Linux-i2c Archive on lore.kernel.org
 help / color / Atom feed
From: Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>
To: spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
Cc: Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>,
	Fabio Estevam
	<fabio.estevam-KZfg59tc24xl57MIdRCFDg@public.gmane.org>,
	linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Subject: [PATCH V4] MXS: Implement DMA support into mxs-i2c
Date: Fri, 24 Aug 2012 05:44:31 +0200
Message-ID: <1345779871-7677-1-git-send-email-marex@denx.de> (raw)

This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.

Signed-off-by: Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>
CC: Fabio Estevam <fabio.estevam-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
CC: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Wolfram Sang <w.sang-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
---
 Documentation/devicetree/bindings/i2c/i2c-mxs.txt |    2 +
 arch/arm/boot/dts/imx28.dtsi                      |    2 +
 drivers/i2c/busses/i2c-mxs.c                      |  269 +++++++++++++++++++--
 3 files changed, 251 insertions(+), 22 deletions(-)

V2: Fixed return value from mxs_i2c_dma_setup_xfer().
    Fixed coding style nitpicks
    Call mxs_i2c_dma_finish() in failpath only if DMA is active
V3: Align with changes in previous patch
V4: Succumb to nonsense for the greater good ... like working EEPROMs
    Add "use_pioqueue" module parameter

diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
index 30ac3a0..7a3fe9e 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
@@ -6,6 +6,7 @@ Required properties:
 - interrupts: Should contain ERROR and DMA interrupts
 - clock-frequency: Desired I2C bus clock frequency in Hz.
                    Only 100000Hz and 400000Hz modes are supported.
+- fsl,i2c-dma-channel: APBX DMA channel for the I2C
 
 Examples:
 
@@ -16,4 +17,5 @@ i2c0: i2c@80058000 {
 	reg = <0x80058000 2000>;
 	interrupts = <111 68>;
 	clock-frequency = <100000>;
+	fsl,i2c-dma-channel = <6>;
 };
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index 3fa6d19..ba8227e 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -661,6 +661,7 @@
 				reg = <0x80058000 0x2000>;
 				interrupts = <111 68>;
 				clock-frequency = <100000>;
+				fsl,i2c-dma-channel = <6>;
 				status = "disabled";
 			};
 
@@ -671,6 +672,7 @@
 				reg = <0x8005a000 0x2000>;
 				interrupts = <110 69>;
 				clock-frequency = <100000>;
+				fsl,i2c-dma-channel = <7>;
 				status = "disabled";
 			};
 
diff --git a/drivers/i2c/busses/i2c-mxs.c b/drivers/i2c/busses/i2c-mxs.c
index 088c5c1..83c3a7e 100644
--- a/drivers/i2c/busses/i2c-mxs.c
+++ b/drivers/i2c/busses/i2c-mxs.c
@@ -7,8 +7,6 @@
  *
  * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
  *
- * TODO: add dma-support if platform-support for it is available
- *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
@@ -31,9 +29,16 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/of_i2c.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/fsl/mxs-dma.h>
 
 #define DRIVER_NAME "mxs-i2c"
 
+static bool use_pioqueue;
+module_param(use_pioqueue, bool, 0);
+MODULE_PARM_DESC(use_pioqueue, "Use PIOQUEUE mode for transfer instead of DMA");
+
 #define MXS_I2C_CTRL0		(0x00)
 #define MXS_I2C_CTRL0_SET	(0x04)
 
@@ -146,6 +151,16 @@ struct mxs_i2c_dev {
 	u32 cmd_err;
 	struct i2c_adapter adapter;
 	const struct mxs_i2c_speed_config *speed;
+
+	/* DMA support components */
+	bool				dma_mode;
+	int				dma_channel;
+	struct dma_chan         	*dmach;
+	struct mxs_dma_data		dma_data;
+	uint32_t			pio_data[2];
+	uint32_t			addr_data;
+	struct scatterlist		sg_io[2];
+	bool				dma_read;
 };
 
 static void mxs_i2c_reset(struct mxs_i2c_dev *i2c)
@@ -157,7 +172,11 @@ static void mxs_i2c_reset(struct mxs_i2c_dev *i2c)
 	writel(i2c->speed->timing2, i2c->regs + MXS_I2C_TIMING2);
 
 	writel(MXS_I2C_IRQ_MASK << 8, i2c->regs + MXS_I2C_CTRL1_SET);
-	writel(MXS_I2C_QUEUECTRL_PIO_QUEUE_MODE,
+	if (i2c->dma_mode)
+		writel(MXS_I2C_QUEUECTRL_PIO_QUEUE_MODE,
+			i2c->regs + MXS_I2C_QUEUECTRL_CLR);
+	else
+		writel(MXS_I2C_QUEUECTRL_PIO_QUEUE_MODE,
 			i2c->regs + MXS_I2C_QUEUECTRL_SET);
 }
 
@@ -248,6 +267,150 @@ static int mxs_i2c_finish_read(struct mxs_i2c_dev *i2c, u8 *buf, int len)
 	return 0;
 }
 
+static void mxs_i2c_dma_finish(struct mxs_i2c_dev *i2c)
+{
+	if (i2c->dma_read) {
+		dma_unmap_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE);
+		dma_unmap_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE);
+	} else {
+		dma_unmap_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE);
+	}
+}
+
+static void mxs_i2c_dma_irq_callback(void *param)
+{
+	struct mxs_i2c_dev *i2c = param;
+
+	complete(&i2c->cmd_complete);
+	mxs_i2c_dma_finish(i2c);
+}
+
+static int mxs_i2c_dma_setup_xfer(struct i2c_adapter *adap,
+			struct i2c_msg *msg, uint32_t flags)
+{
+	struct dma_async_tx_descriptor *desc;
+	struct mxs_i2c_dev *i2c = i2c_get_adapdata(adap);
+
+	if (msg->flags & I2C_M_RD) {
+		i2c->dma_read = 1;
+		i2c->addr_data = (msg->addr << 1) | I2C_SMBUS_READ;
+
+		/*
+		 * SELECT command.
+		 */
+
+		/* Queue the PIO register write transfer. */
+		i2c->pio_data[0] = MXS_CMD_I2C_SELECT;
+		desc = dmaengine_prep_slave_sg(i2c->dmach,
+					(struct scatterlist *)&i2c->pio_data[0],
+					1, DMA_TRANS_NONE, 0);
+		if (!desc) {
+			dev_err(i2c->dev,
+				"Failed to get PIO reg. write descriptor.\n");
+			goto select_init_pio_fail;
+		}
+
+		/* Queue the DMA data transfer. */
+		sg_init_one(&i2c->sg_io[0], &i2c->addr_data, 1);
+		dma_map_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE);
+		desc = dmaengine_prep_slave_sg(i2c->dmach, &i2c->sg_io[0], 1,
+					DMA_MEM_TO_DEV,
+					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+		if (!desc) {
+			dev_err(i2c->dev,
+				"Failed to get DMA data write descriptor.\n");
+			goto select_init_dma_fail;
+		}
+
+		/*
+		 * READ command.
+		 */
+
+		/* Queue the PIO register write transfer. */
+		i2c->pio_data[1] = flags | MXS_CMD_I2C_READ |
+				MXS_I2C_CTRL0_XFER_COUNT(msg->len);
+		desc = dmaengine_prep_slave_sg(i2c->dmach,
+					(struct scatterlist *)&i2c->pio_data[1],
+					1, DMA_TRANS_NONE, DMA_PREP_INTERRUPT);
+		if (!desc) {
+			dev_err(i2c->dev,
+				"Failed to get PIO reg. write descriptor.\n");
+			goto select_init_dma_fail;
+		}
+
+		/* Queue the DMA data transfer. */
+		sg_init_one(&i2c->sg_io[1], msg->buf, msg->len);
+		dma_map_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE);
+		desc = dmaengine_prep_slave_sg(i2c->dmach, &i2c->sg_io[1], 1,
+					DMA_DEV_TO_MEM,
+					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+		if (!desc) {
+			dev_err(i2c->dev,
+				"Failed to get DMA data write descriptor.\n");
+			goto read_init_dma_fail;
+		}
+	} else {
+		i2c->dma_read = 0;
+		i2c->addr_data = (msg->addr << 1) | I2C_SMBUS_WRITE;
+
+		/*
+		 * WRITE command.
+		 */
+
+		/* Queue the PIO register write transfer. */
+		i2c->pio_data[0] = flags | MXS_CMD_I2C_WRITE |
+				MXS_I2C_CTRL0_XFER_COUNT(msg->len + 1);
+		desc = dmaengine_prep_slave_sg(i2c->dmach,
+					(struct scatterlist *)&i2c->pio_data[0],
+					1, DMA_TRANS_NONE, 0);
+		if (!desc) {
+			dev_err(i2c->dev,
+				"Failed to get PIO reg. write descriptor.\n");
+			goto write_init_pio_fail;
+		}
+
+		/* Queue the DMA data transfer. */
+		sg_init_table(i2c->sg_io, 2);
+		sg_set_buf(&i2c->sg_io[0], &i2c->addr_data, 1);
+		sg_set_buf(&i2c->sg_io[1], msg->buf, msg->len);
+		dma_map_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE);
+		desc = dmaengine_prep_slave_sg(i2c->dmach, i2c->sg_io, 2,
+					DMA_MEM_TO_DEV,
+					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+		if (!desc) {
+			dev_err(i2c->dev,
+				"Failed to get DMA data write descriptor.\n");
+			goto write_init_dma_fail;
+		}
+	}
+
+	/*
+	 * The last descriptor must have this callback,
+	 * to finish the DMA transaction.
+	 */
+	desc->callback = mxs_i2c_dma_irq_callback;
+	desc->callback_param = i2c;
+
+	/* Start the transfer. */
+	dmaengine_submit(desc);
+	dma_async_issue_pending(i2c->dmach);
+	return 0;
+
+/* Read failpath. */
+read_init_dma_fail:
+	dma_unmap_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE);
+select_init_dma_fail:
+	dma_unmap_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE);
+select_init_pio_fail:
+	return -EINVAL;
+
+/* Write failpath. */
+write_init_dma_fail:
+	dma_unmap_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE);
+write_init_pio_fail:
+	return -EINVAL;
+}
+
 /*
  * Low level master read/write transaction.
  */
@@ -258,6 +421,8 @@ static int mxs_i2c_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg,
 	int ret;
 	int flags;
 
+	flags = stop ? MXS_I2C_CTRL0_POST_SEND_STOP : 0;
+
 	dev_dbg(i2c->dev, "addr: 0x%04x, len: %d, flags: 0x%x, stop: %d\n",
 		msg->addr, msg->len, msg->flags, stop);
 
@@ -267,23 +432,29 @@ static int mxs_i2c_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg,
 	init_completion(&i2c->cmd_complete);
 	i2c->cmd_err = 0;
 
-	flags = stop ? MXS_I2C_CTRL0_POST_SEND_STOP : 0;
-
-	if (msg->flags & I2C_M_RD)
-		mxs_i2c_pioq_setup_read(i2c, msg->addr, msg->len, flags);
-	else
-		mxs_i2c_pioq_setup_write(i2c, msg->addr, msg->buf, msg->len,
-					flags);
+	if (i2c->dma_mode) {
+		ret = mxs_i2c_dma_setup_xfer(adap, msg, flags);
+		if (ret)
+			return ret;
+	} else {
+		if (msg->flags & I2C_M_RD) {
+			mxs_i2c_pioq_setup_read(i2c, msg->addr,
+						msg->len, flags);
+		} else {
+			mxs_i2c_pioq_setup_write(i2c, msg->addr, msg->buf,
+						msg->len, flags);
+		}
 
-	writel(MXS_I2C_QUEUECTRL_QUEUE_RUN,
+		writel(MXS_I2C_QUEUECTRL_QUEUE_RUN,
 			i2c->regs + MXS_I2C_QUEUECTRL_SET);
+	}
 
 	ret = wait_for_completion_timeout(&i2c->cmd_complete,
 						msecs_to_jiffies(1000));
 	if (ret == 0)
 		goto timeout;
 
-	if ((!i2c->cmd_err) && (msg->flags & I2C_M_RD)) {
+	if (!i2c->dma_mode && !i2c->cmd_err && (msg->flags & I2C_M_RD)) {
 		ret = mxs_i2c_finish_read(i2c, msg->buf, msg->len);
 		if (ret)
 			goto timeout;
@@ -301,6 +472,8 @@ static int mxs_i2c_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg,
 
 timeout:
 	dev_dbg(i2c->dev, "Timeout!\n");
+	if (i2c->dma_mode)
+		mxs_i2c_dma_finish(i2c);
 	mxs_i2c_reset(i2c);
 	return -ETIMEDOUT;
 }
@@ -342,11 +515,13 @@ static irqreturn_t mxs_i2c_isr(int this_irq, void *dev_id)
 		/* MXS_I2C_CTRL1_OVERSIZE_XFER_TERM_IRQ is only for slaves */
 		i2c->cmd_err = -EIO;
 
-	is_last_cmd = (readl(i2c->regs + MXS_I2C_QUEUESTAT) &
-		MXS_I2C_QUEUESTAT_WRITE_QUEUE_CNT_MASK) == 0;
+	if (!i2c->dma_mode) {
+		is_last_cmd = (readl(i2c->regs + MXS_I2C_QUEUESTAT) &
+			MXS_I2C_QUEUESTAT_WRITE_QUEUE_CNT_MASK) == 0;
 
-	if (is_last_cmd || i2c->cmd_err)
-		complete(&i2c->cmd_complete);
+		if (is_last_cmd || i2c->cmd_err)
+			complete(&i2c->cmd_complete);
+	}
 
 	writel(stat, i2c->regs + MXS_I2C_CTRL1_CLR);
 
@@ -358,6 +533,21 @@ static const struct i2c_algorithm mxs_i2c_algo = {
 	.functionality = mxs_i2c_func,
 };
 
+static bool mxs_i2c_dma_filter(struct dma_chan *chan, void *param)
+{
+	struct mxs_i2c_dev *i2c = param;
+
+	if (!mxs_dma_is_apbx(chan))
+		return false;
+
+	if (chan->chan_id != i2c->dma_channel)
+		return false;
+
+	chan->private = &i2c->dma_data;
+
+	return true;
+}
+
 static int mxs_i2c_get_ofdata(struct mxs_i2c_dev *i2c)
 {
 	uint32_t speed;
@@ -368,6 +558,26 @@ static int mxs_i2c_get_ofdata(struct mxs_i2c_dev *i2c)
 	if (!node)
 		return -EINVAL;
 
+	/*
+	 * The MXS I2C DMA mode is prefered and enabled by default.
+	 * The PIO mode is still supported, but should be used only
+	 * for debuging purposes etc.
+	 */
+	i2c->dma_mode = !use_pioqueue;
+	if (!i2c->dma_mode)
+		dev_info(dev, "Using PIOQUEUE mode for I2C transfers!\n");
+
+	/*
+	 * TODO: This is a temporary solution and should be changed
+	 * to use generic DMA binding later when the helpers get in.
+	 */
+	ret = of_property_read_u32(node, "fsl,i2c-dma-channel",
+				   &i2c->dma_channel);
+	if (ret) {
+		dev_warn(dev, "Failed to get DMA channel, using PIOQUEUE!\n");
+		i2c->dma_mode = 0;
+	}
+
 	i2c->speed = &mxs_i2c_95kHz_config;
 	ret = of_property_read_u32(node, "clock-frequency", &speed);
 	if (ret)
@@ -388,7 +598,8 @@ static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 	struct pinctrl *pinctrl;
 	struct resource *res;
 	resource_size_t res_size;
-	int err, irq;
+	int err, irq, dmairq;
+	dma_cap_mask_t mask;
 
 	pinctrl = devm_pinctrl_get_select_default(dev);
 	if (IS_ERR(pinctrl))
@@ -399,7 +610,10 @@ static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res)
+	irq = platform_get_irq(pdev, 0);
+	dmairq = platform_get_irq(pdev, 1);
+
+	if (!res || irq < 0 || dmairq < 0)
 		return -ENOENT;
 
 	res_size = resource_size(res);
@@ -410,10 +624,6 @@ static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 	if (!i2c->regs)
 		return -EBUSY;
 
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0)
-		return irq;
-
 	err = devm_request_irq(dev, irq, mxs_i2c_isr, 0, dev_name(dev), i2c);
 	if (err)
 		return err;
@@ -424,6 +634,18 @@ static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 	if (err)
 		return err;
 
+	/* Setup the DMA */
+	if (i2c->dma_mode) {
+		dma_cap_zero(mask);
+		dma_cap_set(DMA_SLAVE, mask);
+		i2c->dma_data.chan_irq = dmairq;
+		i2c->dmach = dma_request_channel(mask, mxs_i2c_dma_filter, i2c);
+		if (!i2c->dmach) {
+			dev_err(dev, "Failed to request dma\n");
+			return -ENODEV;
+		}
+	}
+
 	platform_set_drvdata(pdev, i2c);
 
 	/* Do reset to enforce correct startup after pinmuxing */
@@ -459,6 +681,9 @@ static int __devexit mxs_i2c_remove(struct platform_device *pdev)
 	if (ret)
 		return -EBUSY;
 
+	if (i2c->dmach)
+		dma_release_channel(i2c->dmach);
+
 	writel(MXS_I2C_CTRL0_SFTRST, i2c->regs + MXS_I2C_CTRL0_SET);
 
 	platform_set_drvdata(pdev, NULL);
-- 
1.7.10.4


------------------------------------------------------------------------------
Live Security Virtual Conference
Exclusive live event will cover all the ways today's security and 
threat landscape has changed and how IT managers can respond. Discussions 
will include endpoint security, mobile security and the latest in malware 
threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/

             reply index

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-08-24  3:44 Marek Vasut [this message]
     [not found] ` <1345779871-7677-1-git-send-email-marex-ynQEQJNshbs@public.gmane.org>
2012-08-27 18:54   ` Fabio Estevam
     [not found]     ` <CAOMZO5CSvP3nXNq4VLYALh+U9OZRnjtgXqTr7zsKdeHpUdJ4cQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2012-09-16 10:44       ` Wolfram Sang
     [not found]         ` <20120916104436.GC933-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2012-09-16 14:44           ` Fabio Estevam
2012-09-16 10:23   ` Wolfram Sang
     [not found]     ` <20120916102342.GA933-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2012-09-16 10:51       ` Marek Vasut
     [not found]         ` <201209161251.41895.marex-ynQEQJNshbs@public.gmane.org>
2012-09-16 11:12           ` Wolfram Sang
     [not found]             ` <20120916111223.GD933-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2012-09-16 11:14               ` Marek Vasut
2012-09-27  0:03               ` Marek Vasut
2012-10-08  9:25   ` Wolfram Sang
     [not found]     ` <20121008092530.GA22051-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2012-10-08 13:15       ` Marek Vasut

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1345779871-7677-1-git-send-email-marex@denx.de \
    --to=marex-ynqeqjnshbs@public.gmane.org \
    --cc=fabio.estevam-KZfg59tc24xl57MIdRCFDg@public.gmane.org \
    --cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
    --cc=linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
    --cc=spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-i2c Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-i2c/0 linux-i2c/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-i2c linux-i2c/ https://lore.kernel.org/linux-i2c \
		linux-i2c@vger.kernel.org
	public-inbox-index linux-i2c

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-i2c


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git