[PATCH 1/6] pinctrl: coh901: Pass irqchip when adding gpiochip

[Linus Walleij <linus.walleij@linaro.org>]

We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.

For chained irqchips this is a pretty straight-forward
conversion.

Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 drivers/pinctrl/pinctrl-coh901.c | 50 +++++++++++++++-----------------
 1 file changed, 23 insertions(+), 27 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-coh901.c b/drivers/pinctrl/pinctrl-coh901.c
index 08b9e909e917..063a629be9b2 100644
--- a/drivers/pinctrl/pinctrl-coh901.c
+++ b/drivers/pinctrl/pinctrl-coh901.c
@@ -616,6 +616,7 @@ static int __init u300_gpio_probe(struct platform_device *pdev)
 {
 	struct u300_gpio *gpio;
 	struct resource *memres;
+	struct gpio_irq_chip *girq;
 	int err = 0;
 	int portno;
 	u32 val;
@@ -672,26 +673,17 @@ static int __init u300_gpio_probe(struct platform_device *pdev)
 	       gpio->base + U300_GPIO_CR);
 	u300_gpio_init_coh901571(gpio);
 
-#ifdef CONFIG_OF_GPIO
-	gpio->chip.of_node = pdev->dev.of_node;
-#endif
-	err = gpiochip_add_data(&gpio->chip, gpio);
-	if (err) {
-		dev_err(gpio->dev, "unable to add gpiochip: %d\n", err);
-		goto err_no_chip;
-	}
-
-	err = gpiochip_irqchip_add(&gpio->chip,
-				   &u300_gpio_irqchip,
-				   0,
-				   handle_simple_irq,
-				   IRQ_TYPE_EDGE_FALLING);
-	if (err) {
-		dev_err(gpio->dev, "no GPIO irqchip\n");
-		goto err_no_irqchip;
+	girq = &gpio->chip.irq;
+	girq->chip = &u300_gpio_irqchip;
+	girq->parent_handler = u300_gpio_irq_handler;
+	girq->num_parents = U300_GPIO_NUM_PORTS;
+	girq->parents = devm_kcalloc(gpio->dev, U300_GPIO_NUM_PORTS,
+				     sizeof(*girq->parents),
+				     GFP_KERNEL);
+	if (!girq->parents) {
+		err = -ENOMEM;
+		goto err_dis_clk;
 	}
-
-	/* Add each port with its IRQ separately */
 	for (portno = 0 ; portno < U300_GPIO_NUM_PORTS; portno++) {
 		struct u300_gpio_port *port = &gpio->ports[portno];
 
@@ -700,16 +692,21 @@ static int __init u300_gpio_probe(struct platform_device *pdev)
 		port->gpio = gpio;
 
 		port->irq = platform_get_irq(pdev, portno);
-
-		gpiochip_set_chained_irqchip(&gpio->chip,
-					     &u300_gpio_irqchip,
-					     port->irq,
-					     u300_gpio_irq_handler);
+		girq->parents[portno] = port->irq;
 
 		/* Turns off irq force (test register) for this port */
 		writel(0x0, gpio->base + portno * gpio->stride + ifr);
 	}
-	dev_dbg(gpio->dev, "initialized %d GPIO ports\n", portno);
+	girq->default_type = IRQ_TYPE_EDGE_FALLING;
+	girq->handler = handle_simple_irq;
+#ifdef CONFIG_OF_GPIO
+	gpio->chip.of_node = pdev->dev.of_node;
+#endif
+	err = gpiochip_add_data(&gpio->chip, gpio);
+	if (err) {
+		dev_err(gpio->dev, "unable to add gpiochip: %d\n", err);
+		goto err_dis_clk;
+	}
 
 	/*
 	 * Add pinctrl pin ranges, the pin controller must be registered
@@ -729,9 +726,8 @@ static int __init u300_gpio_probe(struct platform_device *pdev)
 	return 0;
 
 err_no_range:
-err_no_irqchip:
 	gpiochip_remove(&gpio->chip);
-err_no_chip:
+err_dis_clk:
 	clk_disable_unprepare(gpio->clk);
 	dev_err(&pdev->dev, "module ERROR:%d\n", err);
 	return err;
-- 
2.21.0