* [PATCH] hwmon: (nct6775) Integrated new model nct6116
@ 2019-07-10 19:19 Björn Gerhart
2019-07-10 19:29 ` Björn Gerhart
0 siblings, 1 reply; 12+ messages in thread
From: Björn Gerhart @ 2019-07-10 19:19 UTC (permalink / raw)
To: Hardware Monitoring; +Cc: Guenter Roeck
The nct6116 is the successor model of nct6106. Mainly I’m unsure about my changes related to:
- NCT6116_BEEP_BITS
- int cr24 (cr23 is new, and I’m unsure if the code has to get modified therefore)
- NCT6116_REG_FAN_PULSES
- NCT6116_FAN_PULSE_SHIFT
- NCT6116_ALARM_BITS
With the nct6116 wired on my mainboard, the sensors command seems to work as I would expect.
Index: nct6775.c
===================================================================
--- nct6775.c (revision 16313)
+++ nct6775.c (working copy)
@@ -34,6 +34,7 @@
*
* Chip #vin #fan #pwm #temp chip IDs man ID
* nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
+ * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
* nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
* nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
* nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
@@ -72,12 +73,13 @@
#define USE_ALTERNATE
-enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
- nct6795, nct6796, nct6797, nct6798 };
+enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
+ nct6793, nct6795, nct6796, nct6797, nct6798 };
/* used to set data->name = nct6775_device_names[data->sio_kind] */
static const char * const nct6775_device_names[] = {
"nct6106",
+ "nct6116",
"nct6775",
"nct6776",
"nct6779",
@@ -92,6 +94,7 @@
static const char * const nct6775_sio_names[] __initconst = {
"NCT6106D",
+ "NCT6116D",
"NCT6775F",
"NCT6776D/F",
"NCT6779D",
@@ -129,6 +132,7 @@
#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
#define SIO_NCT6106_ID 0xc450
+#define SIO_NCT6116_ID 0xd280
#define SIO_NCT6775_ID 0xb470
#define SIO_NCT6776_ID 0xc330
#define SIO_NCT6779_ID 0xc560
@@ -819,18 +823,29 @@
0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x07, 0x08, 0x09 };
static const u16 NCT6106_REG_TEMP[] = { 0x10, 0x11, 0x12, 0x13, 0x14, 0x15 };
+static const u16 NCT6116_REG_TEMP[] = { 0x10, 0x11, 0x12 };
static const u16 NCT6106_REG_TEMP_MON[] = { 0x18, 0x19, 0x1a };
static const u16 NCT6106_REG_TEMP_HYST[] = {
0xc3, 0xc7, 0xcb, 0xcf, 0xd3, 0xd7 };
+static const u16 NCT6116_REG_TEMP_HYST[] = {
+ 0xc3, 0xc7, 0xcb };
static const u16 NCT6106_REG_TEMP_OVER[] = {
0xc2, 0xc6, 0xca, 0xce, 0xd2, 0xd6 };
+static const u16 NCT6116_REG_TEMP_OVER[] = {
+ 0xc2, 0xc6, 0xca };
static const u16 NCT6106_REG_TEMP_CRIT_L[] = {
0xc0, 0xc4, 0xc8, 0xcc, 0xd0, 0xd4 };
+static const u16 NCT6116_REG_TEMP_CRIT_L[] = {
+ 0xc0, 0xc4, 0xc8 };
static const u16 NCT6106_REG_TEMP_CRIT_H[] = {
0xc1, 0xc5, 0xc9, 0xcf, 0xd1, 0xd5 };
+static const u16 NCT6116_REG_TEMP_CRIT_H[] = {
+ 0xc1, 0xc5, 0xc9 };
static const u16 NCT6106_REG_TEMP_OFFSET[] = { 0x311, 0x312, 0x313 };
static const u16 NCT6106_REG_TEMP_CONFIG[] = {
0xb7, 0xb8, 0xb9, 0xba, 0xbb, 0xbc };
+static const u16 NCT6116_REG_TEMP_CONFIG[] = {
+ 0xb7, 0xb8, 0xb9 };
static const u16 NCT6106_REG_FAN[] = { 0x20, 0x22, 0x24 };
static const u16 NCT6106_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4 };
@@ -845,6 +860,8 @@
static const u16 NCT6106_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130 };
static const u16 NCT6106_REG_TEMP_SOURCE[] = {
0xb0, 0xb1, 0xb2, 0xb3, 0xb4, 0xb5 };
+static const u16 NCT6116_REG_TEMP_SOURCE[] = {
+ 0xb0, 0xb1, 0xb2 };
static const u16 NCT6106_REG_CRITICAL_TEMP[] = { 0x11a, 0x12a, 0x13a };
static const u16 NCT6106_REG_CRITICAL_TEMP_TOLERANCE[] = {
@@ -886,6 +903,16 @@
48, -1 /* intrusion0, intrusion1 */
};
+static const s8 NCT6116_ALARM_BITS[] = {
+ 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
+ 9, -1, -1, -1, -1, -1, -1, /* in8..in14 */
+ -1, /* unused */
+ 32, 33, 34, -1, -1, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 16, 17, 18, /* temp1..temp3 */
+ 48, -1 /* intrusion0, intrusion1 */
+};
+
static const u16 NCT6106_REG_BEEP[NUM_REG_BEEP] = {
0x3c0, 0x3c1, 0x3c2, 0x3c3, 0x3c4 };
@@ -1308,6 +1335,10 @@
return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
reg == 0x111 || reg == 0x121 || reg == 0x131;
+ case nct6116:
+ return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
+ reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
+ reg == 0x111 || reg == 0x121 || reg == 0x131;
case nct6775:
return (((reg & 0xff00) == 0x100 ||
(reg & 0xff00) == 0x200) &&
@@ -1687,6 +1718,7 @@
data->auto_pwm[i][data->auto_pwm_num] = 0xff;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3123,6 +3155,7 @@
case nct6776:
break; /* always enabled, nothing to do */
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3549,6 +3582,11 @@
fan3pin = !(cr24 & 0x80);
pwm3pin = cr24 & 0x08;
+ } else if (data->kind == nct6116) {
+ int cr24 = superio_inb(sioreg, 0x24);
+
+ fan3pin = !(cr24 & 0x80);
+ pwm3pin = cr24 & 0x08;
} else {
/*
* NCT6779D, NCT6791D, NCT6792D, NCT6793D, NCT6795D, NCT6796D,
@@ -3820,6 +3858,78 @@
reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
break;
+ case nct6116:
+ data->in_num = 9;
+ data->pwm_num = 3;
+ data->auto_pwm_num = 4;
+ data->temp_fixed_num = 3;
+ data->num_temp_alarms = 3;
+ data->num_temp_beeps = 3;
+
+ data->fan_from_reg = fan_from_reg13;
+ data->fan_from_reg_min = fan_from_reg13;
+
+ data->temp_label = nct6776_temp_label;
+ data->temp_mask = NCT6776_TEMP_MASK;
+ data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
+
+ data->REG_VBAT = NCT6106_REG_VBAT;
+ data->REG_DIODE = NCT6106_REG_DIODE;
+ data->DIODE_MASK = NCT6106_DIODE_MASK;
+ data->REG_VIN = NCT6106_REG_IN;
+ data->REG_IN_MINMAX[0] = NCT6106_REG_IN_MIN;
+ data->REG_IN_MINMAX[1] = NCT6106_REG_IN_MAX;
+ data->REG_TARGET = NCT6106_REG_TARGET;
+ data->REG_FAN = NCT6106_REG_FAN;
+ data->REG_FAN_MODE = NCT6106_REG_FAN_MODE;
+ data->REG_FAN_MIN = NCT6106_REG_FAN_MIN;
+ data->REG_FAN_PULSES = NCT6106_REG_FAN_PULSES;
+ data->FAN_PULSE_SHIFT = NCT6106_FAN_PULSE_SHIFT;
+ data->REG_FAN_TIME[0] = NCT6106_REG_FAN_STOP_TIME;
+ data->REG_FAN_TIME[1] = NCT6106_REG_FAN_STEP_UP_TIME;
+ data->REG_FAN_TIME[2] = NCT6106_REG_FAN_STEP_DOWN_TIME;
+ data->REG_PWM[0] = NCT6106_REG_PWM;
+ data->REG_PWM[1] = NCT6106_REG_FAN_START_OUTPUT;
+ data->REG_PWM[2] = NCT6106_REG_FAN_STOP_OUTPUT;
+ data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
+ data->REG_PWM[6] = NCT6106_REG_WEIGHT_DUTY_BASE;
+ data->REG_PWM_READ = NCT6106_REG_PWM_READ;
+ data->REG_PWM_MODE = NCT6106_REG_PWM_MODE;
+ data->PWM_MODE_MASK = NCT6106_PWM_MODE_MASK;
+ data->REG_AUTO_TEMP = NCT6106_REG_AUTO_TEMP;
+ data->REG_AUTO_PWM = NCT6106_REG_AUTO_PWM;
+ data->REG_CRITICAL_TEMP = NCT6106_REG_CRITICAL_TEMP;
+ data->REG_CRITICAL_TEMP_TOLERANCE
+ = NCT6106_REG_CRITICAL_TEMP_TOLERANCE;
+ data->REG_CRITICAL_PWM_ENABLE = NCT6106_REG_CRITICAL_PWM_ENABLE;
+ data->CRITICAL_PWM_ENABLE_MASK
+ = NCT6106_CRITICAL_PWM_ENABLE_MASK;
+ data->REG_CRITICAL_PWM = NCT6106_REG_CRITICAL_PWM;
+ data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
+ data->REG_TEMP_SOURCE = NCT6116_REG_TEMP_SOURCE;
+ data->REG_TEMP_SEL = NCT6106_REG_TEMP_SEL;
+ data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
+ data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
+ data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
+ data->REG_WEIGHT_TEMP[2] = NCT6106_REG_WEIGHT_TEMP_BASE;
+ data->REG_ALARM = NCT6106_REG_ALARM;
+ data->ALARM_BITS = NCT6116_ALARM_BITS;
+ data->REG_BEEP = NCT6106_REG_BEEP;
+ data->BEEP_BITS = NCT6106_BEEP_BITS;
+
+ reg_temp = NCT6116_REG_TEMP;
+ reg_temp_mon = NCT6106_REG_TEMP_MON;
+ num_reg_temp = ARRAY_SIZE(NCT6116_REG_TEMP);
+ num_reg_temp_mon = ARRAY_SIZE(NCT6106_REG_TEMP_MON);
+ reg_temp_over = NCT6116_REG_TEMP_OVER;
+ reg_temp_hyst = NCT6116_REG_TEMP_HYST;
+ reg_temp_config = NCT6116_REG_TEMP_CONFIG;
+ reg_temp_alternate = NCT6106_REG_TEMP_ALTERNATE;
+ reg_temp_crit = NCT6106_REG_TEMP_CRIT;
+ reg_temp_crit_l = NCT6116_REG_TEMP_CRIT_L;
+ reg_temp_crit_h = NCT6116_REG_TEMP_CRIT_H;
+
+ break;
case nct6775:
data->in_num = 9;
data->pwm_num = 3;
@@ -4365,6 +4475,7 @@
data->have_vid = (cr2a & 0x60) == 0x40;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -4396,6 +4507,9 @@
case nct6106:
tmp |= 0xe0;
break;
+ case nct6116:
+ tmp |= 0xe0;
+ break;
case nct6775:
tmp |= 0x1e;
break;
@@ -4589,6 +4703,9 @@
case SIO_NCT6106_ID:
sio_data->kind = nct6106;
break;
+ case SIO_NCT6116_ID:
+ sio_data->kind = nct6116;
+ break;
case SIO_NCT6775_ID:
sio_data->kind = nct6775;
break;
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-10 19:19 [PATCH] hwmon: (nct6775) Integrated new model nct6116 Björn Gerhart
@ 2019-07-10 19:29 ` Björn Gerhart
2019-07-10 20:38 ` Guenter Roeck
0 siblings, 1 reply; 12+ messages in thread
From: Björn Gerhart @ 2019-07-10 19:29 UTC (permalink / raw)
To: Hardware Monitoring; +Cc: Guenter Roeck
oh no, the patch is WRONG as I noticed right now. Sorry for the noise! I’ll re-work it and come back!
> Am 10.07.2019 um 21:19 schrieb Björn Gerhart <gerhart@posteo.de>:
>
> The nct6116 is the successor model of nct6106. Mainly I’m unsure about my changes related to:
> - NCT6116_BEEP_BITS
> - int cr24 (cr23 is new, and I’m unsure if the code has to get modified therefore)
> - NCT6116_REG_FAN_PULSES
> - NCT6116_FAN_PULSE_SHIFT
> - NCT6116_ALARM_BITS
>
> With the nct6116 wired on my mainboard, the sensors command seems to work as I would expect.
>
> Index: nct6775.c
> ===================================================================
> --- nct6775.c (revision 16313)
> +++ nct6775.c (working copy)
> @@ -34,6 +34,7 @@
> *
> * Chip #vin #fan #pwm #temp chip IDs man ID
> * nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
> + * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
> * nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
> * nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
> * nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
> @@ -72,12 +73,13 @@
>
> #define USE_ALTERNATE
>
> -enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
> - nct6795, nct6796, nct6797, nct6798 };
> +enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
> + nct6793, nct6795, nct6796, nct6797, nct6798 };
>
> /* used to set data->name = nct6775_device_names[data->sio_kind] */
> static const char * const nct6775_device_names[] = {
> "nct6106",
> + "nct6116",
> "nct6775",
> "nct6776",
> "nct6779",
> @@ -92,6 +94,7 @@
>
> static const char * const nct6775_sio_names[] __initconst = {
> "NCT6106D",
> + "NCT6116D",
> "NCT6775F",
> "NCT6776D/F",
> "NCT6779D",
> @@ -129,6 +132,7 @@
> #define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
>
> #define SIO_NCT6106_ID 0xc450
> +#define SIO_NCT6116_ID 0xd280
> #define SIO_NCT6775_ID 0xb470
> #define SIO_NCT6776_ID 0xc330
> #define SIO_NCT6779_ID 0xc560
> @@ -819,18 +823,29 @@
> 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x07, 0x08, 0x09 };
>
> static const u16 NCT6106_REG_TEMP[] = { 0x10, 0x11, 0x12, 0x13, 0x14, 0x15 };
> +static const u16 NCT6116_REG_TEMP[] = { 0x10, 0x11, 0x12 };
> static const u16 NCT6106_REG_TEMP_MON[] = { 0x18, 0x19, 0x1a };
> static const u16 NCT6106_REG_TEMP_HYST[] = {
> 0xc3, 0xc7, 0xcb, 0xcf, 0xd3, 0xd7 };
> +static const u16 NCT6116_REG_TEMP_HYST[] = {
> + 0xc3, 0xc7, 0xcb };
> static const u16 NCT6106_REG_TEMP_OVER[] = {
> 0xc2, 0xc6, 0xca, 0xce, 0xd2, 0xd6 };
> +static const u16 NCT6116_REG_TEMP_OVER[] = {
> + 0xc2, 0xc6, 0xca };
> static const u16 NCT6106_REG_TEMP_CRIT_L[] = {
> 0xc0, 0xc4, 0xc8, 0xcc, 0xd0, 0xd4 };
> +static const u16 NCT6116_REG_TEMP_CRIT_L[] = {
> + 0xc0, 0xc4, 0xc8 };
> static const u16 NCT6106_REG_TEMP_CRIT_H[] = {
> 0xc1, 0xc5, 0xc9, 0xcf, 0xd1, 0xd5 };
> +static const u16 NCT6116_REG_TEMP_CRIT_H[] = {
> + 0xc1, 0xc5, 0xc9 };
> static const u16 NCT6106_REG_TEMP_OFFSET[] = { 0x311, 0x312, 0x313 };
> static const u16 NCT6106_REG_TEMP_CONFIG[] = {
> 0xb7, 0xb8, 0xb9, 0xba, 0xbb, 0xbc };
> +static const u16 NCT6116_REG_TEMP_CONFIG[] = {
> + 0xb7, 0xb8, 0xb9 };
>
> static const u16 NCT6106_REG_FAN[] = { 0x20, 0x22, 0x24 };
> static const u16 NCT6106_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4 };
> @@ -845,6 +860,8 @@
> static const u16 NCT6106_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130 };
> static const u16 NCT6106_REG_TEMP_SOURCE[] = {
> 0xb0, 0xb1, 0xb2, 0xb3, 0xb4, 0xb5 };
> +static const u16 NCT6116_REG_TEMP_SOURCE[] = {
> + 0xb0, 0xb1, 0xb2 };
>
> static const u16 NCT6106_REG_CRITICAL_TEMP[] = { 0x11a, 0x12a, 0x13a };
> static const u16 NCT6106_REG_CRITICAL_TEMP_TOLERANCE[] = {
> @@ -886,6 +903,16 @@
> 48, -1 /* intrusion0, intrusion1 */
> };
>
> +static const s8 NCT6116_ALARM_BITS[] = {
> + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
> + 9, -1, -1, -1, -1, -1, -1, /* in8..in14 */
> + -1, /* unused */
> + 32, 33, 34, -1, -1, /* fan1..fan5 */
> + -1, -1, -1, /* unused */
> + 16, 17, 18, /* temp1..temp3 */
> + 48, -1 /* intrusion0, intrusion1 */
> +};
> +
> static const u16 NCT6106_REG_BEEP[NUM_REG_BEEP] = {
> 0x3c0, 0x3c1, 0x3c2, 0x3c3, 0x3c4 };
>
> @@ -1308,6 +1335,10 @@
> return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
> reg == 0x111 || reg == 0x121 || reg == 0x131;
> + case nct6116:
> + return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> + reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
> + reg == 0x111 || reg == 0x121 || reg == 0x131;
> case nct6775:
> return (((reg & 0xff00) == 0x100 ||
> (reg & 0xff00) == 0x200) &&
> @@ -1687,6 +1718,7 @@
> data->auto_pwm[i][data->auto_pwm_num] = 0xff;
> break;
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -3123,6 +3155,7 @@
> case nct6776:
> break; /* always enabled, nothing to do */
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -3549,6 +3582,11 @@
>
> fan3pin = !(cr24 & 0x80);
> pwm3pin = cr24 & 0x08;
> + } else if (data->kind == nct6116) {
> + int cr24 = superio_inb(sioreg, 0x24);
> +
> + fan3pin = !(cr24 & 0x80);
> + pwm3pin = cr24 & 0x08;
> } else {
> /*
> * NCT6779D, NCT6791D, NCT6792D, NCT6793D, NCT6795D, NCT6796D,
> @@ -3820,6 +3858,78 @@
> reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
>
> break;
> + case nct6116:
> + data->in_num = 9;
> + data->pwm_num = 3;
> + data->auto_pwm_num = 4;
> + data->temp_fixed_num = 3;
> + data->num_temp_alarms = 3;
> + data->num_temp_beeps = 3;
> +
> + data->fan_from_reg = fan_from_reg13;
> + data->fan_from_reg_min = fan_from_reg13;
> +
> + data->temp_label = nct6776_temp_label;
> + data->temp_mask = NCT6776_TEMP_MASK;
> + data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
> +
> + data->REG_VBAT = NCT6106_REG_VBAT;
> + data->REG_DIODE = NCT6106_REG_DIODE;
> + data->DIODE_MASK = NCT6106_DIODE_MASK;
> + data->REG_VIN = NCT6106_REG_IN;
> + data->REG_IN_MINMAX[0] = NCT6106_REG_IN_MIN;
> + data->REG_IN_MINMAX[1] = NCT6106_REG_IN_MAX;
> + data->REG_TARGET = NCT6106_REG_TARGET;
> + data->REG_FAN = NCT6106_REG_FAN;
> + data->REG_FAN_MODE = NCT6106_REG_FAN_MODE;
> + data->REG_FAN_MIN = NCT6106_REG_FAN_MIN;
> + data->REG_FAN_PULSES = NCT6106_REG_FAN_PULSES;
> + data->FAN_PULSE_SHIFT = NCT6106_FAN_PULSE_SHIFT;
> + data->REG_FAN_TIME[0] = NCT6106_REG_FAN_STOP_TIME;
> + data->REG_FAN_TIME[1] = NCT6106_REG_FAN_STEP_UP_TIME;
> + data->REG_FAN_TIME[2] = NCT6106_REG_FAN_STEP_DOWN_TIME;
> + data->REG_PWM[0] = NCT6106_REG_PWM;
> + data->REG_PWM[1] = NCT6106_REG_FAN_START_OUTPUT;
> + data->REG_PWM[2] = NCT6106_REG_FAN_STOP_OUTPUT;
> + data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
> + data->REG_PWM[6] = NCT6106_REG_WEIGHT_DUTY_BASE;
> + data->REG_PWM_READ = NCT6106_REG_PWM_READ;
> + data->REG_PWM_MODE = NCT6106_REG_PWM_MODE;
> + data->PWM_MODE_MASK = NCT6106_PWM_MODE_MASK;
> + data->REG_AUTO_TEMP = NCT6106_REG_AUTO_TEMP;
> + data->REG_AUTO_PWM = NCT6106_REG_AUTO_PWM;
> + data->REG_CRITICAL_TEMP = NCT6106_REG_CRITICAL_TEMP;
> + data->REG_CRITICAL_TEMP_TOLERANCE
> + = NCT6106_REG_CRITICAL_TEMP_TOLERANCE;
> + data->REG_CRITICAL_PWM_ENABLE = NCT6106_REG_CRITICAL_PWM_ENABLE;
> + data->CRITICAL_PWM_ENABLE_MASK
> + = NCT6106_CRITICAL_PWM_ENABLE_MASK;
> + data->REG_CRITICAL_PWM = NCT6106_REG_CRITICAL_PWM;
> + data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
> + data->REG_TEMP_SOURCE = NCT6116_REG_TEMP_SOURCE;
> + data->REG_TEMP_SEL = NCT6106_REG_TEMP_SEL;
> + data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
> + data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
> + data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
> + data->REG_WEIGHT_TEMP[2] = NCT6106_REG_WEIGHT_TEMP_BASE;
> + data->REG_ALARM = NCT6106_REG_ALARM;
> + data->ALARM_BITS = NCT6116_ALARM_BITS;
> + data->REG_BEEP = NCT6106_REG_BEEP;
> + data->BEEP_BITS = NCT6106_BEEP_BITS;
> +
> + reg_temp = NCT6116_REG_TEMP;
> + reg_temp_mon = NCT6106_REG_TEMP_MON;
> + num_reg_temp = ARRAY_SIZE(NCT6116_REG_TEMP);
> + num_reg_temp_mon = ARRAY_SIZE(NCT6106_REG_TEMP_MON);
> + reg_temp_over = NCT6116_REG_TEMP_OVER;
> + reg_temp_hyst = NCT6116_REG_TEMP_HYST;
> + reg_temp_config = NCT6116_REG_TEMP_CONFIG;
> + reg_temp_alternate = NCT6106_REG_TEMP_ALTERNATE;
> + reg_temp_crit = NCT6106_REG_TEMP_CRIT;
> + reg_temp_crit_l = NCT6116_REG_TEMP_CRIT_L;
> + reg_temp_crit_h = NCT6116_REG_TEMP_CRIT_H;
> +
> + break;
> case nct6775:
> data->in_num = 9;
> data->pwm_num = 3;
> @@ -4365,6 +4475,7 @@
> data->have_vid = (cr2a & 0x60) == 0x40;
> break;
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -4396,6 +4507,9 @@
> case nct6106:
> tmp |= 0xe0;
> break;
> + case nct6116:
> + tmp |= 0xe0;
> + break;
> case nct6775:
> tmp |= 0x1e;
> break;
> @@ -4589,6 +4703,9 @@
> case SIO_NCT6106_ID:
> sio_data->kind = nct6106;
> break;
> + case SIO_NCT6116_ID:
> + sio_data->kind = nct6116;
> + break;
> case SIO_NCT6775_ID:
> sio_data->kind = nct6775;
> break;
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-10 19:29 ` Björn Gerhart
@ 2019-07-10 20:38 ` Guenter Roeck
0 siblings, 0 replies; 12+ messages in thread
From: Guenter Roeck @ 2019-07-10 20:38 UTC (permalink / raw)
To: Björn Gerhart; +Cc: Hardware Monitoring
On Wed, Jul 10, 2019 at 09:29:55PM +0200, Björn Gerhart wrote:
> oh no, the patch is WRONG as I noticed right now. Sorry for the noise! I’ll re-work it and come back!
>
Now I have to figure out what you mean ;-).
Couple of comments anyway below.
Guenter
> > Am 10.07.2019 um 21:19 schrieb Björn Gerhart <gerhart@posteo.de>:
> >
> > The nct6116 is the successor model of nct6106. Mainly I’m unsure about my changes related to:
> > - NCT6116_BEEP_BITS
> > - int cr24 (cr23 is new, and I’m unsure if the code has to get modified therefore)
> > - NCT6116_REG_FAN_PULSES
> > - NCT6116_FAN_PULSE_SHIFT
> > - NCT6116_ALARM_BITS
> >
> > With the nct6116 wired on my mainboard, the sensors command seems to work as I would expect.
> >
> > Index: nct6775.c
> > ===================================================================
> > --- nct6775.c (revision 16313)
> > +++ nct6775.c (working copy)
> > @@ -34,6 +34,7 @@
> > *
> > * Chip #vin #fan #pwm #temp chip IDs man ID
> > * nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
> > + * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
> > * nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
> > * nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
> > * nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
> > @@ -72,12 +73,13 @@
> >
> > #define USE_ALTERNATE
> >
> > -enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
> > - nct6795, nct6796, nct6797, nct6798 };
> > +enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
> > + nct6793, nct6795, nct6796, nct6797, nct6798 };
> >
> > /* used to set data->name = nct6775_device_names[data->sio_kind] */
> > static const char * const nct6775_device_names[] = {
> > "nct6106",
> > + "nct6116",
> > "nct6775",
> > "nct6776",
> > "nct6779",
> > @@ -92,6 +94,7 @@
> >
> > static const char * const nct6775_sio_names[] __initconst = {
> > "NCT6106D",
> > + "NCT6116D",
> > "NCT6775F",
> > "NCT6776D/F",
> > "NCT6779D",
> > @@ -129,6 +132,7 @@
> > #define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
> >
> > #define SIO_NCT6106_ID 0xc450
> > +#define SIO_NCT6116_ID 0xd280
> > #define SIO_NCT6775_ID 0xb470
> > #define SIO_NCT6776_ID 0xc330
> > #define SIO_NCT6779_ID 0xc560
> > @@ -819,18 +823,29 @@
> > 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x07, 0x08, 0x09 };
> >
> > static const u16 NCT6106_REG_TEMP[] = { 0x10, 0x11, 0x12, 0x13, 0x14, 0x15 };
> > +static const u16 NCT6116_REG_TEMP[] = { 0x10, 0x11, 0x12 };
> > static const u16 NCT6106_REG_TEMP_MON[] = { 0x18, 0x19, 0x1a };
> > static const u16 NCT6106_REG_TEMP_HYST[] = {
> > 0xc3, 0xc7, 0xcb, 0xcf, 0xd3, 0xd7 };
> > +static const u16 NCT6116_REG_TEMP_HYST[] = {
> > + 0xc3, 0xc7, 0xcb };
Please move all NCT6116 related declarations/defines together.
> > static const u16 NCT6106_REG_TEMP_OVER[] = {
> > 0xc2, 0xc6, 0xca, 0xce, 0xd2, 0xd6 };
> > +static const u16 NCT6116_REG_TEMP_OVER[] = {
> > + 0xc2, 0xc6, 0xca };
> > static const u16 NCT6106_REG_TEMP_CRIT_L[] = {
> > 0xc0, 0xc4, 0xc8, 0xcc, 0xd0, 0xd4 };
> > +static const u16 NCT6116_REG_TEMP_CRIT_L[] = {
> > + 0xc0, 0xc4, 0xc8 };
> > static const u16 NCT6106_REG_TEMP_CRIT_H[] = {
> > 0xc1, 0xc5, 0xc9, 0xcf, 0xd1, 0xd5 };
> > +static const u16 NCT6116_REG_TEMP_CRIT_H[] = {
> > + 0xc1, 0xc5, 0xc9 };
> > static const u16 NCT6106_REG_TEMP_OFFSET[] = { 0x311, 0x312, 0x313 };
> > static const u16 NCT6106_REG_TEMP_CONFIG[] = {
> > 0xb7, 0xb8, 0xb9, 0xba, 0xbb, 0xbc };
> > +static const u16 NCT6116_REG_TEMP_CONFIG[] = {
> > + 0xb7, 0xb8, 0xb9 };
> >
> > static const u16 NCT6106_REG_FAN[] = { 0x20, 0x22, 0x24 };
> > static const u16 NCT6106_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4 };
> > @@ -845,6 +860,8 @@
> > static const u16 NCT6106_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130 };
> > static const u16 NCT6106_REG_TEMP_SOURCE[] = {
> > 0xb0, 0xb1, 0xb2, 0xb3, 0xb4, 0xb5 };
> > +static const u16 NCT6116_REG_TEMP_SOURCE[] = {
> > + 0xb0, 0xb1, 0xb2 };
> >
> > static const u16 NCT6106_REG_CRITICAL_TEMP[] = { 0x11a, 0x12a, 0x13a };
> > static const u16 NCT6106_REG_CRITICAL_TEMP_TOLERANCE[] = {
> > @@ -886,6 +903,16 @@
> > 48, -1 /* intrusion0, intrusion1 */
> > };
> >
> > +static const s8 NCT6116_ALARM_BITS[] = {
> > + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
> > + 9, -1, -1, -1, -1, -1, -1, /* in8..in14 */
> > + -1, /* unused */
> > + 32, 33, 34, -1, -1, /* fan1..fan5 */
> > + -1, -1, -1, /* unused */
> > + 16, 17, 18, /* temp1..temp3 */
> > + 48, -1 /* intrusion0, intrusion1 */
> > +};
> > +
> > static const u16 NCT6106_REG_BEEP[NUM_REG_BEEP] = {
> > 0x3c0, 0x3c1, 0x3c2, 0x3c3, 0x3c4 };
> >
> > @@ -1308,6 +1335,10 @@
> > return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> > reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
> > reg == 0x111 || reg == 0x121 || reg == 0x131;
> > + case nct6116:
> > + return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> > + reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
> > + reg == 0x111 || reg == 0x121 || reg == 0x131;
Same as case statement for nct6106; please merge.
> > case nct6775:
> > return (((reg & 0xff00) == 0x100 ||
> > (reg & 0xff00) == 0x200) &&
> > @@ -1687,6 +1718,7 @@
> > data->auto_pwm[i][data->auto_pwm_num] = 0xff;
> > break;
> > case nct6106:
> > + case nct6116:
> > case nct6779:
> > case nct6791:
> > case nct6792:
> > @@ -3123,6 +3155,7 @@
> > case nct6776:
> > break; /* always enabled, nothing to do */
> > case nct6106:
> > + case nct6116:
> > case nct6779:
> > case nct6791:
> > case nct6792:
> > @@ -3549,6 +3582,11 @@
> >
> > fan3pin = !(cr24 & 0x80);
> > pwm3pin = cr24 & 0x08;
> > + } else if (data->kind == nct6116) {
> > + int cr24 = superio_inb(sioreg, 0x24);
> > +
> > + fan3pin = !(cr24 & 0x80);
> > + pwm3pin = cr24 & 0x08;
This is the same as the if statement for nct6106. Please merge into a single
if statement.
> > } else {
> > /*
> > * NCT6779D, NCT6791D, NCT6792D, NCT6793D, NCT6795D, NCT6796D,
> > @@ -3820,6 +3858,78 @@
> > reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
> >
> > break;
> > + case nct6116:
> > + data->in_num = 9;
> > + data->pwm_num = 3;
> > + data->auto_pwm_num = 4;
> > + data->temp_fixed_num = 3;
> > + data->num_temp_alarms = 3;
> > + data->num_temp_beeps = 3;
> > +
> > + data->fan_from_reg = fan_from_reg13;
> > + data->fan_from_reg_min = fan_from_reg13;
> > +
> > + data->temp_label = nct6776_temp_label;
> > + data->temp_mask = NCT6776_TEMP_MASK;
> > + data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
> > +
> > + data->REG_VBAT = NCT6106_REG_VBAT;
> > + data->REG_DIODE = NCT6106_REG_DIODE;
> > + data->DIODE_MASK = NCT6106_DIODE_MASK;
> > + data->REG_VIN = NCT6106_REG_IN;
> > + data->REG_IN_MINMAX[0] = NCT6106_REG_IN_MIN;
> > + data->REG_IN_MINMAX[1] = NCT6106_REG_IN_MAX;
> > + data->REG_TARGET = NCT6106_REG_TARGET;
> > + data->REG_FAN = NCT6106_REG_FAN;
> > + data->REG_FAN_MODE = NCT6106_REG_FAN_MODE;
> > + data->REG_FAN_MIN = NCT6106_REG_FAN_MIN;
> > + data->REG_FAN_PULSES = NCT6106_REG_FAN_PULSES;
> > + data->FAN_PULSE_SHIFT = NCT6106_FAN_PULSE_SHIFT;
> > + data->REG_FAN_TIME[0] = NCT6106_REG_FAN_STOP_TIME;
> > + data->REG_FAN_TIME[1] = NCT6106_REG_FAN_STEP_UP_TIME;
> > + data->REG_FAN_TIME[2] = NCT6106_REG_FAN_STEP_DOWN_TIME;
> > + data->REG_PWM[0] = NCT6106_REG_PWM;
> > + data->REG_PWM[1] = NCT6106_REG_FAN_START_OUTPUT;
> > + data->REG_PWM[2] = NCT6106_REG_FAN_STOP_OUTPUT;
> > + data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
> > + data->REG_PWM[6] = NCT6106_REG_WEIGHT_DUTY_BASE;
> > + data->REG_PWM_READ = NCT6106_REG_PWM_READ;
> > + data->REG_PWM_MODE = NCT6106_REG_PWM_MODE;
> > + data->PWM_MODE_MASK = NCT6106_PWM_MODE_MASK;
> > + data->REG_AUTO_TEMP = NCT6106_REG_AUTO_TEMP;
> > + data->REG_AUTO_PWM = NCT6106_REG_AUTO_PWM;
> > + data->REG_CRITICAL_TEMP = NCT6106_REG_CRITICAL_TEMP;
> > + data->REG_CRITICAL_TEMP_TOLERANCE
> > + = NCT6106_REG_CRITICAL_TEMP_TOLERANCE;
> > + data->REG_CRITICAL_PWM_ENABLE = NCT6106_REG_CRITICAL_PWM_ENABLE;
> > + data->CRITICAL_PWM_ENABLE_MASK
> > + = NCT6106_CRITICAL_PWM_ENABLE_MASK;
> > + data->REG_CRITICAL_PWM = NCT6106_REG_CRITICAL_PWM;
> > + data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
> > + data->REG_TEMP_SOURCE = NCT6116_REG_TEMP_SOURCE;
> > + data->REG_TEMP_SEL = NCT6106_REG_TEMP_SEL;
> > + data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
> > + data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
> > + data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
> > + data->REG_WEIGHT_TEMP[2] = NCT6106_REG_WEIGHT_TEMP_BASE;
> > + data->REG_ALARM = NCT6106_REG_ALARM;
> > + data->ALARM_BITS = NCT6116_ALARM_BITS;
> > + data->REG_BEEP = NCT6106_REG_BEEP;
> > + data->BEEP_BITS = NCT6106_BEEP_BITS;
> > +
> > + reg_temp = NCT6116_REG_TEMP;
> > + reg_temp_mon = NCT6106_REG_TEMP_MON;
> > + num_reg_temp = ARRAY_SIZE(NCT6116_REG_TEMP);
> > + num_reg_temp_mon = ARRAY_SIZE(NCT6106_REG_TEMP_MON);
> > + reg_temp_over = NCT6116_REG_TEMP_OVER;
> > + reg_temp_hyst = NCT6116_REG_TEMP_HYST;
> > + reg_temp_config = NCT6116_REG_TEMP_CONFIG;
> > + reg_temp_alternate = NCT6106_REG_TEMP_ALTERNATE;
> > + reg_temp_crit = NCT6106_REG_TEMP_CRIT;
> > + reg_temp_crit_l = NCT6116_REG_TEMP_CRIT_L;
> > + reg_temp_crit_h = NCT6116_REG_TEMP_CRIT_H;
> > +
> > + break;
> > case nct6775:
> > data->in_num = 9;
> > data->pwm_num = 3;
> > @@ -4365,6 +4475,7 @@
> > data->have_vid = (cr2a & 0x60) == 0x40;
> > break;
> > case nct6106:
> > + case nct6116:
> > case nct6779:
> > case nct6791:
> > case nct6792:
> > @@ -4396,6 +4507,9 @@
> > case nct6106:
> > tmp |= 0xe0;
> > break;
> > + case nct6116:
> > + tmp |= 0xe0;
> > + break;
Identical code; please merge with nct6106 case.
> > case nct6775:
> > tmp |= 0x1e;
> > break;
> > @@ -4589,6 +4703,9 @@
> > case SIO_NCT6106_ID:
> > sio_data->kind = nct6106;
> > break;
> > + case SIO_NCT6116_ID:
> > + sio_data->kind = nct6116;
> > + break;
> > case SIO_NCT6775_ID:
> > sio_data->kind = nct6775;
> > break;
> >
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-23 16:06 ` Björn Gerhart
@ 2019-07-23 16:23 ` Guenter Roeck
0 siblings, 0 replies; 12+ messages in thread
From: Guenter Roeck @ 2019-07-23 16:23 UTC (permalink / raw)
To: Björn Gerhart; +Cc: Hardware Monitoring
On Tue, Jul 23, 2019 at 06:06:46PM +0200, Björn Gerhart wrote:
> Thanks for the review Guenter, I checked your proposals. Here comes an update of the patch, and I hope this time the format fits as it should.
>
> Changes:
> - simplified differences in register addresses
> - although kept NCT6116_REG_TEMP_SOURCE, because otherwise the module
> throughs „Invalid temperature source“ messages on loading for each
> register not available
> - fixed fan enablements
> - simplified case statement (fall through)
>
> Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
This version looks good. Applied to hwmon-next.
Thanks!
Guenter
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-19 19:37 ` Guenter Roeck
2019-07-22 17:46 ` Björn Gerhart
@ 2019-07-23 16:06 ` Björn Gerhart
2019-07-23 16:23 ` Guenter Roeck
1 sibling, 1 reply; 12+ messages in thread
From: Björn Gerhart @ 2019-07-23 16:06 UTC (permalink / raw)
To: Guenter Roeck; +Cc: Hardware Monitoring
Thanks for the review Guenter, I checked your proposals. Here comes an update of the patch, and I hope this time the format fits as it should.
Changes:
- simplified differences in register addresses
- although kept NCT6116_REG_TEMP_SOURCE, because otherwise the module
throughs „Invalid temperature source“ messages on loading for each
register not available
- fixed fan enablements
- simplified case statement (fall through)
Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
---
diff -Npaur a/drivers/hwmon/nct6775.c b/drivers/hwmon/nct6775.c
--- a/drivers/hwmon/nct6775.c 2019-07-10 17:08:30.710690605 +0200
+++ b/drivers/hwmon/nct6775.c 2019-07-23 10:17:33.217639944 +0200
@@ -34,6 +34,7 @@
*
* Chip #vin #fan #pwm #temp chip IDs man ID
* nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
+ * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
* nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
* nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
* nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
@@ -72,12 +73,13 @@
#define USE_ALTERNATE
-enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
- nct6795, nct6796, nct6797, nct6798 };
+enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
+ nct6793, nct6795, nct6796, nct6797, nct6798 };
/* used to set data->name = nct6775_device_names[data->sio_kind] */
static const char * const nct6775_device_names[] = {
"nct6106",
+ "nct6116",
"nct6775",
"nct6776",
"nct6779",
@@ -92,6 +94,7 @@ static const char * const nct6775_device
static const char * const nct6775_sio_names[] __initconst = {
"NCT6106D",
+ "NCT6116D",
"NCT6775F",
"NCT6776D/F",
"NCT6779D",
@@ -129,6 +132,7 @@ MODULE_PARM_DESC(fan_debounce, "Enable d
#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
#define SIO_NCT6106_ID 0xc450
+#define SIO_NCT6116_ID 0xd280
#define SIO_NCT6775_ID 0xb470
#define SIO_NCT6776_ID 0xc330
#define SIO_NCT6779_ID 0xc560
@@ -839,10 +843,8 @@ static const u16 NCT6106_FAN_PULSE_SHIFT
static const u8 NCT6106_REG_PWM_MODE[] = { 0xf3, 0xf3, 0xf3 };
static const u8 NCT6106_PWM_MODE_MASK[] = { 0x01, 0x02, 0x04 };
-static const u16 NCT6106_REG_PWM[] = { 0x119, 0x129, 0x139 };
static const u16 NCT6106_REG_PWM_READ[] = { 0x4a, 0x4b, 0x4c };
static const u16 NCT6106_REG_FAN_MODE[] = { 0x113, 0x123, 0x133 };
-static const u16 NCT6106_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130 };
static const u16 NCT6106_REG_TEMP_SOURCE[] = {
0xb0, 0xb1, 0xb2, 0xb3, 0xb4, 0xb5 };
@@ -910,6 +912,70 @@ static const u16 NCT6106_REG_TEMP_CRIT[3
[12] = 0x205,
};
+/* NCT6112D/NCT6114D/NCT6116D specific data */
+
+static const u16 NCT6116_REG_FAN[] = { 0x20, 0x22, 0x24, 0x26, 0x28 };
+static const u16 NCT6116_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4, 0xe6, 0xe8 };
+static const u16 NCT6116_REG_FAN_PULSES[] = { 0xf6, 0xf6, 0xf6, 0xf6, 0xf5 };
+static const u16 NCT6116_FAN_PULSE_SHIFT[] = { 0, 2, 4, 6, 6 };
+
+static const u16 NCT6116_REG_PWM[] = { 0x119, 0x129, 0x139, 0x199, 0x1a9 };
+static const u16 NCT6116_REG_FAN_MODE[] = { 0x113, 0x123, 0x133, 0x193, 0x1a3 };
+static const u16 NCT6116_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130, 0x190, 0x1a0 };
+static const u16 NCT6116_REG_TEMP_SOURCE[] = {
+ 0xb0, 0xb1, 0xb2 };
+
+static const u16 NCT6116_REG_CRITICAL_TEMP[] = {
+ 0x11a, 0x12a, 0x13a, 0x19a, 0x1aa };
+static const u16 NCT6116_REG_CRITICAL_TEMP_TOLERANCE[] = {
+ 0x11b, 0x12b, 0x13b, 0x19b, 0x1ab };
+
+static const u16 NCT6116_REG_CRITICAL_PWM_ENABLE[] = {
+ 0x11c, 0x12c, 0x13c, 0x19c, 0x1ac };
+static const u16 NCT6116_REG_CRITICAL_PWM[] = {
+ 0x11d, 0x12d, 0x13d, 0x19d, 0x1ad };
+
+static const u16 NCT6116_REG_FAN_STEP_UP_TIME[] = {
+ 0x114, 0x124, 0x134, 0x194, 0x1a4 };
+static const u16 NCT6116_REG_FAN_STEP_DOWN_TIME[] = {
+ 0x115, 0x125, 0x135, 0x195, 0x1a5 };
+static const u16 NCT6116_REG_FAN_STOP_OUTPUT[] = {
+ 0x116, 0x126, 0x136, 0x196, 0x1a6 };
+static const u16 NCT6116_REG_FAN_START_OUTPUT[] = {
+ 0x117, 0x127, 0x137, 0x197, 0x1a7 };
+static const u16 NCT6116_REG_FAN_STOP_TIME[] = {
+ 0x118, 0x128, 0x138, 0x198, 0x1a8 };
+static const u16 NCT6116_REG_TOLERANCE_H[] = {
+ 0x112, 0x122, 0x132, 0x192, 0x1a2 };
+
+static const u16 NCT6116_REG_TARGET[] = {
+ 0x111, 0x121, 0x131, 0x191, 0x1a1 };
+
+static const u16 NCT6116_REG_AUTO_TEMP[] = {
+ 0x160, 0x170, 0x180, 0x1d0, 0x1e0 };
+static const u16 NCT6116_REG_AUTO_PWM[] = {
+ 0x164, 0x174, 0x184, 0x1d4, 0x1e4 };
+
+static const s8 NCT6116_ALARM_BITS[] = {
+ 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
+ 9, -1, -1, -1, -1, -1, -1, /* in8..in9 */
+ -1, /* unused */
+ 32, 33, 34, 35, 36, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
+ 48, -1 /* intrusion0, intrusion1 */
+};
+
+static const s8 NCT6116_BEEP_BITS[] = {
+ 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
+ 9, 10, 11, 12, -1, -1, -1, /* in8..in14 */
+ 32, /* global beep enable */
+ 24, 25, 26, 27, 28, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
+ 34, -1 /* intrusion0, intrusion1 */
+};
+
static enum pwm_enable reg_to_pwm_enable(int pwm, int mode)
{
if (mode == 0 && pwm == 255)
@@ -1308,6 +1374,11 @@ static bool is_word_sized(struct nct6775
return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
reg == 0x111 || reg == 0x121 || reg == 0x131;
+ case nct6116:
+ return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
+ reg == 0x26 || reg == 0x28 || reg == 0xe0 || reg == 0xe2 ||
+ reg == 0xe4 || reg == 0xe6 || reg == 0xe8 || reg == 0x111 ||
+ reg == 0x121 || reg == 0x131 || reg == 0x191 || reg == 0x1a1;
case nct6775:
return (((reg & 0xff00) == 0x100 ||
(reg & 0xff00) == 0x200) &&
@@ -1687,6 +1758,7 @@ static void nct6775_update_pwm_limits(st
data->auto_pwm[i][data->auto_pwm_num] = 0xff;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3123,6 +3195,7 @@ store_auto_pwm(struct device *dev, struc
case nct6776:
break; /* always enabled, nothing to do */
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3549,6 +3622,23 @@ nct6775_check_fan_inputs(struct nct6775_
fan3pin = !(cr24 & 0x80);
pwm3pin = cr24 & 0x08;
+ } else if (data->kind == nct6116) {
+ int cr1a = superio_inb(sioreg, 0x1a);
+ int cr1b = superio_inb(sioreg, 0x1b);
+ int cr24 = superio_inb(sioreg, 0x24);
+ int cr2a = superio_inb(sioreg, 0x2a);
+ int cr2b = superio_inb(sioreg, 0x2b);
+ int cr2f = superio_inb(sioreg, 0x2f);
+
+ fan3pin = !(cr2b & 0x10);
+ fan4pin = (cr2b & 0x80) || // pin 1(2)
+ (!(cr2f & 0x10) && (cr1a & 0x04)); // pin 65(66)
+ fan5pin = (cr2b & 0x80) || // pin 126(127)
+ (!(cr1b & 0x03) && (cr2a & 0x02)); // pin 94(96)
+
+ pwm3pin = fan3pin && (cr24 & 0x08);
+ pwm4pin = fan4pin;
+ pwm5pin = fan5pin;
} else {
/*
* NCT6779D, NCT6791D, NCT6792D, NCT6793D, NCT6795D, NCT6796D,
@@ -3779,7 +3869,7 @@ static int nct6775_probe(struct platform
data->REG_FAN_TIME[1] = NCT6106_REG_FAN_STEP_UP_TIME;
data->REG_FAN_TIME[2] = NCT6106_REG_FAN_STEP_DOWN_TIME;
data->REG_TOLERANCE_H = NCT6106_REG_TOLERANCE_H;
- data->REG_PWM[0] = NCT6106_REG_PWM;
+ data->REG_PWM[0] = NCT6116_REG_PWM;
data->REG_PWM[1] = NCT6106_REG_FAN_START_OUTPUT;
data->REG_PWM[2] = NCT6106_REG_FAN_STOP_OUTPUT;
data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
@@ -3798,7 +3888,7 @@ static int nct6775_probe(struct platform
data->REG_CRITICAL_PWM = NCT6106_REG_CRITICAL_PWM;
data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
data->REG_TEMP_SOURCE = NCT6106_REG_TEMP_SOURCE;
- data->REG_TEMP_SEL = NCT6106_REG_TEMP_SEL;
+ data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
@@ -3821,6 +3911,79 @@ static int nct6775_probe(struct platform
reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
break;
+ case nct6116:
+ data->in_num = 9;
+ data->pwm_num = 3;
+ data->auto_pwm_num = 4;
+ data->temp_fixed_num = 3;
+ data->num_temp_alarms = 3;
+ data->num_temp_beeps = 3;
+
+ data->fan_from_reg = fan_from_reg13;
+ data->fan_from_reg_min = fan_from_reg13;
+
+ data->temp_label = nct6776_temp_label;
+ data->temp_mask = NCT6776_TEMP_MASK;
+ data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
+
+ data->REG_VBAT = NCT6106_REG_VBAT;
+ data->REG_DIODE = NCT6106_REG_DIODE;
+ data->DIODE_MASK = NCT6106_DIODE_MASK;
+ data->REG_VIN = NCT6106_REG_IN;
+ data->REG_IN_MINMAX[0] = NCT6106_REG_IN_MIN;
+ data->REG_IN_MINMAX[1] = NCT6106_REG_IN_MAX;
+ data->REG_TARGET = NCT6116_REG_TARGET;
+ data->REG_FAN = NCT6116_REG_FAN;
+ data->REG_FAN_MODE = NCT6116_REG_FAN_MODE;
+ data->REG_FAN_MIN = NCT6116_REG_FAN_MIN;
+ data->REG_FAN_PULSES = NCT6116_REG_FAN_PULSES;
+ data->FAN_PULSE_SHIFT = NCT6116_FAN_PULSE_SHIFT;
+ data->REG_FAN_TIME[0] = NCT6116_REG_FAN_STOP_TIME;
+ data->REG_FAN_TIME[1] = NCT6116_REG_FAN_STEP_UP_TIME;
+ data->REG_FAN_TIME[2] = NCT6116_REG_FAN_STEP_DOWN_TIME;
+ data->REG_TOLERANCE_H = NCT6116_REG_TOLERANCE_H;
+ data->REG_PWM[0] = NCT6116_REG_PWM;
+ data->REG_PWM[1] = NCT6116_REG_FAN_START_OUTPUT;
+ data->REG_PWM[2] = NCT6116_REG_FAN_STOP_OUTPUT;
+ data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
+ data->REG_PWM[6] = NCT6106_REG_WEIGHT_DUTY_BASE;
+ data->REG_PWM_READ = NCT6106_REG_PWM_READ;
+ data->REG_PWM_MODE = NCT6106_REG_PWM_MODE;
+ data->PWM_MODE_MASK = NCT6106_PWM_MODE_MASK;
+ data->REG_AUTO_TEMP = NCT6116_REG_AUTO_TEMP;
+ data->REG_AUTO_PWM = NCT6116_REG_AUTO_PWM;
+ data->REG_CRITICAL_TEMP = NCT6116_REG_CRITICAL_TEMP;
+ data->REG_CRITICAL_TEMP_TOLERANCE
+ = NCT6116_REG_CRITICAL_TEMP_TOLERANCE;
+ data->REG_CRITICAL_PWM_ENABLE = NCT6116_REG_CRITICAL_PWM_ENABLE;
+ data->CRITICAL_PWM_ENABLE_MASK
+ = NCT6106_CRITICAL_PWM_ENABLE_MASK;
+ data->REG_CRITICAL_PWM = NCT6116_REG_CRITICAL_PWM;
+ data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
+ data->REG_TEMP_SOURCE = NCT6116_REG_TEMP_SOURCE;
+ data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
+ data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
+ data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
+ data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
+ data->REG_WEIGHT_TEMP[2] = NCT6106_REG_WEIGHT_TEMP_BASE;
+ data->REG_ALARM = NCT6106_REG_ALARM;
+ data->ALARM_BITS = NCT6116_ALARM_BITS;
+ data->REG_BEEP = NCT6106_REG_BEEP;
+ data->BEEP_BITS = NCT6116_BEEP_BITS;
+
+ reg_temp = NCT6106_REG_TEMP;
+ reg_temp_mon = NCT6106_REG_TEMP_MON;
+ num_reg_temp = ARRAY_SIZE(NCT6106_REG_TEMP);
+ num_reg_temp_mon = ARRAY_SIZE(NCT6106_REG_TEMP_MON);
+ reg_temp_over = NCT6106_REG_TEMP_OVER;
+ reg_temp_hyst = NCT6106_REG_TEMP_HYST;
+ reg_temp_config = NCT6106_REG_TEMP_CONFIG;
+ reg_temp_alternate = NCT6106_REG_TEMP_ALTERNATE;
+ reg_temp_crit = NCT6106_REG_TEMP_CRIT;
+ reg_temp_crit_l = NCT6106_REG_TEMP_CRIT_L;
+ reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
+
+ break;
case nct6775:
data->in_num = 9;
data->pwm_num = 3;
@@ -4366,6 +4529,7 @@ static int nct6775_probe(struct platform
data->have_vid = (cr2a & 0x60) == 0x40;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -4395,6 +4559,7 @@ static int nct6775_probe(struct platform
NCT6775_REG_CR_FAN_DEBOUNCE);
switch (data->kind) {
case nct6106:
+ case nct6116:
tmp |= 0xe0;
break;
case nct6775:
@@ -4590,6 +4755,9 @@ static int __init nct6775_find(int sioad
case SIO_NCT6106_ID:
sio_data->kind = nct6106;
break;
+ case SIO_NCT6116_ID:
+ sio_data->kind = nct6116;
+ break;
case SIO_NCT6775_ID:
sio_data->kind = nct6775;
break;
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-22 17:46 ` Björn Gerhart
@ 2019-07-22 20:12 ` Guenter Roeck
0 siblings, 0 replies; 12+ messages in thread
From: Guenter Roeck @ 2019-07-22 20:12 UTC (permalink / raw)
To: Björn Gerhart; +Cc: Hardware Monitoring
On Mon, Jul 22, 2019 at 07:46:58PM +0200, Björn Gerhart wrote:
> Thanks for the review Guenter, I checked your proposals, and here I comes an
> update of the patch.
>
> Changes:
> - simplified differences in register addresses
> - fixed fan enablements
> - simplified case statement
>
> Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
Formatting is all messed up :-(. Can you have a look ?
Thanks,
Guenter
> ---
> diff -Naur a/drivers/hwmon/nct6775.c b/drivers/hwmon/nct6775.c
> --- a/drivers/hwmon/nct6775.c 2019-07-10 17:08:30.710690605 +0200
> +++ b/drivers/hwmon/nct6775.c 2019-07-22 16:02:17.363091327 +0200
> @@ -34,6 +34,7 @@
> *
> * Chip #vin #fan #pwm #temp chip IDs man ID
> * nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
> + * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
> * nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
> * nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
> * nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
> @@ -72,12 +73,13 @@
>
> #define USE_ALTERNATE
>
> -enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
> - nct6795, nct6796, nct6797, nct6798 };
> +enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
> + nct6793, nct6795, nct6796, nct6797, nct6798 };
>
> /* used to set data->name = nct6775_device_names[data->sio_kind] */
> static const char * const nct6775_device_names[] = {
> "nct6106",
> + "nct6116",
> "nct6775",
> "nct6776",
> "nct6779",
> @@ -92,6 +94,7 @@
>
> static const char * const nct6775_sio_names[] __initconst = {
> "NCT6106D",
> + "NCT6116D",
> "NCT6775F",
> "NCT6776D/F",
> "NCT6779D",
> @@ -129,6 +132,7 @@
> #define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
>
> #define SIO_NCT6106_ID 0xc450
> +#define SIO_NCT6116_ID 0xd280
> #define SIO_NCT6775_ID 0xb470
> #define SIO_NCT6776_ID 0xc330
> #define SIO_NCT6779_ID 0xc560
> @@ -839,10 +843,8 @@
>
> static const u8 NCT6106_REG_PWM_MODE[] = { 0xf3, 0xf3, 0xf3 };
> static const u8 NCT6106_PWM_MODE_MASK[] = { 0x01, 0x02, 0x04 };
> -static const u16 NCT6106_REG_PWM[] = { 0x119, 0x129, 0x139 };
> static const u16 NCT6106_REG_PWM_READ[] = { 0x4a, 0x4b, 0x4c };
> static const u16 NCT6106_REG_FAN_MODE[] = { 0x113, 0x123, 0x133 };
> -static const u16 NCT6106_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130 };
> static const u16 NCT6106_REG_TEMP_SOURCE[] = {
> 0xb0, 0xb1, 0xb2, 0xb3, 0xb4, 0xb5 };
>
> @@ -910,6 +912,68 @@
> [12] = 0x205,
> };
>
> +/* NCT6112D/NCT6114D/NCT6116D specific data */
> +
> +static const u16 NCT6116_REG_FAN[] = { 0x20, 0x22, 0x24, 0x26, 0x28 };
> +static const u16 NCT6116_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4, 0xe6, 0xe8 };
> +static const u16 NCT6116_REG_FAN_PULSES[] = { 0xf6, 0xf6, 0xf6, 0xf6, 0xf5
> };
> +static const u16 NCT6116_FAN_PULSE_SHIFT[] = { 0, 2, 4, 6, 6 };
> +
> +static const u16 NCT6116_REG_PWM[] = { 0x119, 0x129, 0x139, 0x199, 0x1a9 };
> +static const u16 NCT6116_REG_FAN_MODE[] = { 0x113, 0x123, 0x133, 0x193,
> 0x1a3 };
> +static const u16 NCT6116_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130, 0x190,
> 0x1a0 };
> +
> +static const u16 NCT6116_REG_CRITICAL_TEMP[] = {
> + 0x11a, 0x12a, 0x13a, 0x19a, 0x1aa };
> +static const u16 NCT6116_REG_CRITICAL_TEMP_TOLERANCE[] = {
> + 0x11b, 0x12b, 0x13b, 0x19b, 0x1ab };
> +
> +static const u16 NCT6116_REG_CRITICAL_PWM_ENABLE[] = {
> + 0x11c, 0x12c, 0x13c, 0x19c, 0x1ac };
> +static const u16 NCT6116_REG_CRITICAL_PWM[] = {
> + 0x11d, 0x12d, 0x13d, 0x19d, 0x1ad };
> +
> +static const u16 NCT6116_REG_FAN_STEP_UP_TIME[] = {
> + 0x114, 0x124, 0x134, 0x194, 0x1a4 };
> +static const u16 NCT6116_REG_FAN_STEP_DOWN_TIME[] = {
> + 0x115, 0x125, 0x135, 0x195, 0x1a5 };
> +static const u16 NCT6116_REG_FAN_STOP_OUTPUT[] = {
> + 0x116, 0x126, 0x136, 0x196, 0x1a6 };
> +static const u16 NCT6116_REG_FAN_START_OUTPUT[] = {
> + 0x117, 0x127, 0x137, 0x197, 0x1a7 };
> +static const u16 NCT6116_REG_FAN_STOP_TIME[] = {
> + 0x118, 0x128, 0x138, 0x198, 0x1a8 };
> +static const u16 NCT6116_REG_TOLERANCE_H[] = {
> + 0x112, 0x122, 0x132, 0x192, 0x1a2 };
> +
> +static const u16 NCT6116_REG_TARGET[] = {
> + 0x111, 0x121, 0x131, 0x191, 0x1a1 };
> +
> +static const u16 NCT6116_REG_AUTO_TEMP[] = {
> + 0x160, 0x170, 0x180, 0x1d0, 0x1e0 };
> +static const u16 NCT6116_REG_AUTO_PWM[] = {
> + 0x164, 0x174, 0x184, 0x1d4, 0x1e4 };
> +
> +static const s8 NCT6116_ALARM_BITS[] = {
> + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
> + 9, -1, -1, -1, -1, -1, -1, /* in8..in9 */
> + -1, /* unused */
> + 32, 33, 34, 35, 36, /* fan1..fan5 */
> + -1, -1, -1, /* unused */
> + 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
> + 48, -1 /* intrusion0, intrusion1 */
> +};
> +
> +static const s8 NCT6116_BEEP_BITS[] = {
> + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
> + 9, 10, 11, 12, -1, -1, -1, /* in8..in14 */
> + 32, /* global beep enable */
> + 24, 25, 26, 27, 28, /* fan1..fan5 */
> + -1, -1, -1, /* unused */
> + 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
> + 34, -1 /* intrusion0, intrusion1 */
> +};
> +
> static enum pwm_enable reg_to_pwm_enable(int pwm, int mode)
> {
> if (mode == 0 && pwm == 255)
> @@ -1308,6 +1372,11 @@
> return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
> reg == 0x111 || reg == 0x121 || reg == 0x131;
> + case nct6116:
> + return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> + reg == 0x26 || reg == 0x28 || reg == 0xe0 || reg == 0xe2 ||
> + reg == 0xe4 || reg == 0xe6 || reg == 0xe8 || reg == 0x111 ||
> + reg == 0x121 || reg == 0x131 || reg == 0x191 || reg == 0x1a1;
> case nct6775:
> return (((reg & 0xff00) == 0x100 ||
> (reg & 0xff00) == 0x200) &&
> @@ -1687,6 +1756,7 @@
> data->auto_pwm[i][data->auto_pwm_num] = 0xff;
> break;
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -3123,6 +3193,7 @@
> case nct6776:
> break; /* always enabled, nothing to do */
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -3549,6 +3620,23 @@
>
> fan3pin = !(cr24 & 0x80);
> pwm3pin = cr24 & 0x08;
> + } else if (data->kind == nct6116) {
> + int cr1a = superio_inb(sioreg, 0x1a);
> + int cr1b = superio_inb(sioreg, 0x1b);
> + int cr24 = superio_inb(sioreg, 0x24);
> + int cr2a = superio_inb(sioreg, 0x2a);
> + int cr2b = superio_inb(sioreg, 0x2b);
> + int cr2f = superio_inb(sioreg, 0x2f);
> +
> + fan3pin = !(cr2b & 0x10);
> + fan4pin = (cr2b & 0x80) || // pin 1(2)
> + (!(cr2f & 0x10) && (cr1a & 0x04)); // pin 65(66)
> + fan5pin = (cr2b & 0x80) || // pin 126(127)
> + (!(cr1b & 0x03) && (cr2a & 0x02)); // pin 94(96)
> +
> + pwm3pin = fan3pin && (cr24 & 0x08);
> + pwm4pin = fan4pin;
> + pwm5pin = fan5pin;
> } else {
> /*
> * NCT6779D, NCT6791D, NCT6792D, NCT6793D, NCT6795D, NCT6796D,
> @@ -3779,7 +3867,7 @@
> data->REG_FAN_TIME[1] = NCT6106_REG_FAN_STEP_UP_TIME;
> data->REG_FAN_TIME[2] = NCT6106_REG_FAN_STEP_DOWN_TIME;
> data->REG_TOLERANCE_H = NCT6106_REG_TOLERANCE_H;
> - data->REG_PWM[0] = NCT6106_REG_PWM;
> + data->REG_PWM[0] = NCT6116_REG_PWM;
> data->REG_PWM[1] = NCT6106_REG_FAN_START_OUTPUT;
> data->REG_PWM[2] = NCT6106_REG_FAN_STOP_OUTPUT;
> data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
> @@ -3798,7 +3886,7 @@
> data->REG_CRITICAL_PWM = NCT6106_REG_CRITICAL_PWM;
> data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
> data->REG_TEMP_SOURCE = NCT6106_REG_TEMP_SOURCE;
> - data->REG_TEMP_SEL = NCT6106_REG_TEMP_SEL;
> + data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
> data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
> data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
> data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
> @@ -3821,6 +3909,79 @@
> reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
>
> break;
> + case nct6116:
> + data->in_num = 9;
> + data->pwm_num = 3;
> + data->auto_pwm_num = 4;
> + data->temp_fixed_num = 3;
> + data->num_temp_alarms = 3;
> + data->num_temp_beeps = 3;
> +
> + data->fan_from_reg = fan_from_reg13;
> + data->fan_from_reg_min = fan_from_reg13;
> +
> + data->temp_label = nct6776_temp_label;
> + data->temp_mask = NCT6776_TEMP_MASK;
> + data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
> +
> + data->REG_VBAT = NCT6106_REG_VBAT;
> + data->REG_DIODE = NCT6106_REG_DIODE;
> + data->DIODE_MASK = NCT6106_DIODE_MASK;
> + data->REG_VIN = NCT6106_REG_IN;
> + data->REG_IN_MINMAX[0] = NCT6106_REG_IN_MIN;
> + data->REG_IN_MINMAX[1] = NCT6106_REG_IN_MAX;
> + data->REG_TARGET = NCT6116_REG_TARGET;
> + data->REG_FAN = NCT6116_REG_FAN;
> + data->REG_FAN_MODE = NCT6116_REG_FAN_MODE;
> + data->REG_FAN_MIN = NCT6116_REG_FAN_MIN;
> + data->REG_FAN_PULSES = NCT6116_REG_FAN_PULSES;
> + data->FAN_PULSE_SHIFT = NCT6116_FAN_PULSE_SHIFT;
> + data->REG_FAN_TIME[0] = NCT6116_REG_FAN_STOP_TIME;
> + data->REG_FAN_TIME[1] = NCT6116_REG_FAN_STEP_UP_TIME;
> + data->REG_FAN_TIME[2] = NCT6116_REG_FAN_STEP_DOWN_TIME;
> + data->REG_TOLERANCE_H = NCT6116_REG_TOLERANCE_H;
> + data->REG_PWM[0] = NCT6116_REG_PWM;
> + data->REG_PWM[1] = NCT6116_REG_FAN_START_OUTPUT;
> + data->REG_PWM[2] = NCT6116_REG_FAN_STOP_OUTPUT;
> + data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
> + data->REG_PWM[6] = NCT6106_REG_WEIGHT_DUTY_BASE;
> + data->REG_PWM_READ = NCT6106_REG_PWM_READ;
> + data->REG_PWM_MODE = NCT6106_REG_PWM_MODE;
> + data->PWM_MODE_MASK = NCT6106_PWM_MODE_MASK;
> + data->REG_AUTO_TEMP = NCT6116_REG_AUTO_TEMP;
> + data->REG_AUTO_PWM = NCT6116_REG_AUTO_PWM;
> + data->REG_CRITICAL_TEMP = NCT6116_REG_CRITICAL_TEMP;
> + data->REG_CRITICAL_TEMP_TOLERANCE
> + = NCT6116_REG_CRITICAL_TEMP_TOLERANCE;
> + data->REG_CRITICAL_PWM_ENABLE = NCT6116_REG_CRITICAL_PWM_ENABLE;
> + data->CRITICAL_PWM_ENABLE_MASK
> + = NCT6106_CRITICAL_PWM_ENABLE_MASK;
> + data->REG_CRITICAL_PWM = NCT6116_REG_CRITICAL_PWM;
> + data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
> + data->REG_TEMP_SOURCE = NCT6106_REG_TEMP_SOURCE;
> + data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
> + data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
> + data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
> + data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
> + data->REG_WEIGHT_TEMP[2] = NCT6106_REG_WEIGHT_TEMP_BASE;
> + data->REG_ALARM = NCT6106_REG_ALARM;
> + data->ALARM_BITS = NCT6116_ALARM_BITS;
> + data->REG_BEEP = NCT6106_REG_BEEP;
> + data->BEEP_BITS = NCT6116_BEEP_BITS;
> +
> + reg_temp = NCT6106_REG_TEMP;
> + reg_temp_mon = NCT6106_REG_TEMP_MON;
> + num_reg_temp = ARRAY_SIZE(NCT6106_REG_TEMP);
> + num_reg_temp_mon = ARRAY_SIZE(NCT6106_REG_TEMP_MON);
> + reg_temp_over = NCT6106_REG_TEMP_OVER;
> + reg_temp_hyst = NCT6106_REG_TEMP_HYST;
> + reg_temp_config = NCT6106_REG_TEMP_CONFIG;
> + reg_temp_alternate = NCT6106_REG_TEMP_ALTERNATE;
> + reg_temp_crit = NCT6106_REG_TEMP_CRIT;
> + reg_temp_crit_l = NCT6106_REG_TEMP_CRIT_L;
> + reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
> +
> + break;
> case nct6775:
> data->in_num = 9;
> data->pwm_num = 3;
> @@ -4366,6 +4527,7 @@
> data->have_vid = (cr2a & 0x60) == 0x40;
> break;
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -4395,6 +4557,7 @@
> NCT6775_REG_CR_FAN_DEBOUNCE);
> switch (data->kind) {
> case nct6106:
> + case nct6116:
> tmp |= 0xe0;
> break;
> case nct6775:
> @@ -4590,6 +4753,9 @@
> case SIO_NCT6106_ID:
> sio_data->kind = nct6106;
> break;
> + case SIO_NCT6116_ID:
> + sio_data->kind = nct6116;
> + break;
> case SIO_NCT6775_ID:
> sio_data->kind = nct6775;
> break;
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-19 19:37 ` Guenter Roeck
@ 2019-07-22 17:46 ` Björn Gerhart
2019-07-22 20:12 ` Guenter Roeck
2019-07-23 16:06 ` Björn Gerhart
1 sibling, 1 reply; 12+ messages in thread
From: Björn Gerhart @ 2019-07-22 17:46 UTC (permalink / raw)
To: Guenter Roeck; +Cc: Hardware Monitoring
Thanks for the review Guenter, I checked your proposals, and here I
comes an update of the patch.
Changes:
- simplified differences in register addresses
- fixed fan enablements
- simplified case statement
Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
---
diff -Naur a/drivers/hwmon/nct6775.c b/drivers/hwmon/nct6775.c
--- a/drivers/hwmon/nct6775.c 2019-07-10 17:08:30.710690605 +0200
+++ b/drivers/hwmon/nct6775.c 2019-07-22 16:02:17.363091327 +0200
@@ -34,6 +34,7 @@
*
* Chip #vin #fan #pwm #temp chip IDs man ID
* nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
+ * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
* nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
* nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
* nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
@@ -72,12 +73,13 @@
#define USE_ALTERNATE
-enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792,
nct6793,
- nct6795, nct6796, nct6797, nct6798 };
+enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791,
nct6792,
+ nct6793, nct6795, nct6796, nct6797, nct6798 };
/* used to set data->name = nct6775_device_names[data->sio_kind] */
static const char * const nct6775_device_names[] = {
"nct6106",
+ "nct6116",
"nct6775",
"nct6776",
"nct6779",
@@ -92,6 +94,7 @@
static const char * const nct6775_sio_names[] __initconst = {
"NCT6106D",
+ "NCT6116D",
"NCT6775F",
"NCT6776D/F",
"NCT6779D",
@@ -129,6 +132,7 @@
#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
#define SIO_NCT6106_ID 0xc450
+#define SIO_NCT6116_ID 0xd280
#define SIO_NCT6775_ID 0xb470
#define SIO_NCT6776_ID 0xc330
#define SIO_NCT6779_ID 0xc560
@@ -839,10 +843,8 @@
static const u8 NCT6106_REG_PWM_MODE[] = { 0xf3, 0xf3, 0xf3 };
static const u8 NCT6106_PWM_MODE_MASK[] = { 0x01, 0x02, 0x04 };
-static const u16 NCT6106_REG_PWM[] = { 0x119, 0x129, 0x139 };
static const u16 NCT6106_REG_PWM_READ[] = { 0x4a, 0x4b, 0x4c };
static const u16 NCT6106_REG_FAN_MODE[] = { 0x113, 0x123, 0x133 };
-static const u16 NCT6106_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130 };
static const u16 NCT6106_REG_TEMP_SOURCE[] = {
0xb0, 0xb1, 0xb2, 0xb3, 0xb4, 0xb5 };
@@ -910,6 +912,68 @@
[12] = 0x205,
};
+/* NCT6112D/NCT6114D/NCT6116D specific data */
+
+static const u16 NCT6116_REG_FAN[] = { 0x20, 0x22, 0x24, 0x26, 0x28 };
+static const u16 NCT6116_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4, 0xe6, 0xe8
};
+static const u16 NCT6116_REG_FAN_PULSES[] = { 0xf6, 0xf6, 0xf6, 0xf6,
0xf5 };
+static const u16 NCT6116_FAN_PULSE_SHIFT[] = { 0, 2, 4, 6, 6 };
+
+static const u16 NCT6116_REG_PWM[] = { 0x119, 0x129, 0x139, 0x199,
0x1a9 };
+static const u16 NCT6116_REG_FAN_MODE[] = { 0x113, 0x123, 0x133, 0x193,
0x1a3 };
+static const u16 NCT6116_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130, 0x190,
0x1a0 };
+
+static const u16 NCT6116_REG_CRITICAL_TEMP[] = {
+ 0x11a, 0x12a, 0x13a, 0x19a, 0x1aa };
+static const u16 NCT6116_REG_CRITICAL_TEMP_TOLERANCE[] = {
+ 0x11b, 0x12b, 0x13b, 0x19b, 0x1ab };
+
+static const u16 NCT6116_REG_CRITICAL_PWM_ENABLE[] = {
+ 0x11c, 0x12c, 0x13c, 0x19c, 0x1ac };
+static const u16 NCT6116_REG_CRITICAL_PWM[] = {
+ 0x11d, 0x12d, 0x13d, 0x19d, 0x1ad };
+
+static const u16 NCT6116_REG_FAN_STEP_UP_TIME[] = {
+ 0x114, 0x124, 0x134, 0x194, 0x1a4 };
+static const u16 NCT6116_REG_FAN_STEP_DOWN_TIME[] = {
+ 0x115, 0x125, 0x135, 0x195, 0x1a5 };
+static const u16 NCT6116_REG_FAN_STOP_OUTPUT[] = {
+ 0x116, 0x126, 0x136, 0x196, 0x1a6 };
+static const u16 NCT6116_REG_FAN_START_OUTPUT[] = {
+ 0x117, 0x127, 0x137, 0x197, 0x1a7 };
+static const u16 NCT6116_REG_FAN_STOP_TIME[] = {
+ 0x118, 0x128, 0x138, 0x198, 0x1a8 };
+static const u16 NCT6116_REG_TOLERANCE_H[] = {
+ 0x112, 0x122, 0x132, 0x192, 0x1a2 };
+
+static const u16 NCT6116_REG_TARGET[] = {
+ 0x111, 0x121, 0x131, 0x191, 0x1a1 };
+
+static const u16 NCT6116_REG_AUTO_TEMP[] = {
+ 0x160, 0x170, 0x180, 0x1d0, 0x1e0 };
+static const u16 NCT6116_REG_AUTO_PWM[] = {
+ 0x164, 0x174, 0x184, 0x1d4, 0x1e4 };
+
+static const s8 NCT6116_ALARM_BITS[] = {
+ 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
+ 9, -1, -1, -1, -1, -1, -1, /* in8..in9 */
+ -1, /* unused */
+ 32, 33, 34, 35, 36, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
+ 48, -1 /* intrusion0, intrusion1 */
+};
+
+static const s8 NCT6116_BEEP_BITS[] = {
+ 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
+ 9, 10, 11, 12, -1, -1, -1, /* in8..in14 */
+ 32, /* global beep enable */
+ 24, 25, 26, 27, 28, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
+ 34, -1 /* intrusion0, intrusion1 */
+};
+
static enum pwm_enable reg_to_pwm_enable(int pwm, int mode)
{
if (mode == 0 && pwm == 255)
@@ -1308,6 +1372,11 @@
return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
reg == 0x111 || reg == 0x121 || reg == 0x131;
+ case nct6116:
+ return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
+ reg == 0x26 || reg == 0x28 || reg == 0xe0 || reg == 0xe2 ||
+ reg == 0xe4 || reg == 0xe6 || reg == 0xe8 || reg == 0x111 ||
+ reg == 0x121 || reg == 0x131 || reg == 0x191 || reg == 0x1a1;
case nct6775:
return (((reg & 0xff00) == 0x100 ||
(reg & 0xff00) == 0x200) &&
@@ -1687,6 +1756,7 @@
data->auto_pwm[i][data->auto_pwm_num] = 0xff;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3123,6 +3193,7 @@
case nct6776:
break; /* always enabled, nothing to do */
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3549,6 +3620,23 @@
fan3pin = !(cr24 & 0x80);
pwm3pin = cr24 & 0x08;
+ } else if (data->kind == nct6116) {
+ int cr1a = superio_inb(sioreg, 0x1a);
+ int cr1b = superio_inb(sioreg, 0x1b);
+ int cr24 = superio_inb(sioreg, 0x24);
+ int cr2a = superio_inb(sioreg, 0x2a);
+ int cr2b = superio_inb(sioreg, 0x2b);
+ int cr2f = superio_inb(sioreg, 0x2f);
+
+ fan3pin = !(cr2b & 0x10);
+ fan4pin = (cr2b & 0x80) || // pin 1(2)
+ (!(cr2f & 0x10) && (cr1a & 0x04)); // pin 65(66)
+ fan5pin = (cr2b & 0x80) || // pin 126(127)
+ (!(cr1b & 0x03) && (cr2a & 0x02)); // pin 94(96)
+
+ pwm3pin = fan3pin && (cr24 & 0x08);
+ pwm4pin = fan4pin;
+ pwm5pin = fan5pin;
} else {
/*
* NCT6779D, NCT6791D, NCT6792D, NCT6793D, NCT6795D, NCT6796D,
@@ -3779,7 +3867,7 @@
data->REG_FAN_TIME[1] = NCT6106_REG_FAN_STEP_UP_TIME;
data->REG_FAN_TIME[2] = NCT6106_REG_FAN_STEP_DOWN_TIME;
data->REG_TOLERANCE_H = NCT6106_REG_TOLERANCE_H;
- data->REG_PWM[0] = NCT6106_REG_PWM;
+ data->REG_PWM[0] = NCT6116_REG_PWM;
data->REG_PWM[1] = NCT6106_REG_FAN_START_OUTPUT;
data->REG_PWM[2] = NCT6106_REG_FAN_STOP_OUTPUT;
data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
@@ -3798,7 +3886,7 @@
data->REG_CRITICAL_PWM = NCT6106_REG_CRITICAL_PWM;
data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
data->REG_TEMP_SOURCE = NCT6106_REG_TEMP_SOURCE;
- data->REG_TEMP_SEL = NCT6106_REG_TEMP_SEL;
+ data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
@@ -3821,6 +3909,79 @@
reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
break;
+ case nct6116:
+ data->in_num = 9;
+ data->pwm_num = 3;
+ data->auto_pwm_num = 4;
+ data->temp_fixed_num = 3;
+ data->num_temp_alarms = 3;
+ data->num_temp_beeps = 3;
+
+ data->fan_from_reg = fan_from_reg13;
+ data->fan_from_reg_min = fan_from_reg13;
+
+ data->temp_label = nct6776_temp_label;
+ data->temp_mask = NCT6776_TEMP_MASK;
+ data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
+
+ data->REG_VBAT = NCT6106_REG_VBAT;
+ data->REG_DIODE = NCT6106_REG_DIODE;
+ data->DIODE_MASK = NCT6106_DIODE_MASK;
+ data->REG_VIN = NCT6106_REG_IN;
+ data->REG_IN_MINMAX[0] = NCT6106_REG_IN_MIN;
+ data->REG_IN_MINMAX[1] = NCT6106_REG_IN_MAX;
+ data->REG_TARGET = NCT6116_REG_TARGET;
+ data->REG_FAN = NCT6116_REG_FAN;
+ data->REG_FAN_MODE = NCT6116_REG_FAN_MODE;
+ data->REG_FAN_MIN = NCT6116_REG_FAN_MIN;
+ data->REG_FAN_PULSES = NCT6116_REG_FAN_PULSES;
+ data->FAN_PULSE_SHIFT = NCT6116_FAN_PULSE_SHIFT;
+ data->REG_FAN_TIME[0] = NCT6116_REG_FAN_STOP_TIME;
+ data->REG_FAN_TIME[1] = NCT6116_REG_FAN_STEP_UP_TIME;
+ data->REG_FAN_TIME[2] = NCT6116_REG_FAN_STEP_DOWN_TIME;
+ data->REG_TOLERANCE_H = NCT6116_REG_TOLERANCE_H;
+ data->REG_PWM[0] = NCT6116_REG_PWM;
+ data->REG_PWM[1] = NCT6116_REG_FAN_START_OUTPUT;
+ data->REG_PWM[2] = NCT6116_REG_FAN_STOP_OUTPUT;
+ data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
+ data->REG_PWM[6] = NCT6106_REG_WEIGHT_DUTY_BASE;
+ data->REG_PWM_READ = NCT6106_REG_PWM_READ;
+ data->REG_PWM_MODE = NCT6106_REG_PWM_MODE;
+ data->PWM_MODE_MASK = NCT6106_PWM_MODE_MASK;
+ data->REG_AUTO_TEMP = NCT6116_REG_AUTO_TEMP;
+ data->REG_AUTO_PWM = NCT6116_REG_AUTO_PWM;
+ data->REG_CRITICAL_TEMP = NCT6116_REG_CRITICAL_TEMP;
+ data->REG_CRITICAL_TEMP_TOLERANCE
+ = NCT6116_REG_CRITICAL_TEMP_TOLERANCE;
+ data->REG_CRITICAL_PWM_ENABLE = NCT6116_REG_CRITICAL_PWM_ENABLE;
+ data->CRITICAL_PWM_ENABLE_MASK
+ = NCT6106_CRITICAL_PWM_ENABLE_MASK;
+ data->REG_CRITICAL_PWM = NCT6116_REG_CRITICAL_PWM;
+ data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
+ data->REG_TEMP_SOURCE = NCT6106_REG_TEMP_SOURCE;
+ data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
+ data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
+ data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
+ data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
+ data->REG_WEIGHT_TEMP[2] = NCT6106_REG_WEIGHT_TEMP_BASE;
+ data->REG_ALARM = NCT6106_REG_ALARM;
+ data->ALARM_BITS = NCT6116_ALARM_BITS;
+ data->REG_BEEP = NCT6106_REG_BEEP;
+ data->BEEP_BITS = NCT6116_BEEP_BITS;
+
+ reg_temp = NCT6106_REG_TEMP;
+ reg_temp_mon = NCT6106_REG_TEMP_MON;
+ num_reg_temp = ARRAY_SIZE(NCT6106_REG_TEMP);
+ num_reg_temp_mon = ARRAY_SIZE(NCT6106_REG_TEMP_MON);
+ reg_temp_over = NCT6106_REG_TEMP_OVER;
+ reg_temp_hyst = NCT6106_REG_TEMP_HYST;
+ reg_temp_config = NCT6106_REG_TEMP_CONFIG;
+ reg_temp_alternate = NCT6106_REG_TEMP_ALTERNATE;
+ reg_temp_crit = NCT6106_REG_TEMP_CRIT;
+ reg_temp_crit_l = NCT6106_REG_TEMP_CRIT_L;
+ reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
+
+ break;
case nct6775:
data->in_num = 9;
data->pwm_num = 3;
@@ -4366,6 +4527,7 @@
data->have_vid = (cr2a & 0x60) == 0x40;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -4395,6 +4557,7 @@
NCT6775_REG_CR_FAN_DEBOUNCE);
switch (data->kind) {
case nct6106:
+ case nct6116:
tmp |= 0xe0;
break;
case nct6775:
@@ -4590,6 +4753,9 @@
case SIO_NCT6106_ID:
sio_data->kind = nct6106;
break;
+ case SIO_NCT6116_ID:
+ sio_data->kind = nct6116;
+ break;
case SIO_NCT6775_ID:
sio_data->kind = nct6775;
break;
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-19 18:01 ` Björn Gerhart
@ 2019-07-19 19:37 ` Guenter Roeck
2019-07-22 17:46 ` Björn Gerhart
2019-07-23 16:06 ` Björn Gerhart
0 siblings, 2 replies; 12+ messages in thread
From: Guenter Roeck @ 2019-07-19 19:37 UTC (permalink / raw)
To: Björn Gerhart; +Cc: Hardware Monitoring
On Fri, Jul 19, 2019 at 08:01:21PM +0200, Björn Gerhart wrote:
> Hi Guenter,
>
> I reworked the code after studying the details of the spec.
>
> Changes:
> - patch created against the tree of the kernel sources base dir
> - only define the different registers in contrast to nct6106
> - fixed details of the fan configuration
>
Getting closer ... some more comments below.
Thanks,
Guenter
> Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
> ---
> diff -Naur a/drivers/hwmon/nct6775.c b/drivers/hwmon/nct6775.c
> --- a/drivers/hwmon/nct6775.c 2019-07-19 15:29:34.960278982 +0200
> +++ b/drivers/hwmon/nct6775.c 2019-07-19 15:29:47.332805721 +0200
> @@ -34,6 +34,7 @@
> *
> * Chip #vin #fan #pwm #temp chip IDs man ID
> * nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
> + * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
> * nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
> * nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
> * nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
> @@ -72,12 +73,13 @@
>
> #define USE_ALTERNATE
>
> -enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
> - nct6795, nct6796, nct6797, nct6798 };
> +enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
> + nct6793, nct6795, nct6796, nct6797, nct6798 };
>
> /* used to set data->name = nct6775_device_names[data->sio_kind] */
> static const char * const nct6775_device_names[] = {
> "nct6106",
> + "nct6116",
> "nct6775",
> "nct6776",
> "nct6779",
> @@ -92,6 +94,7 @@
>
> static const char * const nct6775_sio_names[] __initconst = {
> "NCT6106D",
> + "NCT6116D",
> "NCT6775F",
> "NCT6776D/F",
> "NCT6779D",
> @@ -129,6 +132,7 @@
> #define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
>
> #define SIO_NCT6106_ID 0xc450
> +#define SIO_NCT6116_ID 0xd280
> #define SIO_NCT6775_ID 0xb470
> #define SIO_NCT6776_ID 0xc330
> #define SIO_NCT6779_ID 0xc560
> @@ -910,6 +914,78 @@
> [12] = 0x205,
> };
>
> +/* NCT6112D/NCT6114D/NCT6116D specific data */
> +
> +static const u16 NCT6116_REG_TEMP[] = { 0x10, 0x11, 0x12 };
Unnecessary: The first three registers in NCT6106_REG_TEMP
match.
> +static const u16 NCT6116_REG_TEMP_HYST[] = { 0xc3, 0xc7, 0xcb };
> +static const u16 NCT6116_REG_TEMP_OVER[] = { 0xc2, 0xc6, 0xca };
> +static const u16 NCT6116_REG_TEMP_CRIT_L[] = { 0xc0, 0xc4, 0xc8 };
> +static const u16 NCT6116_REG_TEMP_CRIT_H[] = { 0xc1, 0xc5, 0xc9 };
> +static const u16 NCT6116_REG_TEMP_CONFIG[] = { 0xb7, 0xb8, 0xb9 };
Same for all of the above.
> +
> +static const u16 NCT6116_REG_FAN[] = { 0x20, 0x22, 0x24, 0x26, 0x28 };
> +static const u16 NCT6116_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4, 0xe6, 0xe8 };
> +static const u16 NCT6116_REG_FAN_PULSES[] = { 0xf6, 0xf6, 0xf6, 0xf6, 0xf5 };
> +static const u16 NCT6116_FAN_PULSE_SHIFT[] = { 0, 2, 4, 6, 6 };
> +
> +static const u8 NCT6116_REG_PWM_MODE[] = { 0xf3, 0xf3, 0xf3 };
> +static const u8 NCT6116_PWM_MODE_MASK[] = { 0x01, 0x02, 0x04 };
The above two defines match 6106.
> +static const u16 NCT6116_REG_PWM[] = { 0x119, 0x129, 0x139, 0x199, 0x1a9 };
> +static const u16 NCT6116_REG_FAN_MODE[] = { 0x113, 0x123, 0x133, 0x193, 0x1a3 };
> +static const u16 NCT6116_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130, 0x190, 0x1a0 };
> +static const u16 NCT6116_REG_TEMP_SOURCE[] = { 0xb0, 0xb1, 0xb2 };
NCT6116_REG_TEMP_SEL and NCT6116_REG_TEMP_SOURCE not needed (as above)
> +
> +static const u16 NCT6116_REG_CRITICAL_TEMP[] = {
> + 0x11a, 0x12a, 0x13a, 0x19a, 0x1aa };
> +static const u16 NCT6116_REG_CRITICAL_TEMP_TOLERANCE[] = {
> + 0x11b, 0x12b, 0x13b, 0x19b, 0x1ab };
> +
> +static const u16 NCT6116_REG_CRITICAL_PWM_ENABLE[] = {
> + 0x11c, 0x12c, 0x13c, 0x19c, 0x1ac };
> +static const u16 NCT6116_REG_CRITICAL_PWM[] = {
> + 0x11d, 0x12d, 0x13d, 0x19d, 0x1ad };
> +
> +static const u16 NCT6116_REG_FAN_STEP_UP_TIME[] = {
> + 0x114, 0x124, 0x134, 0x194, 0x1a4 };
> +static const u16 NCT6116_REG_FAN_STEP_DOWN_TIME[] = {
> + 0x115, 0x125, 0x135, 0x195, 0x1a5 };
> +static const u16 NCT6116_REG_FAN_STOP_OUTPUT[] = {
> + 0x116, 0x126, 0x136, 0x196, 0x1a6 };
> +static const u16 NCT6116_REG_FAN_START_OUTPUT[] = {
> + 0x117, 0x127, 0x137, 0x197, 0x1a7 };
> +static const u16 NCT6116_REG_FAN_STOP_TIME[] = {
> + 0x118, 0x128, 0x138, 0x198, 0x1a8 };
> +static const u16 NCT6116_REG_TOLERANCE_H[] = {
> + 0x112, 0x122, 0x132, 0x192, 0x1a2 };
> +
> +static const u16 NCT6116_REG_TARGET[] = {
> + 0x111, 0x121, 0x131, 0x191, 0x1a1 };
> +
> +static const u16 NCT6116_REG_AUTO_TEMP[] = {
> + 0x160, 0x170, 0x180, 0x1d0, 0x1e0 };
> +static const u16 NCT6116_REG_AUTO_PWM[] = {
> + 0x164, 0x174, 0x184, 0x1d4, 0x1e4 };
> +
> +static const s8 NCT6116_ALARM_BITS[] = {
> + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
> + 9, -1, -1, -1, -1, -1, -1, /* in8..in9 */
> + -1, /* unused */
> + 32, 33, 34, 35, 36, /* fan1..fan5 */
> + -1, -1, -1, /* unused */
> + 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
> + 48, -1 /* intrusion0, intrusion1 */
> +};
> +
> +static const s8 NCT6116_BEEP_BITS[] = {
> + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
> + 9, 10, 11, 12, -1, -1, -1, /* in8..in14 */
> + 32, /* global beep enable */
> + 24, 25, 26, 27, 28, /* fan1..fan5 */
> + -1, -1, -1, /* unused */
> + 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
> + 34, -1 /* intrusion0, intrusion1 */
> +};
> +
> static enum pwm_enable reg_to_pwm_enable(int pwm, int mode)
> {
> if (mode == 0 && pwm == 255)
> @@ -1308,6 +1384,11 @@
> return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
> reg == 0x111 || reg == 0x121 || reg == 0x131;
> + case nct6116:
> + return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> + reg == 0x26 || reg == 0x28 || reg == 0xe0 || reg == 0xe2 ||
> + reg == 0xe4 || reg == 0xe6 || reg == 0xe8 || reg == 0x111 ||
> + reg == 0x121 || reg == 0x131 || reg == 0x191 || reg == 0x1a1;
> case nct6775:
> return (((reg & 0xff00) == 0x100 ||
> (reg & 0xff00) == 0x200) &&
> @@ -1687,6 +1768,7 @@
> data->auto_pwm[i][data->auto_pwm_num] = 0xff;
> break;
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -3123,6 +3205,7 @@
> case nct6776:
> break; /* always enabled, nothing to do */
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -3549,6 +3632,28 @@
>
> fan3pin = !(cr24 & 0x80);
> pwm3pin = cr24 & 0x08;
> + } else if (data->kind == nct6116) {
> + int cr1a = superio_inb(sioreg, 0x1a);
> + int cr1b = superio_inb(sioreg, 0x1b);
> + int cr24 = superio_inb(sioreg, 0x24);
> + int cr2a = superio_inb(sioreg, 0x2a);
> + int cr2b = superio_inb(sioreg, 0x2b);
> + int cr2f = superio_inb(sioreg, 0x2f);
> +
This thing drives me crazy. Bear with me if I gat something
(or everything) wrong below.
> + fan3pin = !(cr2b & 0x10);
That seems correct.
> + if (!(cr2f & 0x10))
> + fan4pin = cr1a & 0x04;
> + else
> + fan4pin = 0;
else is unnecessary; fan4pin is false by default.
Overall,
fan4pin = !(cr2f & 0x10) && (cr1a & 0x04);
might be a bit easier and would avoid the if/else.
However, I think it should be
fan4pin = (cr2b & 0x80) || // pin 1
(!(cr2f & 0x10) && (cr1a & 0x04)); // pin 65
> +
> + if (!(cr1b & 0x03))
> + fan5pin = cr2a & 0x02;
> + else
> + fan5pin = cr2b & 0x80;
> +
fan5pin = (cr2b & 0x80) || // pin 126
(!(cr1b & 0x03) && (cr2a & 0x02)); // pin 96
> + pwm3pin = cr24 & 0x08;
The comments associated with GPIO8 group in combination with the pinout
suggest that it should be
pwm3pin = fan3pin && (cr24 & 0x08);
> + pwm4pin = cr2b & 0x80;
I think it is:
pwm4pin = (cr2b & 0x80) || // pin 2
(!(cr2f & 0x10) && (cr1a & 0x04)); // pin 66
or, in other words,
pwm4pin = fan4pin;
> + pwm5pin = pwm4pin;
Same here:
pwm5pin = (cr2b & 0x80) || // pin 127
(!(cr1b & 0x03) && (cr2a & 0x02)); // pin 96
or, in other words,
pwm5pin = fan5pin;
Does this make sense ?
> } else {
> /*
> * NCT6779D, NCT6791D, NCT6792D, NCT6793D, NCT6795D, NCT6796D,
> @@ -3821,6 +3926,79 @@
> reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
>
> break;
> + case nct6116:
> + data->in_num = 9;
> + data->pwm_num = 3;
> + data->auto_pwm_num = 4;
> + data->temp_fixed_num = 3;
> + data->num_temp_alarms = 3;
> + data->num_temp_beeps = 3;
> +
> + data->fan_from_reg = fan_from_reg13;
> + data->fan_from_reg_min = fan_from_reg13;
> +
> + data->temp_label = nct6776_temp_label;
> + data->temp_mask = NCT6776_TEMP_MASK;
> + data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
> +
> + data->REG_VBAT = NCT6106_REG_VBAT;
> + data->REG_DIODE = NCT6106_REG_DIODE;
> + data->DIODE_MASK = NCT6106_DIODE_MASK;
> + data->REG_VIN = NCT6106_REG_IN;
> + data->REG_IN_MINMAX[0] = NCT6106_REG_IN_MIN;
> + data->REG_IN_MINMAX[1] = NCT6106_REG_IN_MAX;
> + data->REG_TARGET = NCT6116_REG_TARGET;
> + data->REG_FAN = NCT6116_REG_FAN;
> + data->REG_FAN_MODE = NCT6116_REG_FAN_MODE;
> + data->REG_FAN_MIN = NCT6116_REG_FAN_MIN;
> + data->REG_FAN_PULSES = NCT6116_REG_FAN_PULSES;
> + data->FAN_PULSE_SHIFT = NCT6116_FAN_PULSE_SHIFT;
> + data->REG_FAN_TIME[0] = NCT6116_REG_FAN_STOP_TIME;
> + data->REG_FAN_TIME[1] = NCT6116_REG_FAN_STEP_UP_TIME;
> + data->REG_FAN_TIME[2] = NCT6116_REG_FAN_STEP_DOWN_TIME;
> + data->REG_TOLERANCE_H = NCT6116_REG_TOLERANCE_H;
> + data->REG_PWM[0] = NCT6116_REG_PWM;
> + data->REG_PWM[1] = NCT6116_REG_FAN_START_OUTPUT;
> + data->REG_PWM[2] = NCT6116_REG_FAN_STOP_OUTPUT;
> + data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
> + data->REG_PWM[6] = NCT6106_REG_WEIGHT_DUTY_BASE;
> + data->REG_PWM_READ = NCT6106_REG_PWM_READ;
> + data->REG_PWM_MODE = NCT6116_REG_PWM_MODE;
> + data->PWM_MODE_MASK = NCT6116_PWM_MODE_MASK;
> + data->REG_AUTO_TEMP = NCT6116_REG_AUTO_TEMP;
> + data->REG_AUTO_PWM = NCT6116_REG_AUTO_PWM;
> + data->REG_CRITICAL_TEMP = NCT6116_REG_CRITICAL_TEMP;
> + data->REG_CRITICAL_TEMP_TOLERANCE
> + = NCT6116_REG_CRITICAL_TEMP_TOLERANCE;
> + data->REG_CRITICAL_PWM_ENABLE = NCT6116_REG_CRITICAL_PWM_ENABLE;
> + data->CRITICAL_PWM_ENABLE_MASK
> + = NCT6106_CRITICAL_PWM_ENABLE_MASK;
> + data->REG_CRITICAL_PWM = NCT6116_REG_CRITICAL_PWM;
> + data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
> + data->REG_TEMP_SOURCE = NCT6116_REG_TEMP_SOURCE;
> + data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
> + data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
> + data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
> + data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
> + data->REG_WEIGHT_TEMP[2] = NCT6106_REG_WEIGHT_TEMP_BASE;
> + data->REG_ALARM = NCT6106_REG_ALARM;
> + data->ALARM_BITS = NCT6116_ALARM_BITS;
> + data->REG_BEEP = NCT6106_REG_BEEP;
> + data->BEEP_BITS = NCT6116_BEEP_BITS;
> +
> + reg_temp = NCT6116_REG_TEMP;
> + reg_temp_mon = NCT6106_REG_TEMP_MON;
> + num_reg_temp = ARRAY_SIZE(NCT6116_REG_TEMP);
> + num_reg_temp_mon = ARRAY_SIZE(NCT6106_REG_TEMP_MON);
> + reg_temp_over = NCT6116_REG_TEMP_OVER;
> + reg_temp_hyst = NCT6116_REG_TEMP_HYST;
> + reg_temp_config = NCT6116_REG_TEMP_CONFIG;
> + reg_temp_alternate = NCT6106_REG_TEMP_ALTERNATE;
> + reg_temp_crit = NCT6106_REG_TEMP_CRIT;
> + reg_temp_crit_l = NCT6116_REG_TEMP_CRIT_L;
> + reg_temp_crit_h = NCT6116_REG_TEMP_CRIT_H;
> +
> + break;
> case nct6775:
> data->in_num = 9;
> data->pwm_num = 3;
> @@ -4366,6 +4544,7 @@
> data->have_vid = (cr2a & 0x60) == 0x40;
> break;
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -4397,6 +4576,9 @@
> case nct6106:
> tmp |= 0xe0;
> break;
> + case nct6116:
> + tmp |= 0xe0;
> + break;
Please combine above case statements.
> case nct6775:
> tmp |= 0x1e;
> break;
> @@ -4590,6 +4772,9 @@
> case SIO_NCT6106_ID:
> sio_data->kind = nct6106;
> break;
> + case SIO_NCT6116_ID:
> + sio_data->kind = nct6116;
> + break;
> case SIO_NCT6775_ID:
> sio_data->kind = nct6775;
> break;
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-18 20:19 ` Björn Gerhart
@ 2019-07-19 18:01 ` Björn Gerhart
2019-07-19 19:37 ` Guenter Roeck
0 siblings, 1 reply; 12+ messages in thread
From: Björn Gerhart @ 2019-07-19 18:01 UTC (permalink / raw)
To: Guenter Roeck; +Cc: Hardware Monitoring
Hi Guenter,
I reworked the code after studying the details of the spec.
Changes:
- patch created against the tree of the kernel sources base dir
- only define the different registers in contrast to nct6106
- fixed details of the fan configuration
Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
---
diff -Naur a/drivers/hwmon/nct6775.c b/drivers/hwmon/nct6775.c
--- a/drivers/hwmon/nct6775.c 2019-07-19 15:29:34.960278982 +0200
+++ b/drivers/hwmon/nct6775.c 2019-07-19 15:29:47.332805721 +0200
@@ -34,6 +34,7 @@
*
* Chip #vin #fan #pwm #temp chip IDs man ID
* nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
+ * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
* nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
* nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
* nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
@@ -72,12 +73,13 @@
#define USE_ALTERNATE
-enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
- nct6795, nct6796, nct6797, nct6798 };
+enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
+ nct6793, nct6795, nct6796, nct6797, nct6798 };
/* used to set data->name = nct6775_device_names[data->sio_kind] */
static const char * const nct6775_device_names[] = {
"nct6106",
+ "nct6116",
"nct6775",
"nct6776",
"nct6779",
@@ -92,6 +94,7 @@
static const char * const nct6775_sio_names[] __initconst = {
"NCT6106D",
+ "NCT6116D",
"NCT6775F",
"NCT6776D/F",
"NCT6779D",
@@ -129,6 +132,7 @@
#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
#define SIO_NCT6106_ID 0xc450
+#define SIO_NCT6116_ID 0xd280
#define SIO_NCT6775_ID 0xb470
#define SIO_NCT6776_ID 0xc330
#define SIO_NCT6779_ID 0xc560
@@ -910,6 +914,78 @@
[12] = 0x205,
};
+/* NCT6112D/NCT6114D/NCT6116D specific data */
+
+static const u16 NCT6116_REG_TEMP[] = { 0x10, 0x11, 0x12 };
+static const u16 NCT6116_REG_TEMP_HYST[] = { 0xc3, 0xc7, 0xcb };
+static const u16 NCT6116_REG_TEMP_OVER[] = { 0xc2, 0xc6, 0xca };
+static const u16 NCT6116_REG_TEMP_CRIT_L[] = { 0xc0, 0xc4, 0xc8 };
+static const u16 NCT6116_REG_TEMP_CRIT_H[] = { 0xc1, 0xc5, 0xc9 };
+static const u16 NCT6116_REG_TEMP_CONFIG[] = { 0xb7, 0xb8, 0xb9 };
+
+static const u16 NCT6116_REG_FAN[] = { 0x20, 0x22, 0x24, 0x26, 0x28 };
+static const u16 NCT6116_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4, 0xe6, 0xe8 };
+static const u16 NCT6116_REG_FAN_PULSES[] = { 0xf6, 0xf6, 0xf6, 0xf6, 0xf5 };
+static const u16 NCT6116_FAN_PULSE_SHIFT[] = { 0, 2, 4, 6, 6 };
+
+static const u8 NCT6116_REG_PWM_MODE[] = { 0xf3, 0xf3, 0xf3 };
+static const u8 NCT6116_PWM_MODE_MASK[] = { 0x01, 0x02, 0x04 };
+static const u16 NCT6116_REG_PWM[] = { 0x119, 0x129, 0x139, 0x199, 0x1a9 };
+static const u16 NCT6116_REG_FAN_MODE[] = { 0x113, 0x123, 0x133, 0x193, 0x1a3 };
+static const u16 NCT6116_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130, 0x190, 0x1a0 };
+static const u16 NCT6116_REG_TEMP_SOURCE[] = { 0xb0, 0xb1, 0xb2 };
+
+static const u16 NCT6116_REG_CRITICAL_TEMP[] = {
+ 0x11a, 0x12a, 0x13a, 0x19a, 0x1aa };
+static const u16 NCT6116_REG_CRITICAL_TEMP_TOLERANCE[] = {
+ 0x11b, 0x12b, 0x13b, 0x19b, 0x1ab };
+
+static const u16 NCT6116_REG_CRITICAL_PWM_ENABLE[] = {
+ 0x11c, 0x12c, 0x13c, 0x19c, 0x1ac };
+static const u16 NCT6116_REG_CRITICAL_PWM[] = {
+ 0x11d, 0x12d, 0x13d, 0x19d, 0x1ad };
+
+static const u16 NCT6116_REG_FAN_STEP_UP_TIME[] = {
+ 0x114, 0x124, 0x134, 0x194, 0x1a4 };
+static const u16 NCT6116_REG_FAN_STEP_DOWN_TIME[] = {
+ 0x115, 0x125, 0x135, 0x195, 0x1a5 };
+static const u16 NCT6116_REG_FAN_STOP_OUTPUT[] = {
+ 0x116, 0x126, 0x136, 0x196, 0x1a6 };
+static const u16 NCT6116_REG_FAN_START_OUTPUT[] = {
+ 0x117, 0x127, 0x137, 0x197, 0x1a7 };
+static const u16 NCT6116_REG_FAN_STOP_TIME[] = {
+ 0x118, 0x128, 0x138, 0x198, 0x1a8 };
+static const u16 NCT6116_REG_TOLERANCE_H[] = {
+ 0x112, 0x122, 0x132, 0x192, 0x1a2 };
+
+static const u16 NCT6116_REG_TARGET[] = {
+ 0x111, 0x121, 0x131, 0x191, 0x1a1 };
+
+static const u16 NCT6116_REG_AUTO_TEMP[] = {
+ 0x160, 0x170, 0x180, 0x1d0, 0x1e0 };
+static const u16 NCT6116_REG_AUTO_PWM[] = {
+ 0x164, 0x174, 0x184, 0x1d4, 0x1e4 };
+
+static const s8 NCT6116_ALARM_BITS[] = {
+ 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
+ 9, -1, -1, -1, -1, -1, -1, /* in8..in9 */
+ -1, /* unused */
+ 32, 33, 34, 35, 36, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
+ 48, -1 /* intrusion0, intrusion1 */
+};
+
+static const s8 NCT6116_BEEP_BITS[] = {
+ 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
+ 9, 10, 11, 12, -1, -1, -1, /* in8..in14 */
+ 32, /* global beep enable */
+ 24, 25, 26, 27, 28, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
+ 34, -1 /* intrusion0, intrusion1 */
+};
+
static enum pwm_enable reg_to_pwm_enable(int pwm, int mode)
{
if (mode == 0 && pwm == 255)
@@ -1308,6 +1384,11 @@
return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
reg == 0x111 || reg == 0x121 || reg == 0x131;
+ case nct6116:
+ return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
+ reg == 0x26 || reg == 0x28 || reg == 0xe0 || reg == 0xe2 ||
+ reg == 0xe4 || reg == 0xe6 || reg == 0xe8 || reg == 0x111 ||
+ reg == 0x121 || reg == 0x131 || reg == 0x191 || reg == 0x1a1;
case nct6775:
return (((reg & 0xff00) == 0x100 ||
(reg & 0xff00) == 0x200) &&
@@ -1687,6 +1768,7 @@
data->auto_pwm[i][data->auto_pwm_num] = 0xff;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3123,6 +3205,7 @@
case nct6776:
break; /* always enabled, nothing to do */
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3549,6 +3632,28 @@
fan3pin = !(cr24 & 0x80);
pwm3pin = cr24 & 0x08;
+ } else if (data->kind == nct6116) {
+ int cr1a = superio_inb(sioreg, 0x1a);
+ int cr1b = superio_inb(sioreg, 0x1b);
+ int cr24 = superio_inb(sioreg, 0x24);
+ int cr2a = superio_inb(sioreg, 0x2a);
+ int cr2b = superio_inb(sioreg, 0x2b);
+ int cr2f = superio_inb(sioreg, 0x2f);
+
+ fan3pin = !(cr2b & 0x10);
+ if (!(cr2f & 0x10))
+ fan4pin = cr1a & 0x04;
+ else
+ fan4pin = 0;
+
+ if (!(cr1b & 0x03))
+ fan5pin = cr2a & 0x02;
+ else
+ fan5pin = cr2b & 0x80;
+
+ pwm3pin = cr24 & 0x08;
+ pwm4pin = cr2b & 0x80;
+ pwm5pin = pwm4pin;
} else {
/*
* NCT6779D, NCT6791D, NCT6792D, NCT6793D, NCT6795D, NCT6796D,
@@ -3821,6 +3926,79 @@
reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
break;
+ case nct6116:
+ data->in_num = 9;
+ data->pwm_num = 3;
+ data->auto_pwm_num = 4;
+ data->temp_fixed_num = 3;
+ data->num_temp_alarms = 3;
+ data->num_temp_beeps = 3;
+
+ data->fan_from_reg = fan_from_reg13;
+ data->fan_from_reg_min = fan_from_reg13;
+
+ data->temp_label = nct6776_temp_label;
+ data->temp_mask = NCT6776_TEMP_MASK;
+ data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
+
+ data->REG_VBAT = NCT6106_REG_VBAT;
+ data->REG_DIODE = NCT6106_REG_DIODE;
+ data->DIODE_MASK = NCT6106_DIODE_MASK;
+ data->REG_VIN = NCT6106_REG_IN;
+ data->REG_IN_MINMAX[0] = NCT6106_REG_IN_MIN;
+ data->REG_IN_MINMAX[1] = NCT6106_REG_IN_MAX;
+ data->REG_TARGET = NCT6116_REG_TARGET;
+ data->REG_FAN = NCT6116_REG_FAN;
+ data->REG_FAN_MODE = NCT6116_REG_FAN_MODE;
+ data->REG_FAN_MIN = NCT6116_REG_FAN_MIN;
+ data->REG_FAN_PULSES = NCT6116_REG_FAN_PULSES;
+ data->FAN_PULSE_SHIFT = NCT6116_FAN_PULSE_SHIFT;
+ data->REG_FAN_TIME[0] = NCT6116_REG_FAN_STOP_TIME;
+ data->REG_FAN_TIME[1] = NCT6116_REG_FAN_STEP_UP_TIME;
+ data->REG_FAN_TIME[2] = NCT6116_REG_FAN_STEP_DOWN_TIME;
+ data->REG_TOLERANCE_H = NCT6116_REG_TOLERANCE_H;
+ data->REG_PWM[0] = NCT6116_REG_PWM;
+ data->REG_PWM[1] = NCT6116_REG_FAN_START_OUTPUT;
+ data->REG_PWM[2] = NCT6116_REG_FAN_STOP_OUTPUT;
+ data->REG_PWM[5] = NCT6106_REG_WEIGHT_DUTY_STEP;
+ data->REG_PWM[6] = NCT6106_REG_WEIGHT_DUTY_BASE;
+ data->REG_PWM_READ = NCT6106_REG_PWM_READ;
+ data->REG_PWM_MODE = NCT6116_REG_PWM_MODE;
+ data->PWM_MODE_MASK = NCT6116_PWM_MODE_MASK;
+ data->REG_AUTO_TEMP = NCT6116_REG_AUTO_TEMP;
+ data->REG_AUTO_PWM = NCT6116_REG_AUTO_PWM;
+ data->REG_CRITICAL_TEMP = NCT6116_REG_CRITICAL_TEMP;
+ data->REG_CRITICAL_TEMP_TOLERANCE
+ = NCT6116_REG_CRITICAL_TEMP_TOLERANCE;
+ data->REG_CRITICAL_PWM_ENABLE = NCT6116_REG_CRITICAL_PWM_ENABLE;
+ data->CRITICAL_PWM_ENABLE_MASK
+ = NCT6106_CRITICAL_PWM_ENABLE_MASK;
+ data->REG_CRITICAL_PWM = NCT6116_REG_CRITICAL_PWM;
+ data->REG_TEMP_OFFSET = NCT6106_REG_TEMP_OFFSET;
+ data->REG_TEMP_SOURCE = NCT6116_REG_TEMP_SOURCE;
+ data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
+ data->REG_WEIGHT_TEMP_SEL = NCT6106_REG_WEIGHT_TEMP_SEL;
+ data->REG_WEIGHT_TEMP[0] = NCT6106_REG_WEIGHT_TEMP_STEP;
+ data->REG_WEIGHT_TEMP[1] = NCT6106_REG_WEIGHT_TEMP_STEP_TOL;
+ data->REG_WEIGHT_TEMP[2] = NCT6106_REG_WEIGHT_TEMP_BASE;
+ data->REG_ALARM = NCT6106_REG_ALARM;
+ data->ALARM_BITS = NCT6116_ALARM_BITS;
+ data->REG_BEEP = NCT6106_REG_BEEP;
+ data->BEEP_BITS = NCT6116_BEEP_BITS;
+
+ reg_temp = NCT6116_REG_TEMP;
+ reg_temp_mon = NCT6106_REG_TEMP_MON;
+ num_reg_temp = ARRAY_SIZE(NCT6116_REG_TEMP);
+ num_reg_temp_mon = ARRAY_SIZE(NCT6106_REG_TEMP_MON);
+ reg_temp_over = NCT6116_REG_TEMP_OVER;
+ reg_temp_hyst = NCT6116_REG_TEMP_HYST;
+ reg_temp_config = NCT6116_REG_TEMP_CONFIG;
+ reg_temp_alternate = NCT6106_REG_TEMP_ALTERNATE;
+ reg_temp_crit = NCT6106_REG_TEMP_CRIT;
+ reg_temp_crit_l = NCT6116_REG_TEMP_CRIT_L;
+ reg_temp_crit_h = NCT6116_REG_TEMP_CRIT_H;
+
+ break;
case nct6775:
data->in_num = 9;
data->pwm_num = 3;
@@ -4366,6 +4544,7 @@
data->have_vid = (cr2a & 0x60) == 0x40;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -4397,6 +4576,9 @@
case nct6106:
tmp |= 0xe0;
break;
+ case nct6116:
+ tmp |= 0xe0;
+ break;
case nct6775:
tmp |= 0x1e;
break;
@@ -4590,6 +4772,9 @@
case SIO_NCT6106_ID:
sio_data->kind = nct6106;
break;
+ case SIO_NCT6116_ID:
+ sio_data->kind = nct6116;
+ break;
case SIO_NCT6775_ID:
sio_data->kind = nct6775;
break;
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-16 13:44 ` Guenter Roeck
@ 2019-07-18 20:19 ` Björn Gerhart
2019-07-19 18:01 ` Björn Gerhart
0 siblings, 1 reply; 12+ messages in thread
From: Björn Gerhart @ 2019-07-18 20:19 UTC (permalink / raw)
To: Guenter Roeck; +Cc: Hardware Monitoring
Thanks Guenter! Please see my comments below.
> Am 16.07.2019 um 15:44 schrieb Guenter Roeck <linux@roeck-us.net>:
>
> On 7/15/19 9:47 AM, Björn Gerhart wrote:
>> Hello again and thanks for the early feedback! This is the re-worked patch of the one I sent last week. It’s created against kernel 5.1.15 and already depends on the preceding patch concerning the same code.
>> The nct6116 is the successor model of nct6106. Mainly, I’m unsure if certain details of the spec are mapped correctly to the code. These details are:
>> - NCT6116_BEEP_BITS
>
> looks good to me.
>
>> - int cr24 (cr23 is new, and I’m unsure if the code has to get modified therefore)
>
> I don't see cr23h in the datasheet available to me. What am I missing ?
>
My fault - there is no cr23h at all.
> But, yes, there are differences:
>
> nct6116:
> cr1ah[2] determines AUXFANIN1/AUXFANOUT1 settings
> cr1b[1-1] and cr2a[1] determine AUXFANIN2/AUXFANOUT2 settings
> cr2b[7] is an alternate for AUXFANIN1/AUXFANOUT1
> cr2b[4] enable AUXFANIN0/AUXFANOUT0 (same as AUXFANIN/AUXFANOUT ?) on pin 6, 14
> cr24[3] enables AUXFANOUT on pin 14
>
> nct6106:
> cr24[7] enables AUXFANIN on pin 6
> cr24[3] enables AUXFANOUT on pin 14
>
This part turns to be the most tricky one. For me the meaning/interpretation of all the possible options is quite confusing. Especially when some contents might get mirrored to different registers.
The nct6116 covers 5 fans in total, and I identified fan4 as AUXFAN1 and fan5 as AUXFAN2. So respectively, AUXFAN0 should be the same as AUXFAN and reference to fan3.
Following, the piece of code which I hope to reflect this part of the datasheet properly:
{ else if (data->kind == nct6116) {
int cr1a = superio_inb(sioreg, 0x1a);
int cr1b = superio_inb(sioreg, 0x1b);
int cr24 = superio_inb(sioreg, 0x24);
int cr2a = superio_inb(sioreg, 0x2a);
pwm3pin = cr24 & 0x08;
fan3pin = cr2b & 0x10;
pwm4pin = cr1a & 0x04;
if !(cr1b & 0x03) {
pwm5pin = cr2a & 0x02;
}
The registers described in the spec do not differ between pwmpin and fanpin. Which one shall get used?
If the same content is good for in and out, is pwm4pin == fan4pin?
>> - NCT6116_REG_FAN_PULSES
>> - NCT6116_FAN_PULSE_SHIFT
>> - NCT6116_ALARM_BITS
>> With the nct6116 wired on my mainboard, the sensors command seems to work as I would expect.
>> Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
>> ---
>> --- nct6775-5.1.15-1.el7.elrepo.x86_64-bugfixed/nct6775.c 2019-07-10 17:08:30.710690605 +0200
>> +++ nct6775/nct6775.c 2019-07-10 17:30:38.012416414 +0200
>> @@ -34,6 +34,7 @@
>> *
>> * Chip #vin #fan #pwm #temp chip IDs man ID
>> * nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
>> + * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
>> * nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
>> * nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
>> * nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
>> @@ -72,12 +73,13 @@
>> #define USE_ALTERNATE
>> -enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
>> - nct6795, nct6796, nct6797, nct6798 };
>> +enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
>> + nct6793, nct6795, nct6796, nct6797, nct6798 };
>> /* used to set data->name = nct6775_device_names[data->sio_kind] */
>> static const char * const nct6775_device_names[] = {
>> "nct6106",
>> + "nct6116",
>> "nct6775",
>> "nct6776",
>> "nct6779",
>> @@ -92,6 +94,7 @@
>> static const char * const nct6775_sio_names[] __initconst = {
>> "NCT6106D",
>> + "NCT6116D",
>> "NCT6775F",
>> "NCT6776D/F",
>> "NCT6779D",
>> @@ -129,6 +132,7 @@
>> #define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
>> #define SIO_NCT6106_ID 0xc450
>> +#define SIO_NCT6116_ID 0xd280
>> #define SIO_NCT6775_ID 0xb470
>> #define SIO_NCT6776_ID 0xc330
>> #define SIO_NCT6779_ID 0xc560
>> @@ -910,6 +914,119 @@
>> [12] = 0x205,
>> };
>> +/* NCT6112D/NCT6114D/NCT6116D specific data */
>> +
>> +#define NCT6116_REG_VBAT 0x318
>> +#define NCT6116_REG_DIODE 0x319
>> +#define NCT6116_DIODE_MASK 0x01
>> +
>> +static const u16 NCT6116_REG_IN_MAX[] = {
>> + 0x90, 0x92, 0x94, 0x96, 0x98, 0x9a, 0x9e, 0xa0, 0xa2 };
>> +static const u16 NCT6116_REG_IN_MIN[] = {
>> + 0x91, 0x93, 0x95, 0x97, 0x99, 0x9b, 0x9f, 0xa1, 0xa3 };
>> +static const u16 NCT6116_REG_IN[] = {
>> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x07, 0x08, 0x09 };
>> +
>> +static const u16 NCT6116_REG_TEMP[] = { 0x10, 0x11, 0x12 };
>> +static const u16 NCT6116_REG_TEMP_MON[] = { 0x18, 0x19, 0x1a };
>> +static const u16 NCT6116_REG_TEMP_HYST[] = { 0xc3, 0xc7, 0xcb };
>> +static const u16 NCT6116_REG_TEMP_OVER[] = { 0xc2, 0xc6, 0xca };
>> +static const u16 NCT6116_REG_TEMP_CRIT_L[] = { 0xc0, 0xc4, 0xc8 };
>> +static const u16 NCT6116_REG_TEMP_CRIT_H[] = { 0xc1, 0xc5, 0xc9 };
>> +static const u16 NCT6116_REG_TEMP_OFFSET[] = { 0x311, 0x312, 0x313 };
>> +static const u16 NCT6116_REG_TEMP_CONFIG[] = { 0xb7, 0xb8, 0xb9 };
>> +
>> +static const u16 NCT6116_REG_FAN[] = { 0x20, 0x22, 0x24, 0x26, 0x28 };
>> +static const u16 NCT6116_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4, 0xe6, 0xe8 };
>> +static const u16 NCT6116_REG_FAN_PULSES[] = { 0xf6, 0xf6, 0xf6, 0xf6, 0xf5 };
>> +static const u16 NCT6116_FAN_PULSE_SHIFT[] = { 0, 2, 4, 6, 6 };
>> +
>> +static const u8 NCT6116_REG_PWM_MODE[] = { 0xf3, 0xf3, 0xf3 };
>> +static const u8 NCT6116_PWM_MODE_MASK[] = { 0x01, 0x02, 0x04 };
>> +static const u16 NCT6116_REG_PWM[] = { 0x119, 0x129, 0x139, 0x199, 0x1a9 };
>> +static const u16 NCT6116_REG_PWM_READ[] = { 0x4a, 0x4b, 0x4c };
>> +static const u16 NCT6116_REG_FAN_MODE[] = { 0x113, 0x123, 0x133, 0x193, 0x1a3 };
>> +static const u16 NCT6116_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130, 0x190, 0x1a0 };
>> +static const u16 NCT6116_REG_TEMP_SOURCE[] = { 0xb0, 0xb1, 0xb2 };
>> +
>> +static const u16 NCT6116_REG_CRITICAL_TEMP[] = {
>> + 0x11a, 0x12a, 0x13a, 0x19a, 0x1aa };
>> +static const u16 NCT6116_REG_CRITICAL_TEMP_TOLERANCE[] = {
>> + 0x11b, 0x12b, 0x13b, 0x19b, 0x1ab };
>> +
>> +static const u16 NCT6116_REG_CRITICAL_PWM_ENABLE[] = {
>> + 0x11c, 0x12c, 0x13c, 0x19c, 0x1ac };
>> +#define NCT6116_CRITICAL_PWM_ENABLE_MASK 0x10
>> +static const u16 NCT6116_REG_CRITICAL_PWM[] = {
>> + 0x11d, 0x12d, 0x13d, 0x19d, 0x1ad };
>> +
>> +static const u16 NCT6116_REG_FAN_STEP_UP_TIME[] = {
>> + 0x114, 0x124, 0x134, 0x194, 0x1a4 };
>> +static const u16 NCT6116_REG_FAN_STEP_DOWN_TIME[] = {
>> + 0x115, 0x125, 0x135, 0x195, 0x1a5 };
>> +static const u16 NCT6116_REG_FAN_STOP_OUTPUT[] = {
>> + 0x116, 0x126, 0x136, 0x196, 0x1a6 };
>> +static const u16 NCT6116_REG_FAN_START_OUTPUT[] = {
>> + 0x117, 0x127, 0x137, 0x197, 0x1a7 };
>> +static const u16 NCT6116_REG_FAN_STOP_TIME[] = {
>> + 0x118, 0x128, 0x138, 0x198, 0x1a8 };
>> +static const u16 NCT6116_REG_TOLERANCE_H[] = {
>> + 0x112, 0x122, 0x132, 0x192, 0x1a2 };
>> +
>> +static const u16 NCT6116_REG_TARGET[] = {
>> + 0x111, 0x121, 0x131, 0x191, 0x1a1 };
>> +
>> +static const u16 NCT6116_REG_WEIGHT_TEMP_SEL[] = { 0x168, 0x178, 0x188 };
>> +static const u16 NCT6116_REG_WEIGHT_TEMP_STEP[] = { 0x169, 0x179, 0x189 };
>> +static const u16 NCT6116_REG_WEIGHT_TEMP_STEP_TOL[] = { 0x16a, 0x17a, 0x18a };
>> +static const u16 NCT6116_REG_WEIGHT_DUTY_STEP[] = { 0x16b, 0x17b, 0x18b };
>> +static const u16 NCT6116_REG_WEIGHT_TEMP_BASE[] = { 0x16c, 0x17c, 0x18c };
>> +static const u16 NCT6116_REG_WEIGHT_DUTY_BASE[] = { 0x16d, 0x17d, 0x18d };
>> +
>> +static const u16 NCT6116_REG_AUTO_TEMP[] = {
>> + 0x160, 0x170, 0x180, 0x1d0, 0x1e0 };
>> +static const u16 NCT6116_REG_AUTO_PWM[] = {
>> + 0x164, 0x174, 0x184, 0x1d4, 0x1e4 };
>> +
>> +static const u16 NCT6116_REG_ALARM[NUM_REG_ALARM] = {
>> + 0x77, 0x78, 0x79, 0x7a, 0x7b, 0x7c, 0x7d };
>> +
>> +static const s8 NCT6116_ALARM_BITS[] = {
>> + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
>> + 9, -1, -1, -1, -1, -1, -1, /* in8..in9 */
>> + -1, /* unused */
>> + 32, 33, 34, 35, 36, /* fan1..fan5 */
>> + -1, -1, -1, /* unused */
>> + 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
>> + 48, -1 /* intrusion0, intrusion1 */
>> +};
>> +
>> +static const u16 NCT6116_REG_BEEP[NUM_REG_BEEP] = {
>> + 0x3c0, 0x3c1, 0x3c2, 0x3c3, 0x3c4 };
>> +
>> +static const s8 NCT6116_BEEP_BITS[] = {
>> + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
>> + 9, 10, 11, 12, -1, -1, -1, /* in8..in14 */
>> + 32, /* global beep enable */
>> + 24, 25, 26, 27, 28, /* fan1..fan5 */
>> + -1, -1, -1, /* unused */
>> + 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
>> + 34, -1 /* intrusion0, intrusion1 */
>> +};
>> +
>> +static const u16 NCT6116_REG_TEMP_ALTERNATE[32] = {
>> + [14] = 0x51,
>> + [15] = 0x52,
>> + [16] = 0x54,
>> +};
>> +
>> +static const u16 NCT6116_REG_TEMP_CRIT[32] = {
>> + [11] = 0x204,
>> + [12] = 0x205,
>> +};
>> +
> Unfortunately, this time you duplicated data for _all_ registers, not just
> the different ones. Idea is to retain the registers which don't change
> and only list the changed registers for a new chip.
>
>> +
>> +
> No more than one empty line, please.
>
>> static enum pwm_enable reg_to_pwm_enable(int pwm, int mode)
>> {
>> if (mode == 0 && pwm == 255)
>> @@ -1308,6 +1425,11 @@
>> return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
>> reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
>> reg == 0x111 || reg == 0x121 || reg == 0x131;
>> + case nct6116:
>> + return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
>> + reg == 0x26 || reg == 0x28 || reg == 0xe0 || reg == 0xe2 ||
>> + reg == 0xe4 || reg == 0xe6 || reg == 0xe8 || reg == 0x111 ||
>> + reg == 0x121 || reg == 0x131 || reg == 0x191 || reg == 0x1a1;
>> case nct6775:
>> return (((reg & 0xff00) == 0x100 ||
>> (reg & 0xff00) == 0x200) &&
>> @@ -1687,6 +1809,7 @@
>> data->auto_pwm[i][data->auto_pwm_num] = 0xff;
>> break;
>> case nct6106:
>> + case nct6116:
>> case nct6779:
>> case nct6791:
>> case nct6792:
>> @@ -3123,6 +3246,7 @@
>> case nct6776:
>> break; /* always enabled, nothing to do */
>> case nct6106:
>> + case nct6116:
>> case nct6779:
>> case nct6791:
>> case nct6792:
>> @@ -3544,7 +3668,7 @@
>> fan4min = fan4pin;
>> pwm3pin = fan3pin;
>> - } else if (data->kind == nct6106) {
>> + } else if ((data->kind == nct6106) || (data->kind == nct6116)) {
>
> nct6116 will need a separate if statement per above.
>
>> int cr24 = superio_inb(sioreg, 0x24);
>> fan3pin = !(cr24 & 0x80);
>> @@ -3821,6 +3945,79 @@
>> reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
>> break;
>> + case nct6116:
>> + data->in_num = 9;
>> + data->pwm_num = 3;
>> + data->auto_pwm_num = 4;
>> + data->temp_fixed_num = 3;
>> + data->num_temp_alarms = 3;
>> + data->num_temp_beeps = 3;
>> +
>> + data->fan_from_reg = fan_from_reg13;
>> + data->fan_from_reg_min = fan_from_reg13;
>> +
>> + data->temp_label = nct6776_temp_label;
>> + data->temp_mask = NCT6776_TEMP_MASK;
>> + data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
>> +
>> + data->REG_VBAT = NCT6116_REG_VBAT;
>> + data->REG_DIODE = NCT6116_REG_DIODE;
>> + data->DIODE_MASK = NCT6116_DIODE_MASK;
>> + data->REG_VIN = NCT6116_REG_IN;
>> + data->REG_IN_MINMAX[0] = NCT6116_REG_IN_MIN;
>> + data->REG_IN_MINMAX[1] = NCT6116_REG_IN_MAX;
>> + data->REG_TARGET = NCT6116_REG_TARGET;
>> + data->REG_FAN = NCT6116_REG_FAN;
>> + data->REG_FAN_MODE = NCT6116_REG_FAN_MODE;
>> + data->REG_FAN_MIN = NCT6116_REG_FAN_MIN;
>> + data->REG_FAN_PULSES = NCT6116_REG_FAN_PULSES;
>> + data->FAN_PULSE_SHIFT = NCT6116_FAN_PULSE_SHIFT;
>> + data->REG_FAN_TIME[0] = NCT6116_REG_FAN_STOP_TIME;
>> + data->REG_FAN_TIME[1] = NCT6116_REG_FAN_STEP_UP_TIME;
>> + data->REG_FAN_TIME[2] = NCT6116_REG_FAN_STEP_DOWN_TIME;
>> + data->REG_TOLERANCE_H = NCT6116_REG_TOLERANCE_H;
>> + data->REG_PWM[0] = NCT6116_REG_PWM;
>> + data->REG_PWM[1] = NCT6116_REG_FAN_START_OUTPUT;
>> + data->REG_PWM[2] = NCT6116_REG_FAN_STOP_OUTPUT;
>> + data->REG_PWM[5] = NCT6116_REG_WEIGHT_DUTY_STEP;
>> + data->REG_PWM[6] = NCT6116_REG_WEIGHT_DUTY_BASE;
>> + data->REG_PWM_READ = NCT6116_REG_PWM_READ;
>> + data->REG_PWM_MODE = NCT6116_REG_PWM_MODE;
>> + data->PWM_MODE_MASK = NCT6116_PWM_MODE_MASK;
>> + data->REG_AUTO_TEMP = NCT6116_REG_AUTO_TEMP;
>> + data->REG_AUTO_PWM = NCT6116_REG_AUTO_PWM;
>> + data->REG_CRITICAL_TEMP = NCT6116_REG_CRITICAL_TEMP;
>> + data->REG_CRITICAL_TEMP_TOLERANCE
>> + = NCT6116_REG_CRITICAL_TEMP_TOLERANCE;
>> + data->REG_CRITICAL_PWM_ENABLE = NCT6116_REG_CRITICAL_PWM_ENABLE;
>> + data->CRITICAL_PWM_ENABLE_MASK
>> + = NCT6116_CRITICAL_PWM_ENABLE_MASK;
>> + data->REG_CRITICAL_PWM = NCT6116_REG_CRITICAL_PWM;
>> + data->REG_TEMP_OFFSET = NCT6116_REG_TEMP_OFFSET;
>> + data->REG_TEMP_SOURCE = NCT6116_REG_TEMP_SOURCE;
>> + data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
>> + data->REG_WEIGHT_TEMP_SEL = NCT6116_REG_WEIGHT_TEMP_SEL;
>> + data->REG_WEIGHT_TEMP[0] = NCT6116_REG_WEIGHT_TEMP_STEP;
>> + data->REG_WEIGHT_TEMP[1] = NCT6116_REG_WEIGHT_TEMP_STEP_TOL;
>> + data->REG_WEIGHT_TEMP[2] = NCT6116_REG_WEIGHT_TEMP_BASE;
>> + data->REG_ALARM = NCT6116_REG_ALARM;
>> + data->ALARM_BITS = NCT6116_ALARM_BITS;
>> + data->REG_BEEP = NCT6116_REG_BEEP;
>> + data->BEEP_BITS = NCT6116_BEEP_BITS;
>> +
>> + reg_temp = NCT6116_REG_TEMP;
>> + reg_temp_mon = NCT6116_REG_TEMP_MON;
>> + num_reg_temp = ARRAY_SIZE(NCT6116_REG_TEMP);
>> + num_reg_temp_mon = ARRAY_SIZE(NCT6116_REG_TEMP_MON);
>> + reg_temp_over = NCT6116_REG_TEMP_OVER;
>> + reg_temp_hyst = NCT6116_REG_TEMP_HYST;
>> + reg_temp_config = NCT6116_REG_TEMP_CONFIG;
>> + reg_temp_alternate = NCT6116_REG_TEMP_ALTERNATE;
>> + reg_temp_crit = NCT6116_REG_TEMP_CRIT;
>> + reg_temp_crit_l = NCT6116_REG_TEMP_CRIT_L;
>> + reg_temp_crit_h = NCT6116_REG_TEMP_CRIT_H;
>> +
>> + break;
>> case nct6775:
>> data->in_num = 9;
>> data->pwm_num = 3;
>> @@ -4366,6 +4563,7 @@
>> data->have_vid = (cr2a & 0x60) == 0x40;
>> break;
>> case nct6106:
>> + case nct6116:
>> case nct6779:
>> case nct6791:
>> case nct6792:
>> @@ -4397,6 +4595,9 @@
>> case nct6106:
>> tmp |= 0xe0;
>> break;
>> + case nct6116:
>> + tmp |= 0xe0;
>> + break;
>> case nct6775:
>> tmp |= 0x1e;
>> break;
>> @@ -4590,6 +4791,9 @@
>> case SIO_NCT6106_ID:
>> sio_data->kind = nct6106;
>> break;
>> + case SIO_NCT6116_ID:
>> + sio_data->kind = nct6116;
>> + break;
>> case SIO_NCT6775_ID:
>> sio_data->kind = nct6775;
>> break;
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] hwmon: (nct6775) Integrated new model nct6116
2019-07-15 16:47 Björn Gerhart
@ 2019-07-16 13:44 ` Guenter Roeck
2019-07-18 20:19 ` Björn Gerhart
0 siblings, 1 reply; 12+ messages in thread
From: Guenter Roeck @ 2019-07-16 13:44 UTC (permalink / raw)
To: Björn Gerhart, Hardware Monitoring
On 7/15/19 9:47 AM, Björn Gerhart wrote:
> Hello again and thanks for the early feedback! This is the re-worked patch of the one I sent last week. It’s created against kernel 5.1.15 and already depends on the preceding patch concerning the same code.
>
> The nct6116 is the successor model of nct6106. Mainly, I’m unsure if certain details of the spec are mapped correctly to the code. These details are:
> - NCT6116_BEEP_BITS
looks good to me.
> - int cr24 (cr23 is new, and I’m unsure if the code has to get modified therefore)
I don't see cr23h in the datasheet available to me. What am I missing ?
But, yes, there are differences:
nct6116:
cr1ah[2] determines AUXFANIN1/AUXFANOUT1 settings
cr1b[1-1] and cr2a[1] determine AUXFANIN2/AUXFANOUT2 settings
cr2b[7] is an alternate for AUXFANIN1/AUXFANOUT1
cr2b[4] enable AUXFANIN0/AUXFANOUT0 (same as AUXFANIN/AUXFANOUT ?) on pin 6, 14
cr24[3] enables AUXFANOUT on pin 14
nct6106:
cr24[7] enables AUXFANIN on pin 6
cr24[3] enables AUXFANOUT on pin 14
> - NCT6116_REG_FAN_PULSES
> - NCT6116_FAN_PULSE_SHIFT
> - NCT6116_ALARM_BITS
>
> With the nct6116 wired on my mainboard, the sensors command seems to work as I would expect.
>
> Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
> ---
> --- nct6775-5.1.15-1.el7.elrepo.x86_64-bugfixed/nct6775.c 2019-07-10 17:08:30.710690605 +0200
> +++ nct6775/nct6775.c 2019-07-10 17:30:38.012416414 +0200
> @@ -34,6 +34,7 @@
> *
> * Chip #vin #fan #pwm #temp chip IDs man ID
> * nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
> + * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
> * nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
> * nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
> * nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
> @@ -72,12 +73,13 @@
>
> #define USE_ALTERNATE
>
> -enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
> - nct6795, nct6796, nct6797, nct6798 };
> +enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
> + nct6793, nct6795, nct6796, nct6797, nct6798 };
>
> /* used to set data->name = nct6775_device_names[data->sio_kind] */
> static const char * const nct6775_device_names[] = {
> "nct6106",
> + "nct6116",
> "nct6775",
> "nct6776",
> "nct6779",
> @@ -92,6 +94,7 @@
>
> static const char * const nct6775_sio_names[] __initconst = {
> "NCT6106D",
> + "NCT6116D",
> "NCT6775F",
> "NCT6776D/F",
> "NCT6779D",
> @@ -129,6 +132,7 @@
> #define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
>
> #define SIO_NCT6106_ID 0xc450
> +#define SIO_NCT6116_ID 0xd280
> #define SIO_NCT6775_ID 0xb470
> #define SIO_NCT6776_ID 0xc330
> #define SIO_NCT6779_ID 0xc560
> @@ -910,6 +914,119 @@
> [12] = 0x205,
> };
>
> +/* NCT6112D/NCT6114D/NCT6116D specific data */
> +
> +#define NCT6116_REG_VBAT 0x318
> +#define NCT6116_REG_DIODE 0x319
> +#define NCT6116_DIODE_MASK 0x01
> +
> +static const u16 NCT6116_REG_IN_MAX[] = {
> + 0x90, 0x92, 0x94, 0x96, 0x98, 0x9a, 0x9e, 0xa0, 0xa2 };
> +static const u16 NCT6116_REG_IN_MIN[] = {
> + 0x91, 0x93, 0x95, 0x97, 0x99, 0x9b, 0x9f, 0xa1, 0xa3 };
> +static const u16 NCT6116_REG_IN[] = {
> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x07, 0x08, 0x09 };
> +
> +static const u16 NCT6116_REG_TEMP[] = { 0x10, 0x11, 0x12 };
> +static const u16 NCT6116_REG_TEMP_MON[] = { 0x18, 0x19, 0x1a };
> +static const u16 NCT6116_REG_TEMP_HYST[] = { 0xc3, 0xc7, 0xcb };
> +static const u16 NCT6116_REG_TEMP_OVER[] = { 0xc2, 0xc6, 0xca };
> +static const u16 NCT6116_REG_TEMP_CRIT_L[] = { 0xc0, 0xc4, 0xc8 };
> +static const u16 NCT6116_REG_TEMP_CRIT_H[] = { 0xc1, 0xc5, 0xc9 };
> +static const u16 NCT6116_REG_TEMP_OFFSET[] = { 0x311, 0x312, 0x313 };
> +static const u16 NCT6116_REG_TEMP_CONFIG[] = { 0xb7, 0xb8, 0xb9 };
> +
> +static const u16 NCT6116_REG_FAN[] = { 0x20, 0x22, 0x24, 0x26, 0x28 };
> +static const u16 NCT6116_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4, 0xe6, 0xe8 };
> +static const u16 NCT6116_REG_FAN_PULSES[] = { 0xf6, 0xf6, 0xf6, 0xf6, 0xf5 };
> +static const u16 NCT6116_FAN_PULSE_SHIFT[] = { 0, 2, 4, 6, 6 };
> +
> +static const u8 NCT6116_REG_PWM_MODE[] = { 0xf3, 0xf3, 0xf3 };
> +static const u8 NCT6116_PWM_MODE_MASK[] = { 0x01, 0x02, 0x04 };
> +static const u16 NCT6116_REG_PWM[] = { 0x119, 0x129, 0x139, 0x199, 0x1a9 };
> +static const u16 NCT6116_REG_PWM_READ[] = { 0x4a, 0x4b, 0x4c };
> +static const u16 NCT6116_REG_FAN_MODE[] = { 0x113, 0x123, 0x133, 0x193, 0x1a3 };
> +static const u16 NCT6116_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130, 0x190, 0x1a0 };
> +static const u16 NCT6116_REG_TEMP_SOURCE[] = { 0xb0, 0xb1, 0xb2 };
> +
> +static const u16 NCT6116_REG_CRITICAL_TEMP[] = {
> + 0x11a, 0x12a, 0x13a, 0x19a, 0x1aa };
> +static const u16 NCT6116_REG_CRITICAL_TEMP_TOLERANCE[] = {
> + 0x11b, 0x12b, 0x13b, 0x19b, 0x1ab };
> +
> +static const u16 NCT6116_REG_CRITICAL_PWM_ENABLE[] = {
> + 0x11c, 0x12c, 0x13c, 0x19c, 0x1ac };
> +#define NCT6116_CRITICAL_PWM_ENABLE_MASK 0x10
> +static const u16 NCT6116_REG_CRITICAL_PWM[] = {
> + 0x11d, 0x12d, 0x13d, 0x19d, 0x1ad };
> +
> +static const u16 NCT6116_REG_FAN_STEP_UP_TIME[] = {
> + 0x114, 0x124, 0x134, 0x194, 0x1a4 };
> +static const u16 NCT6116_REG_FAN_STEP_DOWN_TIME[] = {
> + 0x115, 0x125, 0x135, 0x195, 0x1a5 };
> +static const u16 NCT6116_REG_FAN_STOP_OUTPUT[] = {
> + 0x116, 0x126, 0x136, 0x196, 0x1a6 };
> +static const u16 NCT6116_REG_FAN_START_OUTPUT[] = {
> + 0x117, 0x127, 0x137, 0x197, 0x1a7 };
> +static const u16 NCT6116_REG_FAN_STOP_TIME[] = {
> + 0x118, 0x128, 0x138, 0x198, 0x1a8 };
> +static const u16 NCT6116_REG_TOLERANCE_H[] = {
> + 0x112, 0x122, 0x132, 0x192, 0x1a2 };
> +
> +static const u16 NCT6116_REG_TARGET[] = {
> + 0x111, 0x121, 0x131, 0x191, 0x1a1 };
> +
> +static const u16 NCT6116_REG_WEIGHT_TEMP_SEL[] = { 0x168, 0x178, 0x188 };
> +static const u16 NCT6116_REG_WEIGHT_TEMP_STEP[] = { 0x169, 0x179, 0x189 };
> +static const u16 NCT6116_REG_WEIGHT_TEMP_STEP_TOL[] = { 0x16a, 0x17a, 0x18a };
> +static const u16 NCT6116_REG_WEIGHT_DUTY_STEP[] = { 0x16b, 0x17b, 0x18b };
> +static const u16 NCT6116_REG_WEIGHT_TEMP_BASE[] = { 0x16c, 0x17c, 0x18c };
> +static const u16 NCT6116_REG_WEIGHT_DUTY_BASE[] = { 0x16d, 0x17d, 0x18d };
> +
> +static const u16 NCT6116_REG_AUTO_TEMP[] = {
> + 0x160, 0x170, 0x180, 0x1d0, 0x1e0 };
> +static const u16 NCT6116_REG_AUTO_PWM[] = {
> + 0x164, 0x174, 0x184, 0x1d4, 0x1e4 };
> +
> +static const u16 NCT6116_REG_ALARM[NUM_REG_ALARM] = {
> + 0x77, 0x78, 0x79, 0x7a, 0x7b, 0x7c, 0x7d };
> +
> +static const s8 NCT6116_ALARM_BITS[] = {
> + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
> + 9, -1, -1, -1, -1, -1, -1, /* in8..in9 */
> + -1, /* unused */
> + 32, 33, 34, 35, 36, /* fan1..fan5 */
> + -1, -1, -1, /* unused */
> + 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
> + 48, -1 /* intrusion0, intrusion1 */
> +};
> +
> +static const u16 NCT6116_REG_BEEP[NUM_REG_BEEP] = {
> + 0x3c0, 0x3c1, 0x3c2, 0x3c3, 0x3c4 };
> +
> +static const s8 NCT6116_BEEP_BITS[] = {
> + 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
> + 9, 10, 11, 12, -1, -1, -1, /* in8..in14 */
> + 32, /* global beep enable */
> + 24, 25, 26, 27, 28, /* fan1..fan5 */
> + -1, -1, -1, /* unused */
> + 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
> + 34, -1 /* intrusion0, intrusion1 */
> +};
> +
> +static const u16 NCT6116_REG_TEMP_ALTERNATE[32] = {
> + [14] = 0x51,
> + [15] = 0x52,
> + [16] = 0x54,
> +};
> +
> +static const u16 NCT6116_REG_TEMP_CRIT[32] = {
> + [11] = 0x204,
> + [12] = 0x205,
> +};
> +
Unfortunately, this time you duplicated data for _all_ registers, not just
the different ones. Idea is to retain the registers which don't change
and only list the changed registers for a new chip.
> +
> +
No more than one empty line, please.
> static enum pwm_enable reg_to_pwm_enable(int pwm, int mode)
> {
> if (mode == 0 && pwm == 255)
> @@ -1308,6 +1425,11 @@
> return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
> reg == 0x111 || reg == 0x121 || reg == 0x131;
> + case nct6116:
> + return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
> + reg == 0x26 || reg == 0x28 || reg == 0xe0 || reg == 0xe2 ||
> + reg == 0xe4 || reg == 0xe6 || reg == 0xe8 || reg == 0x111 ||
> + reg == 0x121 || reg == 0x131 || reg == 0x191 || reg == 0x1a1;
> case nct6775:
> return (((reg & 0xff00) == 0x100 ||
> (reg & 0xff00) == 0x200) &&
> @@ -1687,6 +1809,7 @@
> data->auto_pwm[i][data->auto_pwm_num] = 0xff;
> break;
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -3123,6 +3246,7 @@
> case nct6776:
> break; /* always enabled, nothing to do */
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -3544,7 +3668,7 @@
>
> fan4min = fan4pin;
> pwm3pin = fan3pin;
> - } else if (data->kind == nct6106) {
> + } else if ((data->kind == nct6106) || (data->kind == nct6116)) {
nct6116 will need a separate if statement per above.
> int cr24 = superio_inb(sioreg, 0x24);
>
> fan3pin = !(cr24 & 0x80);
> @@ -3821,6 +3945,79 @@
> reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
>
> break;
> + case nct6116:
> + data->in_num = 9;
> + data->pwm_num = 3;
> + data->auto_pwm_num = 4;
> + data->temp_fixed_num = 3;
> + data->num_temp_alarms = 3;
> + data->num_temp_beeps = 3;
> +
> + data->fan_from_reg = fan_from_reg13;
> + data->fan_from_reg_min = fan_from_reg13;
> +
> + data->temp_label = nct6776_temp_label;
> + data->temp_mask = NCT6776_TEMP_MASK;
> + data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
> +
> + data->REG_VBAT = NCT6116_REG_VBAT;
> + data->REG_DIODE = NCT6116_REG_DIODE;
> + data->DIODE_MASK = NCT6116_DIODE_MASK;
> + data->REG_VIN = NCT6116_REG_IN;
> + data->REG_IN_MINMAX[0] = NCT6116_REG_IN_MIN;
> + data->REG_IN_MINMAX[1] = NCT6116_REG_IN_MAX;
> + data->REG_TARGET = NCT6116_REG_TARGET;
> + data->REG_FAN = NCT6116_REG_FAN;
> + data->REG_FAN_MODE = NCT6116_REG_FAN_MODE;
> + data->REG_FAN_MIN = NCT6116_REG_FAN_MIN;
> + data->REG_FAN_PULSES = NCT6116_REG_FAN_PULSES;
> + data->FAN_PULSE_SHIFT = NCT6116_FAN_PULSE_SHIFT;
> + data->REG_FAN_TIME[0] = NCT6116_REG_FAN_STOP_TIME;
> + data->REG_FAN_TIME[1] = NCT6116_REG_FAN_STEP_UP_TIME;
> + data->REG_FAN_TIME[2] = NCT6116_REG_FAN_STEP_DOWN_TIME;
> + data->REG_TOLERANCE_H = NCT6116_REG_TOLERANCE_H;
> + data->REG_PWM[0] = NCT6116_REG_PWM;
> + data->REG_PWM[1] = NCT6116_REG_FAN_START_OUTPUT;
> + data->REG_PWM[2] = NCT6116_REG_FAN_STOP_OUTPUT;
> + data->REG_PWM[5] = NCT6116_REG_WEIGHT_DUTY_STEP;
> + data->REG_PWM[6] = NCT6116_REG_WEIGHT_DUTY_BASE;
> + data->REG_PWM_READ = NCT6116_REG_PWM_READ;
> + data->REG_PWM_MODE = NCT6116_REG_PWM_MODE;
> + data->PWM_MODE_MASK = NCT6116_PWM_MODE_MASK;
> + data->REG_AUTO_TEMP = NCT6116_REG_AUTO_TEMP;
> + data->REG_AUTO_PWM = NCT6116_REG_AUTO_PWM;
> + data->REG_CRITICAL_TEMP = NCT6116_REG_CRITICAL_TEMP;
> + data->REG_CRITICAL_TEMP_TOLERANCE
> + = NCT6116_REG_CRITICAL_TEMP_TOLERANCE;
> + data->REG_CRITICAL_PWM_ENABLE = NCT6116_REG_CRITICAL_PWM_ENABLE;
> + data->CRITICAL_PWM_ENABLE_MASK
> + = NCT6116_CRITICAL_PWM_ENABLE_MASK;
> + data->REG_CRITICAL_PWM = NCT6116_REG_CRITICAL_PWM;
> + data->REG_TEMP_OFFSET = NCT6116_REG_TEMP_OFFSET;
> + data->REG_TEMP_SOURCE = NCT6116_REG_TEMP_SOURCE;
> + data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
> + data->REG_WEIGHT_TEMP_SEL = NCT6116_REG_WEIGHT_TEMP_SEL;
> + data->REG_WEIGHT_TEMP[0] = NCT6116_REG_WEIGHT_TEMP_STEP;
> + data->REG_WEIGHT_TEMP[1] = NCT6116_REG_WEIGHT_TEMP_STEP_TOL;
> + data->REG_WEIGHT_TEMP[2] = NCT6116_REG_WEIGHT_TEMP_BASE;
> + data->REG_ALARM = NCT6116_REG_ALARM;
> + data->ALARM_BITS = NCT6116_ALARM_BITS;
> + data->REG_BEEP = NCT6116_REG_BEEP;
> + data->BEEP_BITS = NCT6116_BEEP_BITS;
> +
> + reg_temp = NCT6116_REG_TEMP;
> + reg_temp_mon = NCT6116_REG_TEMP_MON;
> + num_reg_temp = ARRAY_SIZE(NCT6116_REG_TEMP);
> + num_reg_temp_mon = ARRAY_SIZE(NCT6116_REG_TEMP_MON);
> + reg_temp_over = NCT6116_REG_TEMP_OVER;
> + reg_temp_hyst = NCT6116_REG_TEMP_HYST;
> + reg_temp_config = NCT6116_REG_TEMP_CONFIG;
> + reg_temp_alternate = NCT6116_REG_TEMP_ALTERNATE;
> + reg_temp_crit = NCT6116_REG_TEMP_CRIT;
> + reg_temp_crit_l = NCT6116_REG_TEMP_CRIT_L;
> + reg_temp_crit_h = NCT6116_REG_TEMP_CRIT_H;
> +
> + break;
> case nct6775:
> data->in_num = 9;
> data->pwm_num = 3;
> @@ -4366,6 +4563,7 @@
> data->have_vid = (cr2a & 0x60) == 0x40;
> break;
> case nct6106:
> + case nct6116:
> case nct6779:
> case nct6791:
> case nct6792:
> @@ -4397,6 +4595,9 @@
> case nct6106:
> tmp |= 0xe0;
> break;
> + case nct6116:
> + tmp |= 0xe0;
> + break;
> case nct6775:
> tmp |= 0x1e;
> break;
> @@ -4590,6 +4791,9 @@
> case SIO_NCT6106_ID:
> sio_data->kind = nct6106;
> break;
> + case SIO_NCT6116_ID:
> + sio_data->kind = nct6116;
> + break;
> case SIO_NCT6775_ID:
> sio_data->kind = nct6775;
> break;
>
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH] hwmon: (nct6775) Integrated new model nct6116
@ 2019-07-15 16:47 Björn Gerhart
2019-07-16 13:44 ` Guenter Roeck
0 siblings, 1 reply; 12+ messages in thread
From: Björn Gerhart @ 2019-07-15 16:47 UTC (permalink / raw)
To: Hardware Monitoring; +Cc: Guenter Roeck
Hello again and thanks for the early feedback! This is the re-worked patch of the one I sent last week. It’s created against kernel 5.1.15 and already depends on the preceding patch concerning the same code.
The nct6116 is the successor model of nct6106. Mainly, I’m unsure if certain details of the spec are mapped correctly to the code. These details are:
- NCT6116_BEEP_BITS
- int cr24 (cr23 is new, and I’m unsure if the code has to get modified therefore)
- NCT6116_REG_FAN_PULSES
- NCT6116_FAN_PULSE_SHIFT
- NCT6116_ALARM_BITS
With the nct6116 wired on my mainboard, the sensors command seems to work as I would expect.
Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
---
--- nct6775-5.1.15-1.el7.elrepo.x86_64-bugfixed/nct6775.c 2019-07-10 17:08:30.710690605 +0200
+++ nct6775/nct6775.c 2019-07-10 17:30:38.012416414 +0200
@@ -34,6 +34,7 @@
*
* Chip #vin #fan #pwm #temp chip IDs man ID
* nct6106d 9 3 3 6+3 0xc450 0xc1 0x5ca3
+ * nct6116d 9 5 5 3+3 0xd280 0xc1 0x5ca3
* nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3
* nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3
* nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3
@@ -72,12 +73,13 @@
#define USE_ALTERNATE
-enum kinds { nct6106, nct6775, nct6776, nct6779, nct6791, nct6792, nct6793,
- nct6795, nct6796, nct6797, nct6798 };
+enum kinds { nct6106, nct6116, nct6775, nct6776, nct6779, nct6791, nct6792,
+ nct6793, nct6795, nct6796, nct6797, nct6798 };
/* used to set data->name = nct6775_device_names[data->sio_kind] */
static const char * const nct6775_device_names[] = {
"nct6106",
+ "nct6116",
"nct6775",
"nct6776",
"nct6779",
@@ -92,6 +94,7 @@
static const char * const nct6775_sio_names[] __initconst = {
"NCT6106D",
+ "NCT6116D",
"NCT6775F",
"NCT6776D/F",
"NCT6779D",
@@ -129,6 +132,7 @@
#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
#define SIO_NCT6106_ID 0xc450
+#define SIO_NCT6116_ID 0xd280
#define SIO_NCT6775_ID 0xb470
#define SIO_NCT6776_ID 0xc330
#define SIO_NCT6779_ID 0xc560
@@ -910,6 +914,119 @@
[12] = 0x205,
};
+/* NCT6112D/NCT6114D/NCT6116D specific data */
+
+#define NCT6116_REG_VBAT 0x318
+#define NCT6116_REG_DIODE 0x319
+#define NCT6116_DIODE_MASK 0x01
+
+static const u16 NCT6116_REG_IN_MAX[] = {
+ 0x90, 0x92, 0x94, 0x96, 0x98, 0x9a, 0x9e, 0xa0, 0xa2 };
+static const u16 NCT6116_REG_IN_MIN[] = {
+ 0x91, 0x93, 0x95, 0x97, 0x99, 0x9b, 0x9f, 0xa1, 0xa3 };
+static const u16 NCT6116_REG_IN[] = {
+ 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x07, 0x08, 0x09 };
+
+static const u16 NCT6116_REG_TEMP[] = { 0x10, 0x11, 0x12 };
+static const u16 NCT6116_REG_TEMP_MON[] = { 0x18, 0x19, 0x1a };
+static const u16 NCT6116_REG_TEMP_HYST[] = { 0xc3, 0xc7, 0xcb };
+static const u16 NCT6116_REG_TEMP_OVER[] = { 0xc2, 0xc6, 0xca };
+static const u16 NCT6116_REG_TEMP_CRIT_L[] = { 0xc0, 0xc4, 0xc8 };
+static const u16 NCT6116_REG_TEMP_CRIT_H[] = { 0xc1, 0xc5, 0xc9 };
+static const u16 NCT6116_REG_TEMP_OFFSET[] = { 0x311, 0x312, 0x313 };
+static const u16 NCT6116_REG_TEMP_CONFIG[] = { 0xb7, 0xb8, 0xb9 };
+
+static const u16 NCT6116_REG_FAN[] = { 0x20, 0x22, 0x24, 0x26, 0x28 };
+static const u16 NCT6116_REG_FAN_MIN[] = { 0xe0, 0xe2, 0xe4, 0xe6, 0xe8 };
+static const u16 NCT6116_REG_FAN_PULSES[] = { 0xf6, 0xf6, 0xf6, 0xf6, 0xf5 };
+static const u16 NCT6116_FAN_PULSE_SHIFT[] = { 0, 2, 4, 6, 6 };
+
+static const u8 NCT6116_REG_PWM_MODE[] = { 0xf3, 0xf3, 0xf3 };
+static const u8 NCT6116_PWM_MODE_MASK[] = { 0x01, 0x02, 0x04 };
+static const u16 NCT6116_REG_PWM[] = { 0x119, 0x129, 0x139, 0x199, 0x1a9 };
+static const u16 NCT6116_REG_PWM_READ[] = { 0x4a, 0x4b, 0x4c };
+static const u16 NCT6116_REG_FAN_MODE[] = { 0x113, 0x123, 0x133, 0x193, 0x1a3 };
+static const u16 NCT6116_REG_TEMP_SEL[] = { 0x110, 0x120, 0x130, 0x190, 0x1a0 };
+static const u16 NCT6116_REG_TEMP_SOURCE[] = { 0xb0, 0xb1, 0xb2 };
+
+static const u16 NCT6116_REG_CRITICAL_TEMP[] = {
+ 0x11a, 0x12a, 0x13a, 0x19a, 0x1aa };
+static const u16 NCT6116_REG_CRITICAL_TEMP_TOLERANCE[] = {
+ 0x11b, 0x12b, 0x13b, 0x19b, 0x1ab };
+
+static const u16 NCT6116_REG_CRITICAL_PWM_ENABLE[] = {
+ 0x11c, 0x12c, 0x13c, 0x19c, 0x1ac };
+#define NCT6116_CRITICAL_PWM_ENABLE_MASK 0x10
+static const u16 NCT6116_REG_CRITICAL_PWM[] = {
+ 0x11d, 0x12d, 0x13d, 0x19d, 0x1ad };
+
+static const u16 NCT6116_REG_FAN_STEP_UP_TIME[] = {
+ 0x114, 0x124, 0x134, 0x194, 0x1a4 };
+static const u16 NCT6116_REG_FAN_STEP_DOWN_TIME[] = {
+ 0x115, 0x125, 0x135, 0x195, 0x1a5 };
+static const u16 NCT6116_REG_FAN_STOP_OUTPUT[] = {
+ 0x116, 0x126, 0x136, 0x196, 0x1a6 };
+static const u16 NCT6116_REG_FAN_START_OUTPUT[] = {
+ 0x117, 0x127, 0x137, 0x197, 0x1a7 };
+static const u16 NCT6116_REG_FAN_STOP_TIME[] = {
+ 0x118, 0x128, 0x138, 0x198, 0x1a8 };
+static const u16 NCT6116_REG_TOLERANCE_H[] = {
+ 0x112, 0x122, 0x132, 0x192, 0x1a2 };
+
+static const u16 NCT6116_REG_TARGET[] = {
+ 0x111, 0x121, 0x131, 0x191, 0x1a1 };
+
+static const u16 NCT6116_REG_WEIGHT_TEMP_SEL[] = { 0x168, 0x178, 0x188 };
+static const u16 NCT6116_REG_WEIGHT_TEMP_STEP[] = { 0x169, 0x179, 0x189 };
+static const u16 NCT6116_REG_WEIGHT_TEMP_STEP_TOL[] = { 0x16a, 0x17a, 0x18a };
+static const u16 NCT6116_REG_WEIGHT_DUTY_STEP[] = { 0x16b, 0x17b, 0x18b };
+static const u16 NCT6116_REG_WEIGHT_TEMP_BASE[] = { 0x16c, 0x17c, 0x18c };
+static const u16 NCT6116_REG_WEIGHT_DUTY_BASE[] = { 0x16d, 0x17d, 0x18d };
+
+static const u16 NCT6116_REG_AUTO_TEMP[] = {
+ 0x160, 0x170, 0x180, 0x1d0, 0x1e0 };
+static const u16 NCT6116_REG_AUTO_PWM[] = {
+ 0x164, 0x174, 0x184, 0x1d4, 0x1e4 };
+
+static const u16 NCT6116_REG_ALARM[NUM_REG_ALARM] = {
+ 0x77, 0x78, 0x79, 0x7a, 0x7b, 0x7c, 0x7d };
+
+static const s8 NCT6116_ALARM_BITS[] = {
+ 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
+ 9, -1, -1, -1, -1, -1, -1, /* in8..in9 */
+ -1, /* unused */
+ 32, 33, 34, 35, 36, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
+ 48, -1 /* intrusion0, intrusion1 */
+};
+
+static const u16 NCT6116_REG_BEEP[NUM_REG_BEEP] = {
+ 0x3c0, 0x3c1, 0x3c2, 0x3c3, 0x3c4 };
+
+static const s8 NCT6116_BEEP_BITS[] = {
+ 0, 1, 2, 3, 4, 5, 7, 8, /* in0.. in7 */
+ 9, 10, 11, 12, -1, -1, -1, /* in8..in14 */
+ 32, /* global beep enable */
+ 24, 25, 26, 27, 28, /* fan1..fan5 */
+ -1, -1, -1, /* unused */
+ 16, 17, 18, -1, -1, -1, /* temp1..temp6 */
+ 34, -1 /* intrusion0, intrusion1 */
+};
+
+static const u16 NCT6116_REG_TEMP_ALTERNATE[32] = {
+ [14] = 0x51,
+ [15] = 0x52,
+ [16] = 0x54,
+};
+
+static const u16 NCT6116_REG_TEMP_CRIT[32] = {
+ [11] = 0x204,
+ [12] = 0x205,
+};
+
+
+
static enum pwm_enable reg_to_pwm_enable(int pwm, int mode)
{
if (mode == 0 && pwm == 255)
@@ -1308,6 +1425,11 @@
return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
reg == 0xe0 || reg == 0xe2 || reg == 0xe4 ||
reg == 0x111 || reg == 0x121 || reg == 0x131;
+ case nct6116:
+ return reg == 0x20 || reg == 0x22 || reg == 0x24 ||
+ reg == 0x26 || reg == 0x28 || reg == 0xe0 || reg == 0xe2 ||
+ reg == 0xe4 || reg == 0xe6 || reg == 0xe8 || reg == 0x111 ||
+ reg == 0x121 || reg == 0x131 || reg == 0x191 || reg == 0x1a1;
case nct6775:
return (((reg & 0xff00) == 0x100 ||
(reg & 0xff00) == 0x200) &&
@@ -1687,6 +1809,7 @@
data->auto_pwm[i][data->auto_pwm_num] = 0xff;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3123,6 +3246,7 @@
case nct6776:
break; /* always enabled, nothing to do */
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -3544,7 +3668,7 @@
fan4min = fan4pin;
pwm3pin = fan3pin;
- } else if (data->kind == nct6106) {
+ } else if ((data->kind == nct6106) || (data->kind == nct6116)) {
int cr24 = superio_inb(sioreg, 0x24);
fan3pin = !(cr24 & 0x80);
@@ -3821,6 +3945,79 @@
reg_temp_crit_h = NCT6106_REG_TEMP_CRIT_H;
break;
+ case nct6116:
+ data->in_num = 9;
+ data->pwm_num = 3;
+ data->auto_pwm_num = 4;
+ data->temp_fixed_num = 3;
+ data->num_temp_alarms = 3;
+ data->num_temp_beeps = 3;
+
+ data->fan_from_reg = fan_from_reg13;
+ data->fan_from_reg_min = fan_from_reg13;
+
+ data->temp_label = nct6776_temp_label;
+ data->temp_mask = NCT6776_TEMP_MASK;
+ data->virt_temp_mask = NCT6776_VIRT_TEMP_MASK;
+
+ data->REG_VBAT = NCT6116_REG_VBAT;
+ data->REG_DIODE = NCT6116_REG_DIODE;
+ data->DIODE_MASK = NCT6116_DIODE_MASK;
+ data->REG_VIN = NCT6116_REG_IN;
+ data->REG_IN_MINMAX[0] = NCT6116_REG_IN_MIN;
+ data->REG_IN_MINMAX[1] = NCT6116_REG_IN_MAX;
+ data->REG_TARGET = NCT6116_REG_TARGET;
+ data->REG_FAN = NCT6116_REG_FAN;
+ data->REG_FAN_MODE = NCT6116_REG_FAN_MODE;
+ data->REG_FAN_MIN = NCT6116_REG_FAN_MIN;
+ data->REG_FAN_PULSES = NCT6116_REG_FAN_PULSES;
+ data->FAN_PULSE_SHIFT = NCT6116_FAN_PULSE_SHIFT;
+ data->REG_FAN_TIME[0] = NCT6116_REG_FAN_STOP_TIME;
+ data->REG_FAN_TIME[1] = NCT6116_REG_FAN_STEP_UP_TIME;
+ data->REG_FAN_TIME[2] = NCT6116_REG_FAN_STEP_DOWN_TIME;
+ data->REG_TOLERANCE_H = NCT6116_REG_TOLERANCE_H;
+ data->REG_PWM[0] = NCT6116_REG_PWM;
+ data->REG_PWM[1] = NCT6116_REG_FAN_START_OUTPUT;
+ data->REG_PWM[2] = NCT6116_REG_FAN_STOP_OUTPUT;
+ data->REG_PWM[5] = NCT6116_REG_WEIGHT_DUTY_STEP;
+ data->REG_PWM[6] = NCT6116_REG_WEIGHT_DUTY_BASE;
+ data->REG_PWM_READ = NCT6116_REG_PWM_READ;
+ data->REG_PWM_MODE = NCT6116_REG_PWM_MODE;
+ data->PWM_MODE_MASK = NCT6116_PWM_MODE_MASK;
+ data->REG_AUTO_TEMP = NCT6116_REG_AUTO_TEMP;
+ data->REG_AUTO_PWM = NCT6116_REG_AUTO_PWM;
+ data->REG_CRITICAL_TEMP = NCT6116_REG_CRITICAL_TEMP;
+ data->REG_CRITICAL_TEMP_TOLERANCE
+ = NCT6116_REG_CRITICAL_TEMP_TOLERANCE;
+ data->REG_CRITICAL_PWM_ENABLE = NCT6116_REG_CRITICAL_PWM_ENABLE;
+ data->CRITICAL_PWM_ENABLE_MASK
+ = NCT6116_CRITICAL_PWM_ENABLE_MASK;
+ data->REG_CRITICAL_PWM = NCT6116_REG_CRITICAL_PWM;
+ data->REG_TEMP_OFFSET = NCT6116_REG_TEMP_OFFSET;
+ data->REG_TEMP_SOURCE = NCT6116_REG_TEMP_SOURCE;
+ data->REG_TEMP_SEL = NCT6116_REG_TEMP_SEL;
+ data->REG_WEIGHT_TEMP_SEL = NCT6116_REG_WEIGHT_TEMP_SEL;
+ data->REG_WEIGHT_TEMP[0] = NCT6116_REG_WEIGHT_TEMP_STEP;
+ data->REG_WEIGHT_TEMP[1] = NCT6116_REG_WEIGHT_TEMP_STEP_TOL;
+ data->REG_WEIGHT_TEMP[2] = NCT6116_REG_WEIGHT_TEMP_BASE;
+ data->REG_ALARM = NCT6116_REG_ALARM;
+ data->ALARM_BITS = NCT6116_ALARM_BITS;
+ data->REG_BEEP = NCT6116_REG_BEEP;
+ data->BEEP_BITS = NCT6116_BEEP_BITS;
+
+ reg_temp = NCT6116_REG_TEMP;
+ reg_temp_mon = NCT6116_REG_TEMP_MON;
+ num_reg_temp = ARRAY_SIZE(NCT6116_REG_TEMP);
+ num_reg_temp_mon = ARRAY_SIZE(NCT6116_REG_TEMP_MON);
+ reg_temp_over = NCT6116_REG_TEMP_OVER;
+ reg_temp_hyst = NCT6116_REG_TEMP_HYST;
+ reg_temp_config = NCT6116_REG_TEMP_CONFIG;
+ reg_temp_alternate = NCT6116_REG_TEMP_ALTERNATE;
+ reg_temp_crit = NCT6116_REG_TEMP_CRIT;
+ reg_temp_crit_l = NCT6116_REG_TEMP_CRIT_L;
+ reg_temp_crit_h = NCT6116_REG_TEMP_CRIT_H;
+
+ break;
case nct6775:
data->in_num = 9;
data->pwm_num = 3;
@@ -4366,6 +4563,7 @@
data->have_vid = (cr2a & 0x60) == 0x40;
break;
case nct6106:
+ case nct6116:
case nct6779:
case nct6791:
case nct6792:
@@ -4397,6 +4595,9 @@
case nct6106:
tmp |= 0xe0;
break;
+ case nct6116:
+ tmp |= 0xe0;
+ break;
case nct6775:
tmp |= 0x1e;
break;
@@ -4590,6 +4791,9 @@
case SIO_NCT6106_ID:
sio_data->kind = nct6106;
break;
+ case SIO_NCT6116_ID:
+ sio_data->kind = nct6116;
+ break;
case SIO_NCT6775_ID:
sio_data->kind = nct6775;
break;
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2019-07-23 16:23 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-07-10 19:19 [PATCH] hwmon: (nct6775) Integrated new model nct6116 Björn Gerhart
2019-07-10 19:29 ` Björn Gerhart
2019-07-10 20:38 ` Guenter Roeck
2019-07-15 16:47 Björn Gerhart
2019-07-16 13:44 ` Guenter Roeck
2019-07-18 20:19 ` Björn Gerhart
2019-07-19 18:01 ` Björn Gerhart
2019-07-19 19:37 ` Guenter Roeck
2019-07-22 17:46 ` Björn Gerhart
2019-07-22 20:12 ` Guenter Roeck
2019-07-23 16:06 ` Björn Gerhart
2019-07-23 16:23 ` Guenter Roeck
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).