --log $LOGWRITES_DEV --replay $replay_dev --start $entry || \
+		_fail "failed to take replay step at entry: $entry"
+
+	$LVM_PROG lvcreate -s -L 4M -n $snapname $vgname/$lvname >>$seqres.full 2>&1 || \
+		_fail "Failed to create snapshot"
+	$UDEV_SETTLE_PROG >>$seqres.full 2>&1
+
+	orphan=$(count_item $snap_dev ORPHAN)
+	if [ $state -eq 0 ]; then
+		[ $orphan -gt 0 ] && state=1
+	fi
+
+	pre_mount=$(count_item $snap_dev UNKNOWN.3[67])
+	_mount $snap_dev $SCRATCH_MNT || _fail "mount failed at entry $entry"
+	fsverity measure $SCRATCH_MNT/fsv >>$seqres.full 2>&1
+	measured=$?
+	umount $SCRATCH_MNT
+	[ $state -eq 1 ] && [ $measured -eq 0 ] && state=2
+	[ $state -eq 2 ] && ([ $measured -eq 0 ] || _fail "verity done, but measurement failed at entry $entry")
+	post_mount=$(count_item $snap_dev UNKNOWN.3[67])
+
+	echo "entry: $entry, state: $state, orphan: $orphan, pre_mount: $pre_mount, post_mount: $post_mount" >> $seqres.full
+
+	if [ $state -eq 1 ]; then
+		[ $post_mount -eq 0 ] || \
+			_fail "mount failed to clear under-construction merkle items pre: $pre_mount, post: $post_mount at entry $entry";
+	fi
+	if [ $state -eq 2 ]; then
+		[ $pre_mount -gt 0 ] || \
+			_fail "expected to have verity items before mount at entry $entry"
+		[ $pre_mount -eq $post_mount ] || \
+			_fail "mount cleared merkle items after verity was enabled $pre_mount vs $post_mount at entry $entry";
+	fi
+
+	let entry+=1
+	$LVM_PROG lvremove $vgname/$snapname -y >>$seqres.full
+done
+
+echo "Silence is golden"
+
+# success, all done
+status=0
+exit
diff --git a/tests/btrfs/291.out b/tests/btrfs/291.out
new file mode 100644
index 00000000..04605c70
--- /dev/null
+++ b/tests/btrfs/291.out
@@ -0,0 +1,2 @@
+QA output created by 291
+Silence is golden
diff --git a/tests/btrfs/group b/tests/btrfs/group
index 13051562..cc5a811e 100644
--- a/tests/btrfs/group
+++ b/tests/btrfs/group
@@ -239,3 +239,4 @@
 234 auto quick compress rw
 235 auto quick send
 290 auto quick verity
+291 auto verity
-- 
2.30.2


  parent reply	other threads:[~2021-05-05 21:04 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-05-05 21:04 [PATCH v4 0/4] tests for btrfs fsverity Boris Burkov
2021-05-05 21:04 ` [PATCH v4 1/4] btrfs: test btrfs specific fsverity corruption Boris Burkov
2021-05-16 16:34   ` Eryu Guan
2021-05-05 21:04 ` [PATCH v4 2/4] generic/574: corrupt btrfs merkle tree data Boris Burkov
2021-05-16 16:38   ` Eryu Guan
2021-05-05 21:04 ` Boris Burkov [this message]
2021-05-16 16:43   ` [PATCH v4 3/4] btrfs: test verity orphans with dmlogwrites Eryu Guan
2021-05-05 21:04 ` [PATCH v4 4/4] generic: test fs-verity EFBIG scenarios Boris Burkov
2021-05-16 16:47   ` Eryu Guan
2021-05-25 20:24   ` Eric Biggers
2021-09-10 23:26     ` Boris Burkov
2021-09-10 23:32       ` Eric Biggers
2021-05-25 18:13 ` [PATCH v4 0/4] tests for btrfs fsverity Eric Biggers

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=cb1ceb9bfafdbda7ea30ace02881f4045628bdb7.1620248200.git.boris@bur.io \
    --to=boris@bur.io \
    --cc=fstests@vger.kernel.org \
    --cc=kernel-team@fb.com \
    --cc=linux-btrfs@vger.kernel.org \
    --cc=linux-fscrypt@vger.kernel.org \
    --subject='Re: [PATCH v4 3/4] btrfs: test verity orphans with dmlogwrites' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).