From: Guenter Roeck <linux@roeck-us.net>
To: Naveen Krishna Chatradhi <nchatrad@amd.com>,
linux-hwmon@vger.kernel.org, devicetree@vger.kernel.org
Cc: robh@kernel.org, jdelvare@suse.com, broonie@kernel.org,
Akshay Gupta <Akshay.Gupta@amd.com>
Subject: Re: [PATCH v4 1/3] hwmon: sbrmi: Add support for sbrmi power module
Date: Wed, 28 Jul 2021 09:57:52 -0700 [thread overview]
Message-ID: <e94f7785-70ab-8246-d695-e74a64a78e2e@roeck-us.net> (raw)
In-Reply-To: <20210726133615.9709-1-nchatrad@amd.com>
On 7/26/21 6:36 AM, Naveen Krishna Chatradhi wrote:
> From: Akshay Gupta <Akshay.Gupta@amd.com>
>
> On AMD platforms the Out-of-band access is provided by
> Advanced Platform Management Link (APML), APML is a
> SMBus v2.0 compatible 2-wire processor client interface.
> APML is also referred as the sideband interface (SBI).
>
> APML is used to communicate with the
> Side-Band Remote Management Interface (SB-RMI) which provides
> Soft Mailbox messages to manage power consumption and
> power limits of the CPU socket.
>
> - This module add support to read power consumption,
> power limit & max power limit and write power limit.
> - To instantiate this driver on a Board Management Controller (BMC)
> connected to an AMD CPU with SB-RMI support, the i2c bus number
> would be the bus connected from the BMC to the CPU.
>
> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> Signed-off-by: Akshay Gupta <Akshay.Gupta@amd.com>
> Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Series applied.
Thanks,
Guenter
> ---
> Changes since v3:
> Added reviewed by Guenter Roeck
>
> drivers/hwmon/Kconfig | 10 ++
> drivers/hwmon/Makefile | 1 +
> drivers/hwmon/sbrmi.c | 358 +++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 369 insertions(+)
> create mode 100644 drivers/hwmon/sbrmi.c
>
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 87624902ea80..f489972a6309 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -1551,6 +1551,16 @@ config SENSORS_SBTSI
> This driver can also be built as a module. If so, the module will
> be called sbtsi_temp.
>
> +config SENSORS_SBRMI
> + tristate "Emulated SB-RMI sensor"
> + depends on I2C
> + help
> + If you say yes here you get support for emulated RMI
> + sensors on AMD SoCs with APML interface connected to a BMC device.
> +
> + This driver can also be built as a module. If so, the module will
> + be called sbrmi.
> +
> config SENSORS_SHT15
> tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
> depends on GPIOLIB || COMPILE_TEST
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index 59e78bc212cf..8031acf58936 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -164,6 +164,7 @@ obj-$(CONFIG_SENSORS_PWM_FAN) += pwm-fan.o
> obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON) += raspberrypi-hwmon.o
> obj-$(CONFIG_SENSORS_S3C) += s3c-hwmon.o
> obj-$(CONFIG_SENSORS_SBTSI) += sbtsi_temp.o
> +obj-$(CONFIG_SENSORS_SBRMI) += sbrmi.o
> obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
> obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o
> obj-$(CONFIG_SENSORS_SCH5636) += sch5636.o
> diff --git a/drivers/hwmon/sbrmi.c b/drivers/hwmon/sbrmi.c
> new file mode 100644
> index 000000000000..372b099c04a0
> --- /dev/null
> +++ b/drivers/hwmon/sbrmi.c
> @@ -0,0 +1,358 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * sbrmi.c - hwmon driver for a SB-RMI mailbox
> + * compliant AMD SoC device.
> + *
> + * Copyright (C) 2020-2021 Advanced Micro Devices, Inc.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/hwmon.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/of.h>
> +
> +/* Do not allow setting negative power limit */
> +#define SBRMI_PWR_MIN 0
> +/* Mask for Status Register bit[1] */
> +#define SW_ALERT_MASK 0x2
> +
> +/* Software Interrupt for triggering */
> +#define START_CMD 0x80
> +#define TRIGGER_MAILBOX 0x01
> +
> +/*
> + * SB-RMI supports soft mailbox service request to MP1 (power management
> + * firmware) through SBRMI inbound/outbound message registers.
> + * SB-RMI message IDs
> + */
> +enum sbrmi_msg_id {
> + SBRMI_READ_PKG_PWR_CONSUMPTION = 0x1,
> + SBRMI_WRITE_PKG_PWR_LIMIT,
> + SBRMI_READ_PKG_PWR_LIMIT,
> + SBRMI_READ_PKG_MAX_PWR_LIMIT,
> +};
> +
> +/* SB-RMI registers */
> +enum sbrmi_reg {
> + SBRMI_CTRL = 0x01,
> + SBRMI_STATUS,
> + SBRMI_OUTBNDMSG0 = 0x30,
> + SBRMI_OUTBNDMSG1,
> + SBRMI_OUTBNDMSG2,
> + SBRMI_OUTBNDMSG3,
> + SBRMI_OUTBNDMSG4,
> + SBRMI_OUTBNDMSG5,
> + SBRMI_OUTBNDMSG6,
> + SBRMI_OUTBNDMSG7,
> + SBRMI_INBNDMSG0,
> + SBRMI_INBNDMSG1,
> + SBRMI_INBNDMSG2,
> + SBRMI_INBNDMSG3,
> + SBRMI_INBNDMSG4,
> + SBRMI_INBNDMSG5,
> + SBRMI_INBNDMSG6,
> + SBRMI_INBNDMSG7,
> + SBRMI_SW_INTERRUPT,
> +};
> +
> +/* Each client has this additional data */
> +struct sbrmi_data {
> + struct i2c_client *client;
> + struct mutex lock;
> + u32 pwr_limit_max;
> +};
> +
> +struct sbrmi_mailbox_msg {
> + u8 cmd;
> + bool read;
> + u32 data_in;
> + u32 data_out;
> +};
> +
> +static int sbrmi_enable_alert(struct i2c_client *client)
> +{
> + int ctrl;
> +
> + /*
> + * Enable the SB-RMI Software alert status
> + * by writing 0 to bit 4 of Control register(0x1)
> + */
> + ctrl = i2c_smbus_read_byte_data(client, SBRMI_CTRL);
> + if (ctrl < 0)
> + return ctrl;
> +
> + if (ctrl & 0x10) {
> + ctrl &= ~0x10;
> + return i2c_smbus_write_byte_data(client,
> + SBRMI_CTRL, ctrl);
> + }
> +
> + return 0;
> +}
> +
> +static int rmi_mailbox_xfer(struct sbrmi_data *data,
> + struct sbrmi_mailbox_msg *msg)
> +{
> + int i, ret, retry = 10;
> + int sw_status;
> + u8 byte;
> +
> + mutex_lock(&data->lock);
> +
> + /* Indicate firmware a command is to be serviced */
> + ret = i2c_smbus_write_byte_data(data->client,
> + SBRMI_INBNDMSG7, START_CMD);
> + if (ret < 0)
> + goto exit_unlock;
> +
> + /* Write the command to SBRMI::InBndMsg_inst0 */
> + ret = i2c_smbus_write_byte_data(data->client,
> + SBRMI_INBNDMSG0, msg->cmd);
> + if (ret < 0)
> + goto exit_unlock;
> +
> + /*
> + * For both read and write the initiator (BMC) writes
> + * Command Data In[31:0] to SBRMI::InBndMsg_inst[4:1]
> + * SBRMI_x3C(MSB):SBRMI_x39(LSB)
> + */
> + for (i = 0; i < 4; i++) {
> + byte = (msg->data_in >> i * 8) & 0xff;
> + ret = i2c_smbus_write_byte_data(data->client,
> + SBRMI_INBNDMSG1 + i, byte);
> + if (ret < 0)
> + goto exit_unlock;
> + }
> +
> + /*
> + * Write 0x01 to SBRMI::SoftwareInterrupt to notify firmware to
> + * perform the requested read or write command
> + */
> + ret = i2c_smbus_write_byte_data(data->client,
> + SBRMI_SW_INTERRUPT, TRIGGER_MAILBOX);
> + if (ret < 0)
> + goto exit_unlock;
> +
> + /*
> + * Firmware will write SBRMI::Status[SwAlertSts]=1 to generate
> + * an ALERT (if enabled) to initiator (BMC) to indicate completion
> + * of the requested command
> + */
> + do {
> + sw_status = i2c_smbus_read_byte_data(data->client,
> + SBRMI_STATUS);
> + if (sw_status < 0) {
> + ret = sw_status;
> + goto exit_unlock;
> + }
> + if (sw_status & SW_ALERT_MASK)
> + break;
> + usleep_range(50, 100);
> + } while (retry--);
> +
> + if (retry < 0) {
> + dev_err(&data->client->dev,
> + "Firmware fail to indicate command completion\n");
> + ret = -EIO;
> + goto exit_unlock;
> + }
> +
> + /*
> + * For a read operation, the initiator (BMC) reads the firmware
> + * response Command Data Out[31:0] from SBRMI::OutBndMsg_inst[4:1]
> + * {SBRMI_x34(MSB):SBRMI_x31(LSB)}.
> + */
> + if (msg->read) {
> + for (i = 0; i < 4; i++) {
> + ret = i2c_smbus_read_byte_data(data->client,
> + SBRMI_OUTBNDMSG1 + i);
> + if (ret < 0)
> + goto exit_unlock;
> + msg->data_out |= ret << i * 8;
> + }
> + }
> +
> + /*
> + * BMC must write 1'b1 to SBRMI::Status[SwAlertSts] to clear the
> + * ALERT to initiator
> + */
> + ret = i2c_smbus_write_byte_data(data->client, SBRMI_STATUS,
> + sw_status | SW_ALERT_MASK);
> +
> +exit_unlock:
> + mutex_unlock(&data->lock);
> + return ret;
> +}
> +
> +static int sbrmi_read(struct device *dev, enum hwmon_sensor_types type,
> + u32 attr, int channel, long *val)
> +{
> + struct sbrmi_data *data = dev_get_drvdata(dev);
> + struct sbrmi_mailbox_msg msg = { 0 };
> + int ret;
> +
> + if (type != hwmon_power)
> + return -EINVAL;
> +
> + msg.read = true;
> + switch (attr) {
> + case hwmon_power_input:
> + msg.cmd = SBRMI_READ_PKG_PWR_CONSUMPTION;
> + ret = rmi_mailbox_xfer(data, &msg);
> + break;
> + case hwmon_power_cap:
> + msg.cmd = SBRMI_READ_PKG_PWR_LIMIT;
> + ret = rmi_mailbox_xfer(data, &msg);
> + break;
> + case hwmon_power_cap_max:
> + msg.data_out = data->pwr_limit_max;
> + break;
> + default:
> + return -EINVAL;
> + }
> + if (ret < 0)
> + return ret;
> + /* hwmon power attributes are in microWatt */
> + *val = (long)msg.data_out * 1000;
> + return ret;
> +}
> +
> +static int sbrmi_write(struct device *dev, enum hwmon_sensor_types type,
> + u32 attr, int channel, long val)
> +{
> + struct sbrmi_data *data = dev_get_drvdata(dev);
> + struct sbrmi_mailbox_msg msg = { 0 };
> +
> + if (type != hwmon_power && attr != hwmon_power_cap)
> + return -EINVAL;
> + /*
> + * hwmon power attributes are in microWatt
> + * mailbox read/write is in mWatt
> + */
> + val /= 1000;
> +
> + val = clamp_val(val, SBRMI_PWR_MIN, data->pwr_limit_max);
> +
> + msg.cmd = SBRMI_WRITE_PKG_PWR_LIMIT;
> + msg.data_in = val;
> + msg.read = false;
> +
> + return rmi_mailbox_xfer(data, &msg);
> +}
> +
> +static umode_t sbrmi_is_visible(const void *data,
> + enum hwmon_sensor_types type,
> + u32 attr, int channel)
> +{
> + switch (type) {
> + case hwmon_power:
> + switch (attr) {
> + case hwmon_power_input:
> + case hwmon_power_cap_max:
> + return 0444;
> + case hwmon_power_cap:
> + return 0644;
> + }
> + break;
> + default:
> + break;
> + }
> + return 0;
> +}
> +
> +static const struct hwmon_channel_info *sbrmi_info[] = {
> + HWMON_CHANNEL_INFO(power,
> + HWMON_P_INPUT | HWMON_P_CAP | HWMON_P_CAP_MAX),
> + NULL
> +};
> +
> +static const struct hwmon_ops sbrmi_hwmon_ops = {
> + .is_visible = sbrmi_is_visible,
> + .read = sbrmi_read,
> + .write = sbrmi_write,
> +};
> +
> +static const struct hwmon_chip_info sbrmi_chip_info = {
> + .ops = &sbrmi_hwmon_ops,
> + .info = sbrmi_info,
> +};
> +
> +static int sbrmi_get_max_pwr_limit(struct sbrmi_data *data)
> +{
> + struct sbrmi_mailbox_msg msg = { 0 };
> + int ret;
> +
> + msg.cmd = SBRMI_READ_PKG_MAX_PWR_LIMIT;
> + msg.read = true;
> + ret = rmi_mailbox_xfer(data, &msg);
> + if (ret < 0)
> + return ret;
> + data->pwr_limit_max = msg.data_out;
> +
> + return ret;
> +}
> +
> +static int sbrmi_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &client->dev;
> + struct device *hwmon_dev;
> + struct sbrmi_data *data;
> + int ret;
> +
> + data = devm_kzalloc(dev, sizeof(struct sbrmi_data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + data->client = client;
> + mutex_init(&data->lock);
> +
> + /* Enable alert for SB-RMI sequence */
> + ret = sbrmi_enable_alert(client);
> + if (ret < 0)
> + return ret;
> +
> + /* Cache maximum power limit */
> + ret = sbrmi_get_max_pwr_limit(data);
> + if (ret < 0)
> + return ret;
> +
> + hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, data,
> + &sbrmi_chip_info, NULL);
> +
> + return PTR_ERR_OR_ZERO(hwmon_dev);
> +}
> +
> +static const struct i2c_device_id sbrmi_id[] = {
> + {"sbrmi", 0},
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, sbrmi_id);
> +
> +static const struct of_device_id __maybe_unused sbrmi_of_match[] = {
> + {
> + .compatible = "amd,sbrmi",
> + },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, sbrmi_of_match);
> +
> +static struct i2c_driver sbrmi_driver = {
> + .class = I2C_CLASS_HWMON,
> + .driver = {
> + .name = "sbrmi",
> + .of_match_table = of_match_ptr(sbrmi_of_match),
> + },
> + .probe = sbrmi_probe,
> + .id_table = sbrmi_id,
> +};
> +
> +module_i2c_driver(sbrmi_driver);
> +
> +MODULE_AUTHOR("Akshay Gupta <akshay.gupta@amd.com>");
> +MODULE_DESCRIPTION("Hwmon driver for AMD SB-RMI emulated sensor");
> +MODULE_LICENSE("GPL");
>
prev parent reply other threads:[~2021-07-28 16:57 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-25 13:25 [PATCH 1/3] hwmon: sbrmi: Add support for sbrmi power module Naveen Krishna Chatradhi
2021-06-25 13:25 ` [PATCH 2/3] hwmon: sbrmi: Add Documentation Naveen Krishna Chatradhi
2021-06-28 15:01 ` Guenter Roeck
2021-06-25 13:25 ` [PATCH 3/3] dt-bindings: sbrmi: Add SB-RMI hwmon driver bindings Naveen Krishna Chatradhi
2021-06-28 14:58 ` [PATCH 1/3] hwmon: sbrmi: Add support for sbrmi power module Guenter Roeck
2021-06-29 15:05 ` Chatradhi, Naveen Krishna
2021-07-07 14:14 ` Chatradhi, Naveen Krishna
2021-07-07 14:21 ` Guenter Roeck
2021-07-07 15:58 ` Chatradhi, Naveen Krishna
2021-07-07 15:58 ` [PATCH v2 " Naveen Krishna Chatradhi
2021-07-07 15:58 ` [PATCH v2 2/3] hwmon: sbrmi: Add Documentation Naveen Krishna Chatradhi
2021-07-07 15:58 ` [PATCH v2 3/3] dt-bindings: sbrmi: Add SB-RMI hwmon driver bindings Naveen Krishna Chatradhi
2021-07-16 5:58 ` [PATCH v2 1/3] hwmon: sbrmi: Add support for sbrmi power module Guenter Roeck
2021-07-19 15:50 ` Chatradhi, Naveen Krishna
2021-07-19 16:21 ` Guenter Roeck
2021-07-20 5:57 ` [PATCH v3 " Naveen Krishna Chatradhi
2021-07-20 5:57 ` [PATCH v3 2/3] hwmon: sbrmi: Add Documentation Naveen Krishna Chatradhi
2021-07-25 21:40 ` Guenter Roeck
2021-07-20 5:57 ` [PATCH v3 3/3] dt-bindings: sbrmi: Add SB-RMI hwmon driver bindings Naveen Krishna Chatradhi
2021-07-25 21:36 ` Guenter Roeck
2021-07-26 4:36 ` Chatradhi, Naveen Krishna
2021-07-26 4:58 ` Guenter Roeck
2021-07-25 21:38 ` [PATCH v3 1/3] hwmon: sbrmi: Add support for sbrmi power module Guenter Roeck
2021-07-26 13:36 ` [PATCH v4 " Naveen Krishna Chatradhi
2021-07-26 13:36 ` [PATCH v4 2/3] hwmon: sbrmi: Add Documentation Naveen Krishna Chatradhi
2021-07-26 13:36 ` [PATCH v4 3/3] dt-bindings: sbrmi: Add SB-RMI hwmon driver bindings Naveen Krishna Chatradhi
2021-07-26 22:43 ` Rob Herring
2021-07-28 16:57 ` Guenter Roeck [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=e94f7785-70ab-8246-d695-e74a64a78e2e@roeck-us.net \
--to=linux@roeck-us.net \
--cc=Akshay.Gupta@amd.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jdelvare@suse.com \
--cc=linux-hwmon@vger.kernel.org \
--cc=nchatrad@amd.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).