[PATCH V4 0/3] gpio: modepin: Add driver support for modepin GPIO controller

[PATCH V4 0/3] gpio: modepin: Add driver support for modepin GPIO controller

[Piyush Mehta]

This patch adds support for the zynqmp modepin GPIO controller and
documented for the same. GPIO modepin driver set and get the value and
status of the PS_MODE pin, based on device-tree pin configuration.
These four-bits boot-mode pins are dedicated configurable as input/output.
After the stabilization of the system,these mode pins are sampled.

To access GPIO pins, added Xilinx ZynqMP firmware MDIO API support to
set and get PS_MODE pins value and status. These APIs are interface
APIs, between the mode pin controller driver and low-level API.

---
Changes in v2:
- Added Xilinx ZynqMP firmware MMIO API support to set and get pin
  value and status.
- DT Documentation- Addressed review comments: Update commit message
- Modepin driver- Addressed review comments:
  - Update APIs
  - Removed unwanted variables
  - Handle return path for probe function

Review Comments:
https://lore.kernel.org/linux-arm-kernel/20210624205055.GA1961487@robh.at.kernel.org/T/#u

Changes in v3:
- Update example in dt-bindings documentation
- Update probe function return value
- Remove unnecessary print and header file

Review Comments:
https://lore.kernel.org/linux-arm-kernel/20210805174219.3000667-1-piyush.mehta@xilinx.com/#t

Changes in v4:
- Added input pin read status in modepin_gpio_get_value.
- Updated modepin control bit for out configuration.

Review Comments:
https://lore.kernel.org/linux-arm-kernel/554508f5-8cb5-3840-9f61-f6cd6e5745d2@xilinx.com/T/#u
---

Piyush Mehta (3):
  firmware: zynqmp: Add MMIO read and write support for PS_MODE pin
  dt-bindings: gpio: zynqmp: Add binding documentation for modepin
  gpio: modepin: Add driver support for modepin GPIO controller

 .../bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml    |  43 ++++++
 drivers/firmware/xilinx/zynqmp.c                   |  46 ++++++
 drivers/gpio/Kconfig                               |  12 ++
 drivers/gpio/Makefile                              |   1 +
 drivers/gpio/gpio-zynqmp-modepin.c                 | 162 +++++++++++++++++++++
 include/linux/firmware/xlnx-zynqmp.h               |  14 ++
 6 files changed, 278 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml
 create mode 100644 drivers/gpio/gpio-zynqmp-modepin.c

-- 
2.7.4

[PATCH V4 1/3] firmware: zynqmp: Add MMIO read and write support for PS_MODE pin

[Piyush Mehta]

Add Xilinx ZynqMP firmware MMIO APIs support to set and get PS_MODE
pins value and status. These APIs create an interface path between
mode pin controller driver and low-level API to access GPIO pins.

Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes in v2:
- Added Xilinx ZynqMP firmware MMIO API support to set and get pin
  value and status.
---
 drivers/firmware/xilinx/zynqmp.c     | 46 ++++++++++++++++++++++++++++++++++++
 include/linux/firmware/xlnx-zynqmp.h | 14 +++++++++++
 2 files changed, 60 insertions(+)

diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
index a3cadba..7feba12 100644
--- a/drivers/firmware/xilinx/zynqmp.c
+++ b/drivers/firmware/xilinx/zynqmp.c
@@ -28,6 +28,13 @@
 /* Max HashMap Order for PM API feature check (1<<7 = 128) */
 #define PM_API_FEATURE_CHECK_MAX_ORDER  7
 
+/* CRL registers and bitfields */
+#define CRL_APB_BASE			0xFF5E0000U
+/* BOOT_PIN_CTRL- Used to control the mode pins after boot */
+#define CRL_APB_BOOT_PIN_CTRL		(CRL_APB_BASE + (0x250U))
+/* BOOT_PIN_CTRL_MASK- out_val[11:8], out_en[3:0] */
+#define CRL_APB_BOOTPIN_CTRL_MASK	0xF0FU
+
 static bool feature_check_enabled;
 static DEFINE_HASHTABLE(pm_api_features_map, PM_API_FEATURE_CHECK_MAX_ORDER);
 
@@ -926,6 +933,45 @@ int zynqmp_pm_pinctrl_set_config(const u32 pin, const u32 param,
 EXPORT_SYMBOL_GPL(zynqmp_pm_pinctrl_set_config);
 
 /**
+ * zynqmp_pm_bootmode_read() - PM Config API for read bootpin status
+ * @ps_mode: Returned output value of ps_mode
+ *
+ * This API function is to be used for notify the power management controller
+ * to read bootpin status.
+ *
+ * Return: status, either success or error+reason
+ */
+unsigned int zynqmp_pm_bootmode_read(u32 *ps_mode)
+{
+	unsigned int ret;
+	u32 ret_payload[PAYLOAD_ARG_CNT];
+
+	ret = zynqmp_pm_invoke_fn(PM_MMIO_READ, CRL_APB_BOOT_PIN_CTRL, 0,
+				  0, 0, ret_payload);
+
+	*ps_mode = ret_payload[1];
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bootmode_read);
+
+/**
+ * zynqmp_pm_bootmode_write() - PM Config API for Configure bootpin
+ * @ps_mode: Value to be written to the bootpin ctrl register
+ *
+ * This API function is to be used for notify the power management controller
+ * to configure bootpin.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_bootmode_write(u32 ps_mode)
+{
+	return zynqmp_pm_invoke_fn(PM_MMIO_WRITE, CRL_APB_BOOT_PIN_CTRL,
+				   CRL_APB_BOOTPIN_CTRL_MASK, ps_mode, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bootmode_write);
+
+/**
  * zynqmp_pm_init_finalize() - PM call to inform firmware that the caller
  *			       master has initialized its own power management
  *
diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
index 56b426f..3917f89 100644
--- a/include/linux/firmware/xlnx-zynqmp.h
+++ b/include/linux/firmware/xlnx-zynqmp.h
@@ -72,6 +72,8 @@ enum pm_api_id {
 	PM_SET_REQUIREMENT = 15,
 	PM_RESET_ASSERT = 17,
 	PM_RESET_GET_STATUS = 18,
+	PM_MMIO_WRITE = 19,
+	PM_MMIO_READ = 20,
 	PM_PM_INIT_FINALIZE = 21,
 	PM_FPGA_LOAD = 22,
 	PM_FPGA_GET_STATUS = 23,
@@ -390,6 +392,8 @@ int zynqmp_pm_sd_dll_reset(u32 node_id, u32 type);
 int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
 			   const enum zynqmp_pm_reset_action assert_flag);
 int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset, u32 *status);
+unsigned int zynqmp_pm_bootmode_read(u32 *ps_mode);
+int zynqmp_pm_bootmode_write(u32 ps_mode);
 int zynqmp_pm_init_finalize(void);
 int zynqmp_pm_set_suspend_mode(u32 mode);
 int zynqmp_pm_request_node(const u32 node, const u32 capabilities,
@@ -520,6 +524,16 @@ static inline int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset,
 	return -ENODEV;
 }
 
+static inline unsigned int zynqmp_pm_bootmode_read(u32 *ps_mode)
+{
+	return -ENODEV;
+}
+
+static inline int zynqmp_pm_bootmode_write(u32 ps_mode)
+{
+	return -ENODEV;
+}
+
 static inline int zynqmp_pm_init_finalize(void)
 {
 	return -ENODEV;
-- 
2.7.4

[PATCH V4 2/3] dt-bindings: gpio: zynqmp: Add binding documentation for modepin

[Piyush Mehta]

This patch adds DT binding document for zynqmp modepin GPIO controller.
Modepin GPIO controller has four GPIO pins which can be configurable
as input or output.

Modepin driver is a bridge between the peripheral driver and GPIO pins.
It has set and get APIs for accessing GPIO pins, based on the device-tree
entry of reset-gpio property in the peripheral driver, every pin can be
configured as input/output and trigger GPIO pin.

For more information please refer zynqMp TRM link:
Link: https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf
Chapter 2: Signals, Interfaces, and Pins
Table 2-2: Clock, Reset, and Configuration Pins - PS_MODE

Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v2:
- Addressed review comments: Update commit message

Review Comments:
https://lore.kernel.org/linux-arm-kernel/20210615080553.2021061-2-piyush.mehta@xilinx.com/T/#mbd1fbda813e33b19397b350bde75747c92a0d7e1
https://lore.kernel.org/linux-arm-kernel/20210615080553.2021061-2-piyush.mehta@xilinx.com/T/#me82b1444ab3776162cdb0077dfc9256365c7e736

Changes in v3:
- Addressed Rob and Michal review comments:
  - Update DT example. 

Review Comments:
https://lore.kernel.org/linux-arm-kernel/YRbBnRS0VosXcZWz@robh.at.kernel.org/
https://lore.kernel.org/linux-arm-kernel/d71ad7f9-6972-8cc0-6dfb-b5306c9900d0@xilinx.com/
---
 .../bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml    | 41 ++++++++++++++++++++++
 .../bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml    | 43 ++++++++++++++++++++++
 1 file changed, 43 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml

diff --git a/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml b/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml
new file mode 100644
index 0000000..31c0fc3
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/gpio/xlnx,zynqmp-gpio-modepin.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: ZynqMP Mode Pin GPIO controller
+
+description:
+  PS_MODE is 4-bits boot mode pins sampled on POR deassertion. Mode Pin
+  GPIO controller with configurable from numbers of pins (from 0 to 3 per
+  PS_MODE). Every pin can be configured as input/output.
+
+maintainers:
+  - Piyush Mehta <piyush.mehta@xilinx.com>
+
+properties:
+  compatible:
+    const: xlnx,zynqmp-gpio-modepin
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+
+required:
+  - compatible
+  - gpio-controller
+  - "#gpio-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    zynqmp-firmware {
+        gpio {
+            compatible = "xlnx,zynqmp-gpio-modepin";
+            gpio-controller;
+            #gpio-cells = <2>;
+        };
+    };
+
+...
-- 
2.7.4

[PATCH V4 3/3] gpio: modepin: Add driver support for modepin GPIO controller

[Piyush Mehta]

This patch adds driver support for the zynqmp modepin GPIO controller.
GPIO modepin driver set and get the value and status of the PS_MODE pin,
based on device-tree pin configuration. These four mode pins are
configurable as input/output. The mode pin has a control register, which
have lower four-bits [0:3] are configurable as input/output, next four-bits
can be used for reading the data  as input[4:7], and next setting the
output pin state output[8:11]. By default value of mode pin register is 0.

Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes in v2:
- Modepin driver- Addressed review comments:
  - Update APIs
  - Removed unwanted variables
  - Handle return path for probe function

Review Comments:
https://lore.kernel.org/linux-arm-kernel/20210615080553.2021061-2-piyush.mehta@xilinx.com/T/#m276c8a5c52f8dc1ed1cd91a2d660f78d498e4ae5

Changes in v3:
- Addressed Linus and Arnd review comments:
  - Update probe function return value
  - Remove unnecessary print and header file
  - Update error message for set value method

Review Comments:
https://lore.kernel.org/linux-arm-kernel/20210805174219.3000667-4-piyush.mehta@xilinx.com/T/#m70acd39653033e32458633e21a2e6d21afdd16e6

Changes in v4:
- Added input pin read status in modepin_gpio_get_value.
- Updated modepin control bit for out configuration on set_value.

Review Comments:
https://lore.kernel.org/linux-arm-kernel/554508f5-8cb5-3840-9f61-f6cd6e5745d2@xilinx.com/T/#u
https://lore.kernel.org/linux-arm-kernel/554508f5-8cb5-3840-9f61-f6cd6e5745d2@xilinx.com/T/#m60039005ebee312260d344c7d4383acb43c50f0f
---
 drivers/gpio/Kconfig               |  12 +++
 drivers/gpio/Makefile              |   1 +
 drivers/gpio/gpio-zynqmp-modepin.c | 162 +++++++++++++++++++++++++++++++++++++
 3 files changed, 175 insertions(+)
 create mode 100644 drivers/gpio/gpio-zynqmp-modepin.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index fae5141..37a6f77 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -763,6 +763,18 @@ config GPIO_ZYNQ
 	help
 	  Say yes here to support Xilinx Zynq GPIO controller.
 
+config GPIO_ZYNQMP_MODEPIN
+	tristate "ZynqMP ps-mode pin gpio configuration driver"
+	depends on ZYNQMP_FIRMWARE
+	default ZYNQMP_FIRMWARE
+	help
+	  Say yes here to support the ZynqMP ps-mode pin gpio configuration
+	  driver.
+
+	  This ps-mode pin gpio driver is based on GPIO framework, PS_MODE
+	  is 4-bits boot mode pins. It sets and gets the status of
+	  the ps-mode pin. Every pin can be configured as input/output.
+
 config GPIO_LOONGSON1
 	tristate "Loongson1 GPIO support"
 	depends on MACH_LOONGSON32
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index fbcda63..71ee9fc2 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -184,3 +184,4 @@ obj-$(CONFIG_GPIO_XRA1403)		+= gpio-xra1403.o
 obj-$(CONFIG_GPIO_XTENSA)		+= gpio-xtensa.o
 obj-$(CONFIG_GPIO_ZEVIO)		+= gpio-zevio.o
 obj-$(CONFIG_GPIO_ZYNQ)			+= gpio-zynq.o
+obj-$(CONFIG_GPIO_ZYNQMP_MODEPIN)	+= gpio-zynqmp-modepin.o
diff --git a/drivers/gpio/gpio-zynqmp-modepin.c b/drivers/gpio/gpio-zynqmp-modepin.c
new file mode 100644
index 0000000..a0d6938
--- /dev/null
+++ b/drivers/gpio/gpio-zynqmp-modepin.c
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the ps-mode pin configuration.
+ *
+ * Copyright (c) 2021 Xilinx, Inc.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/firmware/xlnx-zynqmp.h>
+
+/* 4-bit boot mode pins */
+#define MODE_PINS			4
+
+/**
+ * modepin_gpio_get_value - Get the state of the specified pin of GPIO device
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ *
+ * This function reads the state of the specified pin of the GPIO device.
+ *
+ * Return: 0 if the pin is low, 1 if pin is high, -EINVAL wrong pin configured
+ *         or error value.
+ */
+static int modepin_gpio_get_value(struct gpio_chip *chip, unsigned int pin)
+{
+	u32 regval = 0;
+	int ret;
+
+	ret = zynqmp_pm_bootmode_read(&regval);
+	if (ret)
+		return ret;
+
+	/* When [0:3] corresponding bit is set, then read output bit [8:11],
+	 * if the bit is clear then read input bit [4:7] for status or value.
+	 */
+	if (regval & BIT(pin))
+		return !!(regval & BIT(pin + 8));
+	else
+		return !!(regval & BIT(pin + 4));
+}
+
+/**
+ * modepin_gpio_set_value - Modify the state of the pin with specified value
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ * @state:	value used to modify the state of the specified pin
+ *
+ * This function reads the state of the specified pin of the GPIO device, mask
+ * with the capture state of GPIO pin, and update pin of GPIO device.
+ *
+ * Return:	None.
+ */
+static void modepin_gpio_set_value(struct gpio_chip *chip, unsigned int pin,
+				   int state)
+{
+	u32 bootpin_val = 0;
+	int ret;
+
+	zynqmp_pm_bootmode_read(&bootpin_val);
+
+	/* Configure pin as an output by set bit [0:3] */
+	bootpin_val |= BIT(pin);
+
+	if (state)
+		bootpin_val |= BIT(pin + 8);
+	else
+		bootpin_val &= ~BIT(pin + 8);
+
+	/* Configure bootpin value */
+	ret = zynqmp_pm_bootmode_write(bootpin_val);
+	if (ret)
+		pr_err("modepin: set value error %d for pin %d\n", ret, pin);
+}
+
+/**
+ * modepin_gpio_dir_in - Set the direction of the specified GPIO pin as input
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ *
+ * Return: 0 always
+ */
+static int modepin_gpio_dir_in(struct gpio_chip *chip, unsigned int pin)
+{
+	return 0;
+}
+
+/**
+ * modepin_gpio_dir_out - Set the direction of the specified GPIO pin as output
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ * @state:	value to be written to specified pin
+ *
+ * Return: 0 always
+ */
+static int modepin_gpio_dir_out(struct gpio_chip *chip, unsigned int pin,
+				int state)
+{
+	return 0;
+}
+
+/**
+ * modepin_gpio_probe - Initialization method for modepin_gpio
+ * @pdev:		platform device instance
+ *
+ * Return: 0 on success, negative error otherwise.
+ */
+static int modepin_gpio_probe(struct platform_device *pdev)
+{
+	struct gpio_chip *chip;
+	int status;
+
+	chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, chip);
+
+	/* configure the gpio chip */
+	chip->base = -1;
+	chip->ngpio = MODE_PINS;
+	chip->owner = THIS_MODULE;
+	chip->parent = &pdev->dev;
+	chip->get = modepin_gpio_get_value;
+	chip->set = modepin_gpio_set_value;
+	chip->direction_input = modepin_gpio_dir_in;
+	chip->direction_output = modepin_gpio_dir_out;
+	chip->label = dev_name(&pdev->dev);
+
+	/* modepin gpio registration */
+	status = devm_gpiochip_add_data(&pdev->dev, chip, chip);
+	if (status)
+		return dev_err_probe(&pdev->dev, status,
+			      "Failed to add GPIO chip\n");
+
+	return status;
+}
+
+static const struct of_device_id modepin_platform_id[] = {
+	{ .compatible = "xlnx,zynqmp-gpio-modepin", },
+	{ }
+};
+
+static struct platform_driver modepin_platform_driver = {
+	.driver = {
+		.name = "modepin-gpio",
+		.of_match_table = modepin_platform_id,
+	},
+	.probe = modepin_gpio_probe,
+};
+
+module_platform_driver(modepin_platform_driver);
+
+MODULE_AUTHOR("Piyush Mehta <piyush.mehta@xilinx.com>");
+MODULE_DESCRIPTION("ZynqMP Boot PS_MODE Configuration");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4

Re: [PATCH V4 0/3] gpio: modepin: Add driver support for modepin GPIO controller

[Bartosz Golaszewski]

On Wed, Sep 22, 2021 at 3:53 PM Piyush Mehta <piyush.mehta@xilinx.com> wrote:
>
> This patch adds support for the zynqmp modepin GPIO controller and
> documented for the same. GPIO modepin driver set and get the value and
> status of the PS_MODE pin, based on device-tree pin configuration.
> These four-bits boot-mode pins are dedicated configurable as input/output.
> After the stabilization of the system,these mode pins are sampled.
>
> To access GPIO pins, added Xilinx ZynqMP firmware MDIO API support to
> set and get PS_MODE pins value and status. These APIs are interface
> APIs, between the mode pin controller driver and low-level API.
>
> ---
> Changes in v2:
> - Added Xilinx ZynqMP firmware MMIO API support to set and get pin
>   value and status.
> - DT Documentation- Addressed review comments: Update commit message
> - Modepin driver- Addressed review comments:
>   - Update APIs
>   - Removed unwanted variables
>   - Handle return path for probe function
>
> Review Comments:
> https://lore.kernel.org/linux-arm-kernel/20210624205055.GA1961487@robh.at.kernel.org/T/#u
>
> Changes in v3:
> - Update example in dt-bindings documentation
> - Update probe function return value
> - Remove unnecessary print and header file
>
> Review Comments:
> https://lore.kernel.org/linux-arm-kernel/20210805174219.3000667-1-piyush.mehta@xilinx.com/#t
>
> Changes in v4:
> - Added input pin read status in modepin_gpio_get_value.
> - Updated modepin control bit for out configuration.
>
> Review Comments:
> https://lore.kernel.org/linux-arm-kernel/554508f5-8cb5-3840-9f61-f6cd6e5745d2@xilinx.com/T/#u
> ---
>
> Piyush Mehta (3):
>   firmware: zynqmp: Add MMIO read and write support for PS_MODE pin
>   dt-bindings: gpio: zynqmp: Add binding documentation for modepin
>   gpio: modepin: Add driver support for modepin GPIO controller
>
>  .../bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml    |  43 ++++++
>  drivers/firmware/xilinx/zynqmp.c                   |  46 ++++++
>  drivers/gpio/Kconfig                               |  12 ++
>  drivers/gpio/Makefile                              |   1 +
>  drivers/gpio/gpio-zynqmp-modepin.c                 | 162 +++++++++++++++++++++
>  include/linux/firmware/xlnx-zynqmp.h               |  14 ++
>  6 files changed, 278 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/gpio/xlnx,zynqmp-gpio-modepin.yaml
>  create mode 100644 drivers/gpio/gpio-zynqmp-modepin.c
>
> --
> 2.7.4
>

Series queued for next. Thanks!

Bart