Linux-Hwmon Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v3 2/2] hwmon: Add driver for Texas Instruments TMP512/513 sensor chips
@ 2019-10-03 18:34 Tremblay, Eric
  2019-10-04 15:13 ` Guenter Roeck
  0 siblings, 1 reply; 2+ messages in thread
From: Tremblay, Eric @ 2019-10-03 18:34 UTC (permalink / raw)
  To: linux-hwmon

hwmon: Add DT bindings for TMP513 driver

Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
---
 .../devicetree/bindings/hwmon/tmp513.txt      | 33 +++++++++++++++++++
 1 file changed, 33 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/hwmon/tmp513.txt

diff --git a/Documentation/devicetree/bindings/hwmon/tmp513.txt b/Documentation/devicetree/bindings/hwmon/tmp513.txt
new file mode 100644
index 000000000000..341c764e9173
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/tmp513.txt
@@ -0,0 +1,33 @@
+TMP513 system monitor sensor
+-------------------------
+
+Require node properties:
+- compatible: one of
+		"ti,tmp512"
+		"ti,tmp513"
+- reg : the I2C address of the device. This is 0x5c, 0x5d, 0x5e, or 0x5f.
+
+Optional properties:
+- shunt-resistor-uohm : The shunt resistor value in uOhm. If 0, the calibration process
+		will be skiped and the current and power measurement engine will not work.
+		Temperature and voltage measurement will continue to work. The shunt value also
+		need to respect : rshunt <= pga-gain * 40 * 1000 * 1000. If not, it's not possible
+		to compute a valid calibration value.
+- bus-voltage-range: 32V or 16V, default to 32V.
+- pga-gain: The gain value for the PGA function. This is 8, 4, 2 or 1. Default to 8.
+- temp_2_nfactor: nFactor for remote channel 1. Value according to Table 11 in datasheet.
+- temp_3_nfactor: nFactor for remote channel 2. Value according to Table 11 in datasheet.
+- temp_4_nfactor: nFactor for remote channel 3. Value according to Table 11 in datasheet,
+		TMP513 only.
+
+Example:
+	tmp513@5c {
+		  compatible = "ti,tmp513";
+		  reg = <0x5C>;
+		  shunt-resistor-uohm = <330000>;
+		  bus-voltage-range = <32>;
+		  pga-gain = <8>;
+		  temp_2_nfactor = <0x01>;
+		  temp_3_nfactor = <0x02>;
+		  temp_4_nfactor = <0x03>;
+	};
-- 
2.17.1


^ permalink raw reply	[flat|nested] 2+ messages in thread

* Re: [PATCH v3 2/2] hwmon: Add driver for Texas Instruments TMP512/513 sensor chips
  2019-10-03 18:34 [PATCH v3 2/2] hwmon: Add driver for Texas Instruments TMP512/513 sensor chips Tremblay, Eric
@ 2019-10-04 15:13 ` Guenter Roeck
  0 siblings, 0 replies; 2+ messages in thread
From: Guenter Roeck @ 2019-10-04 15:13 UTC (permalink / raw)
  To: Tremblay, Eric; +Cc: linux-hwmon

On Thu, Oct 03, 2019 at 06:34:41PM +0000, Tremblay, Eric wrote:
> hwmon: Add DT bindings for TMP513 driver
> 
$subject is misleading.

> Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
> ---
>  .../devicetree/bindings/hwmon/tmp513.txt      | 33 +++++++++++++++++++
>  1 file changed, 33 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/hwmon/tmp513.txt
> 
> diff --git a/Documentation/devicetree/bindings/hwmon/tmp513.txt b/Documentation/devicetree/bindings/hwmon/tmp513.txt
> new file mode 100644
> index 000000000000..341c764e9173
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/tmp513.txt
> @@ -0,0 +1,33 @@
> +TMP513 system monitor sensor
> +-------------------------
> +
> +Require node properties:
> +- compatible: one of
> +		"ti,tmp512"
> +		"ti,tmp513"
> +- reg : the I2C address of the device. This is 0x5c, 0x5d, 0x5e, or 0x5f.
> +
> +Optional properties:
> +- shunt-resistor-uohm : The shunt resistor value in uOhm. If 0, the calibration process
> +		will be skiped and the current and power measurement engine will not work.
> +		Temperature and voltage measurement will continue to work. The shunt value also
> +		need to respect : rshunt <= pga-gain * 40 * 1000 * 1000. If not, it's not possible
> +		to compute a valid calibration value.

If this is not mandatory, I would suggest to declare a sensible default,
such as 1 mOhm / 1000 uOhm.

> +- bus-voltage-range: 32V or 16V, default to 32V.

Question for Rob: Does this need "-volt" as part of the name ?

> +- pga-gain: The gain value for the PGA function. This is 8, 4, 2 or 1. Default to 8.

It might be useful to explain "pga".

> +- temp_2_nfactor: nFactor for remote channel 1. Value according to Table 11 in datasheet.
> +- temp_3_nfactor: nFactor for remote channel 2. Value according to Table 11 in datasheet.
> +- temp_4_nfactor: nFactor for remote channel 3. Value according to Table 11 in datasheet,

Maybe an array and temp-nfactor, with 0x0 meaning "use default" ?

> +		TMP513 only.
> +
> +Example:
> +	tmp513@5c {
> +		  compatible = "ti,tmp513";
> +		  reg = <0x5C>;
> +		  shunt-resistor-uohm = <330000>;
> +		  bus-voltage-range = <32>;
> +		  pga-gain = <8>;
> +		  temp_2_nfactor = <0x01>;
> +		  temp_3_nfactor = <0x02>;
> +		  temp_4_nfactor = <0x03>;
> +	};
> -- 
> 2.17.1
> 

^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, back to index

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-03 18:34 [PATCH v3 2/2] hwmon: Add driver for Texas Instruments TMP512/513 sensor chips Tremblay, Eric
2019-10-04 15:13 ` Guenter Roeck

Linux-Hwmon Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-hwmon/0 linux-hwmon/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-hwmon linux-hwmon/ https://lore.kernel.org/linux-hwmon \
		linux-hwmon@vger.kernel.org
	public-inbox-index linux-hwmon

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-hwmon


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git