From: Guenter Roeck <linux@roeck-us.net>
To: Eric Tremblay <etremblay@distech-controls.com>
Cc: linux-hwmon@vger.kernel.org, devicetree@vger.kernel.org,
linux-doc@vger.kernel.org, jdelvare@suse.com, robh+dt@kernel.org,
mark.rutland@arm.com, corbet@lwn.net
Subject: Re: [PATCH v8 2/2] hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.
Date: Thu, 21 Nov 2019 21:27:22 -0800 [thread overview]
Message-ID: <20191122052722.GA21706@roeck-us.net> (raw)
In-Reply-To: <20191112223001.20844-3-etremblay@distech-controls.com>
On Tue, Nov 12, 2019 at 05:30:01PM -0500, Eric Tremblay wrote:
> TI's TMP512/513 are I2C/SMBus system monitor chips. These chips
> monitor the supply voltage, supply current, power consumption
> and provide one local and up to three (TMP513) remote temperature sensors.
>
> It has been tested using a TI TMP513 development kit (TMP513EVM)
>
> Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
Applied.
Thanks,
Guenter
> ---
> Documentation/hwmon/index.rst | 1 +
> Documentation/hwmon/tmp513.rst | 103 +++++
> MAINTAINERS | 7 +
> drivers/hwmon/Kconfig | 10 +
> drivers/hwmon/Makefile | 1 +
> drivers/hwmon/tmp513.c | 772 +++++++++++++++++++++++++++++++++
> 6 files changed, 894 insertions(+)
> create mode 100644 Documentation/hwmon/tmp513.rst
> create mode 100644 drivers/hwmon/tmp513.c
>
> diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> index 230ad59b462b..d708a371fce1 100644
> --- a/Documentation/hwmon/index.rst
> +++ b/Documentation/hwmon/index.rst
> @@ -153,6 +153,7 @@ Hardware Monitoring Kernel Drivers
> tmp108
> tmp401
> tmp421
> + tmp513
> tps40422
> twl4030-madc-hwmon
> ucd9000
> diff --git a/Documentation/hwmon/tmp513.rst b/Documentation/hwmon/tmp513.rst
> new file mode 100644
> index 000000000000..6c8fae4b1a75
> --- /dev/null
> +++ b/Documentation/hwmon/tmp513.rst
> @@ -0,0 +1,103 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +Kernel driver tmp513
> +====================
> +
> +Supported chips:
> +
> + * Texas Instruments TMP512
> +
> + Prefix: 'tmp512'
> +
> + Datasheet: http://www.ti.com/lit/ds/symlink/tmp512.pdf
> +
> + * Texas Instruments TMP513
> +
> + Prefix: 'tmp513'
> +
> + Datasheet: http://www.ti.com/lit/ds/symlink/tmp513.pdf
> +
> +Authors:
> +
> + Eric Tremblay <etremblay@distech-controls.com>
> +
> +Description
> +-----------
> +
> +This driver implements support for Texas Instruments TMP512, and TMP513.
> +The TMP512 (dual-channel) and TMP513 (triple-channel) are system monitors
> +that include remote sensors, a local temperature sensor, and a high-side current
> +shunt monitor. These system monitors have the capability of measuring remote
> +temperatures, on-chip temperatures, and system voltage/power/current
> +consumption.
> +
> +The temperatures are measured in degrees Celsius with a range of
> +-40 to + 125 degrees with a resolution of 0.0625 degree C.
> +
> +For hysteresis value, only the first channel is writable. Writing to it
> +will affect all other values since each channels are sharing the same
> +hysteresis value. The hysteresis is in degrees Celsius with a range of
> +0 to 127.5 degrees with a resolution of 0.5 degree.
> +
> +The driver exports the temperature values via the following sysfs files:
> +
> +**temp[1-4]_input**
> +
> +**temp[1-4]_crit**
> +
> +**temp[1-4]_crit_alarm**
> +
> +**temp[1-4]_crit_hyst**
> +
> +The driver read the shunt voltage from the chip and convert it to current.
> +The readable range depends on the "ti,pga-gain" property (default to 8) and the
> +shunt resistor value. The value resolution will be equal to 10uV/Rshunt.
> +
> +The driver exports the shunt currents values via the following sysFs files:
> +
> +**curr1_input**
> +
> +**curr1_lcrit**
> +
> +**curr1_lcrit_alarm**
> +
> +**curr1_crit**
> +
> +**curr1_crit_alarm**
> +
> +The bus voltage range is read from the chip with a resolution of 4mV. The chip
> +can be configurable in two different range (32V or 16V) using the
> +ti,bus-range-microvolt property in the devicetree.
> +
> +The driver exports the bus voltage values via the following sysFs files:
> +
> +**in0_input**
> +
> +**in0_lcrit**
> +
> +**in0_lcrit_alarm**
> +
> +**in0_crit**
> +
> +**in0_crit_alarm**
> +
> +The bus power and bus currents range and resolution depends on the calibration
> +register value. Those values are calculate by the hardware using those
> +formulas:
> +
> +Current = (ShuntVoltage * CalibrationRegister) / 4096
> +Power = (Current * BusVoltage) / 5000
> +
> +The driver exports the bus current and bus power values via the following
> +sysFs files:
> +
> +**curr2_input**
> +
> +**power1_input**
> +
> +**power1_crit**
> +
> +**power1_crit_alarm**
> +
> +The calibration process follow the procedure of the datasheet (without overflow)
> +and depend on the shunt resistor value and the pga_gain value.
> diff --git a/MAINTAINERS b/MAINTAINERS
> index eb19fad370d7..75db98a0913c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -16378,6 +16378,13 @@ S: Maintained
> F: Documentation/hwmon/tmp401.rst
> F: drivers/hwmon/tmp401.c
>
> +TMP513 HARDWARE MONITOR DRIVER
> +M: Eric Tremblay <etremblay@distech-controls.com>
> +L: linux-hwmon@vger.kernel.org
> +S: Maintained
> +F: Documentation/hwmon/tmp513.rst
> +F: drivers/hwmon/tmp513.c
> +
> TMPFS (SHMEM FILESYSTEM)
> M: Hugh Dickins <hughd@google.com>
> L: linux-mm@kvack.org
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 13a6b4afb4b3..926e3c98dbdf 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -1709,6 +1709,16 @@ config SENSORS_TMP421
> This driver can also be built as a module. If so, the module
> will be called tmp421.
>
> +config SENSORS_TMP513
> + tristate "Texas Instruments TMP513 and compatibles"
> + depends on I2C
> + help
> + If you say yes here you get support for Texas Instruments TMP512,
> + and TMP513 temperature and power supply sensor chips.
> +
> + This driver can also be built as a module. If so, the module
> + will be called tmp513.
> +
> config SENSORS_VEXPRESS
> tristate "Versatile Express"
> depends on VEXPRESS_CONFIG
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index 40c036ea45e6..762642291914 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -166,6 +166,7 @@ obj-$(CONFIG_SENSORS_TMP103) += tmp103.o
> obj-$(CONFIG_SENSORS_TMP108) += tmp108.o
> obj-$(CONFIG_SENSORS_TMP401) += tmp401.o
> obj-$(CONFIG_SENSORS_TMP421) += tmp421.o
> +obj-$(CONFIG_SENSORS_TMP513) += tmp513.o
> obj-$(CONFIG_SENSORS_VEXPRESS) += vexpress-hwmon.o
> obj-$(CONFIG_SENSORS_VIA_CPUTEMP)+= via-cputemp.o
> obj-$(CONFIG_SENSORS_VIA686A) += via686a.o
> diff --git a/drivers/hwmon/tmp513.c b/drivers/hwmon/tmp513.c
> new file mode 100644
> index 000000000000..df66e0bc1253
> --- /dev/null
> +++ b/drivers/hwmon/tmp513.c
> @@ -0,0 +1,772 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Driver for Texas Instruments TMP512, TMP513 power monitor chips
> + *
> + * TMP513:
> + * Thermal/Power Management with Triple Remote and
> + * Local Temperature Sensor and Current Shunt Monitor
> + * Datasheet: http://www.ti.com/lit/gpn/tmp513
> + *
> + * TMP512:
> + * Thermal/Power Management with Dual Remote
> + * and Local Temperature Sensor and Current Shunt Monitor
> + * Datasheet: http://www.ti.com/lit/gpn/tmp512
> + *
> + * Copyright (C) 2019 Eric Tremblay <etremblay@distech-controls.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; version 2 of the License.
> + */
> +
> +#include <linux/err.h>
> +#include <linux/hwmon.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/util_macros.h>
> +
> +// Common register definition
> +#define TMP51X_SHUNT_CONFIG 0x00
> +#define TMP51X_TEMP_CONFIG 0x01
> +#define TMP51X_STATUS 0x02
> +#define TMP51X_SMBUS_ALERT 0x03
> +#define TMP51X_SHUNT_CURRENT_RESULT 0x04
> +#define TMP51X_BUS_VOLTAGE_RESULT 0x05
> +#define TMP51X_POWER_RESULT 0x06
> +#define TMP51X_BUS_CURRENT_RESULT 0x07
> +#define TMP51X_LOCAL_TEMP_RESULT 0x08
> +#define TMP51X_REMOTE_TEMP_RESULT_1 0x09
> +#define TMP51X_REMOTE_TEMP_RESULT_2 0x0A
> +#define TMP51X_SHUNT_CURRENT_H_LIMIT 0x0C
> +#define TMP51X_SHUNT_CURRENT_L_LIMIT 0x0D
> +#define TMP51X_BUS_VOLTAGE_H_LIMIT 0x0E
> +#define TMP51X_BUS_VOLTAGE_L_LIMIT 0x0F
> +#define TMP51X_POWER_LIMIT 0x10
> +#define TMP51X_LOCAL_TEMP_LIMIT 0x11
> +#define TMP51X_REMOTE_TEMP_LIMIT_1 0x12
> +#define TMP51X_REMOTE_TEMP_LIMIT_2 0x13
> +#define TMP51X_SHUNT_CALIBRATION 0x15
> +#define TMP51X_N_FACTOR_AND_HYST_1 0x16
> +#define TMP51X_N_FACTOR_2 0x17
> +#define TMP51X_MAN_ID_REG 0xFE
> +#define TMP51X_DEVICE_ID_REG 0xFF
> +
> +// TMP513 specific register definition
> +#define TMP513_REMOTE_TEMP_RESULT_3 0x0B
> +#define TMP513_REMOTE_TEMP_LIMIT_3 0x14
> +#define TMP513_N_FACTOR_3 0x18
> +
> +// Common attrs, and NULL
> +#define TMP51X_MANUFACTURER_ID 0x55FF
> +
> +#define TMP512_DEVICE_ID 0x22FF
> +#define TMP513_DEVICE_ID 0x23FF
> +
> +// Default config
> +#define TMP51X_SHUNT_CONFIG_DEFAULT 0x399F
> +#define TMP51X_SHUNT_VALUE_DEFAULT 1000
> +#define TMP51X_VBUS_RANGE_DEFAULT TMP51X_VBUS_RANGE_32V
> +#define TMP51X_PGA_DEFAULT 8
> +#define TMP51X_MAX_REGISTER_ADDR 0xFF
> +
> +#define TMP512_TEMP_CONFIG_DEFAULT 0xBF80
> +#define TMP513_TEMP_CONFIG_DEFAULT 0xFF80
> +
> +// Mask and shift
> +#define CURRENT_SENSE_VOLTAGE_320_MASK 0x1800
> +#define CURRENT_SENSE_VOLTAGE_160_MASK 0x1000
> +#define CURRENT_SENSE_VOLTAGE_80_MASK 0x0800
> +#define CURRENT_SENSE_VOLTAGE_40_MASK 0
> +
> +#define TMP51X_BUS_VOLTAGE_MASK 0x2000
> +#define TMP51X_NFACTOR_MASK 0xFF00
> +#define TMP51X_HYST_MASK 0x00FF
> +
> +#define TMP51X_BUS_VOLTAGE_SHIFT 3
> +#define TMP51X_TEMP_SHIFT 3
> +
> +// Alarms
> +#define TMP51X_SHUNT_CURRENT_H_LIMIT_POS 15
> +#define TMP51X_SHUNT_CURRENT_L_LIMIT_POS 14
> +#define TMP51X_BUS_VOLTAGE_H_LIMIT_POS 13
> +#define TMP51X_BUS_VOLTAGE_L_LIMIT_POS 12
> +#define TMP51X_POWER_LIMIT_POS 11
> +#define TMP51X_LOCAL_TEMP_LIMIT_POS 10
> +#define TMP51X_REMOTE_TEMP_LIMIT_1_POS 9
> +#define TMP51X_REMOTE_TEMP_LIMIT_2_POS 8
> +#define TMP513_REMOTE_TEMP_LIMIT_3_POS 7
> +
> +#define TMP51X_VBUS_RANGE_32V 32000000
> +#define TMP51X_VBUS_RANGE_16V 16000000
> +
> +// Max and Min value
> +#define MAX_BUS_VOLTAGE_32_LIMIT 32764
> +#define MAX_BUS_VOLTAGE_16_LIMIT 16382
> +
> +// Max possible value is -256 to +256 but datasheet indicated -40 to 125.
> +#define MAX_TEMP_LIMIT 125000
> +#define MIN_TEMP_LIMIT -40000
> +
> +#define MAX_TEMP_HYST 127500
> +
> +static const u8 TMP51X_TEMP_INPUT[4] = {
> + TMP51X_LOCAL_TEMP_RESULT,
> + TMP51X_REMOTE_TEMP_RESULT_1,
> + TMP51X_REMOTE_TEMP_RESULT_2,
> + TMP513_REMOTE_TEMP_RESULT_3
> +};
> +
> +static const u8 TMP51X_TEMP_CRIT[4] = {
> + TMP51X_LOCAL_TEMP_LIMIT,
> + TMP51X_REMOTE_TEMP_LIMIT_1,
> + TMP51X_REMOTE_TEMP_LIMIT_2,
> + TMP513_REMOTE_TEMP_LIMIT_3
> +};
> +
> +static const u8 TMP51X_TEMP_CRIT_ALARM[4] = {
> + TMP51X_LOCAL_TEMP_LIMIT_POS,
> + TMP51X_REMOTE_TEMP_LIMIT_1_POS,
> + TMP51X_REMOTE_TEMP_LIMIT_2_POS,
> + TMP513_REMOTE_TEMP_LIMIT_3_POS
> +};
> +
> +static const u8 TMP51X_TEMP_CRIT_HYST[4] = {
> + TMP51X_N_FACTOR_AND_HYST_1,
> + TMP51X_N_FACTOR_AND_HYST_1,
> + TMP51X_N_FACTOR_AND_HYST_1,
> + TMP51X_N_FACTOR_AND_HYST_1
> +};
> +
> +static const u8 TMP51X_CURR_INPUT[2] = {
> + TMP51X_SHUNT_CURRENT_RESULT,
> + TMP51X_BUS_CURRENT_RESULT
> +};
> +
> +static struct regmap_config tmp51x_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 16,
> + .max_register = TMP51X_MAX_REGISTER_ADDR,
> +};
> +
> +enum tmp51x_ids {
> + tmp512, tmp513
> +};
> +
> +struct tmp51x_data {
> + u16 shunt_config;
> + u16 pga_gain;
> + u32 vbus_range_uvolt;
> +
> + u16 temp_config;
> + u32 nfactor[3];
> +
> + u32 shunt_uohms;
> +
> + u32 curr_lsb_ua;
> + u32 pwr_lsb_uw;
> +
> + enum tmp51x_ids id;
> + struct regmap *regmap;
> +};
> +
> +// Set the shift based on the gain 8=4, 4=3, 2=2, 1=1
> +static inline u8 tmp51x_get_pga_shift(struct tmp51x_data *data)
> +{
> + return 5 - ffs(data->pga_gain);
> +}
> +
> +static int tmp51x_get_value(struct tmp51x_data *data, u8 reg, u8 pos,
> + unsigned int regval, long *val)
> +{
> + switch (reg) {
> + case TMP51X_STATUS:
> + *val = (regval >> pos) & 1;
> + break;
> + case TMP51X_SHUNT_CURRENT_RESULT:
> + case TMP51X_SHUNT_CURRENT_H_LIMIT:
> + case TMP51X_SHUNT_CURRENT_L_LIMIT:
> + /*
> + * The valus is read in voltage in the chip but reported as
> + * current to the user.
> + * 2's compliment number shifted by one to four depending
> + * on the pga gain setting. 1lsb = 10uV
> + */
> + *val = sign_extend32(regval, 17 - tmp51x_get_pga_shift(data));
> + *val = DIV_ROUND_CLOSEST(*val * 10000, data->shunt_uohms);
> + break;
> + case TMP51X_BUS_VOLTAGE_RESULT:
> + case TMP51X_BUS_VOLTAGE_H_LIMIT:
> + case TMP51X_BUS_VOLTAGE_L_LIMIT:
> + // 1lsb = 4mV
> + *val = (regval >> TMP51X_BUS_VOLTAGE_SHIFT) * 4;
> + break;
> + case TMP51X_POWER_RESULT:
> + case TMP51X_POWER_LIMIT:
> + // Power = (current * BusVoltage) / 5000
> + *val = regval * data->pwr_lsb_uw;
> + break;
> + case TMP51X_BUS_CURRENT_RESULT:
> + // Current = (ShuntVoltage * CalibrationRegister) / 4096
> + *val = sign_extend32(regval, 16) * data->curr_lsb_ua;
> + *val = DIV_ROUND_CLOSEST(*val, 1000);
> + break;
> + case TMP51X_LOCAL_TEMP_RESULT:
> + case TMP51X_REMOTE_TEMP_RESULT_1:
> + case TMP51X_REMOTE_TEMP_RESULT_2:
> + case TMP513_REMOTE_TEMP_RESULT_3:
> + case TMP51X_LOCAL_TEMP_LIMIT:
> + case TMP51X_REMOTE_TEMP_LIMIT_1:
> + case TMP51X_REMOTE_TEMP_LIMIT_2:
> + case TMP513_REMOTE_TEMP_LIMIT_3:
> + // 1lsb = 0.0625 degrees centigrade
> + *val = sign_extend32(regval, 16) >> TMP51X_TEMP_SHIFT;
> + *val = DIV_ROUND_CLOSEST(*val * 625, 10);
> + break;
> + case TMP51X_N_FACTOR_AND_HYST_1:
> + // 1lsb = 0.5 degrees centigrade
> + *val = (regval & TMP51X_HYST_MASK) * 500;
> + break;
> + default:
> + // Programmer goofed
> + WARN_ON_ONCE(1);
> + *val = 0;
> + return -EOPNOTSUPP;
> + }
> +
> + return 0;
> +}
> +
> +static int tmp51x_set_value(struct tmp51x_data *data, u8 reg, long val)
> +{
> + int regval, max_val;
> + u32 mask = 0;
> +
> + switch (reg) {
> + case TMP51X_SHUNT_CURRENT_H_LIMIT:
> + case TMP51X_SHUNT_CURRENT_L_LIMIT:
> + /*
> + * The user enter current value and we convert it to
> + * voltage. 1lsb = 10uV
> + */
> + val = DIV_ROUND_CLOSEST(val * data->shunt_uohms, 10000);
> + max_val = U16_MAX >> tmp51x_get_pga_shift(data);
> + regval = clamp_val(val, -max_val, max_val);
> + break;
> + case TMP51X_BUS_VOLTAGE_H_LIMIT:
> + case TMP51X_BUS_VOLTAGE_L_LIMIT:
> + // 1lsb = 4mV
> + max_val = (data->vbus_range_uvolt == TMP51X_VBUS_RANGE_32V) ?
> + MAX_BUS_VOLTAGE_32_LIMIT : MAX_BUS_VOLTAGE_16_LIMIT;
> +
> + val = clamp_val(DIV_ROUND_CLOSEST(val, 4), 0, max_val);
> + regval = val << TMP51X_BUS_VOLTAGE_SHIFT;
> + break;
> + case TMP51X_POWER_LIMIT:
> + regval = clamp_val(DIV_ROUND_CLOSEST(val, data->pwr_lsb_uw), 0,
> + U16_MAX);
> + break;
> + case TMP51X_LOCAL_TEMP_LIMIT:
> + case TMP51X_REMOTE_TEMP_LIMIT_1:
> + case TMP51X_REMOTE_TEMP_LIMIT_2:
> + case TMP513_REMOTE_TEMP_LIMIT_3:
> + // 1lsb = 0.0625 degrees centigrade
> + val = clamp_val(val, MIN_TEMP_LIMIT, MAX_TEMP_LIMIT);
> + regval = DIV_ROUND_CLOSEST(val * 10, 625) << TMP51X_TEMP_SHIFT;
> + break;
> + case TMP51X_N_FACTOR_AND_HYST_1:
> + // 1lsb = 0.5 degrees centigrade
> + val = clamp_val(val, 0, MAX_TEMP_HYST);
> + regval = DIV_ROUND_CLOSEST(val, 500);
> + mask = TMP51X_HYST_MASK;
> + break;
> + default:
> + // Programmer goofed
> + WARN_ON_ONCE(1);
> + return -EOPNOTSUPP;
> + }
> +
> + if (mask == 0)
> + return regmap_write(data->regmap, reg, regval);
> + else
> + return regmap_update_bits(data->regmap, reg, mask, regval);
> +}
> +
> +static u8 tmp51x_get_reg(enum hwmon_sensor_types type, u32 attr, int channel)
> +{
> + switch (type) {
> + case hwmon_temp:
> + switch (attr) {
> + case hwmon_temp_input:
> + return TMP51X_TEMP_INPUT[channel];
> + case hwmon_temp_crit_alarm:
> + return TMP51X_STATUS;
> + case hwmon_temp_crit:
> + return TMP51X_TEMP_CRIT[channel];
> + case hwmon_temp_crit_hyst:
> + return TMP51X_TEMP_CRIT_HYST[channel];
> + }
> + break;
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_input:
> + return TMP51X_BUS_VOLTAGE_RESULT;
> + case hwmon_in_lcrit_alarm:
> + case hwmon_in_crit_alarm:
> + return TMP51X_STATUS;
> + case hwmon_in_lcrit:
> + return TMP51X_BUS_VOLTAGE_L_LIMIT;
> + case hwmon_in_crit:
> + return TMP51X_BUS_VOLTAGE_H_LIMIT;
> + }
> + break;
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + return TMP51X_CURR_INPUT[channel];
> + case hwmon_curr_lcrit_alarm:
> + case hwmon_curr_crit_alarm:
> + return TMP51X_STATUS;
> + case hwmon_curr_lcrit:
> + return TMP51X_SHUNT_CURRENT_L_LIMIT;
> + case hwmon_curr_crit:
> + return TMP51X_SHUNT_CURRENT_H_LIMIT;
> + }
> + break;
> + case hwmon_power:
> + switch (attr) {
> + case hwmon_power_input:
> + return TMP51X_POWER_RESULT;
> + case hwmon_power_crit_alarm:
> + return TMP51X_STATUS;
> + case hwmon_power_crit:
> + return TMP51X_POWER_LIMIT;
> + }
> + break;
> + default:
> + break;
> + }
> +
> + return 0;
> +}
> +
> +static u8 tmp51x_get_status_pos(enum hwmon_sensor_types type, u32 attr,
> + int channel)
> +{
> + switch (type) {
> + case hwmon_temp:
> + switch (attr) {
> + case hwmon_temp_crit_alarm:
> + return TMP51X_TEMP_CRIT_ALARM[channel];
> + }
> + break;
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_lcrit_alarm:
> + return TMP51X_BUS_VOLTAGE_L_LIMIT_POS;
> + case hwmon_in_crit_alarm:
> + return TMP51X_BUS_VOLTAGE_H_LIMIT_POS;
> + }
> + break;
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_lcrit_alarm:
> + return TMP51X_SHUNT_CURRENT_L_LIMIT_POS;
> + case hwmon_curr_crit_alarm:
> + return TMP51X_SHUNT_CURRENT_H_LIMIT_POS;
> + }
> + break;
> + case hwmon_power:
> + switch (attr) {
> + case hwmon_power_crit_alarm:
> + return TMP51X_POWER_LIMIT_POS;
> + }
> + break;
> + default:
> + break;
> + }
> +
> + return 0;
> +}
> +
> +static int tmp51x_read(struct device *dev, enum hwmon_sensor_types type,
> + u32 attr, int channel, long *val)
> +{
> + struct tmp51x_data *data = dev_get_drvdata(dev);
> + int ret;
> + u32 regval;
> + u8 pos = 0, reg = 0;
> +
> + reg = tmp51x_get_reg(type, attr, channel);
> + if (reg == 0)
> + return -EOPNOTSUPP;
> +
> + if (reg == TMP51X_STATUS)
> + pos = tmp51x_get_status_pos(type, attr, channel);
> +
> + ret = regmap_read(data->regmap, reg, ®val);
> + if (ret < 0)
> + return ret;
> +
> + return tmp51x_get_value(data, reg, pos, regval, val);
> +}
> +
> +static int tmp51x_write(struct device *dev, enum hwmon_sensor_types type,
> + u32 attr, int channel, long val)
> +{
> + u8 reg = 0;
> +
> + reg = tmp51x_get_reg(type, attr, channel);
> + if (reg == 0)
> + return -EOPNOTSUPP;
> +
> + return tmp51x_set_value(dev_get_drvdata(dev), reg, val);
> +}
> +
> +static umode_t tmp51x_is_visible(const void *_data,
> + enum hwmon_sensor_types type, u32 attr,
> + int channel)
> +{
> + const struct tmp51x_data *data = _data;
> +
> + switch (type) {
> + case hwmon_temp:
> + if (data->id == tmp512 && channel == 4)
> + return 0;
> + switch (attr) {
> + case hwmon_temp_input:
> + case hwmon_temp_crit_alarm:
> + return 0444;
> + case hwmon_temp_crit:
> + return 0644;
> + case hwmon_temp_crit_hyst:
> + if (channel == 0)
> + return 0644;
> + return 0444;
> + }
> + break;
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_input:
> + case hwmon_in_lcrit_alarm:
> + case hwmon_in_crit_alarm:
> + return 0444;
> + case hwmon_in_lcrit:
> + case hwmon_in_crit:
> + return 0644;
> + }
> + break;
> + case hwmon_curr:
> + if (!data->shunt_uohms)
> + return 0;
> +
> + switch (attr) {
> + case hwmon_curr_input:
> + case hwmon_curr_lcrit_alarm:
> + case hwmon_curr_crit_alarm:
> + return 0444;
> + case hwmon_curr_lcrit:
> + case hwmon_curr_crit:
> + return 0644;
> + }
> + break;
> + case hwmon_power:
> + if (!data->shunt_uohms)
> + return 0;
> +
> + switch (attr) {
> + case hwmon_power_input:
> + case hwmon_power_crit_alarm:
> + return 0444;
> + case hwmon_power_crit:
> + return 0644;
> + }
> + break;
> + default:
> + break;
> + }
> + return 0;
> +}
> +
> +static const struct hwmon_channel_info *tmp51x_info[] = {
> + HWMON_CHANNEL_INFO(temp,
> + HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_CRIT_ALARM |
> + HWMON_T_CRIT_HYST,
> + HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_CRIT_ALARM |
> + HWMON_T_CRIT_HYST,
> + HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_CRIT_ALARM |
> + HWMON_T_CRIT_HYST,
> + HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_CRIT_ALARM |
> + HWMON_T_CRIT_HYST),
> + HWMON_CHANNEL_INFO(in,
> + HWMON_I_INPUT | HWMON_I_LCRIT | HWMON_I_LCRIT_ALARM |
> + HWMON_I_CRIT | HWMON_I_CRIT_ALARM),
> + HWMON_CHANNEL_INFO(curr,
> + HWMON_C_INPUT | HWMON_C_LCRIT | HWMON_C_LCRIT_ALARM |
> + HWMON_C_CRIT | HWMON_C_CRIT_ALARM,
> + HWMON_C_INPUT),
> + HWMON_CHANNEL_INFO(power,
> + HWMON_P_INPUT | HWMON_P_CRIT | HWMON_P_CRIT_ALARM),
> + NULL
> +};
> +
> +static const struct hwmon_ops tmp51x_hwmon_ops = {
> + .is_visible = tmp51x_is_visible,
> + .read = tmp51x_read,
> + .write = tmp51x_write,
> +};
> +
> +static const struct hwmon_chip_info tmp51x_chip_info = {
> + .ops = &tmp51x_hwmon_ops,
> + .info = tmp51x_info,
> +};
> +
> +/*
> + * Calibrate the tmp51x following the datasheet method
> + */
> +static int tmp51x_calibrate(struct tmp51x_data *data)
> +{
> + int vshunt_max = data->pga_gain * 40;
> + u64 max_curr_ma;
> + u32 div;
> +
> + /*
> + * If shunt_uohms is equal to 0, the calibration should be set to 0.
> + * The consequence will be that the current and power measurement engine
> + * of the sensor will not work. Temperature and voltage sensing will
> + * continue to work.
> + */
> + if (data->shunt_uohms == 0)
> + return regmap_write(data->regmap, TMP51X_SHUNT_CALIBRATION, 0);
> +
> + max_curr_ma = DIV_ROUND_CLOSEST_ULL(vshunt_max * 1000 * 1000,
> + data->shunt_uohms);
> +
> + /*
> + * Calculate the minimal bit resolution for the current and the power.
> + * Those values will be used during register interpretation.
> + */
> + data->curr_lsb_ua = DIV_ROUND_CLOSEST_ULL(max_curr_ma * 1000, 32767);
> + data->pwr_lsb_uw = 20 * data->curr_lsb_ua;
> +
> + div = DIV_ROUND_CLOSEST_ULL(data->curr_lsb_ua * data->shunt_uohms,
> + 1000 * 1000);
> +
> + return regmap_write(data->regmap, TMP51X_SHUNT_CALIBRATION,
> + DIV_ROUND_CLOSEST(40960, div));
> +}
> +
> +/*
> + * Initialize the configuration and calibration registers.
> + */
> +static int tmp51x_init(struct tmp51x_data *data)
> +{
> + unsigned int regval;
> + int ret = regmap_write(data->regmap, TMP51X_SHUNT_CONFIG,
> + data->shunt_config);
> + if (ret < 0)
> + return ret;
> +
> + ret = regmap_write(data->regmap, TMP51X_TEMP_CONFIG, data->temp_config);
> + if (ret < 0)
> + return ret;
> +
> + // nFactor configuration
> + ret = regmap_update_bits(data->regmap, TMP51X_N_FACTOR_AND_HYST_1,
> + TMP51X_NFACTOR_MASK, data->nfactor[0] << 8);
> + if (ret < 0)
> + return ret;
> +
> + ret = regmap_write(data->regmap, TMP51X_N_FACTOR_2,
> + data->nfactor[1] << 8);
> + if (ret < 0)
> + return ret;
> +
> + if (data->id == tmp513) {
> + ret = regmap_write(data->regmap, TMP513_N_FACTOR_3,
> + data->nfactor[2] << 8);
> + if (ret < 0)
> + return ret;
> + }
> +
> + ret = tmp51x_calibrate(data);
> + if (ret < 0)
> + return ret;
> +
> + // Read the status register before using as the datasheet propose
> + return regmap_read(data->regmap, TMP51X_STATUS, ®val);
> +}
> +
> +static const struct i2c_device_id tmp51x_id[] = {
> + { "tmp512", tmp512 },
> + { "tmp513", tmp513 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(i2c, tmp51x_id);
> +
> +static const struct of_device_id tmp51x_of_match[] = {
> + {
> + .compatible = "ti,tmp512",
> + .data = (void *)tmp512
> + },
> + {
> + .compatible = "ti,tmp513",
> + .data = (void *)tmp513
> + },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, tmp51x_of_match);
> +
> +static int tmp51x_vbus_range_to_reg(struct device *dev,
> + struct tmp51x_data *data)
> +{
> + if (data->vbus_range_uvolt == TMP51X_VBUS_RANGE_32V) {
> + data->shunt_config |= TMP51X_BUS_VOLTAGE_MASK;
> + } else if (data->vbus_range_uvolt == TMP51X_VBUS_RANGE_16V) {
> + data->shunt_config &= ~TMP51X_BUS_VOLTAGE_MASK;
> + } else {
> + dev_err(dev, "ti,bus-range-microvolt is invalid: %u\n",
> + data->vbus_range_uvolt);
> + return -EINVAL;
> + }
> + return 0;
> +}
> +
> +static int tmp51x_pga_gain_to_reg(struct device *dev, struct tmp51x_data *data)
> +{
> + if (data->pga_gain == 8) {
> + data->shunt_config |= CURRENT_SENSE_VOLTAGE_320_MASK;
> + } else if (data->pga_gain == 4) {
> + data->shunt_config |= CURRENT_SENSE_VOLTAGE_160_MASK;
> + } else if (data->pga_gain == 2) {
> + data->shunt_config |= CURRENT_SENSE_VOLTAGE_80_MASK;
> + } else if (data->pga_gain == 1) {
> + data->shunt_config |= CURRENT_SENSE_VOLTAGE_40_MASK;
> + } else {
> + dev_err(dev, "ti,pga-gain is invalid: %u\n", data->pga_gain);
> + return -EINVAL;
> + }
> + return 0;
> +}
> +
> +static int tmp51x_read_properties(struct device *dev, struct tmp51x_data *data)
> +{
> + int ret;
> + u32 nfactor[3];
> + u32 val;
> +
> + ret = device_property_read_u32(dev, "shunt-resistor-micro-ohms", &val);
> + data->shunt_uohms = (ret >= 0) ? val : TMP51X_SHUNT_VALUE_DEFAULT;
> +
> + ret = device_property_read_u32(dev, "ti,bus-range-microvolt", &val);
> + data->vbus_range_uvolt = (ret >= 0) ? val : TMP51X_VBUS_RANGE_DEFAULT;
> + ret = tmp51x_vbus_range_to_reg(dev, data);
> + if (ret < 0)
> + return ret;
> +
> + ret = device_property_read_u32(dev, "ti,pga-gain", &val);
> + data->pga_gain = (ret >= 0) ? val : TMP51X_PGA_DEFAULT;
> + ret = tmp51x_pga_gain_to_reg(dev, data);
> + if (ret < 0)
> + return ret;
> +
> + ret = device_property_read_u32_array(dev, "ti,nfactor", nfactor,
> + (data->id == tmp513) ? 3 : 2);
> + if (ret >= 0)
> + memcpy(data->nfactor, nfactor, (data->id == tmp513) ? 3 : 2);
> +
> + // Check if shunt value is compatible with pga-gain
> + if (data->shunt_uohms > data->pga_gain * 40 * 1000 * 1000) {
> + dev_err(dev, "shunt-resistor: %u too big for pga_gain: %u\n",
> + data->shunt_uohms, data->pga_gain);
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static void tmp51x_use_default(struct tmp51x_data *data)
> +{
> + data->vbus_range_uvolt = TMP51X_VBUS_RANGE_DEFAULT;
> + data->pga_gain = TMP51X_PGA_DEFAULT;
> + data->shunt_uohms = TMP51X_SHUNT_VALUE_DEFAULT;
> +}
> +
> +static int tmp51x_configure(struct device *dev, struct tmp51x_data *data)
> +{
> + data->shunt_config = TMP51X_SHUNT_CONFIG_DEFAULT;
> + data->temp_config = (data->id == tmp513) ?
> + TMP513_TEMP_CONFIG_DEFAULT : TMP512_TEMP_CONFIG_DEFAULT;
> +
> + if (dev->of_node)
> + return tmp51x_read_properties(dev, data);
> +
> + tmp51x_use_default(data);
> +
> + return 0;
> +}
> +
> +static int tmp51x_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &client->dev;
> + struct tmp51x_data *data;
> + struct device *hwmon_dev;
> + int ret;
> +
> + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + if (client->dev.of_node)
> + data->id = (enum tmp51x_ids)device_get_match_data(&client->dev);
> + else
> + data->id = id->driver_data;
> +
> + ret = tmp51x_configure(dev, data);
> + if (ret < 0) {
> + dev_err(dev, "error configuring the device: %d\n", ret);
> + return ret;
> + }
> +
> + data->regmap = devm_regmap_init_i2c(client, &tmp51x_regmap_config);
> + if (IS_ERR(data->regmap)) {
> + dev_err(dev, "failed to allocate register map\n");
> + return PTR_ERR(data->regmap);
> + }
> +
> + ret = tmp51x_init(data);
> + if (ret < 0) {
> + dev_err(dev, "error configuring the device: %d\n", ret);
> + return -ENODEV;
> + }
> +
> + hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name,
> + data,
> + &tmp51x_chip_info,
> + NULL);
> + if (IS_ERR(hwmon_dev))
> + return PTR_ERR(hwmon_dev);
> +
> + dev_dbg(dev, "power monitor %s\n", id->name);
> +
> + return 0;
> +}
> +
> +static struct i2c_driver tmp51x_driver = {
> + .driver = {
> + .name = "tmp51x",
> + .of_match_table = of_match_ptr(tmp51x_of_match),
> + },
> + .probe = tmp51x_probe,
> + .id_table = tmp51x_id,
> +};
> +
> +module_i2c_driver(tmp51x_driver);
> +
> +MODULE_AUTHOR("Eric Tremblay <etremblay@distechcontrols.com>");
> +MODULE_DESCRIPTION("tmp51x driver");
> +MODULE_LICENSE("GPL");
prev parent reply other threads:[~2019-11-22 5:27 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-12 22:29 [PATCH v8 0/2] hwmon: Add driver for Texas Instruments TMP512/513 sensor chips Eric Tremblay
2019-11-12 22:30 ` [PATCH v8 1/2] dt-bindings: hwmon: Add TMP512/513 Eric Tremblay
2019-11-18 21:31 ` Rob Herring
2019-11-22 5:27 ` Guenter Roeck
2019-11-12 22:30 ` [PATCH v8 2/2] hwmon: Add driver for Texas Instruments TMP512/513 sensor chips Eric Tremblay
2019-11-22 5:27 ` Guenter Roeck [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191122052722.GA21706@roeck-us.net \
--to=linux@roeck-us.net \
--cc=corbet@lwn.net \
--cc=devicetree@vger.kernel.org \
--cc=etremblay@distech-controls.com \
--cc=jdelvare@suse.com \
--cc=linux-doc@vger.kernel.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).