From: Lars Povlsen <lars.povlsen@microchip.com>
To: SoC Team <soc@kernel.org>, Arnd Bergmann <arnd@arndb.de>,
Stephen Boyd <sboyd@kernel.org>,
Linus Walleij <linus.walleij@linaro.org>
Cc: Lars Povlsen <lars.povlsen@microchip.com>,
Steen Hegelund <Steen.Hegelund@microchip.com>,
Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>,
Olof Johansson <olof@lixom.net>,
"Michael Turquette" <mturquette@baylibre.com>,
<devicetree@vger.kernel.org>, <linux-clk@vger.kernel.org>,
<linux-gpio@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>,
Alexandre Belloni <alexandre.belloni@bootlin.com>
Subject: [PATCH v3 10/10] arm64: dts: sparx5: Add i2c devices, i2c muxes
Date: Mon, 15 Jun 2020 15:32:42 +0200 [thread overview]
Message-ID: <20200615133242.24911-11-lars.povlsen@microchip.com> (raw)
In-Reply-To: <20200615133242.24911-1-lars.povlsen@microchip.com>
This patch adds i2c devices and muxes to the Sparx5 reference boards.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
---
arch/arm64/boot/dts/microchip/sparx5.dtsi | 38 +++
.../boot/dts/microchip/sparx5_pcb125.dts | 4 +
.../dts/microchip/sparx5_pcb134_board.dtsi | 237 ++++++++++++++++++
.../dts/microchip/sparx5_pcb135_board.dtsi | 77 ++++++
.../boot/dts/microchip/sparx5_pcb_common.dtsi | 4 +
5 files changed, 360 insertions(+)
diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index 161846caf9c94..cf712e80615da 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -170,6 +170,44 @@ uart2_pins: uart2-pins {
pins = "GPIO_26", "GPIO_27";
function = "uart2";
};
+
+ i2c_pins: i2c-pins {
+ pins = "GPIO_14", "GPIO_15";
+ function = "twi";
+ };
+
+ i2c2_pins: i2c2-pins {
+ pins = "GPIO_28", "GPIO_29";
+ function = "twi2";
+ };
+ };
+
+ i2c0: i2c@600101000 {
+ compatible = "snps,designware-i2c";
+ status = "disabled";
+ pinctrl-0 = <&i2c_pins>;
+ pinctrl-names = "default";
+ reg = <0x6 0x00101000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ i2c-sda-hold-time-ns = <300>;
+ clock-frequency = <100000>;
+ clocks = <&ahb_clk>;
+ };
+
+ i2c1: i2c@600103000 {
+ compatible = "snps,designware-i2c";
+ status = "disabled";
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-names = "default";
+ reg = <0x6 0x00103000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ i2c-sda-hold-time-ns = <300>;
+ clock-frequency = <100000>;
+ clocks = <&ahb_clk>;
};
};
};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
index d7f985f7ee020..91ee5b6cfc37a 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
@@ -15,3 +15,7 @@ memory@0 {
reg = <0x00000000 0x00000000 0x10000000>;
};
};
+
+&i2c1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index 9b2aec400101b..18a535a043686 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -7,9 +7,246 @@
#include "sparx5_pcb_common.dtsi"
/{
+ aliases {
+ i2c0 = &i2c0;
+ i2c100 = &i2c100;
+ i2c101 = &i2c101;
+ i2c102 = &i2c102;
+ i2c103 = &i2c103;
+ i2c104 = &i2c104;
+ i2c105 = &i2c105;
+ i2c106 = &i2c106;
+ i2c107 = &i2c107;
+ i2c108 = &i2c108;
+ i2c109 = &i2c109;
+ i2c110 = &i2c110;
+ i2c111 = &i2c111;
+ i2c112 = &i2c112;
+ i2c113 = &i2c113;
+ i2c114 = &i2c114;
+ i2c115 = &i2c115;
+ i2c116 = &i2c116;
+ i2c117 = &i2c117;
+ i2c118 = &i2c118;
+ i2c119 = &i2c119;
+ };
+
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
priority = <200>;
};
};
+
+&gpio {
+ i2cmux_pins_i: i2cmux-pins-i {
+ pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19",
+ "GPIO_20", "GPIO_22", "GPIO_36", "GPIO_35",
+ "GPIO_50", "GPIO_51", "GPIO_56", "GPIO_57";
+ function = "twi_scl_m";
+ output-low;
+ };
+ i2cmux_0: i2cmux-0 {
+ pins = "GPIO_16";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_1: i2cmux-1 {
+ pins = "GPIO_17";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_2: i2cmux-2 {
+ pins = "GPIO_18";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_3: i2cmux-3 {
+ pins = "GPIO_19";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_4: i2cmux-4 {
+ pins = "GPIO_20";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_5: i2cmux-5 {
+ pins = "GPIO_22";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_6: i2cmux-6 {
+ pins = "GPIO_36";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_7: i2cmux-7 {
+ pins = "GPIO_35";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_8: i2cmux-8 {
+ pins = "GPIO_50";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_9: i2cmux-9 {
+ pins = "GPIO_51";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_10: i2cmux-10 {
+ pins = "GPIO_56";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_11: i2cmux-11 {
+ pins = "GPIO_57";
+ function = "twi_scl_m";
+ output-high;
+ };
+};
+
+&axi {
+ i2c0_imux: i2c0-imux@0 {
+ compatible = "i2c-mux-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-parent = <&i2c0>;
+ };
+ i2c0_emux: i2c0-emux@0 {
+ compatible = "i2c-mux-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-parent = <&i2c0>;
+ };
+};
+
+&i2c0_imux {
+ pinctrl-names =
+ "i2c100", "i2c101", "i2c102", "i2c103",
+ "i2c104", "i2c105", "i2c106", "i2c107",
+ "i2c108", "i2c109", "i2c110", "i2c111", "idle";
+ pinctrl-0 = <&i2cmux_0>;
+ pinctrl-1 = <&i2cmux_1>;
+ pinctrl-2 = <&i2cmux_2>;
+ pinctrl-3 = <&i2cmux_3>;
+ pinctrl-4 = <&i2cmux_4>;
+ pinctrl-5 = <&i2cmux_5>;
+ pinctrl-6 = <&i2cmux_6>;
+ pinctrl-7 = <&i2cmux_7>;
+ pinctrl-8 = <&i2cmux_8>;
+ pinctrl-9 = <&i2cmux_9>;
+ pinctrl-10 = <&i2cmux_10>;
+ pinctrl-11 = <&i2cmux_11>;
+ pinctrl-12 = <&i2cmux_pins_i>;
+ i2c100: i2c_sfp1 {
+ reg = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c101: i2c_sfp2 {
+ reg = <0x1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c102: i2c_sfp3 {
+ reg = <0x2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c103: i2c_sfp4 {
+ reg = <0x3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c104: i2c_sfp5 {
+ reg = <0x4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c105: i2c_sfp6 {
+ reg = <0x5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c106: i2c_sfp7 {
+ reg = <0x6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c107: i2c_sfp8 {
+ reg = <0x7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c108: i2c_sfp9 {
+ reg = <0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c109: i2c_sfp10 {
+ reg = <0x9>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c110: i2c_sfp11 {
+ reg = <0xa>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c111: i2c_sfp12 {
+ reg = <0xb>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&i2c0_emux {
+ mux-gpios = <&gpio 55 GPIO_ACTIVE_HIGH
+ &gpio 60 GPIO_ACTIVE_HIGH
+ &gpio 61 GPIO_ACTIVE_HIGH
+ &gpio 54 GPIO_ACTIVE_HIGH>;
+ idle-state = <0x8>;
+ i2c112: i2c_sfp13 {
+ reg = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c113: i2c_sfp14 {
+ reg = <0x1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c114: i2c_sfp15 {
+ reg = <0x2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c115: i2c_sfp16 {
+ reg = <0x3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c116: i2c_sfp17 {
+ reg = <0x4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c117: i2c_sfp18 {
+ reg = <0x5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c118: i2c_sfp19 {
+ reg = <0x6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c119: i2c_sfp20 {
+ reg = <0x7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index 9b2aec400101b..d71f11a10b3d2 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -7,9 +7,86 @@
#include "sparx5_pcb_common.dtsi"
/{
+ aliases {
+ i2c0 = &i2c0;
+ i2c152 = &i2c152;
+ i2c153 = &i2c153;
+ i2c154 = &i2c154;
+ i2c155 = &i2c155;
+ };
+
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
priority = <200>;
};
};
+
+&gpio {
+ i2cmux_pins_i: i2cmux-pins-i {
+ pins = "GPIO_35", "GPIO_36",
+ "GPIO_50", "GPIO_51";
+ function = "twi_scl_m";
+ output-low;
+ };
+ i2cmux_s29: i2cmux-0 {
+ pins = "GPIO_35";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_s30: i2cmux-1 {
+ pins = "GPIO_36";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_s31: i2cmux-2 {
+ pins = "GPIO_50";
+ function = "twi_scl_m";
+ output-high;
+ };
+ i2cmux_s32: i2cmux-3 {
+ pins = "GPIO_51";
+ function = "twi_scl_m";
+ output-high;
+ };
+};
+
+&axi {
+ i2c0_imux: i2c0-imux@0 {
+ compatible = "i2c-mux-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-parent = <&i2c0>;
+ };
+};
+
+&i2c0_imux {
+ pinctrl-names =
+ "i2c152", "i2c153", "i2c154", "i2c155",
+ "idle";
+ pinctrl-0 = <&i2cmux_s29>;
+ pinctrl-1 = <&i2cmux_s30>;
+ pinctrl-2 = <&i2cmux_s31>;
+ pinctrl-3 = <&i2cmux_s32>;
+ pinctrl-4 = <&i2cmux_pins_i>;
+ i2c152: i2c_sfp1 {
+ reg = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c153: i2c_sfp2 {
+ reg = <0x1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c154: i2c_sfp3 {
+ reg = <0x2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ i2c155: i2c_sfp4 {
+ reg = <0x3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb_common.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb_common.dtsi
index 1f99d0db1284f..9d1a082de3e29 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb_common.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb_common.dtsi
@@ -13,3 +13,7 @@ &uart0 {
&uart1 {
status = "okay";
};
+
+&i2c0 {
+ status = "okay";
+};
--
2.27.0
next prev parent reply other threads:[~2020-06-15 13:33 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-15 13:32 [PATCH v3 00/10] Adding support for Microchip Sparx5 SoC Lars Povlsen
2020-06-15 13:32 ` [PATCH v3 01/10] dt-bindings: arm: sparx5: Add documentation " Lars Povlsen
2020-07-13 18:40 ` Rob Herring
2020-06-15 13:32 ` [PATCH v3 02/10] arm64: sparx5: Add support for Microchip 2xA53 SoC Lars Povlsen
2020-06-15 13:32 ` [PATCH v3 03/10] arm64: dts: sparx5: Add basic cpu support Lars Povlsen
2020-06-15 13:32 ` [PATCH v3 04/10] arm64: dts: sparx5: Add pinctrl support Lars Povlsen
2020-06-15 13:32 ` [PATCH v3 05/10] pinctrl: ocelot: Add Sparx5 SoC support Lars Povlsen
2020-06-20 21:10 ` Linus Walleij
2020-06-22 7:54 ` Lars Povlsen
2020-07-07 11:58 ` Linus Walleij
2020-06-15 13:32 ` [PATCH v3 06/10] dt-bindings: clock: sparx5: Add Sparx5 SoC DPLL clock Lars Povlsen
2020-07-13 18:41 ` Rob Herring
2020-06-15 13:32 ` [PATCH v3 07/10] dt-bindings: clock: sparx5: Add bindings include file Lars Povlsen
2020-07-13 18:41 ` Rob Herring
2020-06-15 13:32 ` [PATCH v3 08/10] clk: sparx5: Add Sparx5 SoC DPLL clock driver Lars Povlsen
[not found] ` <159558008977.3847286.10561464126267966931@swboyd.mtv.corp.google.com>
2020-07-24 12:19 ` Lars Povlsen
2020-06-15 13:32 ` [PATCH v3 09/10] arm64: dts: sparx5: Add Sparx5 SoC DPLL clock Lars Povlsen
2020-06-15 13:32 ` Lars Povlsen [this message]
2020-07-22 20:32 ` [PATCH v3 00/10] Adding support for Microchip Sparx5 SoC Arnd Bergmann
2020-07-23 10:09 ` Lars Povlsen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200615133242.24911-11-lars.povlsen@microchip.com \
--to=lars.povlsen@microchip.com \
--cc=Steen.Hegelund@microchip.com \
--cc=UNGLinuxDriver@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=arnd@arndb.de \
--cc=devicetree@vger.kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=olof@lixom.net \
--cc=sboyd@kernel.org \
--cc=soc@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).