Linux-Hwmon Archive on lore.kernel.org
 help / color / Atom feed
From: Tao Ren <rentao.bupt@gmail.com>
To: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>,
	Jonathan Corbet <corbet@lwn.net>,
	linux-hwmon@vger.kernel.org, linux-doc@vger.kernel.org,
	linux-kernel@vger.kernel.org, openbmc@lists.ozlabs.org,
	taoren@fb.com
Subject: Re: [PATCH v2 2/2] docs: hwmon: Document bel-pfe pmbus driver
Date: Sat, 2 Nov 2019 21:44:52 -0700
Message-ID: <20191103044432.GA3364@taoren-ubuntu-R90MNF91> (raw)
In-Reply-To: <20191102153115.GA5205@roeck-us.net>

On Sat, Nov 02, 2019 at 08:31:15AM -0700, Guenter Roeck wrote:
> On Tue, Oct 29, 2019 at 11:20:54AM -0700, rentao.bupt@gmail.com wrote:
> > From: Tao Ren <rentao.bupt@gmail.com>
> > 
> > Add documentation for bel-pfe pmbus driver which supports BEL PFE1100 and
> > PFE3000 power supplies.
> > 
> > Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
> 
> Applied after adding bel-pfe to index.rst.
> 
> Thanks,
> Guenter

Thank you Guenter. I didn't know index.rst needs to be updated; will
do it for my future doc patches.


Cheers,

Tao

> > ---
> >  No change in v2.
> > 
> >  Documentation/hwmon/bel-pfe.rst | 112 ++++++++++++++++++++++++++++++++
> >  1 file changed, 112 insertions(+)
> >  create mode 100644 Documentation/hwmon/bel-pfe.rst
> > 
> > diff --git a/Documentation/hwmon/bel-pfe.rst b/Documentation/hwmon/bel-pfe.rst
> > new file mode 100644
> > index 000000000000..4b4a7d67854c
> > --- /dev/null
> > +++ b/Documentation/hwmon/bel-pfe.rst
> > @@ -0,0 +1,112 @@
> > +Kernel driver bel-pfe
> > +======================
> > +
> > +Supported chips:
> > +
> > +  * BEL PFE1100
> > +
> > +    Prefixes: 'pfe1100'
> > +
> > +    Addresses scanned: -
> > +
> > +    Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe1100-12-054xa.pdf
> > +
> > +  * BEL PFE3000
> > +
> > +    Prefixes: 'pfe3000'
> > +
> > +    Addresses scanned: -
> > +
> > +    Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe3000-series.pdf
> > +
> > +Author: Tao Ren <rentao.bupt@gmail.com>
> > +
> > +
> > +Description
> > +-----------
> > +
> > +This driver supports hardware monitoring for below power supply devices
> > +which support PMBus Protocol:
> > +
> > +  * BEL PFE1100
> > +
> > +    1100 Watt AC to DC power-factor-corrected (PFC) power supply.
> > +    PMBus Communication Manual is not publicly available.
> > +
> > +  * BEL PFE3000
> > +
> > +    3000 Watt AC/DC power-factor-corrected (PFC) and DC-DC power supply.
> > +    PMBus Communication Manual is not publicly available.
> > +
> > +The driver is a client driver to the core PMBus driver. Please see
> > +Documentation/hwmon/pmbus.rst for details on PMBus client drivers.
> > +
> > +
> > +Usage Notes
> > +-----------
> > +
> > +This driver does not auto-detect devices. You will have to instantiate the
> > +devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for
> > +details.
> > +
> > +Example: the following will load the driver for an PFE3000 at address 0x20
> > +on I2C bus #1::
> > +
> > +	$ modprobe bel-pfe
> > +	$ echo pfe3000 0x20 > /sys/bus/i2c/devices/i2c-1/new_device
> > +
> > +
> > +Platform data support
> > +---------------------
> > +
> > +The driver supports standard PMBus driver platform data.
> > +
> > +
> > +Sysfs entries
> > +-------------
> > +
> > +======================= =======================================================
> > +curr1_label		"iin"
> > +curr1_input		Measured input current
> > +curr1_max               Input current max value
> > +curr1_max_alarm         Input current max alarm
> > +
> > +curr[2-3]_label		"iout[1-2]"
> > +curr[2-3]_input		Measured output current
> > +curr[2-3]_max           Output current max value
> > +curr[2-3]_max_alarm     Output current max alarm
> > +
> > +fan[1-2]_input          Fan 1 and 2 speed in RPM
> > +fan1_target             Set fan speed reference for both fans
> > +
> > +in1_label		"vin"
> > +in1_input		Measured input voltage
> > +in1_crit		Input voltage critical max value
> > +in1_crit_alarm		Input voltage critical max alarm
> > +in1_lcrit               Input voltage critical min value
> > +in1_lcrit_alarm         Input voltage critical min alarm
> > +in1_max                 Input voltage max value
> > +in1_max_alarm           Input voltage max alarm
> > +
> > +in2_label               "vcap"
> > +in2_input               Hold up capacitor voltage
> > +
> > +in[3-8]_label		"vout[1-3,5-7]"
> > +in[3-8]_input		Measured output voltage
> > +in[3-4]_alarm           vout[1-2] output voltage alarm
> > +
> > +power[1-2]_label	"pin[1-2]"
> > +power[1-2]_input        Measured input power
> > +power[1-2]_alarm	Input power high alarm
> > +
> > +power[3-4]_label	"pout[1-2]"
> > +power[3-4]_input	Measured output power
> > +
> > +temp[1-3]_input		Measured temperature
> > +temp[1-3]_alarm         Temperature alarm
> > +======================= =======================================================
> > +
> > +.. note::
> > +
> > +    - curr3, fan2, vout[2-7], vcap, pin2, pout2 and temp3 attributes only
> > +      exist for PFE3000.

  reply index

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-29 18:20 [PATCH v2 0/2] hwmon: (pmbus) add driver for BEL PFE1100 and PFE3000 rentao.bupt
2019-10-29 18:20 ` [PATCH v2 1/2] " rentao.bupt
2019-11-02 15:18   ` Guenter Roeck
2019-10-29 18:20 ` [PATCH v2 2/2] docs: hwmon: Document bel-pfe pmbus driver rentao.bupt
2019-11-02 15:31   ` Guenter Roeck
2019-11-03  4:44     ` Tao Ren [this message]
2019-11-03  4:53       ` Guenter Roeck

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191103044432.GA3364@taoren-ubuntu-R90MNF91 \
    --to=rentao.bupt@gmail.com \
    --cc=corbet@lwn.net \
    --cc=jdelvare@suse.com \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-hwmon@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@roeck-us.net \
    --cc=openbmc@lists.ozlabs.org \
    --cc=taoren@fb.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Hwmon Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-hwmon/0 linux-hwmon/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-hwmon linux-hwmon/ https://lore.kernel.org/linux-hwmon \
		linux-hwmon@vger.kernel.org
	public-inbox-index linux-hwmon

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-hwmon


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git