Linux-GPIO Archive on lore.kernel.org
 help / color / Atom feed
From: Bartosz Golaszewski <brgl@bgdev.pl>
To: Kent Gibson <warthog618@gmail.com>
Cc: Drew Fustini <drew@pdp7.com>,
	"open list:GPIO SUBSYSTEM" <linux-gpio@vger.kernel.org>,
	Linus Walleij <linus.walleij@linaro.org>,
	Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Subject: Re: [RFC] gpio: expose pull-up/pull-down line flags to userspace
Date: Wed, 9 Oct 2019 01:30:18 +0200
Message-ID: <CAMRc=MdcWUtEx3QAKxEmEEa1Effq7JpRPGNJOGfSYP6Nh0p1Hg@mail.gmail.com> (raw)
In-Reply-To: <20191008232120.GA9225@sol>

śr., 9 paź 2019 o 01:21 Kent Gibson <warthog618@gmail.com> napisał(a):
>
> On Tue, Oct 08, 2019 at 10:56:18PM +0200, Bartosz Golaszewski wrote:
> > wt., 8 paź 2019 o 08:15 Kent Gibson <warthog618@gmail.com> napisał(a):
> > >
> > > On Sat, Sep 21, 2019 at 12:25:23PM +0200, Drew Fustini wrote:
> > > > Add pull-up/pull-down flags to the gpio line get and
> > > > set ioctl() calls.  Use cases include a push button
> > > > that does not have an external resistor.
> > > >
> > > > Addition use cases described by Limor Fried (ladyada) of
> > > > Adafruit in this PR for Adafruit_Blinka Python lib:
> > > > https://github.com/adafruit/Adafruit_Blinka/pull/59
> > > >
> > > > Signed-off-by: Drew Fustini <drew@pdp7.com>
> > > > ---
> > > >  drivers/gpio/gpiolib.c    | 12 ++++++++++++
> > > >  include/uapi/linux/gpio.h |  4 ++++
> > > >  2 files changed, 16 insertions(+)
> > > >
> > > > diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
> > > > index d9074191edef..9da1093cc7f5 100644
> > > > --- a/drivers/gpio/gpiolib.c
> > > > +++ b/drivers/gpio/gpiolib.c
> > > > @@ -427,6 +427,8 @@ struct linehandle_state {
> > > >       (GPIOHANDLE_REQUEST_INPUT | \
> > > >       GPIOHANDLE_REQUEST_OUTPUT | \
> > > >       GPIOHANDLE_REQUEST_ACTIVE_LOW | \
> > > > +     GPIOHANDLE_REQUEST_PULL_UP | \
> > > > +     GPIOHANDLE_REQUEST_PULL_DOWN | \
> > > >       GPIOHANDLE_REQUEST_OPEN_DRAIN | \
> > > >       GPIOHANDLE_REQUEST_OPEN_SOURCE)
> > > >
> > > > @@ -598,6 +600,10 @@ static int linehandle_create(struct gpio_device *gdev, void __user *ip)
> > > >                       set_bit(FLAG_OPEN_DRAIN, &desc->flags);
> > > >               if (lflags & GPIOHANDLE_REQUEST_OPEN_SOURCE)
> > > >                       set_bit(FLAG_OPEN_SOURCE, &desc->flags);
> > > > +             if (lflags & GPIOHANDLE_REQUEST_PULL_DOWN)
> > > > +                     set_bit(FLAG_PULL_DOWN, &desc->flags);
> > > > +             if (lflags & GPIOHANDLE_REQUEST_PULL_UP)
> > > > +                     set_bit(FLAG_PULL_UP, &desc->flags);
> > > >
> > > >               ret = gpiod_set_transitory(desc, false);
> > > >               if (ret < 0)
> > > > @@ -1102,6 +1108,10 @@ static long gpio_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
> > > >               if (test_bit(FLAG_OPEN_SOURCE, &desc->flags))
> > > >                       lineinfo.flags |= (GPIOLINE_FLAG_OPEN_SOURCE |
> > > >                                          GPIOLINE_FLAG_IS_OUT);
> > > > +             if (test_bit(FLAG_PULL_DOWN, &desc->flags))
> > > > +                     lineinfo.flags |= GPIOLINE_FLAG_PULL_DOWN;
> > > > +             if (test_bit(FLAG_PULL_UP, &desc->flags))
> > > > +                     lineinfo.flags |= GPIOLINE_FLAG_PULL_UP;
> > > >
> > > >               if (copy_to_user(ip, &lineinfo, sizeof(lineinfo)))
> > > >                       return -EFAULT;
> > > > @@ -2475,6 +2485,8 @@ static bool gpiod_free_commit(struct gpio_desc *desc)
> > > >               clear_bit(FLAG_REQUESTED, &desc->flags);
> > > >               clear_bit(FLAG_OPEN_DRAIN, &desc->flags);
> > > >               clear_bit(FLAG_OPEN_SOURCE, &desc->flags);
> > > > +             clear_bit(FLAG_PULL_UP, &desc->flags);
> > > > +             clear_bit(FLAG_PULL_DOWN, &desc->flags);
> > > >               clear_bit(FLAG_IS_HOGGED, &desc->flags);
> > > >               ret = true;
> > > >       }
> > > > diff --git a/include/uapi/linux/gpio.h b/include/uapi/linux/gpio.h
> > > > index 4ebfe0ac6c5b..c2d1f7d908d6 100644
> > > > --- a/include/uapi/linux/gpio.h
> > > > +++ b/include/uapi/linux/gpio.h
> > > > @@ -33,6 +33,8 @@ struct gpiochip_info {
> > > >  #define GPIOLINE_FLAG_ACTIVE_LOW     (1UL << 2)
> > > >  #define GPIOLINE_FLAG_OPEN_DRAIN     (1UL << 3)
> > > >  #define GPIOLINE_FLAG_OPEN_SOURCE    (1UL << 4)
> > > > +#define GPIOLINE_FLAG_PULL_UP        (1UL << 5)
> > > > +#define GPIOLINE_FLAG_PULL_DOWN      (1UL << 6)
> > > >
> > > >  /**
> > > >   * struct gpioline_info - Information about a certain GPIO line
> > > > @@ -62,6 +64,8 @@ struct gpioline_info {
> > > >  #define GPIOHANDLE_REQUEST_ACTIVE_LOW        (1UL << 2)
> > > >  #define GPIOHANDLE_REQUEST_OPEN_DRAIN        (1UL << 3)
> > > >  #define GPIOHANDLE_REQUEST_OPEN_SOURCE       (1UL << 4)
> > > > +#define GPIOHANDLE_REQUEST_PULL_UP   (1UL << 5)
> > > > +#define GPIOHANDLE_REQUEST_PULL_DOWN (1UL << 6)
> > > >
> > > >  /**
> > > >   * struct gpiohandle_request - Information about a GPIO handle request
> > > > --
> > > > 2.20.1
> > > >
> > > Sorry for the late feedback, but I'm still not sure whether this patch
> > > is on track to be applied or not.  I had thought not, at least not yet,
> > > but just in case...
> > >
> >
> > It still needs some fixes, but Linus seems to be fine with the general idea.
> >
> > > You have added the flags to linehandle_create, but not lineevent_create.
> > > Given that your primary use case is push buttons, isn't the event request
> > > at least as important as the handle request?  Even ignoring your use
> > > case, I'd add them to lineevent_create just to maintain symmetry.
> > >
> > > Also, is it valid to set PULL_UP and PULL_DOWN simulaneously?
> > > I would think not, but I could be wrong.
> > > If not then that combination should be rejected with EINVAL.
> > >
> >
> > Yes, some validity checks of the flags must be added. I even did it in
> > my local branch[1].
> >
> Your changes for linehandle_create look ok, but for lineevent_create
> you explicitly disabled PULL_UP and PULL_DOWN, and in a block labelled
> "This is just wrong: we don't look for events on output lines" at that.
>

Yeah, feel free to change it.

> > Re: direction and configuration changes on requested lines: I think
> > it's quite useful to add in the form of a new ioctl():
> > GPIOHANDLE_SET_CONFIG_IOCTL or something. I started hacking on this
> > but eventually got more busy this week than I anticipated. I'm still
> > planning on sending an RFC by the end of the week though.
> >
> I have the reverse problem - bored and looking for something to do, so
> more than willing to help out - if you want it.
>

Sure, in that case let's just wait for your patches. You can just
extend what I started, if you wish.

> And while we're talking, does the gpio-mockup support pull up/down
> being set from the kernel side?
>

No, but feel free to add it.

Bart

> Cheers,
> Kent.
> >
> > [1] https://github.com/brgl/linux/commit/82fc38f6ab599ee03f7a8ed078de8abb41e6e611
> >
> > > Cheers,
> > > Kent.

  reply index

Thread overview: 35+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-09-21 10:25 Drew Fustini
2019-09-23  8:38 ` Bartosz Golaszewski
2019-10-02 11:10   ` Drew Fustini
2019-10-03 12:47   ` Linus Walleij
2019-10-04  7:22     ` Bartosz Golaszewski
2019-10-04 12:46       ` Bartosz Golaszewski
2019-10-05 17:02       ` Linus Walleij
2019-10-06  3:12         ` Kent Gibson
2019-10-06 21:06           ` Linus Walleij
2019-10-07  4:37             ` Kent Gibson
2019-10-08  6:15 ` Kent Gibson
2019-10-08 20:56   ` Bartosz Golaszewski
2019-10-08 23:21     ` Kent Gibson
2019-10-08 23:30       ` Bartosz Golaszewski [this message]
2019-10-08 23:56         ` Kent Gibson
2019-10-09  0:03           ` Bartosz Golaszewski
2019-10-09  0:22             ` Kent Gibson
2019-10-09  6:55               ` Kent Gibson
2019-10-09 12:57                 ` Drew Fustini
2019-10-09 13:23                   ` Kent Gibson
2019-10-09 13:30                 ` Drew Fustini
2019-10-09 14:11                   ` Kent Gibson
2019-10-09 15:50                     ` Bartosz Golaszewski
2019-10-09 16:19                       ` Kent Gibson
2019-10-09 23:59                   ` Kent Gibson
2019-10-10  7:47                     ` Drew Fustini
2019-10-10 10:14                       ` Kent Gibson
2019-10-10 11:17                         ` Kent Gibson
2019-10-11 13:04                           ` Drew Fustini
2019-10-11 13:06                         ` Drew Fustini
2019-10-11 13:49                           ` Kent Gibson
2019-10-09 11:32               ` Drew Fustini
2019-10-09 13:57       ` Drew Fustini
2019-10-09 14:01         ` Kent Gibson
2019-10-09 11:46   ` Drew Fustini

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to='CAMRc=MdcWUtEx3QAKxEmEEa1Effq7JpRPGNJOGfSYP6Nh0p1Hg@mail.gmail.com' \
    --to=brgl@bgdev.pl \
    --cc=drew@pdp7.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=thomas.petazzoni@bootlin.com \
    --cc=warthog618@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-GPIO Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-gpio/0 linux-gpio/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-gpio linux-gpio/ https://lore.kernel.org/linux-gpio \
		linux-gpio@vger.kernel.org
	public-inbox-index linux-gpio

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-gpio


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git