linux-hwmon.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v4 0/5] hwmon: ltc2945: Add binding and shunt resistor support
@ 2023-01-26 22:32 Jonathan Cormier
  2023-01-26 22:32 ` [PATCH v4 1/5] dt-bindings: hwmon: adi,ltc2945: Add binding Jonathan Cormier
                   ` (4 more replies)
  0 siblings, 5 replies; 10+ messages in thread
From: Jonathan Cormier @ 2023-01-26 22:32 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, Rob Herring, Krzysztof Kozlowski
  Cc: linux-hwmon, devicetree, linux-kernel, Bob Duke, John Pruitt,
	Jonathan Cormier, Krzysztof Kozlowski

Added the ability to specify the value of the shunt resistor in the
device tree instead of assuming it is 1 milliOhm.

Would be good to backport as well

Changes since v3:
- Remove shunt-resistor-micro-ohms in binding commit message
- Simplify ltc2945_value_store fix
- Validate overflow
- ltc2945_value_store accept only 32-bit uint from user to avoid overflow
- Link to v3: https://lore.kernel.org/r/20230109233534.1932370-1-jcormier@criticallink.com
Changes since v2:
- Remove newline
- Combined overflow fix with "Allow setting shunt resistor" commit
- Add description to "Add devicetree match table"
- Add fix for unhandled error case in ltc2945_value_store
- Use imperative in descriptions
- Remove unneeded overflow check from ltc2945_reg_to_val
- Fix up DIV_ROUND_CLOSEST_ULL calls, per docs divisor should be 32-bit
- Split one DIV_ROUND_CLOSEST_ULL change into separate commit per
 Guenter Roeck's comment
Changes since v1:
- Add devicetree match table
- Add kerneldoc for the ltc2945_data struct
- Cleanup excesive comments about the shunt resistor
- Switch to device_property_read_u32()

Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
---
John Pruitt (1):
      hwmon: ltc2945: Allow setting shunt resistor

Jonathan Cormier (4):
      dt-bindings: hwmon: adi,ltc2945: Add binding
      hwmon: ltc2945: Add devicetree match table
      hwmon: ltc2945: Handle error case in ltc2945_value_store
      hwmon: ltc2945: Convert division to DIV_ROUND_CLOSEST_ULL

 .../devicetree/bindings/hwmon/adi,ltc2945.yaml     |  49 ++++++++
 drivers/hwmon/ltc2945.c                            | 132 ++++++++++++++-------
 2 files changed, 136 insertions(+), 45 deletions(-)
---
base-commit: 93f875a8526a291005e7f38478079526c843cbec
change-id: 20230126-b4-ltc2945_shunt_resistor-f64955044365

Best regards,
-- 
Jonathan Cormier <jcormier@criticallink.com>


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v4 1/5] dt-bindings: hwmon: adi,ltc2945: Add binding
  2023-01-26 22:32 [PATCH v4 0/5] hwmon: ltc2945: Add binding and shunt resistor support Jonathan Cormier
@ 2023-01-26 22:32 ` Jonathan Cormier
  2023-01-29 20:16   ` Guenter Roeck
  2023-01-26 22:32 ` [PATCH v4 2/5] hwmon: ltc2945: Add devicetree match table Jonathan Cormier
                   ` (3 subsequent siblings)
  4 siblings, 1 reply; 10+ messages in thread
From: Jonathan Cormier @ 2023-01-26 22:32 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, Rob Herring, Krzysztof Kozlowski
  Cc: linux-hwmon, devicetree, linux-kernel, Bob Duke, John Pruitt,
	Jonathan Cormier, Krzysztof Kozlowski

Create initial binding for the LTC2945 I2C power monitor.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
---
 .../devicetree/bindings/hwmon/adi,ltc2945.yaml     | 49 ++++++++++++++++++++++
 1 file changed, 49 insertions(+)

diff --git a/Documentation/devicetree/bindings/hwmon/adi,ltc2945.yaml b/Documentation/devicetree/bindings/hwmon/adi,ltc2945.yaml
new file mode 100644
index 000000000000..5cb66e97e816
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/adi,ltc2945.yaml
@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/adi,ltc2945.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices LTC2945 wide range i2c power monitor
+
+maintainers:
+  - Guenter Roeck <linux@roeck-us.net>
+
+description: |
+  Analog Devices LTC2945 wide range i2c power monitor over I2C.
+
+  https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2945.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,ltc2945
+
+  reg:
+    maxItems: 1
+
+  shunt-resistor-micro-ohms:
+    description:
+      Shunt resistor value in micro-Ohms
+    default: 1000
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        power-monitor@6e {
+            compatible = "adi,ltc2945";
+            reg = <0x6e>;
+            /* 10 milli-Ohm shunt resistor */
+            shunt-resistor-micro-ohms = <10000>;
+        };
+    };
+...

-- 
2.25.1


^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH v4 2/5] hwmon: ltc2945: Add devicetree match table
  2023-01-26 22:32 [PATCH v4 0/5] hwmon: ltc2945: Add binding and shunt resistor support Jonathan Cormier
  2023-01-26 22:32 ` [PATCH v4 1/5] dt-bindings: hwmon: adi,ltc2945: Add binding Jonathan Cormier
@ 2023-01-26 22:32 ` Jonathan Cormier
  2023-01-26 22:32 ` [PATCH v4 3/5] hwmon: ltc2945: Handle error case in ltc2945_value_store Jonathan Cormier
                   ` (2 subsequent siblings)
  4 siblings, 0 replies; 10+ messages in thread
From: Jonathan Cormier @ 2023-01-26 22:32 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, Rob Herring, Krzysztof Kozlowski
  Cc: linux-hwmon, devicetree, linux-kernel, Bob Duke, John Pruitt,
	Jonathan Cormier

Add adi,ltc2945 compatible

Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
---
 drivers/hwmon/ltc2945.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/hwmon/ltc2945.c b/drivers/hwmon/ltc2945.c
index 9adebb59f604..9af3e3821152 100644
--- a/drivers/hwmon/ltc2945.c
+++ b/drivers/hwmon/ltc2945.c
@@ -58,6 +58,12 @@
 #define CONTROL_MULT_SELECT	(1 << 0)
 #define CONTROL_TEST_MODE	(1 << 4)
 
+static const struct of_device_id __maybe_unused ltc2945_of_match[] = {
+	{ .compatible = "adi,ltc2945" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ltc2945_of_match);
+
 static inline bool is_power_reg(u8 reg)
 {
 	return reg < LTC2945_SENSE_H;
@@ -475,8 +481,9 @@ MODULE_DEVICE_TABLE(i2c, ltc2945_id);
 
 static struct i2c_driver ltc2945_driver = {
 	.driver = {
-		   .name = "ltc2945",
-		   },
+		.name = "ltc2945",
+		.of_match_table = of_match_ptr(ltc2945_of_match),
+	},
 	.probe_new = ltc2945_probe,
 	.id_table = ltc2945_id,
 };

-- 
2.25.1


^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH v4 3/5] hwmon: ltc2945: Handle error case in ltc2945_value_store
  2023-01-26 22:32 [PATCH v4 0/5] hwmon: ltc2945: Add binding and shunt resistor support Jonathan Cormier
  2023-01-26 22:32 ` [PATCH v4 1/5] dt-bindings: hwmon: adi,ltc2945: Add binding Jonathan Cormier
  2023-01-26 22:32 ` [PATCH v4 2/5] hwmon: ltc2945: Add devicetree match table Jonathan Cormier
@ 2023-01-26 22:32 ` Jonathan Cormier
  2023-01-26 22:32 ` [PATCH v4 4/5] hwmon: ltc2945: Allow setting shunt resistor Jonathan Cormier
  2023-01-26 22:32 ` [PATCH v4 5/5] hwmon: ltc2945: Convert division to DIV_ROUND_CLOSEST_ULL Jonathan Cormier
  4 siblings, 0 replies; 10+ messages in thread
From: Jonathan Cormier @ 2023-01-26 22:32 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, Rob Herring, Krzysztof Kozlowski
  Cc: linux-hwmon, devicetree, linux-kernel, Bob Duke, John Pruitt,
	Jonathan Cormier

ltc2945_val_to_reg errors were not being handled
which would have resulted in register being set to
0 (clamped) instead of being left alone.

Fixes: 6700ce035f83 ("hwmon: Driver for Linear Technologies LTC2945")

Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
---
 drivers/hwmon/ltc2945.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/hwmon/ltc2945.c b/drivers/hwmon/ltc2945.c
index 9af3e3821152..ac15298a6558 100644
--- a/drivers/hwmon/ltc2945.c
+++ b/drivers/hwmon/ltc2945.c
@@ -254,6 +254,8 @@ static ssize_t ltc2945_value_store(struct device *dev,
 
 	/* convert to register value, then clamp and write result */
 	regval = ltc2945_val_to_reg(dev, reg, val);
+	if (regval < 0)
+		return regval;
 	if (is_power_reg(reg)) {
 		regval = clamp_val(regval, 0, 0xffffff);
 		regbuf[0] = regval >> 16;

-- 
2.25.1


^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH v4 4/5] hwmon: ltc2945: Allow setting shunt resistor
  2023-01-26 22:32 [PATCH v4 0/5] hwmon: ltc2945: Add binding and shunt resistor support Jonathan Cormier
                   ` (2 preceding siblings ...)
  2023-01-26 22:32 ` [PATCH v4 3/5] hwmon: ltc2945: Handle error case in ltc2945_value_store Jonathan Cormier
@ 2023-01-26 22:32 ` Jonathan Cormier
  2023-01-26 22:32 ` [PATCH v4 5/5] hwmon: ltc2945: Convert division to DIV_ROUND_CLOSEST_ULL Jonathan Cormier
  4 siblings, 0 replies; 10+ messages in thread
From: Jonathan Cormier @ 2023-01-26 22:32 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, Rob Herring, Krzysztof Kozlowski
  Cc: linux-hwmon, devicetree, linux-kernel, Bob Duke, John Pruitt,
	Jonathan Cormier

From: John Pruitt <jpruitt@criticallink.com>

Add the ability to specify the value of the shunt resistor in the
device tree instead of assuming it is 1 milliOhm. The value in the
device tree has the name shunt-resistor-micro-ohms and the
default value is 1000 micro-ohms in order to preserve the
current behavior.

Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: John Pruitt <jpruitt@criticallink.com>
---
 drivers/hwmon/ltc2945.c | 117 +++++++++++++++++++++++++++++++-----------------
 1 file changed, 75 insertions(+), 42 deletions(-)

diff --git a/drivers/hwmon/ltc2945.c b/drivers/hwmon/ltc2945.c
index ac15298a6558..0b5e448b4f12 100644
--- a/drivers/hwmon/ltc2945.c
+++ b/drivers/hwmon/ltc2945.c
@@ -64,6 +64,16 @@ static const struct of_device_id __maybe_unused ltc2945_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, ltc2945_of_match);
 
+/**
+ * struct ltc2945_data - LTC2945 device data
+ * @regmap: regmap device
+ * @shunt_resistor: shunt resistor value in micro ohms (1000 by default)
+ */
+struct ltc2945_data {
+	struct regmap *regmap;
+	u32 shunt_resistor;
+};
+
 static inline bool is_power_reg(u8 reg)
 {
 	return reg < LTC2945_SENSE_H;
@@ -72,7 +82,9 @@ static inline bool is_power_reg(u8 reg)
 /* Return the value from the given register in uW, mV, or mA */
 static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
 {
-	struct regmap *regmap = dev_get_drvdata(dev);
+	struct ltc2945_data *data = dev_get_drvdata(dev);
+	struct regmap *regmap = data->regmap;
+	u32 shunt_resistor = data->shunt_resistor;
 	unsigned int control;
 	u8 buf[3];
 	long long val;
@@ -84,10 +96,10 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
 		return ret;
 
 	if (is_power_reg(reg)) {
-		/* power */
+		/* 24-bit power */
 		val = (buf[0] << 16) + (buf[1] << 8) + buf[2];
 	} else {
-		/* current, voltage */
+		/* 12-bit current, voltage */
 		val = (buf[0] << 4) + (buf[1] >> 4);
 	}
 
@@ -98,9 +110,7 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
 	case LTC2945_MAX_POWER_THRES_H:
 	case LTC2945_MIN_POWER_THRES_H:
 		/*
-		 * Convert to uW by assuming current is measured with
-		 * an 1mOhm sense resistor, similar to current
-		 * measurements.
+		 * Convert to uW
 		 * Control register bit 0 selects if voltage at SENSE+/VDD
 		 * or voltage at ADIN is used to measure power.
 		 */
@@ -114,6 +124,14 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
 			/* 0.5 mV * 25 uV = 0.0125 uV resolution. */
 			val = (val * 25LL) >> 1;
 		}
+		val *= 1000;
+		/* Overflow check: Assuming max 24-bit power, val is at most 53 bits right now. */
+		val = DIV_ROUND_CLOSEST_ULL(val, shunt_resistor);
+		/*
+		 * Overflow check: After division, depending on shunt resistor,
+		 * val can still be > 32 bits so returning long long makes sense
+		 */
+
 		break;
 	case LTC2945_VIN_H:
 	case LTC2945_MAX_VIN_H:
@@ -136,14 +154,11 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
 	case LTC2945_MIN_SENSE_H:
 	case LTC2945_MAX_SENSE_THRES_H:
 	case LTC2945_MIN_SENSE_THRES_H:
-		/*
-		 * 25 uV resolution. Convert to current as measured with
-		 * an 1 mOhm sense resistor, in mA. If a different sense
-		 * resistor is installed, calculate the actual current by
-		 * dividing the reported current by the sense resistor value
-		 * in mOhm.
-		 */
-		val *= 25;
+		/* 25 uV resolution. Convert to mA. */
+		val *= 25 * 1000;
+		/* Overflow check: Assuming max 12-bit sense, val is at most 27 bits right now */
+		val = DIV_ROUND_CLOSEST_ULL(val, shunt_resistor);
+		/* Overflow check: After division, <= 27 bits */
 		break;
 	default:
 		return -EINVAL;
@@ -151,13 +166,18 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
 	return val;
 }
 
-static int ltc2945_val_to_reg(struct device *dev, u8 reg,
-			      unsigned long val)
+static long long ltc2945_val_to_reg(struct device *dev, u8 reg,
+			      unsigned long long val)
 {
-	struct regmap *regmap = dev_get_drvdata(dev);
+	struct ltc2945_data *data = dev_get_drvdata(dev);
+	struct regmap *regmap = data->regmap;
+	u32 shunt_resistor = data->shunt_resistor;
 	unsigned int control;
 	int ret;
 
+	/* Ensure we don't overflow */
+	val = clamp_val(val, 0, U32_MAX);
+
 	switch (reg) {
 	case LTC2945_POWER_H:
 	case LTC2945_MAX_POWER_H:
@@ -165,9 +185,6 @@ static int ltc2945_val_to_reg(struct device *dev, u8 reg,
 	case LTC2945_MAX_POWER_THRES_H:
 	case LTC2945_MIN_POWER_THRES_H:
 		/*
-		 * Convert to register value by assuming current is measured
-		 * with an 1mOhm sense resistor, similar to current
-		 * measurements.
 		 * Control register bit 0 selects if voltage at SENSE+/VDD
 		 * or voltage at ADIN is used to measure power, which in turn
 		 * determines register calculations.
@@ -177,14 +194,16 @@ static int ltc2945_val_to_reg(struct device *dev, u8 reg,
 			return ret;
 		if (control & CONTROL_MULT_SELECT) {
 			/* 25 mV * 25 uV = 0.625 uV resolution. */
-			val = DIV_ROUND_CLOSEST(val, 625);
+			val *= shunt_resistor;
+			/* Overflow check: Assuming 32-bit val and shunt resistor, val <= 64bits */
+			val = DIV_ROUND_CLOSEST_ULL(val, 625 * 1000);
+			/* Overflow check: val is now <= 44 bits */
 		} else {
-			/*
-			 * 0.5 mV * 25 uV = 0.0125 uV resolution.
-			 * Divide first to avoid overflow;
-			 * accept loss of accuracy.
-			 */
-			val = DIV_ROUND_CLOSEST(val, 25) * 2;
+			/* 0.5 mV * 25 uV = 0.0125 uV resolution. */
+			val *= shunt_resistor;
+			/* Overflow check: Assuming 32-bit val and shunt resistor, val <= 64bits */
+			val = DIV_ROUND_CLOSEST_ULL(val, 25 * 1000) * 2;
+			/* Overflow check: val is now <= 51 bits */
 		}
 		break;
 	case LTC2945_VIN_H:
@@ -208,14 +227,11 @@ static int ltc2945_val_to_reg(struct device *dev, u8 reg,
 	case LTC2945_MIN_SENSE_H:
 	case LTC2945_MAX_SENSE_THRES_H:
 	case LTC2945_MIN_SENSE_THRES_H:
-		/*
-		 * 25 uV resolution. Convert to current as measured with
-		 * an 1 mOhm sense resistor, in mA. If a different sense
-		 * resistor is installed, calculate the actual current by
-		 * dividing the reported current by the sense resistor value
-		 * in mOhm.
-		 */
-		val = DIV_ROUND_CLOSEST(val, 25);
+		/* 25 uV resolution. Convert to  mA. */
+		val *= shunt_resistor;
+		/* Overflow check: Assuming 32-bit val and 32-bit shunt resistor, val is 64bits */
+		val = DIV_ROUND_CLOSEST_ULL(val, 25 * 1000);
+		/* Overflow check: val is now <= 50 bits */
 		break;
 	default:
 		return -EINVAL;
@@ -240,15 +256,16 @@ static ssize_t ltc2945_value_store(struct device *dev,
 				   const char *buf, size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
-	struct regmap *regmap = dev_get_drvdata(dev);
+	struct ltc2945_data *data = dev_get_drvdata(dev);
+	struct regmap *regmap = data->regmap;
 	u8 reg = attr->index;
-	unsigned long val;
+	unsigned int val;
 	u8 regbuf[3];
 	int num_regs;
-	int regval;
+	long long regval;
 	int ret;
 
-	ret = kstrtoul(buf, 10, &val);
+	ret = kstrtouint(buf, 10, &val);
 	if (ret)
 		return ret;
 
@@ -277,7 +294,8 @@ static ssize_t ltc2945_history_store(struct device *dev,
 				     const char *buf, size_t count)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
-	struct regmap *regmap = dev_get_drvdata(dev);
+	struct ltc2945_data *data = dev_get_drvdata(dev);
+	struct regmap *regmap = data->regmap;
 	u8 reg = attr->index;
 	int num_regs = is_power_reg(reg) ? 3 : 2;
 	u8 buf_min[3] = { 0xff, 0xff, 0xff };
@@ -329,7 +347,8 @@ static ssize_t ltc2945_bool_show(struct device *dev,
 				 struct device_attribute *da, char *buf)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
-	struct regmap *regmap = dev_get_drvdata(dev);
+	struct ltc2945_data *data = dev_get_drvdata(dev);
+	struct regmap *regmap = data->regmap;
 	unsigned int fault;
 	int ret;
 
@@ -458,6 +477,12 @@ static int ltc2945_probe(struct i2c_client *client)
 	struct device *dev = &client->dev;
 	struct device *hwmon_dev;
 	struct regmap *regmap;
+	struct ltc2945_data *data;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+	dev_set_drvdata(dev, data);
 
 	regmap = devm_regmap_init_i2c(client, &ltc2945_regmap_config);
 	if (IS_ERR(regmap)) {
@@ -465,11 +490,19 @@ static int ltc2945_probe(struct i2c_client *client)
 		return PTR_ERR(regmap);
 	}
 
+	data->regmap = regmap;
+	if (device_property_read_u32(dev, "shunt-resistor-micro-ohms",
+				     &data->shunt_resistor))
+		data->shunt_resistor = 1000;
+
+	if (data->shunt_resistor == 0)
+		return -EINVAL;
+
 	/* Clear faults */
 	regmap_write(regmap, LTC2945_FAULT, 0x00);
 
 	hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
-							   regmap,
+							   data,
 							   ltc2945_groups);
 	return PTR_ERR_OR_ZERO(hwmon_dev);
 }

-- 
2.25.1


^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH v4 5/5] hwmon: ltc2945: Convert division to DIV_ROUND_CLOSEST_ULL
  2023-01-26 22:32 [PATCH v4 0/5] hwmon: ltc2945: Add binding and shunt resistor support Jonathan Cormier
                   ` (3 preceding siblings ...)
  2023-01-26 22:32 ` [PATCH v4 4/5] hwmon: ltc2945: Allow setting shunt resistor Jonathan Cormier
@ 2023-01-26 22:32 ` Jonathan Cormier
  2023-01-29 19:55   ` Guenter Roeck
  4 siblings, 1 reply; 10+ messages in thread
From: Jonathan Cormier @ 2023-01-26 22:32 UTC (permalink / raw)
  To: Jean Delvare, Guenter Roeck, Rob Herring, Krzysztof Kozlowski
  Cc: linux-hwmon, devicetree, linux-kernel, Bob Duke, John Pruitt,
	Jonathan Cormier

Convert division to DIV_ROUND_CLOSEST_ULL to match code
in same function.

Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
---
 drivers/hwmon/ltc2945.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/hwmon/ltc2945.c b/drivers/hwmon/ltc2945.c
index 0b5e448b4f12..33341d01f1f7 100644
--- a/drivers/hwmon/ltc2945.c
+++ b/drivers/hwmon/ltc2945.c
@@ -212,7 +212,7 @@ static long long ltc2945_val_to_reg(struct device *dev, u8 reg,
 	case LTC2945_MAX_VIN_THRES_H:
 	case LTC2945_MIN_VIN_THRES_H:
 		/* 25 mV resolution. */
-		val /= 25;
+		val = DIV_ROUND_CLOSEST_ULL(val, 25);
 		break;
 	case LTC2945_ADIN_H:
 	case LTC2945_MAX_ADIN_H:

-- 
2.25.1


^ permalink raw reply related	[flat|nested] 10+ messages in thread

* Re: [PATCH v4 5/5] hwmon: ltc2945: Convert division to DIV_ROUND_CLOSEST_ULL
  2023-01-26 22:32 ` [PATCH v4 5/5] hwmon: ltc2945: Convert division to DIV_ROUND_CLOSEST_ULL Jonathan Cormier
@ 2023-01-29 19:55   ` Guenter Roeck
  0 siblings, 0 replies; 10+ messages in thread
From: Guenter Roeck @ 2023-01-29 19:55 UTC (permalink / raw)
  To: Jonathan Cormier
  Cc: Jean Delvare, Rob Herring, Krzysztof Kozlowski, linux-hwmon,
	devicetree, linux-kernel, Bob Duke, John Pruitt

On Thu, Jan 26, 2023 at 05:32:27PM -0500, Jonathan Cormier wrote:
> Convert division to DIV_ROUND_CLOSEST_ULL to match code
> in same function.
> 
> Signed-off-by: Jonathan Cormier <jcormier@criticallink.comi
> ---
>  drivers/hwmon/ltc2945.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/hwmon/ltc2945.c b/drivers/hwmon/ltc2945.c
> index 0b5e448b4f12..33341d01f1f7 100644
> --- a/drivers/hwmon/ltc2945.c
> +++ b/drivers/hwmon/ltc2945.c
> @@ -212,7 +212,7 @@ static long long ltc2945_val_to_reg(struct device *dev, u8 reg,
>  	case LTC2945_MAX_VIN_THRES_H:
>  	case LTC2945_MIN_VIN_THRES_H:
>  		/* 25 mV resolution. */
> -		val /= 25;
> +		val = DIV_ROUND_CLOSEST_ULL(val, 25);

This needs to be combined with the previous patch since that patch changes
'val' from unsigned long to unsigned long long, causing a compile failure
on 32-bit builds.

I'll do that unless some other 32 bit build failure shows up.

Guenter

>  		break;
>  	case LTC2945_ADIN_H:
>  	case LTC2945_MAX_ADIN_H:
> 
> -- 
> 2.25.1
> 

^ permalink raw reply	[flat|nested] 10+ messages in thread

* Re: [PATCH v4 1/5] dt-bindings: hwmon: adi,ltc2945: Add binding
  2023-01-26 22:32 ` [PATCH v4 1/5] dt-bindings: hwmon: adi,ltc2945: Add binding Jonathan Cormier
@ 2023-01-29 20:16   ` Guenter Roeck
  2023-01-30 15:19     ` Jon Cormier
  0 siblings, 1 reply; 10+ messages in thread
From: Guenter Roeck @ 2023-01-29 20:16 UTC (permalink / raw)
  To: Jonathan Cormier
  Cc: Jean Delvare, Rob Herring, Krzysztof Kozlowski, linux-hwmon,
	devicetree, linux-kernel, Bob Duke, John Pruitt,
	Krzysztof Kozlowski

On Thu, Jan 26, 2023 at 05:32:23PM -0500, Jonathan Cormier wrote:
> Create initial binding for the LTC2945 I2C power monitor.
> 
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>

Series applied, after merging patch 4/5 and 5/5 of the series
to avoid spurious 32-bit build failures, and after fixing a
continuation line alignment.

In the future, please run checkpatch --strict on your patches,
and please provide change logs.

Thanks,
Guenter

^ permalink raw reply	[flat|nested] 10+ messages in thread

* Re: [PATCH v4 1/5] dt-bindings: hwmon: adi,ltc2945: Add binding
  2023-01-29 20:16   ` Guenter Roeck
@ 2023-01-30 15:19     ` Jon Cormier
  2023-01-30 15:25       ` Jon Cormier
  0 siblings, 1 reply; 10+ messages in thread
From: Jon Cormier @ 2023-01-30 15:19 UTC (permalink / raw)
  To: Guenter Roeck
  Cc: Jean Delvare, Rob Herring, Krzysztof Kozlowski, linux-hwmon,
	devicetree, linux-kernel, Bob Duke, John Pruitt,
	Krzysztof Kozlowski

On Sun, Jan 29, 2023 at 3:16 PM Guenter Roeck <linux@roeck-us.net> wrote:
>
> On Thu, Jan 26, 2023 at 05:32:23PM -0500, Jonathan Cormier wrote:
> > Create initial binding for the LTC2945 I2C power monitor.
> >
> > Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> > Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
>
> Series applied,
Great
> after merging patch 4/5 and 5/5 of the series
> to avoid spurious 32-bit build failures,
Huh, I split these per request, curious why they'd cause build
failures when separated...
> and after fixing a continuation line alignment.
>
> In the future, please run checkpatch --strict on your patches,
Will do. I didn't know about this option.
> and please provide change logs.
This I did do in every cover letter.
>
> Thanks,
> Guenter

-- 
Jonathan Cormier
Software Engineer

Voice:  315.425.4045 x222



http://www.CriticalLink.com
6712 Brooklawn Parkway, Syracuse, NY 13211

^ permalink raw reply	[flat|nested] 10+ messages in thread

* Re: [PATCH v4 1/5] dt-bindings: hwmon: adi,ltc2945: Add binding
  2023-01-30 15:19     ` Jon Cormier
@ 2023-01-30 15:25       ` Jon Cormier
  0 siblings, 0 replies; 10+ messages in thread
From: Jon Cormier @ 2023-01-30 15:25 UTC (permalink / raw)
  To: Guenter Roeck
  Cc: Jean Delvare, Rob Herring, Krzysztof Kozlowski, linux-hwmon,
	devicetree, linux-kernel, Bob Duke, John Pruitt,
	Krzysztof Kozlowski

On Mon, Jan 30, 2023 at 10:19 AM Jon Cormier <jcormier@criticallink.com> wrote:
>
> On Sun, Jan 29, 2023 at 3:16 PM Guenter Roeck <linux@roeck-us.net> wrote:
> >
> > On Thu, Jan 26, 2023 at 05:32:23PM -0500, Jonathan Cormier wrote:
> > > Create initial binding for the LTC2945 I2C power monitor.
> > >
> > > Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> > > Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
> >
> > Series applied,
> Great
> > after merging patch 4/5 and 5/5 of the series
> > to avoid spurious 32-bit build failures,
> Huh, I split these per request, curious why they'd cause build
> failures when separated...
Nevermind, I see your other response.
> > and after fixing a continuation line alignment.
> >
> > In the future, please run checkpatch --strict on your patches,
> Will do. I didn't know about this option.
> > and please provide change logs.
> This I did do in every cover letter.
> >
> > Thanks,
> > Guenter
>
> --
> Jonathan Cormier
> Software Engineer
>
> Voice:  315.425.4045 x222
>
>
>
> http://www.CriticalLink.com
> 6712 Brooklawn Parkway, Syracuse, NY 13211



-- 
Jonathan Cormier
Software Engineer

Voice:  315.425.4045 x222



http://www.CriticalLink.com
6712 Brooklawn Parkway, Syracuse, NY 13211

^ permalink raw reply	[flat|nested] 10+ messages in thread

end of thread, other threads:[~2023-01-30 15:25 UTC | newest]

Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-01-26 22:32 [PATCH v4 0/5] hwmon: ltc2945: Add binding and shunt resistor support Jonathan Cormier
2023-01-26 22:32 ` [PATCH v4 1/5] dt-bindings: hwmon: adi,ltc2945: Add binding Jonathan Cormier
2023-01-29 20:16   ` Guenter Roeck
2023-01-30 15:19     ` Jon Cormier
2023-01-30 15:25       ` Jon Cormier
2023-01-26 22:32 ` [PATCH v4 2/5] hwmon: ltc2945: Add devicetree match table Jonathan Cormier
2023-01-26 22:32 ` [PATCH v4 3/5] hwmon: ltc2945: Handle error case in ltc2945_value_store Jonathan Cormier
2023-01-26 22:32 ` [PATCH v4 4/5] hwmon: ltc2945: Allow setting shunt resistor Jonathan Cormier
2023-01-26 22:32 ` [PATCH v4 5/5] hwmon: ltc2945: Convert division to DIV_ROUND_CLOSEST_ULL Jonathan Cormier
2023-01-29 19:55   ` Guenter Roeck

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).