Linux-Hwmon Archive on lore.kernel.org
 help / Atom feed
* [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support
@ 2019-02-04 20:19 Jeremy Gebben
  2019-02-04 20:19 ` [PATCH v3 1/4] hwmon: (lm85) remove freq_map size hardcodes Jeremy Gebben
                   ` (4 more replies)
  0 siblings, 5 replies; 7+ messages in thread
From: Jeremy Gebben @ 2019-02-04 20:19 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, linux-hwmon, linux-kernel

Hi,

This patch set adds support for the PWM frequencies from 22.5 to 30 kHz
available on the LM96000.

It looks like this chip has been supported for a long time, but wasn't
mentioned in the docs (which I have updated).

I stumbled on to a 10 year old thread discussing a patch which looks
like an early attempt to add support for this chip, which may be of
interest:
https://lm-sensors.lm-sensors.narkive.com/1SIwaMDT/patch-hwmon-lm96000-support

Thanks for reviewing,

Jeremy

Changes since v1:
 - replace freq_map_mask with freq_map_size

Changes since v2:
 - add lm96000 type instead of continuing to use lm85

Jeremy Gebben (4):
  hwmon: (lm85) remove freq_map size hardcodes
  dt-bindings: Add LM96000 as a trivial device
  hwmon: (lm85) support the LM96000
  hwmon: (lm85) add support for LM96000 high frequencies

 .../devicetree/bindings/trivial-devices.yaml  |  2 +
 Documentation/hwmon/lm85                      |  9 +++-
 drivers/hwmon/lm85.c                          | 43 +++++++++++++------
 3 files changed, 41 insertions(+), 13 deletions(-)

-- 
2.17.1


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 1/4] hwmon: (lm85) remove freq_map size hardcodes
  2019-02-04 20:19 [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support Jeremy Gebben
@ 2019-02-04 20:19 ` Jeremy Gebben
  2019-02-04 20:19 ` [PATCH v3 2/4] dt-bindings: Add LM96000 as a trivial device Jeremy Gebben
                   ` (3 subsequent siblings)
  4 siblings, 0 replies; 7+ messages in thread
From: Jeremy Gebben @ 2019-02-04 20:19 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, linux-hwmon, linux-kernel

Allow support for chips that support more than 8 frequencies.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
---
 drivers/hwmon/lm85.c | 25 +++++++++++++++----------
 1 file changed, 15 insertions(+), 10 deletions(-)

diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c
index 0a325878e8f5..4b15193d195c 100644
--- a/drivers/hwmon/lm85.c
+++ b/drivers/hwmon/lm85.c
@@ -198,13 +198,13 @@ static int RANGE_TO_REG(long range)
 #define RANGE_FROM_REG(val)	lm85_range_map[(val) & 0x0f]
 
 /* These are the PWM frequency encodings */
-static const int lm85_freq_map[8] = { /* 1 Hz */
+static const int lm85_freq_map[] = { /* 1 Hz */
 	10, 15, 23, 30, 38, 47, 61, 94
 };
-static const int adm1027_freq_map[8] = { /* 1 Hz */
+
+static const int adm1027_freq_map[] = { /* 1 Hz */
 	11, 15, 22, 29, 35, 44, 59, 88
 };
-#define FREQ_MAP_LEN	8
 
 static int FREQ_TO_REG(const int *map,
 		       unsigned int map_size, unsigned long freq)
@@ -212,9 +212,9 @@ static int FREQ_TO_REG(const int *map,
 	return find_closest(freq, map, map_size);
 }
 
-static int FREQ_FROM_REG(const int *map, u8 reg)
+static int FREQ_FROM_REG(const int *map, unsigned int map_size, u8 reg)
 {
-	return map[reg & 0x07];
+	return map[reg % map_size];
 }
 
 /*
@@ -296,6 +296,8 @@ struct lm85_data {
 	struct i2c_client *client;
 	const struct attribute_group *groups[6];
 	const int *freq_map;
+	unsigned int freq_map_size;
+
 	enum chips type;
 
 	bool has_vid5;	/* true if VID5 is configured for ADT7463 or ADT7468 */
@@ -514,7 +516,7 @@ static struct lm85_data *lm85_update_device(struct device *dev)
 			data->autofan[i].config =
 			    lm85_read_value(client, LM85_REG_AFAN_CONFIG(i));
 			val = lm85_read_value(client, LM85_REG_AFAN_RANGE(i));
-			data->pwm_freq[i] = val & 0x07;
+			data->pwm_freq[i] = val % data->freq_map_size;
 			data->zone[i].range = val >> 4;
 			data->autofan[i].min_pwm =
 			    lm85_read_value(client, LM85_REG_AFAN_MINPWM(i));
@@ -791,7 +793,8 @@ static ssize_t show_pwm_freq(struct device *dev,
 	if (IS_ADT7468_HFPWM(data))
 		freq = 22500;
 	else
-		freq = FREQ_FROM_REG(data->freq_map, data->pwm_freq[nr]);
+		freq = FREQ_FROM_REG(data->freq_map, data->freq_map_size,
+				     data->pwm_freq[nr]);
 
 	return sprintf(buf, "%d\n", freq);
 }
@@ -820,7 +823,7 @@ static ssize_t set_pwm_freq(struct device *dev,
 		lm85_write_value(client, ADT7468_REG_CFG5, data->cfg5);
 	} else {					/* Low freq. mode */
 		data->pwm_freq[nr] = FREQ_TO_REG(data->freq_map,
-						 FREQ_MAP_LEN, val);
+						 data->freq_map_size, val);
 		lm85_write_value(client, LM85_REG_AFAN_RANGE(nr),
 				 (data->zone[nr].range << 4)
 				 | data->pwm_freq[nr]);
@@ -1196,7 +1199,7 @@ static ssize_t set_temp_auto_temp_min(struct device *dev,
 		TEMP_FROM_REG(data->zone[nr].limit));
 	lm85_write_value(client, LM85_REG_AFAN_RANGE(nr),
 		((data->zone[nr].range & 0x0f) << 4)
-		| (data->pwm_freq[nr] & 0x07));
+		| data->pwm_freq[nr]);
 
 	mutex_unlock(&data->update_lock);
 	return count;
@@ -1232,7 +1235,7 @@ static ssize_t set_temp_auto_temp_max(struct device *dev,
 		val - min);
 	lm85_write_value(client, LM85_REG_AFAN_RANGE(nr),
 		((data->zone[nr].range & 0x0f) << 4)
-		| (data->pwm_freq[nr] & 0x07));
+		| data->pwm_freq[nr]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -1569,9 +1572,11 @@ static int lm85_probe(struct i2c_client *client, const struct i2c_device_id *id)
 	case emc6d103:
 	case emc6d103s:
 		data->freq_map = adm1027_freq_map;
+		data->freq_map_size = ARRAY_SIZE(adm1027_freq_map);
 		break;
 	default:
 		data->freq_map = lm85_freq_map;
+		data->freq_map_size = ARRAY_SIZE(lm85_freq_map);
 	}
 
 	/* Set the VRM version */
-- 
2.17.1


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 2/4] dt-bindings: Add LM96000 as a trivial device
  2019-02-04 20:19 [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support Jeremy Gebben
  2019-02-04 20:19 ` [PATCH v3 1/4] hwmon: (lm85) remove freq_map size hardcodes Jeremy Gebben
@ 2019-02-04 20:19 ` Jeremy Gebben
  2019-02-04 20:27   ` Rob Herring
  2019-02-04 20:19 ` [PATCH v3 3/4] hwmon: (lm85) support the LM96000 Jeremy Gebben
                   ` (2 subsequent siblings)
  4 siblings, 1 reply; 7+ messages in thread
From: Jeremy Gebben @ 2019-02-04 20:19 UTC (permalink / raw)
  To: Rob Herring, Mark Rutland, devicetree, Jean Delvare,
	Guenter Roeck, linux-hwmon, linux-kernel

The LM96000 is a temperature sensor and fan controller based
on the LM85.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
---
 Documentation/devicetree/bindings/trivial-devices.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
index cc64ec63a6ad..d79fb22bde39 100644
--- a/Documentation/devicetree/bindings/trivial-devices.yaml
+++ b/Documentation/devicetree/bindings/trivial-devices.yaml
@@ -322,6 +322,8 @@ properties:
           - ti,ads7830
             # Temperature Monitoring and Fan Control
           - ti,amc6821
+            # Temperature sensor with integrated fan control
+          - ti,lm96000
             # I2C Touch-Screen Controller
           - ti,tsc2003
             # Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface
-- 
2.17.1


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 3/4] hwmon: (lm85) support the LM96000
  2019-02-04 20:19 [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support Jeremy Gebben
  2019-02-04 20:19 ` [PATCH v3 1/4] hwmon: (lm85) remove freq_map size hardcodes Jeremy Gebben
  2019-02-04 20:19 ` [PATCH v3 2/4] dt-bindings: Add LM96000 as a trivial device Jeremy Gebben
@ 2019-02-04 20:19 ` Jeremy Gebben
  2019-02-04 20:19 ` [PATCH v3 4/4] hwmon: (lm85) add support for LM96000 high frequencies Jeremy Gebben
  2019-02-04 22:45 ` [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support Guenter Roeck
  4 siblings, 0 replies; 7+ messages in thread
From: Jeremy Gebben @ 2019-02-04 20:19 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, Jonathan Corbet, linux-hwmon,
	linux-doc, linux-kernel

It has been supported as a generic lm85 for quite some time.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
---
 Documentation/hwmon/lm85 | 6 +++++-
 drivers/hwmon/lm85.c     | 9 +++++++--
 2 files changed, 12 insertions(+), 3 deletions(-)

diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85
index 7c49feaa79d2..4f531f4acc3f 100644
--- a/Documentation/hwmon/lm85
+++ b/Documentation/hwmon/lm85
@@ -3,9 +3,13 @@ Kernel driver lm85
 
 Supported chips:
   * National Semiconductor LM85 (B and C versions)
-    Prefix: 'lm85'
+    Prefix: 'lm85b' or 'lm85c'
     Addresses scanned: I2C 0x2c, 0x2d, 0x2e
     Datasheet: http://www.national.com/pf/LM/LM85.html
+  * Texas Instruments LM96000
+    Prefix: 'lm9600'
+    Addresses scanned: I2C 0x2c, 0x2d, 0x2e
+    Datasheet: http://www.ti.com/lit/ds/symlink/lm96000.pdf
   * Analog Devices ADM1027
     Prefix: 'adm1027'
     Addresses scanned: I2C 0x2c, 0x2d, 0x2e
diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c
index 4b15193d195c..b23cf8e4c54b 100644
--- a/drivers/hwmon/lm85.c
+++ b/drivers/hwmon/lm85.c
@@ -41,7 +41,7 @@
 static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
 
 enum chips {
-	lm85,
+	lm85, lm96000,
 	adm1027, adt7463, adt7468,
 	emc6d100, emc6d102, emc6d103, emc6d103s
 };
@@ -1499,7 +1499,7 @@ static int lm85_detect(struct i2c_client *client, struct i2c_board_info *info)
 					"Found Winbond WPCD377I, ignoring\n");
 				return -ENODEV;
 			}
-			type_name = "lm85";
+			type_name = "lm96000";
 			break;
 		}
 	} else if (company == LM85_COMPANY_ANALOG_DEV) {
@@ -1623,6 +1623,7 @@ static const struct i2c_device_id lm85_id[] = {
 	{ "lm85", lm85 },
 	{ "lm85b", lm85 },
 	{ "lm85c", lm85 },
+	{ "lm96000", lm96000 },
 	{ "emc6d100", emc6d100 },
 	{ "emc6d101", emc6d100 },
 	{ "emc6d102", emc6d102 },
@@ -1657,6 +1658,10 @@ static const struct of_device_id lm85_of_match[] = {
 		.compatible = "national,lm85c",
 		.data = (void *)lm85
 	},
+	{
+		.compatible = "ti,lm96000",
+		.data = (void *)lm96000
+	},
 	{
 		.compatible = "smsc,emc6d100",
 		.data = (void *)emc6d100
-- 
2.17.1


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 4/4] hwmon: (lm85) add support for LM96000 high frequencies
  2019-02-04 20:19 [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support Jeremy Gebben
                   ` (2 preceding siblings ...)
  2019-02-04 20:19 ` [PATCH v3 3/4] hwmon: (lm85) support the LM96000 Jeremy Gebben
@ 2019-02-04 20:19 ` Jeremy Gebben
  2019-02-04 22:45 ` [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support Guenter Roeck
  4 siblings, 0 replies; 7+ messages in thread
From: Jeremy Gebben @ 2019-02-04 20:19 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, Jonathan Corbet, linux-hwmon,
	linux-doc, linux-kernel

The LM96000 expands the freqency field from 3 to 4 bits, to
add more frequencies in the 22.5 to 30 kHz ranges.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
---
 Documentation/hwmon/lm85 | 3 +++
 drivers/hwmon/lm85.c     | 9 +++++++++
 2 files changed, 12 insertions(+)

diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85
index 4f531f4acc3f..2329c383efe4 100644
--- a/Documentation/hwmon/lm85
+++ b/Documentation/hwmon/lm85
@@ -140,6 +140,9 @@ of voltage and temperature channels.
 SMSC EMC6D103S is similar to EMC6D103, but does not support pwm#_auto_pwm_minctl
 and temp#_auto_temp_off.
 
+The LM96000 supports additional high frequency PWM modes (22.5 kHz, 24 kHz,
+25.7 kHz, 27.7 kHz and 30 kHz), which can be configured on a per-PWM basis.
+
 Hardware Configurations
 -----------------------
 
diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c
index b23cf8e4c54b..a95d48316f06 100644
--- a/drivers/hwmon/lm85.c
+++ b/drivers/hwmon/lm85.c
@@ -202,6 +202,11 @@ static const int lm85_freq_map[] = { /* 1 Hz */
 	10, 15, 23, 30, 38, 47, 61, 94
 };
 
+static const int lm96000_freq_map[] = { /* 1 Hz */
+	10, 15, 23, 30, 38, 47, 61, 94,
+	22500, 24000, 25700, 25700, 27700, 27700, 30000, 30000
+};
+
 static const int adm1027_freq_map[] = { /* 1 Hz */
 	11, 15, 22, 29, 35, 44, 59, 88
 };
@@ -1574,6 +1579,10 @@ static int lm85_probe(struct i2c_client *client, const struct i2c_device_id *id)
 		data->freq_map = adm1027_freq_map;
 		data->freq_map_size = ARRAY_SIZE(adm1027_freq_map);
 		break;
+	case lm96000:
+		data->freq_map = lm96000_freq_map;
+		data->freq_map_size = ARRAY_SIZE(lm96000_freq_map);
+		break;
 	default:
 		data->freq_map = lm85_freq_map;
 		data->freq_map_size = ARRAY_SIZE(lm85_freq_map);
-- 
2.17.1


^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v3 2/4] dt-bindings: Add LM96000 as a trivial device
  2019-02-04 20:19 ` [PATCH v3 2/4] dt-bindings: Add LM96000 as a trivial device Jeremy Gebben
@ 2019-02-04 20:27   ` Rob Herring
  0 siblings, 0 replies; 7+ messages in thread
From: Rob Herring @ 2019-02-04 20:27 UTC (permalink / raw)
  To: Jeremy Gebben
  Cc: Mark Rutland, devicetree, Jean Delvare, Guenter Roeck,
	Linux HWMON List, linux-kernel

On Mon, Feb 4, 2019 at 2:19 PM Jeremy Gebben <jgebben@sweptlaser.com> wrote:
>
> The LM96000 is a temperature sensor and fan controller based
> on the LM85.
>
> Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
> ---
>  Documentation/devicetree/bindings/trivial-devices.yaml | 2 ++
>  1 file changed, 2 insertions(+)

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support
  2019-02-04 20:19 [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support Jeremy Gebben
                   ` (3 preceding siblings ...)
  2019-02-04 20:19 ` [PATCH v3 4/4] hwmon: (lm85) add support for LM96000 high frequencies Jeremy Gebben
@ 2019-02-04 22:45 ` Guenter Roeck
  4 siblings, 0 replies; 7+ messages in thread
From: Guenter Roeck @ 2019-02-04 22:45 UTC (permalink / raw)
  To: Jeremy Gebben; +Cc: Jean Delvare, linux-hwmon, linux-kernel

On Mon, Feb 04, 2019 at 01:19:02PM -0700, Jeremy Gebben wrote:
> Hi,
> 
> This patch set adds support for the PWM frequencies from 22.5 to 30 kHz
> available on the LM96000.
> 
> It looks like this chip has been supported for a long time, but wasn't
> mentioned in the docs (which I have updated).
> 
> I stumbled on to a 10 year old thread discussing a patch which looks
> like an early attempt to add support for this chip, which may be of
> interest:
> https://lm-sensors.lm-sensors.narkive.com/1SIwaMDT/patch-hwmon-lm96000-support
> 

Series applied to hwmon-next.

Thanks,
Guenter

^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, back to index

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-02-04 20:19 [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support Jeremy Gebben
2019-02-04 20:19 ` [PATCH v3 1/4] hwmon: (lm85) remove freq_map size hardcodes Jeremy Gebben
2019-02-04 20:19 ` [PATCH v3 2/4] dt-bindings: Add LM96000 as a trivial device Jeremy Gebben
2019-02-04 20:27   ` Rob Herring
2019-02-04 20:19 ` [PATCH v3 3/4] hwmon: (lm85) support the LM96000 Jeremy Gebben
2019-02-04 20:19 ` [PATCH v3 4/4] hwmon: (lm85) add support for LM96000 high frequencies Jeremy Gebben
2019-02-04 22:45 ` [PATCH v3 0/4] hwmon: (lm85) add LM96000 high freqency pwm support Guenter Roeck

Linux-Hwmon Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-hwmon/0 linux-hwmon/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-hwmon linux-hwmon/ https://lore.kernel.org/linux-hwmon \
		linux-hwmon@vger.kernel.org linux-hwmon@archiver.kernel.org
	public-inbox-index linux-hwmon


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-hwmon


AGPL code for this site: git clone https://public-inbox.org/ public-inbox