From: Jeff LaBundy <jeff@labundy.com>
To: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: lee.jones@linaro.org, jdelvare@suse.com, linux@roeck-us.net,
thierry.reding@gmail.com, jic23@kernel.org,
devicetree@vger.kernel.org, linux-input@vger.kernel.org,
linux-hwmon@vger.kernel.org, u.kleine-koenig@pengutronix.de,
linux-pwm@vger.kernel.org, knaack.h@gmx.de, lars@metafoo.de,
pmeerw@pmeerw.net, linux-iio@vger.kernel.org, robh+dt@kernel.org,
mark.rutland@arm.com
Subject: Re: [PATCH 3/8] input: keyboard: Add support for Azoteq IQS620A/621/622/624/625
Date: Tue, 22 Oct 2019 20:29:13 -0500 [thread overview]
Message-ID: <20191023012913.GA3233@labundy.com> (raw)
In-Reply-To: <20191023002254.GW35946@dtor-ws>
Hi Dmitry,
Thank you for your prompt review.
On Tue, Oct 22, 2019 at 05:22:54PM -0700, Dmitry Torokhov wrote:
> Hi Jeff,
>
> On Sun, Oct 20, 2019 at 11:11:18PM -0500, Jeff LaBundy wrote:
> > This patch adds touch key support for six-channel members of the
> > Azoteq ProxFusion family of sensor devices.
> >
> > Signed-off-by: Jeff LaBundy <jeff@labundy.com>
> > ---
> > drivers/input/keyboard/Kconfig | 10 ++
> > drivers/input/keyboard/Makefile | 1 +
> > drivers/input/keyboard/iqs62x-keys.c | 340 +++++++++++++++++++++++++++++++++++
> > 3 files changed, 351 insertions(+)
> > create mode 100644 drivers/input/keyboard/iqs62x-keys.c
> >
> > diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
> > index 8911bc2..ab10aff 100644
> > --- a/drivers/input/keyboard/Kconfig
> > +++ b/drivers/input/keyboard/Kconfig
> > @@ -657,6 +657,16 @@ config KEYBOARD_IPAQ_MICRO
> > To compile this driver as a module, choose M here: the
> > module will be called ipaq-micro-keys.
> >
> > +config KEYBOARD_IQS62X
> > + tristate "Azoteq IQS620A/621/622/624/625 touch keys"
> > + depends on MFD_IQS62X
> > + help
> > + Say Y here to enable touch-key support for six-channel members of
> > + the Azoteq ProxFusion family of sensor devices.
> > +
> > + To compile this driver as a module, choose M here: the module will
> > + be called iqs62x-keys.
> > +
> > config KEYBOARD_OMAP
> > tristate "TI OMAP keypad support"
> > depends on ARCH_OMAP1
> > diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
> > index 9510325..ee85b7f 100644
> > --- a/drivers/input/keyboard/Makefile
> > +++ b/drivers/input/keyboard/Makefile
> > @@ -28,6 +28,7 @@ obj-$(CONFIG_KEYBOARD_TCA8418) += tca8418_keypad.o
> > obj-$(CONFIG_KEYBOARD_HIL) += hil_kbd.o
> > obj-$(CONFIG_KEYBOARD_HIL_OLD) += hilkbd.o
> > obj-$(CONFIG_KEYBOARD_IPAQ_MICRO) += ipaq-micro-keys.o
> > +obj-$(CONFIG_KEYBOARD_IQS62X) += iqs62x-keys.o
> > obj-$(CONFIG_KEYBOARD_IMX) += imx_keypad.o
> > obj-$(CONFIG_KEYBOARD_HP6XX) += jornada680_kbd.o
> > obj-$(CONFIG_KEYBOARD_HP7XX) += jornada720_kbd.o
> > diff --git a/drivers/input/keyboard/iqs62x-keys.c b/drivers/input/keyboard/iqs62x-keys.c
> > new file mode 100644
> > index 0000000..9d929f1
> > --- /dev/null
> > +++ b/drivers/input/keyboard/iqs62x-keys.c
> > @@ -0,0 +1,340 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Azoteq IQS620A/621/622/624/625 Touch Keys
> > + *
> > + * Copyright (C) 2019
> > + * Author: Jeff LaBundy <jeff@labundy.com>
> > + */
> > +
> > +#include <linux/device.h>
> > +#include <linux/input.h>
> > +#include <linux/kernel.h>
> > +#include <linux/mfd/iqs62x.h>
> > +#include <linux/module.h>
> > +#include <linux/notifier.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/slab.h>
> > +
> > +enum {
> > + IQS62X_SW_HALL_N,
> > + IQS62X_SW_HALL_S,
> > +};
> > +
> > +static const char * const iqs62x_switch_names[] = {
> > + [IQS62X_SW_HALL_N] = "hall_switch_north",
> > + [IQS62X_SW_HALL_S] = "hall_switch_south",
> > +};
> > +
> > +struct iqs62x_switch_desc {
> > + enum iqs62x_event_flag flag;
> > + unsigned int code;
> > + bool enabled;
> > +};
> > +
> > +struct iqs62x_keys_private {
> > + struct iqs62x_core *iqs62x;
> > + struct input_dev *input;
> > + struct notifier_block notifier;
> > + struct iqs62x_switch_desc switches[ARRAY_SIZE(iqs62x_switch_names)];
> > + unsigned int keycode[IQS62X_NUM_KEYS];
> > + unsigned int keycodemax;
> > + u8 interval;
> > +};
> > +
> > +static int iqs62x_keys_parse_prop(struct platform_device *pdev,
> > + struct iqs62x_keys_private *iqs62x_keys)
> > +{
> > + struct device_node *keys_node = pdev->dev.of_node;
> > + struct device_node *hall_node;
> > + unsigned int val;
> > + int ret, i;
> > +
> > + if (!keys_node)
> > + return 0;
> > +
> > + ret = of_property_read_variable_u32_array(keys_node, "linux,keycodes",
> > + iqs62x_keys->keycode, 0,
> > + IQS62X_NUM_KEYS);
>
> I do not think this has to be OF-specific, so please use
> device_property_*() API.
>
Sure thing; will do.
> > + if (ret < 0) {
> > + dev_err(&pdev->dev, "Failed to read keycodes: %d\n", ret);
> > + return ret;
> > + }
> > + iqs62x_keys->keycodemax = ret;
> > +
> > + for (i = 0; i < ARRAY_SIZE(iqs62x_keys->switches); i++) {
> > + hall_node = of_get_child_by_name(keys_node,
> > + iqs62x_switch_names[i]);
> > + if (!hall_node)
> > + continue;
> > +
> > + ret = of_property_read_u32(hall_node, "linux,code", &val);
> > + if (ret < 0) {
> > + dev_err(&pdev->dev, "Failed to read switch code: %d\n",
> > + ret);
> > + of_node_put(hall_node);
> > + return ret;
> > + }
> > +
> > + if (of_property_read_bool(hall_node, "azoteq,use-prox"))
> > + iqs62x_keys->switches[i].flag = (i == IQS62X_SW_HALL_N ?
> > + IQS62X_EVENT_HALL_N_P :
> > + IQS62X_EVENT_HALL_S_P);
> > + else
> > + iqs62x_keys->switches[i].flag = (i == IQS62X_SW_HALL_N ?
> > + IQS62X_EVENT_HALL_N_T :
> > + IQS62X_EVENT_HALL_S_T);
> > +
> > + iqs62x_keys->switches[i].code = val;
> > + iqs62x_keys->switches[i].enabled = true;
> > +
> > + of_node_put(hall_node);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int iqs62x_keys_init(struct iqs62x_keys_private *iqs62x_keys)
> > +{
> > + struct iqs62x_core *iqs62x = iqs62x_keys->iqs62x;
> > + enum iqs62x_event_flag flag;
> > + unsigned int event_mask_reg;
> > + unsigned int event_mask = 0;
> > + unsigned int val;
> > + int error, i;
> > +
> > + switch (iqs62x->dev_desc->prod_num) {
> > + case IQS620_PROD_NUM:
> > + case IQS621_PROD_NUM:
> > + case IQS622_PROD_NUM:
> > + event_mask_reg = IQS620_GLBL_EVENT_MASK;
> > +
> > + /*
> > + * Discreet button, hysteresis and SAR UI flags represent keys
> > + * and are unmasked if mapped to a valid keycode.
> > + */
> > + for (i = 0; i < iqs62x_keys->keycodemax; i++) {
> > + if (iqs62x_keys->keycode[i] == KEY_RESERVED)
> > + continue;
> > +
> > + if (iqs62x_events[i].reg == IQS62X_EVENT_PROX)
> > + event_mask |= iqs62x->dev_desc->prox_mask;
> > + else if (iqs62x_events[i].reg == IQS62X_EVENT_HYST)
> > + event_mask |= (iqs62x->dev_desc->hyst_mask |
> > + iqs62x->dev_desc->sar_mask);
> > + }
> > +
> > + error = regmap_read(iqs62x->map, iqs62x->dev_desc->hall_flags,
> > + &val);
> > + if (error)
> > + return error;
> > +
> > + /*
> > + * Hall UI flags represent switches and are unmasked if their
> > + * corresponding child nodes are present.
> > + */
> > + for (i = 0; i < ARRAY_SIZE(iqs62x_keys->switches); i++) {
> > + if (!(iqs62x_keys->switches[i].enabled))
> > + continue;
> > +
> > + flag = iqs62x_keys->switches[i].flag;
> > +
> > + if (iqs62x_events[flag].reg != IQS62X_EVENT_HALL)
> > + continue;
> > +
> > + event_mask |= iqs62x->dev_desc->hall_mask;
> > +
> > + input_report_switch(iqs62x_keys->input,
> > + iqs62x_keys->switches[i].code,
> > + (val & iqs62x_events[flag].mask) ==
> > + iqs62x_events[flag].val);
> > + }
> > +
> > + input_sync(iqs62x_keys->input);
> > + break;
> > +
> > + case IQS624_PROD_NUM:
> > + event_mask_reg = IQS624_HALL_UI;
> > +
> > + /*
> > + * Interval change events represent keys and are unmasked if
> > + * either wheel movement flag is mapped to a valid keycode.
> > + */
> > + if (iqs62x_keys->keycode[IQS62X_EVENT_WHEEL_UP] != KEY_RESERVED)
> > + event_mask |= IQS624_HALL_UI_INT_EVENT;
> > +
> > + if (iqs62x_keys->keycode[IQS62X_EVENT_WHEEL_DN] != KEY_RESERVED)
> > + event_mask |= IQS624_HALL_UI_INT_EVENT;
> > +
> > + error = regmap_read(iqs62x->map, iqs62x->dev_desc->interval,
> > + &val);
> > + if (error)
> > + return error;
> > +
> > + iqs62x_keys->interval = val;
> > + break;
> > +
> > + default:
> > + return 0;
> > + }
> > +
> > + return regmap_update_bits(iqs62x->map, event_mask_reg, event_mask, 0);
> > +}
> > +
> > +static int iqs62x_keys_notifier(struct notifier_block *notifier,
> > + unsigned long event_flags, void *context)
> > +{
> > + struct iqs62x_event_data *event_data = context;
> > + struct iqs62x_keys_private *iqs62x_keys;
> > + int error, i;
> > +
> > + iqs62x_keys = container_of(notifier, struct iqs62x_keys_private,
> > + notifier);
> > +
> > + if (event_flags & BIT(IQS62X_EVENT_SYS_RESET)) {
> > + error = iqs62x_keys_init(iqs62x_keys);
> > + if (error) {
> > + dev_err(iqs62x_keys->input->dev.parent,
> > + "Failed to re-initialize device: %d\n", error);
> > + return NOTIFY_BAD;
> > + }
> > +
> > + return NOTIFY_OK;
> > + }
> > +
> > + for (i = 0; i < iqs62x_keys->keycodemax; i++) {
> > + if (iqs62x_events[i].reg == IQS62X_EVENT_WHEEL &&
> > + event_data->interval == iqs62x_keys->interval)
> > + continue;
> > +
> > + input_report_key(iqs62x_keys->input, iqs62x_keys->keycode[i],
> > + event_flags & BIT(i));
> > + }
> > +
> > + for (i = 0; i < ARRAY_SIZE(iqs62x_keys->switches); i++)
> > + if (iqs62x_keys->switches[i].enabled)
> > + input_report_switch(iqs62x_keys->input,
> > + iqs62x_keys->switches[i].code,
> > + event_flags &
> > + BIT(iqs62x_keys->switches[i].flag));
> > +
> > + input_sync(iqs62x_keys->input);
> > +
> > + if (event_data->interval == iqs62x_keys->interval)
> > + return NOTIFY_OK;
> > +
> > + /*
> > + * Each frame contains at most one wheel event (up or down), in which
> > + * case a full keystroke is emulated.
> > + */
> > + if (event_flags & BIT(IQS62X_EVENT_WHEEL_UP)) {
> > + input_report_key(iqs62x_keys->input,
> > + iqs62x_keys->keycode[IQS62X_EVENT_WHEEL_UP],
> > + 0);
> > + input_sync(iqs62x_keys->input);
> > + } else if (event_flags & BIT(IQS62X_EVENT_WHEEL_DN)) {
> > + input_report_key(iqs62x_keys->input,
> > + iqs62x_keys->keycode[IQS62X_EVENT_WHEEL_DN],
> > + 0);
>
> Not '1'?
>
We pick up the '1' in the first of the two for loops above so long as the wheel
moved "enough." In this case (and this case only), a subsequent '0' is sent to
emulate a full press/release cycle (2 * {EV_KEY + EV_SYN}) for wheel "ticks."
I will update the comment to say "...in which case a complementary release cycle
is emulated." If I have misunderstood your concern, please let me know.
> > + input_sync(iqs62x_keys->input);
> > + }
> > +
> > + iqs62x_keys->interval = event_data->interval;
> > +
> > + return NOTIFY_OK;
> > +}
> > +
> > +static int iqs62x_keys_probe(struct platform_device *pdev)
> > +{
> > + struct iqs62x_core *iqs62x = dev_get_drvdata(pdev->dev.parent);
> > + struct iqs62x_keys_private *iqs62x_keys;
> > + struct input_dev *input;
> > + int error, i;
> > +
> > + iqs62x_keys = devm_kzalloc(&pdev->dev, sizeof(*iqs62x_keys),
> > + GFP_KERNEL);
> > + if (!iqs62x_keys)
> > + return -ENOMEM;
> > +
> > + platform_set_drvdata(pdev, iqs62x_keys);
> > +
> > + error = iqs62x_keys_parse_prop(pdev, iqs62x_keys);
> > + if (error)
> > + return error;
> > +
> > + input = devm_input_allocate_device(&pdev->dev);
> > + if (!input)
> > + return -ENOMEM;
> > +
> > + input->keycodemax = iqs62x_keys->keycodemax;
> > + input->keycode = iqs62x_keys->keycode;
> > + input->keycodesize = sizeof(*iqs62x_keys->keycode);
> > +
> > + input->name = iqs62x->dev_desc->dev_name;
> > + input->id.bustype = BUS_I2C;
> > +
> > + __set_bit(EV_KEY, input->evbit);
> > +
> > + for (i = 0; i < iqs62x_keys->keycodemax; i++)
> > + __set_bit(iqs62x_keys->keycode[i], input->keybit);
> > +
> > + __clear_bit(KEY_RESERVED, input->keybit);
> > +
> > + for (i = 0; i < ARRAY_SIZE(iqs62x_keys->switches); i++)
> > + if (iqs62x_keys->switches[i].enabled) {
> > + __set_bit(EV_SW, input->evbit);
> > + __set_bit(iqs62x_keys->switches[i].code, input->swbit);
> > + }
> > +
> > + iqs62x_keys->iqs62x = iqs62x;
> > + iqs62x_keys->input = input;
> > +
> > + error = iqs62x_keys_init(iqs62x_keys);
> > + if (error) {
> > + dev_err(&pdev->dev, "Failed to initialize device: %d\n", error);
> > + return error;
> > + }
> > +
> > + error = input_register_device(iqs62x_keys->input);
> > + if (error) {
> > + dev_err(&pdev->dev, "Failed to register device: %d\n", error);
> > + return error;
> > + }
> > +
> > + iqs62x_keys->notifier.notifier_call = iqs62x_keys_notifier;
> > + error = blocking_notifier_chain_register(&iqs62x_keys->iqs62x->nh,
> > + &iqs62x_keys->notifier);
> > + if (error)
> > + dev_err(&pdev->dev, "Failed to register notifier: %d\n", error);
> > +
> > + return error;
> > +}
> > +
> > +static int iqs62x_keys_remove(struct platform_device *pdev)
> > +{
> > + struct iqs62x_keys_private *iqs62x_keys = platform_get_drvdata(pdev);
> > + int error;
> > +
> > + error = blocking_notifier_chain_unregister(&iqs62x_keys->iqs62x->nh,
> > + &iqs62x_keys->notifier);
> > + if (error)
> > + dev_err(&pdev->dev,
> > + "Failed to unregister notifier: %d\n", error);
> > +
> > + return error;
> > +}
> > +
> > +static struct platform_driver iqs62x_keys_platform_driver = {
> > + .driver = {
> > + .name = IQS62X_DRV_NAME_KEYS,
> > + },
> > + .probe = iqs62x_keys_probe,
> > + .remove = iqs62x_keys_remove,
> > +};
> > +module_platform_driver(iqs62x_keys_platform_driver);
> > +
> > +MODULE_AUTHOR("Jeff LaBundy <jeff@labundy.com>");
> > +MODULE_DESCRIPTION("Azoteq IQS620A/621/622/624/625 Touch Keys");
> > +MODULE_LICENSE("GPL");
> > +MODULE_ALIAS("platform:" IQS62X_DRV_NAME_KEYS);
> > --
> > 2.7.4
> >
>
> Thanks.
>
> --
> Dmitry
>
Kind regards,
Jeff LaBundy
next prev parent reply other threads:[~2019-10-23 1:29 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-21 4:11 [PATCH 0/8] Add support for Azoteq IQS620A/621/622/624/625 Jeff LaBundy
2019-10-21 4:11 ` [PATCH 1/8] dt-bindings: mfd: iqs62x: Add bindings Jeff LaBundy
2019-10-22 11:00 ` Jonathan Cameron
2019-10-23 3:36 ` Jeff LaBundy
2019-10-23 9:30 ` Lee Jones
2019-10-24 2:38 ` Jeff LaBundy
2019-10-21 4:11 ` [PATCH 2/8] mfd: Add support for Azoteq IQS620A/621/622/624/625 Jeff LaBundy
2019-10-31 13:44 ` Lee Jones
2019-10-31 18:42 ` Dmitry Torokhov
2019-11-01 4:59 ` Jeff LaBundy
2019-11-01 8:56 ` Lee Jones
2019-11-02 2:49 ` Jeff LaBundy
2019-10-21 4:11 ` [PATCH 3/8] input: keyboard: " Jeff LaBundy
2019-10-23 0:22 ` Dmitry Torokhov
2019-10-23 1:29 ` Jeff LaBundy [this message]
2019-10-23 23:08 ` Dmitry Torokhov
2019-10-21 4:11 ` [PATCH 4/8] hwmon: Add support for Azoteq IQS620AT temperature sensor Jeff LaBundy
2019-10-21 15:38 ` Guenter Roeck
2019-10-22 2:26 ` Jeff LaBundy
2019-10-22 3:22 ` Guenter Roeck
2019-10-22 11:38 ` Jonathan Cameron
2019-10-23 2:04 ` Jeff LaBundy
2019-10-21 4:11 ` [PATCH 5/8] pwm: Add support for Azoteq IQS620A PWM generator Jeff LaBundy
2019-10-21 7:34 ` Uwe Kleine-König
2019-10-22 4:36 ` Jeff LaBundy
2019-10-22 6:54 ` Uwe Kleine-König
2019-10-23 2:45 ` Jeff LaBundy
2019-10-23 7:23 ` Uwe Kleine-König
2019-10-24 3:02 ` Jeff LaBundy
2019-10-21 4:11 ` [PATCH 6/8] iio: light: Add support for Azoteq IQS621 ambient light sensor Jeff LaBundy
2019-10-22 11:23 ` Jonathan Cameron
2019-10-23 2:59 ` Jeff LaBundy
2019-10-21 4:11 ` [PATCH 7/8] iio: proximity: Add support for Azoteq IQS622 proximity sensor Jeff LaBundy
2019-10-22 11:23 ` Jonathan Cameron
2019-10-23 3:09 ` Jeff LaBundy
2019-10-21 4:11 ` [PATCH 8/8] iio: position: Add support for Azoteq IQS624/625 angle sensor Jeff LaBundy
2019-10-22 11:28 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191023012913.GA3233@labundy.com \
--to=jeff@labundy.com \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.torokhov@gmail.com \
--cc=jdelvare@suse.com \
--cc=jic23@kernel.org \
--cc=knaack.h@gmx.de \
--cc=lars@metafoo.de \
--cc=lee.jones@linaro.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-pwm@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=mark.rutland@arm.com \
--cc=pmeerw@pmeerw.net \
--cc=robh+dt@kernel.org \
--cc=thierry.reding@gmail.com \
--cc=u.kleine-koenig@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).