From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
To: Baruch Siach <baruch@tkos.co.il>
Cc: "Thierry Reding" <thierry.reding@gmail.com>,
"Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>,
"Lee Jones" <lee.jones@linaro.org>,
"Linus Walleij" <linus.walleij@linaro.org>,
"Rob Herring" <robh+dt@kernel.org>,
"Andrew Lunn" <andrew@lunn.ch>,
"Gregory Clement" <gregory.clement@bootlin.com>,
"Russell King" <linux@armlinux.org.uk>,
"Sebastian Hesselbarth" <sebastian.hesselbarth@gmail.com>,
"Thomas Petazzoni" <thomas.petazzoni@bootlin.com>,
"Chris Packham" <chris.packham@alliedtelesis.co.nz>,
"Sascha Hauer" <s.hauer@pengutronix.de>,
"Ralph Sennhauser" <ralph.sennhauser@gmail.com>,
linux-pwm@vger.kernel.org,
linux-gpio <linux-gpio@vger.kernel.org>,
arm-soc <linux-arm-kernel@lists.infradead.org>,
linux-devicetree <devicetree@vger.kernel.org>
Subject: Re: [PATCH v7 1/3] gpio: mvebu: add pwm support for Armada 8K/7K
Date: Fri, 22 Jan 2021 13:58:51 +0100 [thread overview]
Message-ID: <CAMpxmJUGHqJ0C9A84LBF_xzwjbqwFnUnYqFTGBg2CXhKUWd-zg@mail.gmail.com> (raw)
In-Reply-To: <ba8d5d482a98690140e02c3a35506490e0c6ecb4.1610364681.git.baruch@tkos.co.il>
On Mon, Jan 11, 2021 at 12:47 PM Baruch Siach <baruch@tkos.co.il> wrote:
>
> Use the marvell,pwm-offset DT property to store the location of PWM
> signal duration registers.
>
> Since we have more than two GPIO chips per system, we can't use the
> alias id to differentiate between them. Use the offset value for that.
>
> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
> ---
> drivers/gpio/gpio-mvebu.c | 101 +++++++++++++++++++++++++-------------
> 1 file changed, 68 insertions(+), 33 deletions(-)
>
> diff --git a/drivers/gpio/gpio-mvebu.c b/drivers/gpio/gpio-mvebu.c
> index 4261e3b22b4e..6bd45c59056a 100644
> --- a/drivers/gpio/gpio-mvebu.c
> +++ b/drivers/gpio/gpio-mvebu.c
> @@ -70,7 +70,12 @@
> */
> #define PWM_BLINK_ON_DURATION_OFF 0x0
> #define PWM_BLINK_OFF_DURATION_OFF 0x4
> +#define PWM_BLINK_COUNTER_B_OFF 0x8
>
> +/* Armada 8k variant gpios register offsets */
> +#define AP80X_GPIO0_OFF_A8K 0x1040
> +#define CP11X_GPIO0_OFF_A8K 0x100
> +#define CP11X_GPIO1_OFF_A8K 0x140
>
> /* The MV78200 has per-CPU registers for edge mask and level mask */
> #define GPIO_EDGE_MASK_MV78200_OFF(cpu) ((cpu) ? 0x30 : 0x18)
> @@ -93,6 +98,7 @@
>
> struct mvebu_pwm {
> struct regmap *regs;
> + u32 offset;
> unsigned long clk_rate;
> struct gpio_desc *gpiod;
> struct pwm_chip chip;
> @@ -283,12 +289,12 @@ mvebu_gpio_write_level_mask(struct mvebu_gpio_chip *mvchip, u32 val)
> */
> static unsigned int mvebu_pwmreg_blink_on_duration(struct mvebu_pwm *mvpwm)
> {
> - return PWM_BLINK_ON_DURATION_OFF;
> + return mvpwm->offset + PWM_BLINK_ON_DURATION_OFF;
> }
>
> static unsigned int mvebu_pwmreg_blink_off_duration(struct mvebu_pwm *mvpwm)
> {
> - return PWM_BLINK_OFF_DURATION_OFF;
> + return mvpwm->offset + PWM_BLINK_OFF_DURATION_OFF;
> }
>
> /*
> @@ -775,51 +781,80 @@ static int mvebu_pwm_probe(struct platform_device *pdev,
> struct device *dev = &pdev->dev;
> struct mvebu_pwm *mvpwm;
> void __iomem *base;
> + u32 offset;
> u32 set;
>
> - if (!of_device_is_compatible(mvchip->chip.of_node,
> - "marvell,armada-370-gpio"))
> - return 0;
> -
> - /*
> - * There are only two sets of PWM configuration registers for
> - * all the GPIO lines on those SoCs which this driver reserves
> - * for the first two GPIO chips. So if the resource is missing
> - * we can't treat it as an error.
> - */
> - if (!platform_get_resource_byname(pdev, IORESOURCE_MEM, "pwm"))
> + if (of_device_is_compatible(mvchip->chip.of_node,
> + "marvell,armada-370-gpio")) {
> + /*
> + * There are only two sets of PWM configuration registers for
> + * all the GPIO lines on those SoCs which this driver reserves
> + * for the first two GPIO chips. So if the resource is missing
> + * we can't treat it as an error.
> + */
> + if (!platform_get_resource_byname(pdev, IORESOURCE_MEM, "pwm"))
> + return 0;
> + offset = 0;
> + } else if (mvchip->soc_variant == MVEBU_GPIO_SOC_VARIANT_A8K) {
> + int ret = of_property_read_u32(dev->of_node,
> + "marvell,pwm-offset", &offset);
> + if (ret < 0)
> + return 0;
> + } else {
> return 0;
> + }
>
> if (IS_ERR(mvchip->clk))
> return PTR_ERR(mvchip->clk);
>
> - /*
> - * Use set A for lines of GPIO chip with id 0, B for GPIO chip
> - * with id 1. Don't allow further GPIO chips to be used for PWM.
> - */
> - if (id == 0)
> - set = 0;
> - else if (id == 1)
> - set = U32_MAX;
> - else
> - return -EINVAL;
> - regmap_write(mvchip->regs,
> - GPIO_BLINK_CNT_SELECT_OFF + mvchip->offset, set);
> -
> mvpwm = devm_kzalloc(dev, sizeof(struct mvebu_pwm), GFP_KERNEL);
> if (!mvpwm)
> return -ENOMEM;
> mvchip->mvpwm = mvpwm;
> mvpwm->mvchip = mvchip;
> + mvpwm->offset = offset;
> +
> + if (mvchip->soc_variant == MVEBU_GPIO_SOC_VARIANT_A8K) {
> + mvpwm->regs = mvchip->regs;
> +
> + switch (mvchip->offset) {
> + case AP80X_GPIO0_OFF_A8K:
> + case CP11X_GPIO0_OFF_A8K:
> + /* Blink counter A */
> + set = 0;
> + break;
> + case CP11X_GPIO1_OFF_A8K:
> + /* Blink counter B */
> + set = U32_MAX;
> + mvpwm->offset += PWM_BLINK_COUNTER_B_OFF;
> + break;
> + default:
> + return -EINVAL;
> + }
> + } else {
> + base = devm_platform_ioremap_resource_byname(pdev, "pwm");
> + if (IS_ERR(base))
> + return PTR_ERR(base);
>
> - base = devm_platform_ioremap_resource_byname(pdev, "pwm");
> - if (IS_ERR(base))
> - return PTR_ERR(base);
> + mvpwm->regs = devm_regmap_init_mmio(&pdev->dev, base,
> + &mvebu_gpio_regmap_config);
> + if (IS_ERR(mvpwm->regs))
> + return PTR_ERR(mvpwm->regs);
>
> - mvpwm->regs = devm_regmap_init_mmio(&pdev->dev, base,
> - &mvebu_gpio_regmap_config);
> - if (IS_ERR(mvpwm->regs))
> - return PTR_ERR(mvpwm->regs);
> + /*
> + * Use set A for lines of GPIO chip with id 0, B for GPIO chip
> + * with id 1. Don't allow further GPIO chips to be used for PWM.
> + */
> + if (id == 0)
> + set = 0;
> + else if (id == 1)
> + set = U32_MAX;
> + else
> + return -EINVAL;
> + }
> +
> + regmap_write(mvchip->regs,
> + GPIO_BLINK_CNT_SELECT_OFF + mvchip->offset, set);
Hi Baruch!
Can you confirm that this line is on purpose and that it should be
executed even for chips that use a separate regmap for PWM?
Bartosz
>
> mvpwm->clk_rate = clk_get_rate(mvchip->clk);
> if (!mvpwm->clk_rate) {
> --
> 2.29.2
>
next prev parent reply other threads:[~2021-01-22 13:00 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-11 11:46 [PATCH v7 0/3] gpio: mvebu: Armada 8K/7K PWM support Baruch Siach
2021-01-11 11:46 ` [PATCH v7 1/3] gpio: mvebu: add pwm support for Armada 8K/7K Baruch Siach
2021-01-22 12:58 ` Bartosz Golaszewski [this message]
2021-01-24 6:17 ` Baruch Siach
2021-01-11 11:46 ` [PATCH v7 2/3] arm64: dts: armada: add pwm offsets for ap/cp gpios Baruch Siach
2021-01-25 9:50 ` Bartosz Golaszewski
[not found] ` <87tuqzspnu.fsf@BL-laptop>
2021-02-02 11:27 ` Bartosz Golaszewski
2021-01-11 11:46 ` [PATCH v7 3/3] dt-bindings: ap806: document gpio marvell,pwm-offset property Baruch Siach
2021-01-12 8:49 ` Linus Walleij
2021-01-12 10:36 ` Russell King - ARM Linux admin
2021-01-18 13:37 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAMpxmJUGHqJ0C9A84LBF_xzwjbqwFnUnYqFTGBg2CXhKUWd-zg@mail.gmail.com \
--to=bgolaszewski@baylibre.com \
--cc=andrew@lunn.ch \
--cc=baruch@tkos.co.il \
--cc=chris.packham@alliedtelesis.co.nz \
--cc=devicetree@vger.kernel.org \
--cc=gregory.clement@bootlin.com \
--cc=lee.jones@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-pwm@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=ralph.sennhauser@gmail.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=sebastian.hesselbarth@gmail.com \
--cc=thierry.reding@gmail.com \
--cc=thomas.petazzoni@bootlin.com \
--cc=u.kleine-koenig@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).